Starting 6735b in safe mode command prompt
I have a 6735b laptop running XP. I've had trouble starting Windows normally, but have been able to get to a command prompt from the Start in Safe Mode w Command Prompt. The first line that came up was C:\Documents and Settings\Administrator. Any help on where to go from here to get this thing restarted?
This question was solved.
View Solution.
Hi
Can you try chkdsk /f
Check if unit loads to safe mode you can try doing a system restore.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath
Similar Messages
-
HT1455 What if my computer will not start up in safe mode? What next?
What is the remedy for a MacBook that will not start up in safe mode? The gray apple icon and progress wheel appear, I let go the shift key and the whole thing shuts off again. Please help. Thank you.
My understanding is that the Apple logo is produced by the disk and the spinning wheel shows that the software boot process has started.
1 - Shut down your Mac
2 - Press the power button to start and
3 - Immediately press and hold the Command (Apple) key and the S key
4 - At the prompt type the following and then hit return:
/sbin/fsck -fy
fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issues were found:
** The volume (name_of_volume) appears to be OK
If fsck found issues and has altered, repaired, or fixed anything, it will display this message:
***** FILE SYSTEM WAS MODIFIED *****
Important: If this message appears, repeat the fsck command you typed in step 4 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do). When fsck reports that your volume is OK, type the following at the prompt and hit return:
reboot
Your computer should start up normally and allow you to log in.
Good luck. -
Help: Can't start up in Safe Mode!
I'm trying to fire up in Safe Mode to do a few Spotlight housekeeping tasks but my Mac won't have it. When I try start up Safe it gets no further than the Grey Apple Logo and spinning wheel. After a short while the fans spin up to full speed and nothing else happens. I have to force the Mac to shut down and I can then start up again normally.
Any help on this would be much appreciated as there may come a time when I NEED to start up in Safe Mode.
Thanks in advance. Derek.Hi-
Might want to try a Single User mode boot (command +s) and run fsck.
-Startup in Single User mode.
-At the command-line prompt, type */sbin/fsck -fy*. Press Return.
fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
The volume (nameofvolume) appears to be OK
-If fsck found issues and has altered, repaired, or fixed anything, it will display this message:
FILE SYSTEM WAS MODIFIED
Important: If this message appears, repeat the fsck command again, until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
-When fsck reports that your volume is OK, type reboot at the prompt and then press Return.
-Your computer should start up normally and allow you to log in.
After this, try a Safe mode boot, again.
Resolve startup issues and perform disk maintenance with Disk Utility and fsck -
My MB is always starting up in safe mode... why? What to do to start-up normally? Please help.
Hi,
I am frequently having troubles with my MB. Different types of troubles. Couldn't solve a single one yet.
I have performed reboot MB in safe mode-- hold down the left shift key after the start up tone till the spinning gear appeared.
Few hours back i performed that, and since then it just starting up in safe mode without holding the any shift key. I have password protected log-in and each time the dialog box shown the safe mode, not the normal boot as it used to be. I restarted so many times, but same result.
I started-up by holding down the Option key, dialog box showing the same thing "safe mode" and same result.
I started-up in single user mode, and then typed reboot, then pressed enter/return button, but dialog box shown the same and it started up in safe mode after entering the password.
While in the safe mode, i have selected the Mac OS X 10.4.11 from the preference pane, then restarted, but all produced the same result, same dialog box showing the safe mode.
I couldn't take the screen shot of that dialog box that appears before starting up.
I am currently using the internet while in safe mode, and using ethernet adapter- a AirStream 1100 F25 external modem attached to the USB port. I don't know if that is good for my MB to use internet on the safe mode.
I used disk utility and verified the disk during the safe mode, i don't know if that is right or wrong to perform that utility in safe mode, but it all appeared as normal. You can see that from the following image.
Few days back, i performed the disk utility to verify disk while on the normal boot. But the result shown the red marks, please see the following image for details.
Hardware Overview:
Model Name: MacBook
Model Identifier: MacBook2,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache (per processor): 4 MB
Memory: 1 GB
Bus Speed: 667 MHz
Boot ROM Version: MB21.00A5.B07
SMC Version: 1.13f3
Serial Number: 4*********M
Sudden Motion Sensor:
State: Enabled
BANK 0/DIMM0:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
BANK 1/DIMM1:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 2745
Remaining Capacity (mAh): 2745
Amperage (mA): 133
Voltage (mV): 12575
Cycle Count: 507
AC Charger Information:
Connected: Yes
Charging: No
Hardware Configuration:
UPS Installed: No
Intel ICH7-M AHCI:
Vendor: Intel
Product: ICH7-M AHCI
Speed: 1.5 Gigabit
Description: AHCI Version 1.10 Supported
TOSHIBA MK1234GSX:
Capacity: 111.79 GB
Model: TOSHIBA MK1234GSX
Revision: AH008B
Serial Number: Z6M7T4FTT
Native Command Queuing: Yes
Queue Depth: 8
Removable Media: No
Detachable Drive: No
BSD Name: disk0
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 111.47 GB
Available: 24.09 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
TOSHIBA MK1234GSX:
Capacity: 111.79 GB
Model: TOSHIBA MK1234GSX
Revision: AH008B
Serial Number: Z6M7T4FTT
Native Command Queuing: Yes
Queue Depth: 8
Removable Media: No
Detachable Drive: No
BSD Name: disk0
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 111.47 GB
Available: 24.09 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
System Software Overview:
System Version: Mac OS X 10.4.11 (8S2167)
Kernel Version: Darwin 8.11.1
Boot Volume: Macintosh HD
Please help me out. Let me know how to start-up normally. By the way, my superdrive is not detecting DVDs including the OS dvds, but it read and write the CDs. So, It is not possible to reinstall OS early, at least not before the having the back up of the data. Please help me with contingency plan/s or as you think fit.
