Star Key 3.0 max current

Hi there,
Does anyone know what the maximum current of the Star Key 3.0 is? I'll be needing to use it on an extremely low power system (5V 3A) and need to verify power consumption on any components I use on it.

Quote from: badboy2k on 16-November-12, 13:18:56
MSI Star Key 3.0
Power Consumption from 5V input:
Tx Typical: 128mA (.128A)
Rx Typical: 68mA (.068A)
Standby Mode: 52mA (.052A)
That's it! Thanks so much! :-D

Similar Messages

MSI Star key 3x fatser, license does not include device !!!

Dears,
I have my MSI star key bluetooth device from 1.5 years, it was working perfect on my windows XP SP2. Then I had some problems with my windows, and I wanted to re-install again the driver (after de-installing the current driver) but I found myself getting the following message, when I try to start the bluetooth device:
"your bluetooth software license does not include use with this bluetooth device. [6]", and when I point out to my CD for the license file, I get this message "Bluetooth software license file not found. [2]".
I have tried the driver coming with the device CD WIDCOMM version 4.0.1.2101 and was working for more than 1 year, and also I have tried the new driver on http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=131&prod_no=101 WIDCOMM version 4.0.1.2900 several times with lots of combination and nothing is working, the bluetooth is still red and refuse to start.
I found the same issue is posted too much over the web regarding the WIDCOMM software in general and solution with something as patch I could not find.
I checked the fixed posting on this forum, but it seems all included URLs in the posting are not working.
It seems that contacting MSI support is a waste of time. Could anyone provide guidance or help for me.
Thanks in advance

Quote
It seems that contacting MSI support is a waste of time.
Have you even tried? Visit http://ocss.msi.com.tw, enter your email address and open a new ticket.

N6700 query max current is timing out

I have the N6700 chassis and have installed the IVI driver for it. I have two different modules in the chassis. Both exhibit the same issue. I initialize them, which works fine. I disable the outputs, and then query the max voltage level. All this works and retunrs good data. Then I try tyo query the max current. I have tried with both the IVI function as well as the driver specific function. Both timeout. I have tried passing 0V, 20V, and the output from the max voltage back into its voltage input. It doesn't like the 0V, the other two options just timeout. I use this same routine to querya couple E363x supplies and it works fine on them. Any thoughts on why this specific VI isn't working?
Solved!
Go to Solution.

Does the instrument have any errors after the timeout? Make sure you do a querry for all of the errors from the instrument. That will usually key you into the problem.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions

Registration and MSI Drivers for MSI STAR KEY 3

First of all for some strange reason i cannot register my star key 3 which i bought at 23/03/2010 from www.e-shop.gr, i have send to MSI the photo with the serial number.Second, clearly in the manual refers about a software driver CD which was not included in my package! I have searched the MSI site for an MSI driver and it has only for STAR KEY 1 and 2 ,not for STAR KEY 3! Currently i have the driver that Windows XP service pack 3 installed but as i saw from previous models STAR KEY 1 and 2 ,the MSI driver has more features.To anyone who has MSI STAR KEY 3, did MSI included a driver CD in the package?

Even though I can understand your frustration, you need to understand a few things in order to take the next steps in this matter:
First:
The BlueSoleil package is not an MSI Product but a piece of bundled third party software that comes with the package. It is kind of like buying a CD/DVD Burner and getting a CD that contains Nero Burning ROM and a valid license for the particular Nero Version on that CD. Now let's say: That this "older" Nero Version does not work very well with Windows 7 64bit (because it was concipated for older Windows Versions). Who do you blame for that? The manufacturer of the optical drive? When you contact the software company behind Nero about that, they will tell you exactly the same thing as BlueSoleil did: Buy a newer version! Now, please don't tell me, that will start complaining about the manufacturer of the optical drive about an outdated Nero Version.
Second:
Quote
I bought this device a couple of months ago, so its not even a very old one!
Just because you bought this device only recently in some shop, that does not mean that it is brand new (the shop could have had that thing in stock for a couple of years already).
In fact, the device is at least 3 years old (if not older) and is officially advertised as supporting the 32bit versions of Windows 2000, Windows XP and even Windows Vista. Windows 7 was not even on the market back then and therefore there was also no possibility of including a copy and a license for a Windows 7-ready Bluesoleil version. There is an old version of the bundled/third party BlueSoleil Software on there because the product was put out on the market more than three years ago. In case the people in that shop you bought the device in told you any different, they did not really provide very good advice.
Quote
the ability to contact the real MSI Support
... exists here: http://support.msi.com/
However, MSI will most probably be able to help you with getting your hands on a free up-to-date Bluesoleil version (just like the optical drive manufacturer who will not provide you with a free copy/license of the latest Nero Release).
Quote
I also tried to register the product but the registration page says: "not MSI product" BAHH!!! WHYY??
What page exactly? Do you have a link?
Quote
I have the serial number
Did you enter the serial number of the device or the serial number for the BlueSoleil Software Version that came with it?

