Start booting then reboot

Hi
i've just installed WinXp + update
other software are installed (office, nero, steam, sandra, ....)
when i start the PC, winxp is booting, and when loading logo & blue bar, winxp reboots and start correctly.
why ?
Thanks

mm! very simple just try to press f8 and go to safe mode or last good config   if your pc boots it could be a driver problem, so remove it
if not try to test you bios config reset to bios normal defaults and then test your ram pci cards so on.

Similar Messages

  • How can i get my imac proceed to home page from restarting endlessly?  it will start then start booting then chime then bck to step one, not even hitting the start up page.... plssss help!

    how can i get my imac proceed to home page from restarting endlessly?  it will start then start booting then chime then bck to step one, not even hitting the start up page.... plssss help!

    Hi
    My Powerbook was the same. Only fix is to reinstall OSX from the install CD but be sure not to pick the Format and install clean. Once you boot with the install CD pick the preserve user data and settings.
    On My machine the reinstall looked perfect. My network, email, files and all the programmes were all there. Most apps worked fine but Adobe CS2, Virtual PC and NetBarrier all needed reinastallation as they reported a few files or registration was missing. I went for the 10.4.3 upgrade again and it worked fine.
    Good luck
    D

  • Phone starts booting then aborts

    I have just updated my iPhone OS to 3.0 release, after having been using the dev beta. I now find my phone start booting (shows the Apple logo) and then after a few seconds aborts and turns off. I have tried connecting it to the computer, to the wall adaptor, leaving it for a while, but nothing seems to make a difference.
    Any idea on what I should be trying to do?

    Looks like I should have searched before posting. Looks like there is recovery mode:
    http://support.apple.com/kb/HT1808

  • IMac starts boot then cuts off

    My iMac was working fine.  I got a message that the memory was almost full then it just cut off.  Now when I try to turn it on, it goes to the white screen, The booting bar comes up, but as it starts to boot, everything just cuts off.

    You may have totally filled your internal HD adn need to move libraries such as you iTunes, iPhoto or iMovie libraries to an external HD. Please attempt to boot into Safe Mode by holding down the Shift key when you hear the startup tone until a progress bar appears. If you can do that then move those libraries to an external HD and then attempt to restart.

  • Just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now

    just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now

    I am assuming the phone was working prior to you installing IOS 6? Did you use itunes to install IOS 6 or just run from the phone?
    When I tried to do the Over The Air update to IOS6 on my iPhone 4, it errored out and I had to connect it to iTunes and select "Restore" from the summary screen after iTunes finds the phone is connected. If this works for you, it will go through a couple of reboots that take a few minutes to complete. It should then give you the option to start with a fresh new phone or to use one of your previous backups to load your contacts and other information, provided you have backed up the phone previously.
    I hope this helps you my friend!

  • My Macbook Pro will not boot up. I can hear the sound that it has started and then goes into an infinite loop.

    My Macbook Pro will not boot up. I can hear the sound that it has started and then it goes into an infinite loop.

    What model MBP and which version of OS X? Sounds as if the hard drive may have failed. If you have an installation disc, try booting with it. If your machine came with Lion or Mountain Lion, try booting to the Recovery partition - Command and R keys held down while booting.
    Clinton

  • I started Boot Camp on a MAC mini but then  had a power failure after 30 secs :( Now when I start Boot Camp the option to install Windows 7 is gone.  In it's place is Remove Windows 7.  It seems to hang at Partitioning disk  Can I recover?

    I started Boot Camp on a MAC mini but then  had a power failure after 30 secs Now when I start Boot Camp the option to install Windows 7 is gone.  In it's place is Remove Windows 7.  It seems to hang at Partitioning disk  How can I recover?