Thank you. Look forward to your reply.
<Personal Information Edited by Host>Maximillianmann,
depending upon how full “almost full” actually is, that could be the problem.
You can try this, if you have Mac OS X 10.7 or newer installed, to see if it’s not related to your disk being almost full: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the Mac OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Once you hear the startup chime, try booting into Safe mode; does it let you do so now? -
I've followed the directions here 8 times now:
http://docs.info.apple.com/article.html?artnum=107393
I've tried it with various timing alterations, and I just can't seem to get started up in safe mode.
Any clue what I might be doing wrong?
Thanks.Okay, I solved my own problem. Figured I'd post it here, just in case it might help someone else. Though, it probably won't. My set-up is pretty rare.
My keyboard isn't plugged into my computer. It's plugged into my monitor, which has 4 USB ports. Evidently, those USB ports don't get loaded until too late in the start-up process, for me to take advantage of start-up commands.
When I plugged the keyboard directly into the computer, it worked fine. -
I shut down my macbook pro and now I started up and it started in the safe mode
I shut down my MacBook Pro yesterday and when I started up today, it keeps starting up in safe mode, what do I need to do?
Welcome to the Apple Support Communities
Does your Mac start properly in safe mode? If so, try resetting the PRAM > http://support.apple.com/kb/HT1379 This will reset the "boot args", so OS X should start into safe mode. Also, you should verify that the storage of the computer is OK, so open Disk Utility, select "Macintosh HD" on the sidebar and verify the drive. If there's a problem, start in OS X Recovery (holding Command and R keys while your Mac is starting) and repair it -
Lost user profile and disk0s2: I/O error during start up in safe mode
My almost 2 year old Mac Book Pro (10.7.5) started lagging and rainbow spiraling last week and now it usually doesn't make it to the login page after boot up. It stays on the gray apple screen until I hold the power button to power it off.
If it makes it to the login page, after 10-20 minutes on the gray apple screen, my primary user profile is not there but the standadr guest user and my blank student user are still there and do work with many rainbow spirals interruptions.
I started it in safe mode and have also tried starting it with command-option-p-r to reset the PRAM and it went through the double start up sounds but still did not load my primary user profile on the login screen, still after a very long boot up process.
I then started it up in safe mode and watched the progress it seemed to run cleanly through lines and lines of code until it hit a bunch of lines of "disk0s2: I/O error" ...
Are my computer's brains toast??? I just did a Time Machiene back up to an external hard drive as few days ago ... but what needs to be done with my computer?"disk0s2: I/O error" ...
This indicates a disk failure, though a hardware failure involving the connection between the HD and logic board is also a remote possibility. If you are able to successfully repair it with Disk Utility, it will probably recur.
Replace the disk and restore from your Time Machine backup. Hard disks are not expensive and it's easy enough to replace it yourself. -
Why does my imac start up in safe mode
hi, imac starts up in safe mode. not every time, only when progress bar appears at startup.
I have had the Logic board replaced under warranty but it still started in safe mode.
sometimes when it has started the wifi symbol is missing and no wifi, other times the sound is not there and the symbol is missing on the top bar.
I then have to restart and it comes up good. sometimes the desktop top bar is not there until I press the mouse and then it appears.
don't know what to do, any Ideas anybody?How often does this happen? Do you have automatic updating enabled in Software Update? If so, then it's possible those were firmware updates being installed, not startup in safe mode. In a safe mode startup you are initially prompted for your password before proceeding past login.
If a firmware update was happening then the computer will restart on its own. If you interrupt the process then the update isn't installed, so it will try again on the next restart.
Safe mode is initiated by holding down the SHIFT key at restart. It should not occur without user intercession. -
My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected
If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages. -
My MBP didn't recognise my password, started it in safe mode, I can see my files, but I don't know what to do next, as the image of reset password isn't selectable. I just moved from PC. Need help please...
Safe mode is not what you want in this case. Reboot to recovery mode - hold down cmd-R as the Mac reboots. Go past the language-selection screen, click the Utilities menu, then Terminal. Type:
resetpassword
Followed by the return key, and follow the prompts. Reboot normally when done.
Matt -
Mac Pro will not shut down, wakes from sleep and will not start up in safe mode (restarts).
