Standby Switch for 6509

My 6509 Backplane traffic Max. is 10% which means 25Gbps. in my earlier conversation i was telling i am going to put 3750(32Gbps), but need to know what is the backplane traffic of 4510R, & is it going to cost more or just a little bit price difference than 3750? 3750 i planned for 3 Nos. Thanks in advance.

Anand,
The backplane for 4510R depends on the Sup engine you have, For example with Sup 5-10 GE it has 136 GBPS. Sup V has 96 GBPS, SUP4,3 and sup 2+ has 64 GbPS. I think it will cost more than the 3 No 3750's depending on which 3750 model you take. The chassis 4510 only costs arnd 12500 US$ without any line card. So I would suggest you contact Cisco Pre-sales team or any reseller and get the price check and then take the decision accordingly.
http://www.cisco.com/en/US/partner/products/hw/switches/ps4324/products_data_sheet09186a0080197424.html
regards,
-amit singh

Similar Messages

Which is good: ejecting or standby mode for EHD's?

After a session at the computer, I have this dilemna: how to close down the session. At this present moment of time, I have a thunderbolt, a 2TB FW LaCie, and three Seagate [2 USB] EHD's all connected to my Mac. All the three Seagate drives have been allocated backup roles via CCC and TM.
In this scenario, what should be the manner of my quitting a session at the computer? Will keeping the EHD's in a standby mode for prolonged periods damage them?
Also, I would like to know what is the difference between mounting/unmounting of a drive and ejection of drive?

somanna wrote:
I guess I need to set my own 'protocol' in these matters.
Indeed
somanna wrote:
I need to tackle my own 'temporary laziness' and take time to do these things: eject the thunderbolt drive which I use for editing videos in FCPX. [After doing an 'eject' do I have to also disconnect the power supply by pulling out the thunderbolt cable from the drive? By so doing, the CCC based backup would not take place.
No it should go into standby without disconnecting it.
That is correct, if it is disconnected then CCC will not backup. If you are using the same drive for editing and CCC, then you will need to test it to see if CCC will bring it backup from standby. If not, then maybe that is not a good combination of uses for one drive.
somanna wrote:
My LaCie has a power switch. Is it okay to directly switch it off or do I have to first click upon its desktop icon and eject it? But if I switch off its power, then will CCC automatically start up the power and at its set time backup the data on this Lacie to its concerned backup drive, a Seagate?
No you should first Eject it before Switching it off.
No CCC will not turn it back on.
No
somanna wrote:
The 2 other Seagate drives also have got some functions to do regarding backups. These Seagate drives have no power switches. Should I just eject these drives and keep their power cables on or do I have to also have to remove their power supply cables from the drives after they are ejected.
As with any automated backup, the drive(s) must be connected and powered on in order for the automated backup to take place.
somanna wrote:
Further guidance and instructions in these matters will be highly appreciated.
While I also get a little anal about backup, I do like to save power whenever I can.
To be honest, I would probably only use the Thunderbolt drive for editing and keep one other drive online to back it up. Then rotate the other drives in and out on a daily or weekly basis keeping them off line, off site or at least in a firesafe.
Keep at least one or two aces up your sleeve! Heck' a single lighting strike, power surge or simple mistake could take out everything in the blink of an eye if it's all hooked together and running.

Netra t1 with solaris 9 fresh install on/standby switch

Hi,
I recently installed solaris 9 onto my Netra 105 box. For the likes off me I can't figure out why the on/standby switch simply does not work since reinstalling. The only way I can power down the box is by literally unplugging it from the wall. I am a total newbie to Sun boxes (& solaris for that matter) & have had zero luck in finding any info specific info relating to this. Can some kind soul put me on the right track?