Key figure comparision between current year and previous year

Hello collegues,
I have created a WEB Intelligence report with key figure ROI (return on investment which is calculated out of three other key figures (capital, revenue and costs). I would now like to calculate the percentage period (year) differences between key figure ROI - between current year (month) and previous year (month).
Do I have to add coding within a key figure formula within WEBI Rich Tech client or within universe builder.
The key figures were extracted from SAP BW and added to a universe which is basis for WEBI rich tech client report.
thanks and regards,
Christian

Hi Stratos,
so I see - i have to use the variable Editor and then define a measure and add coding in the formula field. Do you have an e-mail address ín order to send you the report and explain in more detail what I would like to see - here it is not possible to upload a report...
thanks and regards,
Christian

Key value does not currently exist in the primary key table error

Im testing out a form and creating a new insert once all the fields are filled in it wont allow me to move on and comes up with this error message;
key value does not currently exist in the primary key table
Is this becuase the form contains foriegn keys which reference different tables which fields are not dispalyed on this form?
If so how to I link the other forms together so that when i create a new record in this form it will automaticaly create the primary key entry in the other form to allow the insert of the referenced foreign key in this form?
does this make sense?

It seems that it has the table in which you'r inserting is a foreign key table.
Take the emp& dept table example in the schema scott/tiger.
Say we have deptno 10, 20, 30, 40 in the dept table.
We make a form for emp table and insert into this form.
Now, we'r bound to insert deptno 10, 20, 30, 40 into this emp form. This form will not allow us to insert deptno 50 as it doesn't exist in the primary key column in dept table.
Obviously if a department doesn't exist in the company, it doesn't make sense to assign the employees to that department.
So for this purpose, we need to add a department in the dept table then we can insert values in the emp table for that department.
For this purpose, I suggest to make a button on the mp form and invoke the dept form and add a new department to it and then insert into emp table.
The same scenario can be applied in your case.

Does the max current flow of scxi-1163R channel only 200mA?

I want to use scxi-1163R and scxi-1326 to control the ASCO solenoid valves(water control).
The input voltage/current of valve is 24VDC/500mA.
But the max current of scxi-1163R is just 200mA. Does it mean that i can not directly connecting the valve to module?
Is there any other solutions?

Hi Hau,
I am assuming that you have an external power supply connected to the valves and that you want to use the SCXI-1163R to open/close the circuit. As you stated, the SCXI-1163R has a max current rating of 200mA. Unfortunately, going above the max current rating could damage the relay. However, National Instruments does offer SCXI switches that are capable of handling the current and voltage ratings that you have specified. See the following link (page 4 of the PDF document) for a list of the switches that National Instruments offers.
Have a great day!
Brooks W.
National Instruments

NI PXI-2564 115Vac 400Hz max current 4 amps

Can the NI PXI-2564 handle 115Vac 400Hz max current 4 amps?

RFB-AIS,
My apologies, on further examination, it turns out you should be all set. The maximum relay operate time is not actually associated with the frequency of your signal. The important characteristics are the switching current and voltage, and combined power, which a"must not exceed 30 W at 150 VDC, 150 W at 30 VDC, or 150 VAC, 5 A" according to the product manual--http://www.ni.com/pdf/manuals/373963h.pdf
All of your signal characteristics satisfy those requirements, and you shouldn't have any issues operating at 400 Hz.

CFP-AO-200 only puts out max current level 4.3mA

cFP-AO-200 only puts out max current level 4.3mA using fieldpoint explorer. The load is 350 ohms resistor.
Brad Whaley
LabVIEW Certified Engineer

What is the voltage level of the external power supply you are using? The FP-AO-200 and cFP-AO-200 output load drive capability is based upon the voltage of the external supply that you are using. They each have an internal 3 volt drop. You can use V=I*R to determine the load drive capability. For example, with a 5 volt external supply, you have the 3 volt drop, so 2 Volts/ 21 mA = 95 Ohm load maximum. With a 24 V supply, you can drive the maximum rated load of 1000 Ohms. For a 350 Ohm load, you will need a minimum of a 10.5 Volt supply.
Regards,
Aaron

MSI Star Key on Windows 7

Hello!
I have a bluetooth usb device since 2005, back then I used to have windows xp and it worked very well, now I have win7 32 bits and I'm having troubles with the installation, driver is not supported.
The device is the MSI star key v 1.0. How can I get the right drivers??
Regards!

Topic split and renamed.
This is a very old device now, and MSI does not provide Windows 7 drivers.
Its possible that drivers are already included with Windows 7, have you tried letting Windows Update find drivers for you?
Alternatively you could give the Vista 32bit drivers a try, they may just work (Windows XP drivers won't):
http://eu.msi.com/product/net/STAR-KEY.html#/?div=Driver&os=Vista%2032

Star Key 2.0 trouble

(Tried to reach customer support over the phone. They put me on hold for about 30 mins. and afterwards I got an answering machine. Way to go MSI! Tried submitting my support request via the MSI website. After half an hour of filling out the damned form in all the details, click submit and get some website error. Way to go MSI!)
Anyway, I bought a Star Key 2.0 dongle to listen to music in stereo with my new Jabra stereo headphones. Only trouble so far! Let me start with one isue, particularly disturbing. After connecting the Jabra headphones to the dongle/computer, the default Audio device in Windows' "Sounds and Audio Device Properties" does not automatically switch to Bluetooth High Quality Audio, so I have to do this manually all the time. There are also other problems, but so far I'd appreciate some help in order to solve this one.

