"start up disk is full" now gray screen

Help!
I was getting the "start up disk is full" error message. I deleted and transfered files, and had stopped receiving the warning. Then my Iphoto gave an error message that it needed to "repair". When I "repair"ed iphoto - all of my photos that I had transfered or deleted came back.I photo started to not run proberly, and then went to gray screen before I could delete more and empty the trash. Now all I have is a gray screen - only my password screen comes on and then gray screen - no function at all on the laptop at all. Anyone have any ideas?

Repair Disk
Steps 1 through 7
http://support.apple.com/kb/PH5836?viewlocale=en_US

Similar Messages

IMac says start up disk is full. now what?

iMac says start up disk is full. now what?

Here are two links that may help.
Where did my Disk Space go?
http://macmost.com/what-to-do-when-your-hard-drive-is-full.html

Mac Air says start up disk is full

MMac air says start up disk is full & now won't turn on. What can I do?

Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.

My start up disk is full, and now i cant access my user areas, just a blank screen appears. Any ideas ?

My Start up disk is full, as it keeps telling me, and now i can't access my user areas. just a blank screen after logging in.
any Ideas. I've tried connecting to my Mac desk top, with a thunderbolt cable but nothing happened.

Try this.
1. Start up in Safe Mode.
    http://support.apple.com/kb/PH11212
2. Empty Trash.
    http://support.apple.com/kb/PH10677
3. Delete "Recovered Messages", if any.
    Hold the option key down and click "Go" menu in the Finder menu bar.
    Select "Library" from the dropdown.
    Library > Mail > V2 > Mailboxes
    Delete "Recovered Messages", if any.
    Empty Trash. Restart.
4. Repair Disk
    Steps 1 through 7
    http://support.apple.com/kb/PH5836

HT1492 Start-up disk is full and can't go past the blue screen; can't delete read-only files on single-user mode. Please help.

I have had my Mac mini for about 6 years and I guess it had enough of me (haha), so the start-up disk got full and it shut down before I could empty files on my drive. Unfortunately, all these years I hadn't backed up anything and now I can't access anything since it won't boot past the apple logo (and the blue screen for that matter). I have tried rebooting (holding shift as the mac mini loads), but that didn't help since the start-up disk will still be full and stuck on the blue screen. I am now trying the single-user mode (holding command key+s), and I tried to delete files in the trash bin but all of the files are read-only and access is denied! so I basically can't delete anything on the mac mini (it says "Root device is mounted read-only"). So the key here is to change the permissions but I don't know how to exactly do that. Can someone help me figure this out? (and type the command in the unix language please!!) [ Note: We have two users on this mac mini if that helps.]

Run the following command:
mount -uw /
This isn't a permissions issue.
(87807)

My start up disk is full and the now the mac will not start

How do I get on my computer when my start up disk is full?

If you don't have a recent backup, then all your files will be lost.
Clean Install of Snow Leopard
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. Be sure you configure your initial admin account with the exact same
         username and password that you used on your old drive. After you finish Setup
         Assistant will complete the installation after which you will be running a fresh
         install of OS X. You can now begin the update process by opening Software
         Update and installing all recommended updates to bring your installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Macbook air won't turn on and the screen will go white. It says that the start up disk is full. HELP

When I turn my macbook air on it sends me a message saying that my start up disk is full and that I have to free up some space. When I log in into my account the screen will go white and I won't be able to do anything. I tried to restart my computer in safemode holding down the shift key while restarting it but it won't work. HELP PLEASE.

If you could boot from an external OS X boot drive then you could delete some files. You probably don't have such a HDD/Thumb drive but a Genius at an Apple Store or an Apple Authorized Service Provider could help you. This is not a hardware repair so a Genius should not need to charge you for this service.
Genius reservation http://www.apple.com/retail/geniusbar/ .
or find an Apple Authorized Service Provider https://locate.apple.com/country
After it is healthy again I would buy a new external HDD and use Carbon Copy Clone or Super Duper! to create a bootable clone. Keeping a clone current is also an excellent backup methodology in addition to Time Machine.
Commonly used backup methods:
https://discussions.apple.com/docs/DOC-3045
Methodology to protect your data. Backups vs. Archives. Long-term data protection

Start up disk is full - what now?