I have down precisely what you have recommended & the thing still won't go into standby. After executing poweroff from the LOM prompt It just sits there continually humming away. Yet it worked fine prior to the installation off solaris 9 from solaris 8. I have even reinstalled again, this time making sure to include the power management options. All reinstalls were done with the "initial installation" option.
Here is a screen dump off the unit booting & me executing the poweroff commnd:
lom>reset
LOM event: host reset
Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.25 ME, 512 MB memory installed, Serial #14315586.
Ethernet address 8:0:20:da:70:42, Host ID: 80da7042.
Boot device: disk File and args:
SunOS Release 5.9 Version Generic_112233-05 64-bit
Copyright 1983-2002 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
configuring IPv4 interfaces: hme0.
configuring IPv6 interfaces: hme0.
starting DHCP on primary interface hme0
Hostname: unknown
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c0t0d0s7: is stable.
Starting IPv6 neighbor discovery.
Setting default IPv6 interface for multicast: add net ff00::/8: gateway fe80::a00:20ff:feda:7042
starting rpc services: rpcbind done.
Setting default IPv4 interface for multicast: add net 224.0/4: gateway 192.168.0.125
syslog service starting.
syslogd: line 24: WARNING: loghost could not be resolved
Jun 27 19:19:36 unknown /usr/lib/power/powerd: powerd: failed to get idle time for console mouse
volume management starting.
The system is ready.
unknown console login: root
Password:
Last login: Fri Jun 27 19:00:09 on console
Jun 27 19:19:55 unknown login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.9 Generic May 2002
# #.lom>poweroff
lom>
This problem is annoying the hell out off me. Everyone I have spoken to hasn't even heard off this problem.
Any other advice you can give would be very much appreciated.

Cold Standby Server for Crystal Reports Server...

Hi there,
We have the confirmation from Hong Kong SAP that Crystal Reports Server 2008 does not come with any clustering feature as Business Objects Enterprise does. We are to set up a cold standby server for the production server for high availability. Below is our procedures to work it out:
1) we set up two machines for CRS 2008 with the same licence key and identical hardware; otherwise we clone the production machine to an identical hardware for a cold standby machine
2) we are using our Oracle instance (same instance for both the production and the standby one) for CRS 2008 repository; we bring the production sever offline and perform the standby server installation of CRS 2008 without resetting the repository Oracle database
3) we are to use a SAN LUN for storing the reports produced by CRS 2008
Once the production server does not work properly due to any hardware problem, we switch it off manually and turn on the standby machine and the Crystal Reports service should resume with no repository problem (all the settings) and no loss of printed reports. We would be grateful if you could confirm the feasibility of these procedures. Thanks a lot.
Regards,
Jason FU

Correct, CRS is for a single machine use only, that why it is not as expensive as the full BOE. Talk to Sales to upgrade.

Remote deployment switches for Jabber 9.2.2

Are there any installation switches for remote install via the MSI/DMG?
I will be pushing this backage via Dell KACE K1000 appliance and would like to configure default options for the users during the install/upgrade such as Disabling (or 'unchecked' following initial sign-on) the Docked Window, configuring Phone Accounts, WebEx Meeting and application Integration settings.

application integrations setting mostly get pushed out through the profiles on CUPS that get pushed out as soon as the user logs in.
I can't help you out with all the switches you asked for but, you can starting using:
msiexec.exe /i "\\lsrftufs1\ict\Networks\Voice\Jabber\Jabber 9.2.2\CiscoJabberSetup.msi" TYPE=CUP DOMAIN=somedomain.com.au LANGUAGE=1033
This will at least use auto discovery of the presence server if you use an SRV record _cup._login.somedomain.com.au
so at least your useers wont have to type in a presence server name or IP.
=============================
Please remember to rate useful posts, by clicking on the stars below.
=============================

Time Capsule - Can it run as DHCP router, create a wireless network and plug into switch for wired network all at the same time?