Quote from: Tiresmoke on 20-September-06, 19:19:50
So if I had to guess the key and the headset may not be fully compatible.
Well, as I was saying, I have tried the dongle with three bleeding edge stereo headsets from three top of the line companies (among them Jabra and Plantronics). Doesn't get any better than that, trust me. It would be really weird for a commercial Bluetooth dongle to be incompatible with that.Quote
There may be something else but the USB2.0 does not seem to be mentioned in the manual at all. You may want to ask the tech if he has ever seen this device himself or ask if he is guessing. Then ask for a tech to respond that has used the device.
Yep, they say they tried it with their own MSI FS300 stereo headset and it works fine. (Yeah, what else could they say, right?) Now, everybody seems to be missing the point that I came across precisely the same issues with my Belkin dongle, and they were solved after I installed some obscure patch I found on Belkin's website (no thanks to Belkin tech support though!). It's gotta be that this is also fixable via some firmware update. I do not think this is a hardware issue. At any rate, they told me that there is no such firmware update available, nor is there any in the works. Also, interestingly enough, they say they can only test the dongle with their own headset. My thinking is that anyone that claims compatibility with a standard as widespread like Bluetooth, should do everything possible to ensure that their device works indeed with other Bluetooth-compatible devices.Quote
I haven't so this is all the help I can be.
Thanks for the replies though. My only hope is that others will come across the same issues with this dongle. Until then, I will most likely be springing for a Jabra dongle: that one, at least, should work with their own headset.

Star Key 2.0 Bluetooth dongle crashes Autodesk Maya?

After pairing my Star Key 2.0 Bluetooth dongle to my Nokia phone, I was no longer able to launch Autodesk Maya 8.5 (running on Vista 64-bit edition). Maya quits immediately after it finishes loading. If I remove my phone from the list of Bluetooth devices in my Bluetooth settings, Maya loads without any problems.
I'm not sure if this is a problem with the Star Key dongle or with my Nokia phone (it's the only Bluetooth device I own, so I can't test this with another Bluetooth device) or with Bluetooth in general, but I wanted to post this information in case anyone else was having a similar problem. I am using the Star Key dongle with the latest MSI drivers (not the Vista drivers). It's possible that this is not an issue if you use the default Vista bluetooth drivers... I'm not sure, as I haven't tested it.
Let me know if you are experiencing any similar problems.

Dongles are allways a pain in the but.
They are a copy-protection and they are known to give troubles in combination with other devices.
Try under XP, it can be well a Vista problem too.

MSI Star Key 2.0 & Windows XP x64

Hi,
I have Star Key 2.0 and it's working fine with Windows XP x64. I'm using Microsoft's Bluetooth Stack and it's not supporting Headset profile for example. I can use Widcomm stack with my dongle when using Windows XP, 32-bit version, am I right? Is it possible to use Widcomm stack with x64?
- Matti P

Ok. I found 64-bit Widcomm stack (5.0.1.2500). I installed it, but it won't work with my dongle. Stack tells me the following message "Your Bluetooth software license does not include use with this Bluetooth device.[6]". So, I tried to use license file which is located install CD and got the following message "You cannot install an older version of Bluetooth Software over a newer version of Bluetooth Software. [-349]" I suppose that the license file is for Widcomm 4.0 stack, and it is not working with the 5.0 stack. I did a fast search and did not find 64-bit version of the 4.0 stack.

Msi star key 2.0

I have bluetooth dongle MSI Star Key 2.0 with original Widcomm drivers. By which functions and how can I find devices in range of dongle and connect to it by using this driver through SPP prifile. I am creating my aplication in Visual C++. Can anybody help me with this?

Quote from: tempaccount1234 on 05-April-11, 19:27:06
Could anyone please provide specific information? Will the Vista drivers work for Windows 7. I am not able to use them. Is there any setting required? Please help......
No Vista drivers often do not work in W7.
You better buy a new device that has W7 drivers.

Msi star key 2.0 3x faster wireless network adapter with windows 7

Hi,
I have msi star key 2.0 3x faster wireless network adapter product. Could anyone please provide me information whether it is compatible with both 32-bit and 64-bit Windows 7 operating system? Thanks in advance.

Quote from: tempaccount1234 on 05-April-11, 19:27:06
Could anyone please provide specific information? Will the Vista drivers work for Windows 7. I am not able to use them. Is there any setting required? Please help......
No Vista drivers often do not work in W7.
You better buy a new device that has W7 drivers.

Star Key 3.0 max current

Similar Messages

Maybe you are looking for