Getting message that my start up disk is full-yikes- and that I need to delete files. I deleted all of my downloads. Seemed like a lot, but the message came back. What else can I purge that will actually make a difference??
My computer is clearly on its last leg - fully backed up though - but I'd like to hang on for a bit longer while I figure out what to purchase next!

Hope this helps.
1. Empty Trash.
    http://support.apple.com/kb/PH10677
2. Delete "Recovered Messages", if any.
    Hold the option key down and click "Go" menu in the Finder menu bar.
    Select "Library" from the dropdown.
    Library > Mail > V2 > Mailboxes
    Delete "Recovered Messages", if any.
    Empty Trash. Restart.
3. Repair Disk
    Steps 1 through 7
    http://support.apple.com/kb/PH5836
4. Disk space / Time Machine ?/ Local Snapshots
   http://support.apple.com/kb/ht4878
5. Re-index Macintosh HD
   System Preferences > Spotlight > Privacy
   http://support.apple.com/kb/ht2409

My iMac does not start up as usual. Start up disk is full message and I do not get normal desk top. Please can you help? Thanks

My iMac does not start up as usual. I now get a ' start up disk is full. You need to make space available on your start up disk by deleting files' message.
I am able to key my log on password however I just get the purple galaxy screen with no desktop.
If I try to use the keyboard I get a tone when pressing the keys.
Has worked perfectly well up until I got this dusk full message.
Can anyone help please. Thanks

Your going to have to follow the Data Recovery Efforts page here to be able to access your drive and remove files without booting the computer.
You can't open the iMac so you will need OS X booted from a external drive or via Firewire Target Disk Mode using another Mac.
https://discussions.apple.com/docs/DOC-3172
I would concentrate on Movies as this is a big source of large files to free up room.
Read Storage Drive here
https://discussions.apple.com/docs/DOC-3045
If you not handy with computers, your going to have to hire a local service or provide the info above to someone you know who can, it's not easy.

My macbook air won't load. Says start up disk is full but I can't get the home page to open

My Macbook air won't load. Says the start up disk is full but won't open the home page so I can do anything about it

Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.

My Start Up Disk is Full and I can get no acces to anything when the computer starts

The computer turns on and I can get no acces to anything. It display a message "Your Start Up Disk is Full" and comes to a white screen. I can only move the mouse but there is nowhere to click.
How can I delete any files, so the computer can come back to life?? Is there any way I can acces those files??
I'm using 250GB and this Mac has 500GB total memory.

Supposedly one can hold the Shift key down while booting (Safe Mode) and that's supposed to allow one to boot the machine when the startup disk is full.
Step by Step to fix your Mac
If that works, then use a storage drive (not TimeMachine) to move excessive files too likely starting with Movies (large and easy) or iTunes supscirptions downloads which have gotten out of control.
Most commonly used backup methods
Another method is to create a boot drive on a external drive, this then will allow one to option key boot the computer and remove files off of the internal drive, allowing the free space needed for OS X to swap stuff to the drive and operate.
Create a data recovery, undelete boot drive
Now for some reason it takes rebooting the original drive to get OS X to recognize there is free space available again, so reboot the machine normally (no Shift key). Just saying that because you may be wondering how come it does't register when you delete stuff later.

TS1587 How can I get my Mac to run properly when it starts up and goes into a Gray Screen?

To cut a long story short here's basically what happened:
Had problems with signing into my Mac, not quite sure what happened. So after a lot playing around with some stuff, I tried to run a Start Up disk, which is now stuck in my Mac and it just goes to a GRAY screen everytime I go to power up my Mac. Have tried all sorts to get it going, but to know avail. There's not even a start up Chime. HELP PLEASE Thanks in advance.

No startup chime is usually the sign of a hardware failure. If you have an installer disc (or if the disc that's stuck in the optical drive is an installer disc) then you need to try booting from it. But the first thing you need to do is:
Intel-based Macs: Resetting the System Management Controller (SMC)
Resetting your Mac's PRAM and NVRAM
Next:
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo appears.
5. Wait for installer to finish loading.
Repair the Hard Drive and Permissions
After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If you can get this far, then you may be able to reinstall OS X without erasing the drive. But you will need to tell us what version of OS X you are using.