I have a closet with Wired connections from all over the house terminating in it. I also have the internet modem and a switch in this closet. My old setup was a netgear in the closet creating a wireless network and also feeding the Ethernet ports all over the house. In my room, I had an Airport express (a month old) bridging the wifi to make the wifi network larger. The Express was hard wired from the wall and my mac mini was using it's wifi (printer was plugged into other ethernet port). Everything was working great.
Fast forward to last week. My Netgear died. So, I bought a time capsule. My plan was to move the Express to the closet and have it create the wifi network and also then run cat 5 cord from express to the switch to feed all the wired wall plugs. Reset it and set it up to create the wifi network as well as DCHP NAT. Wireless was running great on it. Then I plugged in the Cat 5 in the second Ethernet Port to the switch. Wifi stopped working and none of the computers would connect using wired connections either. They would see a 'network' but nothing would work. I would unplug the Cat 5 feeding the swtich and the wireless would start working again. Plug the Cat 5 back in and wireless would stop.
So I thought I would try the Time Capsule in the closet and see if I could get it to work. Pretty much the same thing, except at this point I figured out if I went in and told it NOT to create a wifi network the wired portion worked fine and all the wired computers in the house worked fine. Of course, then I didn't have Wifi.
I'm not clueless when it comes to networking, but I can NOT figure this out! Can either the Time Capsule or Express Create the wifi network AND also feed the data to the switch for all the wired computers?
To simplify this is what I want my end result to be. I prefer the Time Capsule to be the wireless connection extender, but if I have to have the Express do it, I'm fine with that.
1. Express in the closet creating the wifi network as well as feeding the data to the wired connections via my switch.
2. have the Time capsule in my room at the opposite end of the house plugged into the hard wired connection to extend the wrieless network as well as have wired connections such as my printer and my Mac Mini.
If I can get #1 to work, I don't think I'll have any problems with #2. Help!

I have an equally complex setup with a managed switch actually but I have never seen the TC have this kind of issue.
What I do notice is you have changed the TC from defaults.. you are using a non-default IP range.
I have run across issues like this where people move things from default.
I would like you to start over.. factory reset the TC. That will set it back to default router mode.
Do the min setup on the TC..
1. Change all names from what you were using. That includes the TC name and wireless name/s
Make them short, no spaces and pure alphanumeric because that is the correct way to network. Apple default names with spaces and apostrophes are fundamentally bad.
2. With just the TC plugged into the switch.. and a single computer connected by ethernet. Power cycle the whole network.. this allows the switch to clear all the old MAC address.
3. Test on the computer just ethernet. Turn the wireless off.
The computer must use dhcp and must get an ip from the TC.
It has to get the correct Router.. ie Gateway.. I wish apple could stick with proper network terminology.
And it must get same address or valid DNS server address/es.
If it fails.. please plug ethernet directly to the TC.. bypassing the switch.
You should get the standard IP addressing and internet connection.
If not please post the screenshot from the Mac of the network preferences showing the ethernet setup.
I need to see what address it does get. I need you to make sure the ethernet is the TOP of the list. So rearrange the order of network connection. With the airport off it should just go to the top of the list.
If it appears to be working .. but a browser cannot connect, open a terminal and ping an internet address.
Ping the actual gateway address the ISP gives you and ping the ISP dns address.

Locked button & switch for volume is broke also back is cracked , can i get my phone replaced for free ?

my lock button and the switch to turn the volume on & off is broke. also the back of my phone is cracked. i know apple doesn't replace cracked phones so would i have to pay for a replacement even though my lock button & the switch for the volume is broke ? if so , how much ? or would if be cheaper to just but a whole new iPhone ?

If your damage is caused by accidental damage or intentional user damage, then you would be looking at an out of warranty repair. I'm not sure what the costs of an out of warranty repair are for an iPhone 4, but they are probably in the $99-149 USD range.
The cost for getting a new iPhone would depend upon your current contract status. If you are out of contract, you can get a new iPhone 4s (the next newer model) for free.

