Start studying on Mobility Services Engine

Hi all,
I have assigned to characterize MSE which could be used for a future project.
After a quick research, I know that I need to setup at least a basic topology including
1. A virtual machine of MSE : MSE-VA-7-5-102-101-LowEnd.ova
2. A virttual machine of PI : PI-VA-1.4.0.45-small.ova
3. A virtual machine of WLC : AIR-CTVM-7-5-102-0.ova
I also have already ordered 4 Aironet 3600 APs.
However, it requires to have service contracts linked to my CCO to be able to download those softwares.
As a newbie, I don't know how can I get those required service contracts. So could anybody guide me on this one ?
BTW, because the tight schedule of the study, could somebody send me those softwares so that I can finish my task on time.?
Thanks,
Regards,
Toan.

Hi Steve,
We are already Cisco partner and still cannot download the software, it requires valid linked contract services.
I aslo contact some of our local partners but not yet received any reply.
As time bugdet for me is too short, it's great if I can get the software from you guys in this forum.
Toan.

Similar Messages

Mobility Service Engine 7.4.100.0 ova WEB Services problem

Hello,
We have sucessfully installed MSE-VA-7-4-100-0.ova file in our Lab, and after installation we can't open https session with MSE.
When we type <https://mymseipaddress> we are getting these message:
Error 404 - Not Found.
No service matched or handled this request.
Known services are:
http://my server:8880/hs/
http://my server:8880/mdp/
http://my server:8880/admin/
http://my server:8880/wips/
http://my server:8880/location/
http://my server:8880/subscription/
http://my server:8880/aaa/
http://127.0.0.1:8180/localadmin/
https://127.0.0.1:8443/localadmin/
https://my server:8843/mdp/
https://my server:8843/wips/
https://my server:8843/hs/
https://my server:8843/admin/
https://my server:8843/location/
https://my server:8843/subscription/
https://my server:8843/aaa/
We are able to import MSE to Cisco Prime Infrastructure 1.3 and we have communication with WLC. We have tried proposed solution explained in link below:
https://supportforums.cisco.com/message/3656441#3656441
but we are are unable to import server certificate becouse our certificate vallidation is falling. We don't know how we should append private key to the signed certificate in order to get our MSE web services up and running.
Any help in solving this problem would be much appreciated.
Regards,
Jelena

Here is the output from getserverinfo:
[root@MDS-MSE-LAB ~]# getserverinfo
Health Monitor is running
Starting MSE Platform, Waiting to check the status.
MSE services are up, getting the status
Server Config
Product name: Cisco Mobility Service Engine
Version: 7.4.100.0
Health Monitor Ip Address: 1.1.1.1
High Availability Role: 1
Hw Version: V01
Hw Product Identifier: AIR-MSE-VA-K9
Hw Serial Number: MDS-MSE-LAB.mds.rs_3287d770-825b-11e2-8bd8-00505692612a
Use HTTP: false
Legacy HTTPS: false
Legacy Port: 8001
Log Modules: -1
Log Level: INFO
Days to keep events: 2
Session timeout in mins: 30
DB backup in days: 2
Services
Service Name: Context Aware Service
Service Version: 7.4.0.38
Admin Status: Enabled
Operation Status: Up
Service Name: WIPS
Service Version: 1.0.4041.0
Admin Status: Disabled
Operation Status: Down
Service Name: Mobile Concierge Service
Service Version: 2.0.0.37
Admin Status: Enabled
Operation Status: Up
Service Name: Location Analytics Service
Service Version: 1.0.0.12
Admin Status: Enabled
Operation Status: Up
Server Monitor
Server start time: Fri Mar 01 15:59:43 CET 2013
Server current time: Mon Mar 04 09:39:45 CET 2013
Server timezone: Europe/Ljubljana
Server timezone offset: 3600000
Restarts: 6
Used Memory (bytes): 66655704
Allocated Memory (bytes): 133169152
Max Memory (bytes): 477233152
DB virtual memory (kbytes): 0
DB virtual memory limit (bytes): 0
DB disk memory (bytes): 2137466496
DB free size (kbytes): 0
Active Sessions
Session ID: 16978
Session User ID: 1
Session IP Address: 10.13.7.15
Session start time: Mon Mar 04 09:38:17 CET 2013
Session last access time: Mon Mar 04 09:38:19 CET 2013
Default Trap Destinations
Trap Destination - 1
IP Address: 10.13.7.5
Last Updated: Fri Mar 01 11:43:04 CET 2013
Context Aware Service
Total Active Elements(Wireless Clients, Tags, Rogue APs, Rogue Clients, Interferers, Wired Clients): 25
Active Wireless Clients: 13
Active Tags: 0
Active Rogue APs: 11
Active Rogue Clients: 1
Active Interferers: 0
Active Wired Clients: 0
Active Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients, Tags) Limit: 100
Active Sessions: 1
Wireless Clients Not Tracked due to the limiting: 0
Tags Not Tracked due to the limiting: 0
Rogue APs Not Tracked due to the limiting: 0
Rogue Clients Not Tracked due to the limiting: 0
Interferers Not Tracked due to the limiting: 0
Wired Clients Not Tracked due to the limiting: 0
Total Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients) Not Tracked due to the limiting: 0
Context Aware Sub Services
Subservice Name: Aeroscout Tag Engine
Admin Status: Disabled
Operation Status: Down
Subservice Name: Cisco Tag Engine
Admin Status: Enabled
Operation Status: Up
Regards,
Jelena

How do I start my Apple Mobile Service?