    Welcome to the Apple Support Communities
    That's because the Boot Camp volume was created, but your Mac hasn't been set up to start automatically from the Windows disc. Insert the Windows DVD and press C key while your Mac is starting to start Windows installation.
    If you want to make sure that everything is correct, open Boot Camp Assistant and choose the option to remove Windows 7. Then, open that application again, select the option to install Windows 7 and you will be able to install Windows as usual

  • MS-6743G (865GM2-LS) System Start & get boot then Auto-off, Unable to find prblm

    Hi,
    I have problem with my computer to start
    MS-6743G (865GM2-LS) System Start & get boot then Auto-off,
    every time start, the system boot, after Bios load, then turn-off
    If press Del key, enter BIOS setup, also turn-off power
    How to solve this problem, what is the problem?
    Is't the motherboard problem?
    Processor problem?
    I can't find it?
    Please anyone help me to solve this problem?
    Thanks
    PC Sekar

    Hi
    This is the specifications for my System
    MSI 865GM2-LS(MS-6743G), Intel P4 2.80E 800MHz 1MB CPU
    XP Pro w/SP2 all updates
    Kingston KVR266X64C25/256
    (512MB-64Mx64 DIMM, PC3200-DDR SDRAM -Exchanged the above one)
    SAMSUNG CD-RW Driver SH-R522
    Maxtor 120GB (6Y120M0STD) SATA, DiamondMax Plus 9
    MITSUMI 1.44 Disk Drive, Model D359M3
    HP7540 17" monitor
    Please check it & help

  • Download starts but then stops...

    So I've read other forums and searched this website for one, but I still can't find the answer. Whenever I try to download the file it will start but then after some time get stuck on a percentage(different every time) and then stop all together. I've tried using different browsers and a download manager, I have plenty of storage space also. It still won't work
    I've heard that this may have something to do with my internet and secruity? Or something? Can someone tell me how to fix that? My technical skills are very very low and this is the first time I've used a mac.

    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. For instructions, launch the System Preferences application, select Help from the menu bar, and enter “Set up a guest account” (without the quotes) in the search box. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem(s)?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault in OS X 10.7 or later, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
    Be sure your Mac is shut down.
    Press the power button.
    Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
    Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    *Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, you can’t boot in safe mode.
    Test while in safe mode. Same problem(s)?
    After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

  • Satellite P100 shuts down then reboots

    G'day, my laptop boots up fine and then after some time, a couple of minutes to a couple of hours, it will instantly die with no warning, then reboot as though it was a fresh start. There are no errors captured.
    I've had the system checked, wiped the hdd, changed the hdd and mem, I'm runnimg XP pro.
    it's on now in bios ok, but when in windows it will shut and restart. I don't think that temp is an issue because of the restarts at 4mins. 3yrs running fine, then this.
    Any ideas???
    Neil

    Hi njgo2,
    If you have already reinstalled Windows, it shouldnt be a software or driver issue. Theoretically it could be shut down due a higher internal temperature. Your notebook is 3 years old so have you already cleaned it? If not its time for that because a notebook should be cleaned every 3-4 months. If you use compressed air spray, you will wonder how much dust comes out. ;)
    So before you change anything, clean it firstly. It takes only few minutes and therefore its not necessary to disassemble it.

  • X301 Cold boot always reboots?

    Hi,
    Every time I cold boot my laptop it runs through POST, then reboots and POSTs again, then starts the OS.
    It's a minor issue, but rather anoying, i.e. with fingerprint reading as you need to swipe twice.
    This problem only occurs from a cold boot. When restarting the laptop this issue doesn't appear.
    Anyone else have this problem?
    thanks.

    And yet another bump. Lenovo, can you please tell me what to do about this? This is the THIRD box already with various issues. Love the form factor but would like to have a completely working one...
    Florian

  • MSExchangeSA and IS is not starting automatic at reboot after upgrading the server from SP1 to SP2