How do I rectify start up disk almost full. I am new to Macs and struggling

How do I rectify a start up disk almost full message? Never had this until I put a load of photos on to my Mac book air

Hello Kirkcaldy Ronnie,
As Plotinus Veritas said take a backup for your Images on External Hard Disk.
As your Macbook Air Startup disk is full and if you are unable to do anything on your Mac follow the below process to boot your Mac in Safe Mode and then delete some files on your Mac to free up some disk space and then you should be able to boot in Normal Mode.
Steps : > Turn of your Macbook completely by holding the Power On/Off key on your Mac's keyboard > Turn On your Mac again and simultaneously press and hold the Left Shift key on your keyboard and this should take your Macbook in Safe Mode. ( Note : You will see a loading bar at startup when you boot your Mac in safe mode and your Mac will take some time to boot) > Once you login to the User Account on your Mac go ahead an delete as many files as you can from your Mac to free up some space (try to delete and make as much space as you can and keep at least 20% space free of the total amount of your disk space on your Mac Disk) and also empty the Trash of your Mac to completely remove the files from your Mac. > Now you can restart your Mac and let it start in Normal mode and check of you are able to login. If you are able to login in normal mode then try to transfer the data which you do not use regularly on an external hard disk and keep internal space free as much as you can as that will help you to get a better performance of your Mac. Hope this helps you.

How do i solve the 'start up disk almost full' problem?

when i turn on my macbook air, it comes up with a warning message that says 'start up disk almost full' and that i need to clear some space, how do i do this?

For information about the Other category in the Storage display, see this support article.
Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
iPhoto ▹ Empty Trash
Do the same in other applications, such as Aperture, that have an internal Trash feature. Then reboot. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
When Time Machine backs up a portable Mac, some of the free space will be used to make local snapshots, which are backup copies of recently deleted files. The space occupied by local snapshots is reported as available by the Finder, and should be considered as such. In the Storage display of System Information, local snapshots are shown asBackups. The snapshots are automatically deleted when they expire or when free space falls below a certain level. You ordinarily don't need to, and should not, delete local snapshots yourself. If you followed bad advice to disable local snapshots by running a shell command, you may have ended up with a lot of data in the Other category. Reboot and it should go away.
See this support article for some simple ways to free up storage space.
You can more effectively use a tool such as OmniDiskSweeper (ODS) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
Install ODS in the Applications folder as usual. Quit it if it's running.
Triple-click anywhere in the line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The application window will open, eventually showing all files in all folders, sorted by size with the largest at the top. It may take a few minutes for ODS to finish scanning.
I don't recommend that you make a habit of doing this. Don't delete anything while running ODS as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with ODS, quit it and also quit Terminal.

How can I find where this came from? - start up disk almost full

Hi, my mac began saying this to me today "Start up disk almost full"
So I began deleting files. I deleted a lot via DiskWave.
But now Diskwave says I have enough space but my mac sure doesn't.
What do I do? What's all that 'other' stuff and where can I find it?
Thanks in advance!

For information about the Other category in the Storage display, see this support article. If the Storage display seems to be inaccurate, try rebuilding the Spotlight index.
Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
iPhoto ▹ Empty Trash
Do the same in other applications, such as Aperture, that have an internal Trash feature. Then restart the computer. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
When Time Machine backs up a portable Mac, some of the free space will be used to make local snapshots, which are backup copies of recently deleted files. The space occupied by local snapshots is reported as available by the Finder, and should be considered as such. In the Storage display of System Information, local snapshots are shown as Backups. The snapshots are automatically deleted when they expire or when free space falls below a certain level. You ordinarily don't need to, and should not, delete local snapshots yourself. If you followed bad advice to disable local snapshots by running a shell command, you may have ended up with a lot of data in the Other category. Ask for instructions in that case.
See this support article for some simple ways to free up storage space.
You can more effectively use a tool such as OmniDiskSweeper (ODS) or GrandPerspective (GP) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one. Note that ODS only works with OS X 10.8 or later. If you're running an older OS version, use GP.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS or GP can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
Install the app you downloaded in the Applications folder as usual. Quit it if it's running.
Triple-click anywhere in the corresponding line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
sudo /Applications/GrandPerspective.app/Contents/MacOS/GrandPerspective
Launch the built-in Terminal application in any of the following ways:
Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. You'll be prompted for your login password, which won't be displayed when you type it. Type carefully and then press return. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The application window will open, eventually showing all files in all folders, sorted by size. It may take a few minutes for the app to finish scanning.
I don't recommend that you make a habit of doing this. Don't delete anything as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with the app, quit it and also quit Terminal.

"start up disk is full" now gray screen

Similar Messages

Maybe you are looking for