Dynamic Environment Switching For REPORTS_PATH 11g

Oracle Fusion Middleware 11.1.1.2.0 with Patch Set 2 (11.1.1.3.0) - Linux
Dynamic Environment Switching For REPORTS_PATH doesn't work.
According to documentation B32121-03 (Publishing Reports to the Web with Oracle Reports Services 11g Release 1 (11.1.1) point 8.2.2):
1. comment REPORTS_PATH in reports.sh
2. set enviroment settings in rwserver.conf with REPORTS_PATH and NLS_LANG and defaultEnvId (DEV and PRD with defaultEnvId="DEV")
3. restart reports server
4. run http://mywls:8888/reports/rwservlet?SERVER=rep_wls_reports_mywls_asinst_1&REPORT=testreport.rdf&USERID=user/user1@mydb&DESFORMAT=html&DESTYPE=cache&ENVID=DEV
REP-110: File testreport.rdf cannot be opened.
REP-1070: An error occurred while opening or saving a document.
REP-0110: File testreport.rdf cannot be opened.
The same situation for &ENVID=PRD or without ENVID (as I expect it should work as default - DEV enviroment). File testreport.rdf is located in both paths (/u00/DEV/reports and /u00/PRD/reports)
http://mywls:8888/reports/rwservlet/showenv?server=rep_wls_reports_mywls_asinst_1&authid=oiduser/oiduser1 reads informations from reports.sh file but doesn't read enviroment settings from rwserver.conf (REPORTS_PATH is empty because I comment it in reports.sh).
Where's my problem? Should I set any other setting(s)?
Unfortunately note [231051.1] and other referenced doesn't resolve my problem...
Edited by: user9093781 on 2011-08-23 06:50

Not sure if this helps at all. I just went through a nightmare trying to get 11g forms/reports to work through the forms builder.
What I discovered with that is that I indeed had to set the REPORTS_PATH in rwserver.conf... however there were 3 different files that I ended up having to put it in (not sure if had to be in all 3). And perhaps more importantly, there seems to be an order to how you put these xml statements in the rwserver.conf files.
In my case, it wouldn't work at all until I put it right after the last "<engine id=" statement.
Mine looks something like this (not that this is a snippet of the file in Windows, for running via Forms/Reports Builder):
<engine id="rwURLEng" class="oracle.reports.urlengine.URLEngineImpl" maxEngine="1" minEngine="0" engLife="50"/>
<environment id="default">
     <envVariable value="C:\Oracle\WLS11gR1U4\user_projects\domains\AISworkstation\" name="REPORTS_PATH"/>
     <envVariable value="AMERICAN_AMERICA.WE8ISO8859P1" name="NLS_LANG"/>
     <envVariable value="RRRR-MM-DD" name="NLS_DATE_FORMAT"/>
</environment>
<environment id="windev_xxxxxxxx">
<envVariable name="REPORTS_PATH"
value="M:\ADS\Dvlprs\xxxxxxx\11g\FormsApps\stage;M:\ADS\Dvlprs\xxxxxxx\11g\FormsApps"/>
</environment>
I'm still figuring this all out too (although I did get it working how I need.. just not sure if it is the optimal solution), so I'm not sure how much this will help you. But for sure I can say that there is an order to these XML tags that I'm not so sure was the same (or maybe not enforced) in 10g.
Good luck

Silent Uninstall Switch for FlashUtil32_11_4_402_278_ActiveX.exe

I know I can run 'FlashUtil32_11_4_402_278_ActiveX.exe' (found in 'C:\Windows\System32\Macromed\Flash') manually, but I'd like to automate the removal process to avoid having the user click on anything. (I want zero user interaction!)
Are there any silent/unattended switches for FlashUtil32?

Hi Pat & thank you kindly for at least responding to the thread. I greatly appreciate it.
For what its worth the -uninstall switch works for the following executables in C:\Windows\System32\Macromed\Flash:
FlashPlayerPlugin_11_XXX.exe
FlashPlayerUpdateService.exe
FlashUtil32_11_XXX_Plugin.exe
It does not seem to work for the FlashUtil32_11_XXX_ActiveX.exe. However, as you pointed out, it does work with the uninstall_flash_player.exe, and that seems to get rid of the last remaining FlashUtil32_11_XXX_ActiveX.exe file (among other things I'm sure).
Thanks!