    I am running a 2 node DAG with separate Hub & CAS servers
    I have already upgraded the Hub CAS server and they are fine
    Exchange running on Windows 2008 R2 SP1
    All are in VM-Ware ESXi 5.0
    After I upgrade the mailbox server to SP2 the SA and IS service not starting automatic after reboot
    If I run "net time /set" command and then restart ADtopology server, the IS and SA starts fine
    But again after reboot they do not start
    Also I get the below event in the app log when the IS & SA fails to start
    Log Name:      Application
    Source:        MSExchangeIS
    Date:          05/22/2012 5:15:03 AM
    Event ID:      5003
    Task Category: General
    Level:         Error
    Keywords:      Classic
    User:          N/A
    Computer:      server.domain.com
    Description:
    Unable to initialize the Information Store service because the clocks on the client and server are skewed. This may be caused by a time change either on the client or on the server, and may require a restart of that computer. Verify that your domain is correctly
    configured and  is currently online.
    If I check the Registry for time resource it is taking from the DC
    I manually compared the time between DC and Exchange and it is fine
    Since the Exchange mailbox is virtual, I checked the time sync on VM-Ware tools and it is "unchecked"
    Checked for group policy and do not find any specific to time sync.
    Confirmed that Windows Time service is running
    Suspecting a Operating system issue, tried to upgrade the other DAG
    Even that node is displaying the same symptom and Issues
    Tried to install RU1 on both nodes and that too did not fix the issue.
    Checked with VM-Ware engineer and he said that every thing from VM-Ware end is fine
    Is Anyone have come across the issue before ?

    Exchange 2010: Unable to initialize the Information Store
    Problem: 
    Unable to initialize the Information Store service because  the clocks on the client and server are skewed.   This may be caused by a time change either in the client or the server,  and may require a reboot of that computer.   Verify that
    your domain is properly configured and  is currently online.
    Solution: 
    Open a cmd prompt from the Exchange Server as administrator (right mouse click on the command prompt shortcut and select “Run as Administrator”)
    Run this command
    Net time \\ADServerName /Set
    Restart the Microsoft Exchange Active Directory Topology Service
    *Important!! You have to restart the Microsoft Exchange Active Directory Topology Service or this fix will not work..  I tried just starting the Information Store service after running the command it it still failed..
    This worked for me and all is well on my exchange server.
    - See more at: http://www.mountainvistatech.com/2012/06/04/exchange-2010-unable-to-initialize-the-information-store/#sthash.SwQpgQEM.dpuf

  • Ias-component doesn't start after linux reboot

    Hi,
    i've successfully installed the oracle infrastructure. it's all working until i reboot my rhes3 server, all the opmnctl ias-component are stopped/NONE and did not start automatically.
    how can i configure the oracle infrastructure to start automatically after reboot?
    dcm-daemon, oid, oc4j were all stopped and i couldn't restart it either.
    thanks.

    In my opinion, it is better to manage the starting and stopping of all Oracle services yourself - rather than leaving it to the OS to do this for you - there are many reasons for this......for instance - if you are running on a split tier configuration, and there is something wrong with the listener for your repository, then the mid tiers will not come up until the repository is up - and so on and so forth....
    I have one script that calls three scripts that check, stops or start all oracle services. I have the OID and portal tiers on one server - the start script is given below - and the stop and check scripts are all variations of this start script. Hope this helps.
    #!/bin/bash
    # - DATE
    # This scripts starts all Oracle Services on SERVER_NAME
    # Start the EM console on SERVER_NAME - Infra (Mid) Tier
    echo "Starting the EM Console on the Infra Tier"
    /u01/app/oracle/product/OAS/10.1.2/infra/bin/emctl start iasconsole
    /u01/app/oracle/product/OAS/10.1.2/infra/bin/emctl status iasconsole
    # Start EM Console on SERVER_NAME - Portal (Mid) Tier
    echo "Starting the EM Console on the Portal (Mid) Tier"
    /u02/app/oracle/product/OAS/10.1.2/portal/bin/emctl start iasconsole
    /u02/app/oracle/product/OAS/10.1.2/portal/bin/emctl status iasconsole
    # Start Services on the Infrastructure tier - including OID, HTTP Server
    # and OC4J_SECURITY
    echo "Starting Oracle Services on the Infrastructure Tier"
    /u01/app/oracle/product/OAS/10.1.2/infra/opmn/bin/opmnctl startall
    echo "Status of Oracle Services on the Infrastructure Tier"
    /u01/app/oracle/product/OAS/10.1.2/infra/opmn/bin/opmnctl status
    # Start Services on the Portal (Mid) tier - including Portal, OC4J_Portal,
    # Forms, Discoverer and OC4J_SECURITY
    echo "Starting Oracle Services on the Portal (Mid) Tier"
    /u02/app/oracle/product/OAS/10.1.2/portal/opmn/bin/opmnctl startall
    echo "Status of Oracle Services on the Portal (Mid) Tier"
    /u02/app/oracle/product/OAS/10.1.2/portal/opmn/bin/opmnctl status