I hooked my iPhone 3GS into my school computer and normally, it begins to sync up and I am able to play music from my phone but for some reason I am unable to do this now and it tells me that I need to start my Apple Mobile Service. Help!!!

For a PC
For a Mac

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

ISE ( Idendity Service Engine ) & MSE (Mobility Service Engine ) & Prime Infra

What is the difference between ISE ( Idendity Service Engine ) & MSE (Mobility Service Engine ) & Prime Infra .
How this will be used along with WLC & AP & wireless Users.

The Cisco Identity Services Engine (ISE) is an all-in-one enterprise policy control product that enables comprehensive secure wired, wireless, and VPN access, leading to more productive workers and lower operations costs. When operating in a network, ISE provides the following key features: 1.Rigorous identity enforcement 2. Extensive policy enforcement 3.
Security compliance 4. Automated onboarding whereas Cisco Mobility Services Engine supports RTLS and WIPS and Cisco Prime is centralize wireless and wired Monitoring and management solution. ISE and MSE both can be integrated with Cisco Prime. For more deatil over these products you can see the below links.
http://www.cisco.com/en/US/prod/netmgtsw/prime.html
http://www.cisco.com/en/US/prod/collateral/wireless/ps9733/ps9742/data_sheet_c78-475378.html
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5712/ps11637/ps11195/data_sheet_c78-656174.html

TS1567 its denied, it says that "windows could not start the apple mobile service on Local Computer"?

its denied, it says that "windows could not start the apple mobile service on Local Computer"? What do I have to do?

http://support.apple.com/kb/TS1567

Mobility Service Enginer & WCS required or not?

Hi,
I have Cisco Wireless Lan Controller 5508 with 35 (3600 Series Access Points. Do i need to purchase Mobility Service Engine for this or no need? Do i need WCS server for this or no need?
Thanks,

The WCS/NCS/Prime and MSE are optional devices that you don't need to get your wireless up and running. So no, you don't need to purchase those devices unless you want the features those devices will provide you. These features are listed in the data sheet.
Sent from Cisco Technical Support iPhone App

Need some help getting started with Mobility Services Engine

Someone has ordered several 3602 access points, a 5508 controller, and a MSE 3310 for one of our remote locations. The access points and controller are in place and are working fine (we use lightweight APs at many other locations), but I'm not sure how to approach the MSE. I've gone through the set up, and it's onsite, on the network, and I've added it to our WCS server. It's got a 2000 user context-aware services license. But I'm not sure where to go from here. It doesn't seem to actually be doing much of anything. Is there some quick start guide as to where to go from this point? The wireless users are mostly mini netbooks and iPads.

Well, I'm no expert, but I did spend the night...
Ok. In the WCS on the Services tab, Mobility Services, your MSE is recognized and reachable with matching SW Versions.
So, on the home tab, ContextAware tab, you see your MSE and it is showing Zero's for data in most if not all fields?
Back to the Services tab, Synchronize Services... is this empty?
The MSE can only 'SEE' what you tell it to 'LOOK' at. That is, buildings and floor areas. I haven't tried just a building.
Check the left hand box for all the floor areas of interest. Scroll to the bottom an slect 'Change MSE Assignment"
select which (of the many or the one) MSE you wish to have monitor the area. Check the 'CAS' box and save.
Up on the upper levt is a Synchronization block.. push the Synchronize button and sit back..
All MSE data is presented only to the WCS (or Pi).
Good Luck
David

3355 Mobility Service Engine failed to start

Hi,
After I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"
Then I decide to reboot the appliance, after that MSE shows the message "
Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?
import gamin
ImportError: No module named gamin
Sent from Cisco Technical Support Android App

Are you not able to access the cli? If so, try to issue the following:
/etc/init.d/network status <--- check the status
/etc/init.d/network reload <--- if a service isn't running
/opt/mse/setup/setup.sh <--- to review or make changes to what was entered on the setup script.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Install Licence failed on Mobility Service Engine v6

Dear Cisco community,
I have a problem on installing the license for MSE.I use the MSE 3310 for context aware service. I have set up the MSE appliance correctly but i failed to install the device tracking license on WCS.
I use WCS PLUS license on version 6. When i add the lic file, WCS said "error while installing license".
Anybody know what the problem might be? I rechecked the UDI for MSE again, and it is correct. So i assume that it is not related to bad license.
Please any comment are appreciated