Switch for showing my telephonenumber locked

The switch for showing my number is locked. My iPhone shows unknown number when I call someone. I think it has something to do with my iCloud account. I tried to put my SIM card into another iPhone and my number showed. So I got a new iPhone and downloaded my iCloud profile to the new iPhone and the same problem was back. I started this iCloud profile with a 3s iPhone with a diffrent telephone company and a diffrent telephone number. Any thoughts?

The carrier I'm using is connected to my office and several of my colleagues uses iCloud and doesn't have this problem.
I have my old mobile number divert to this number I'm using now. Can that cause this problem?

Switch for Distribution Layer

I need your expert opinions for selecting a switch for distribution Layer
My requirement is 24Gig ports @ dist layer which will connect to 3750?s for server farm. I don?t want to negotiate with the bandwidth.
Which switch will be best for this scenario with max Backplane speed

Yes L3 routing will there.
I am considering 3750 for access switch for my server farm, and 4506 for distribution layer with the following port requirement
Catalyst 4500 Gigabit Ethernet Module, 6-Ports (GBIC)
Catalyst 4500 GE Module, Server Switching 18-Ports (GBIC)
Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45)
Catalyst 4500 Supervisor IV (2 GE), Console (RJ-45)
Most of the gigabit port will be occupied since I have a huge server farm to connect. By using almost all the ports on 4506 will I be able to get the maximum through put??
I have not considered 6500 due to budget. If I consider 6500 will it be a good design to have 6500?s on both core and distribution layer

Switch for String

Hi,
I need to do a switch for a String and not an int.
ex:
switch(String temp=e.getTagName().trim())
case HEADER:
Any idea?
Thanks
Cecile

You cannot. Java only lets you use switch on int or char.
Sorry, but only the if else will do here

I'm switching from PC to Mac. I'm using my one time switch for Lightroom. I have elements 7. Can I upgrade or do I née to just buy outright?

I'm switching from PC to Mac. I'm using my one time switch for Lightroom. I have elements 7. Can I upgrade or do I née to just buy outright?

If you use the organizer, you need to buy the boxed version of PSE 12. You can usually find it at big box stores and online retailers for less than adobe's upgrade price, if you shop around. You need the boxed version because you get a serial number that works on both platforms, and you will need to install PSE 12 in windows first, upgrade your catalog, then make a full backup to a removable drive and restore from that to the mac, after installing PSE 12 there.
If you don't use organizer, it doesn't matter.

Somehow my iPad got switched for messaging to showing from my email. There is no option showing to use my phone number. How do I get it back to my phone number? This happened when I upgraded my iPhone today, but it is using the phone number fine.

Somehow my iPad got switched for messaging to showing from my email. There is no option showing to use my phone number. How do I get it back to my phone number? This happened when I upgraded my iPhone today, but the iPhone messaging is using the phone number fine. It's only the iPad messaging that is messed up. Help, pls.
thanks!

You can link the phone number to the iPad again, if you follow the instructions here.
iOS 6 and OS X Mountain Lion: Link your phone number and Apple ...
The relevant information for you will be at the end of the article. You may have to sign out of messages on the iPhone and the iPad and start all over again.

How to create a standby site for Oracle BISE1

Hi,
I want to build a standby site for my BISE1 site. The primary requirement is that in case of a disaster, when the primary site will be down, the standby site can continue providing the services.
I can build STDBY database for the primary warehouse database, but I do not know how to proceed with the other files of BI system.
Please help me with some articles what Oracle offers for this purpose.
Thank you.

Hi Amit,
If you are planning to setup DR Portal at a remote location, federated portal or Data Replication Tools at DB or Storage Level can be used.
Also A Standalone Portal with a well defined Change Management (UME Data, Portal content Items such as pages, roles, KM content with km exchange) can be implemented.
If both servers will reside at sam location, Clustering may be an option.

Standby Switch for 6509

Similar Messages

Maybe you are looking for