  • When power on and start up my computer start and then power off

    Hello
    When power on and start up my computer start and then power off

    whether you hear Mac Boot sound?
    if not may be your Harddisk is failed to start

  • Analysis Services started and then stopped, Event ID: 0xC1210000

    I just installed SQL Server 2005 Developer Edition and SP1 and SP2. I cannot start Analysis Services.  The message box states: The SQL Server Analysis Services (MSSQLSERVER) service on Local Computer started and then stopped.     I looked in the log files located at: C:\Program Files\Microsoft SQL Server\MSSQL.2\OLAP\Log and found these entries:
    msmdsrv.log:
    (6/15/2007 10:07:34 AM)
    Message: The service cannot be started: 
    (Source: \\?\C:\Program Files\Microsoft SQL Server\MSSQL.2\OLAP\Log\msmdsrv.log,
    Type: 3, Category: 289, Event ID: 0xC1210000)
    (6/15/2007 10:10:26 AM) Message:
    The service cannot be started: 
    (Source: \\?\C:\Program Files\Microsoft SQL Server\MSSQL.2\OLAP\Log\msmdsrv.log,
    Type: 3, Category: 289, Event ID: 0xC1210000)
    During installation I did get an unhandled exception (I don't know what component caused the exception). I have found this in the SQLDUMPER_ERRORLOG.log file:
    06/14/07 17:39:38, ERROR ,               msmdsrv.exe, Unable to open file C:\Program Files\Microsoft SQL Server\MSSQL.2\OLAP\Data\FlightRecorderCurrent.trc, error 2
    06/14/07 17:39:38, ACTION,               msmdsrv.exe, Watson Invoke: No
    Any ideas how to get this service started?

    Does anyone have any idea on this problem?  My installation of SQL Server Analysis Services worked fine.  I now have the same error as Lucy.  This happened after no upgrading of SQLSERVER.  It must have issues with security patches on the OS, or maybe service packs for Visual Studio (2005).  And no reinstallation of the patch is not the answer (or rebooting).
    The service times out and tells me to check the logs.  The msmdsrv.log file indicates any unhandled exception -
    Message: The service cannot be started: Internal error: An unexpected exception occured. (Source: \\?\C:\Program Files\Microsoft SQL Server\MSSQL.1\OLAP\Log\msmdsrv.log, Type: 3, Category: 289, Event ID: 0xC1210000)
    Message: Service stopped. (Source: \\?\C:\Program Files\Microsoft SQL Server\MSSQL.1\OLAP\Log\msmdsrv.log, Type: 1, Category: 289, Event ID: 0x41210001)
    Message:  (Source: \\?\C:\Program Files\Microsoft SQL Server\MSSQL.1\OLAP\Log\msmdsrv.log, Type: 3, Category: 256, Event ID: 0xC1000016)
    I have tried reinstalling, changed users for the service, changes instance names.  The logging tells me nothing, except there is a big problem.
    I even installed the SQL Server SP2 hoping to fix whatever the problem was.  Now I also have SSIS throwing an exception and wanting to attach a debugger to it on top of my original problem. After reading about all of the problems with SQL Server SP2, I think I created a bigger monster.  Uninstalling leaves around all kind of files, registry entries, and program numbers.
    Thanks for ANY hints to proceed.

Maybe you are looking for