I think, I have correctl installed the new user ((charms, Settings, Change pc-Settings, Accounts, Other Accounts, Add an account, username, Password, Password, hint - that's not so difficult (on the first glimpse) - and I'm admin on Win 8.1 Pro.
But maybe I missed a secret secret ?!
No matter, whatever - your suggestion helped me - I can live with it, even though my PC is probably not in order.
(At least until the next time)
No matter, whatever
- this
Suggestion helped
me (Nt Authority\SYSTEM ACCOUNT) -
I can
live with it,
even though
my PC is
probably not
in order.
(At least
until the
next time)
Greetings, Otto
O.F.

Mobility Service Engine without Client or Tag licenses

What does the base MSE box get you when you do not have any additional feature licenses?
Do I still get rogue AP location mapping and history?

An MSE out of the box with no licenses will have a 100 tag/client 60 day evaluation license. After the 60 day you would go back to being able to track one device at a time via the WCS.

Mobility Service Engine back up failed

I have recently installed Cisco MSE and attached it to my Prime infrastructure 2.0 appliance but the MSE backup failed with the following error
MSE Backup failed for mse.xxxx.xxx.xxx.xxx. Reason: null
I can't see any reference to backup errors, has anyone else had a similar issue?

It happens due to compatibility issue between the PI and MSE. What is the MSE version? Check the compatibility from
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Apple mobile service doesn't work

hi,
from some reason when I plug my iphone 6 to my computer, I get this message-"Apple mobile device service could not be started because an unknown error occurred (1058)".and then I get a follow up message-"this iphone cannot be used because the apple mobile device service is not started".
I followed the orders in the website how to start the apple mobile service, but I get this message-"the apple mobile device service on local computer started and then stopped.some services stop automatically if they are not in use by other services or programs".
I tried again and again to start the apple mobile service but it's just stop in the middle and I get this message. I reinstalled itunes twice but it's still doesn't work.
please help me I'm desperate!

Hey oommeerr,
Sorry to hear that you are having issues with your iPhone not being seen in iTunes because of the Apple Mobile Device not working. When you reinstalled iTunes, did you uninstall iTunes first? Take a look at the article below and uninstall iTunes and its associating software in the order that it lists and then reinstall iTunes. Let me know if this works out for you.
Remove and reinstall iTunes and related software components for Windows Vista, Windows 7, or Windows 8
https://support.apple.com/en-us/HT204275
Take care,
-Norm G.

Need to log into Mobility Sevices Engine

Hi Everyone.
Sorry if anyone already addressed this issue before. I just can't find it.
The preious wireless technician left our company and didn't leave the password. Now we need to re-ip the WCS, WLC and MSE. The only problem left is with the MSE.
From the WCS, I can see the username for the MSE is admin, and the password shows asterisks.
Also from Security Index Detailed Report in the WCS, I can see the following description,
Device Security Issue: Mobility Service Engine Mobility Services Engine user has default password configured.
Security Solution: Configure strong password for the users on the Mobility Services Engine
I did a research and from this link (http://www.cisco.com/en/US/docs/wireless/mse/3350/6.0/CAS/configuration/guide/msecg_ch2_CAS.html), it's saying "
The default username and password are both admin. "
However when I tried to SSH to this MSE(model# 3310), MSE asked for username and password. I put admin/admin there and got an error mesage of "password authentication failed". I am thinking there is another default password for this MSE. Anybody can help? I don't want to go through the password recovery process. Another question is that if anybody can point me a link of how to change the IP address of the MSE.
Any input will be greatly appreciated.
Robert

Robert,
If you don't have the password, then you'll have to go through the recovery process.
http://www.cisco.com/en/US/docs/wireless/mse/3350/quick/guide/mse_qsgmain.html#wp1053115
To change the IP, you can go through the setup script once you can get in.
/opt/bin/setup.sh
IIRC
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

Azure Mobile Services

First of all thank you responding.
I am about to create a windows app within which the user enters the email id for confirmation. I would like to store the email id in the cloud. How to create a sql database in Azure. i have a trial subscription and my region is India. Also I need to
create a mobile service. It says that the service is disabled in the free trial subscription. But in some sites they say in the free trial I can get 10 Mobile services for free. Plz help me through this....

The free trial subscriptions are mainly geared towards development. So since your free service shows up as disabled, it means you have exceeded one of the quota limits on a free subscription. You would need to upgrade to a paid subscription to continue
utilizing your service.
With regards to creating the SQL Database in Azure, Azure mobile services makes this very simple. Here's a good start regarding
Azure Mobile services.
Abdulwahab Suleiman

Start studying on Mobility Services Engine

Similar Messages

Maybe you are looking for