Wakes from sleep about every 4.5 mins, here is the log from wake from sleep:
7/30/12 8:43:24.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:43.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:43.429 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:47:46.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:47:46.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:47:50.459 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0d2a8340 {NSUnderlyingError=0x7f8b0c4c1b50 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:47:52.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:47:52.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Graphics suppressed 10291 ms
7/30/12 8:47:53.293 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:47:53.305 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:47:53.308 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f8dd800][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f8dd800][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f93da00][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::start] entered
7/30/12 8:47:54.304 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:47:54.308 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:48:28.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:48:28.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:48:29.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:48:29.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::stop] entered
7/30/12 8:48:29.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:52:47.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:47.497 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:52:50.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:52:50.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:52:54.459 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0c084f70 {NSUnderlyingError=0x7f8b10a128d0 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:52:56.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Graphics suppressed 10340 ms
7/30/12 8:52:57.341 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:52:57.354 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:52:57.355 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f8e4c00][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f8e4c00][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f91b800][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::start] entered
7/30/12 8:52:58.354 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:52:58.358 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:53:33.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:53:33.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:53:33.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:53:33.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::stop] entered
7/30/12 8:53:33.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:57:51.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:57:51.435 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:57:54.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:57:54.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:57:58.228 AM fseventsd[76]: SLOWDOWN: client 0x7f8a4e007c00 (pid 2824) sleeping due to too many errors (num usleeps 299)
7/30/12 8:57:58.462 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0d295160 {NSUnderlyingError=0x7f8b0b4bd590 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.213 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Graphics suppressed 10334 ms
7/30/12 8:58:01.341 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:58:01.349 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f930400][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f930400][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f941400][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::start] entered
7/30/12 8:58:02.225 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:58:02.229 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:58:37.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:37.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:58:37.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:58:37.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::stop] entered
7/30/12 8:58:37.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 9:02:55.000 AM kernel[0]: Previous Sleep Cause: 5
Will not shut down, restarts at end of shut down. Log:
7/30/12 8:43:24.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:43.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:47:43.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:43.429 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:47:46.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:47:46.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:47:50.459 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0d2a8340 {NSUnderlyingError=0x7f8b0c4c1b50 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:47:52.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:47:52.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:47:53.000 AM kernel[0]: Graphics suppressed 10291 ms
7/30/12 8:47:53.293 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:47:53.305 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:47:53.308 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f8dd800][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f8dd800][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f93da00][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:47:53.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::start] entered
7/30/12 8:47:54.304 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:47:54.308 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:48:28.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:48:28.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:48:29.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:48:29.000 AM kernel[0]: [ffffff805f939300][AppleMultitouchDevice::stop] entered
7/30/12 8:48:29.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:52:47.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:52:47.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:47.497 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:52:50.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:52:50.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:52:54.459 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0c084f70 {NSUnderlyingError=0x7f8b10a128d0 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:52:56.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:52:57.000 AM kernel[0]: Graphics suppressed 10340 ms
7/30/12 8:52:57.341 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:52:57.354 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:52:57.355 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f8e4c00][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f8e4c00][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f91b800][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:52:57.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::start] entered
7/30/12 8:52:58.354 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:52:58.358 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:53:33.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:53:33.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:53:33.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:53:33.000 AM kernel[0]: [ffffff805f95c600][AppleMultitouchDevice::stop] entered
7/30/12 8:53:33.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 8:57:51.000 AM kernel[0]: Previous Sleep Cause: 5
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:57:51.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:57:51.435 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:57:54.000 AM kernel[0]: Ethernet [Intel82574L]: Link up on en0, 1-Gigabit, Full-duplex, Symmetric flow-control, Debug [796d,af48,0de1,0200,cde1,3c00]
7/30/12 8:57:54.000 AM kernel[0]: Intel82574L::setLinkStatus - active 1face000, b
7/30/12 8:57:58.228 AM fseventsd[76]: SLOWDOWN: client 0x7f8a4e007c00 (pid 2824) sleeping due to too many errors (num usleeps 299)
7/30/12 8:57:58.462 AM CalendarAgent[202]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7f8b0d295160 {NSUnderlyingError=0x7f8b0b4bd590 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://david%[email protected]/principals///david%[email protected]/principals/, NSErrorFailingURLKey=https://david%[email protected]/principals///david%[email protected]/principals/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::timeoutHandler - no link - reset the chipset once 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.213 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:58:01.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:01.000 AM kernel[0]: Graphics suppressed 10334 ms
7/30/12 8:58:01.341 AM configd[17]: network changed: v4(en0-:192.168.1.4) DNS- Proxy- SMB
7/30/12 8:58:01.349 AM blued[84]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f930400][BNBTrackpadDevice::init][75.15] init is complete
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f930400][BNBTrackpadDevice::handleStart][75.15] returning 1
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f941400][AppleMultitouchHIDEventDriver::start] entered
7/30/12 8:58:01.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::start] entered
7/30/12 8:58:02.225 AM configd[17]: network changed: v4(en0+:192.168.1.4) DNS+ Proxy+ SMB
7/30/12 8:58:02.229 AM mDNSResponder[67]: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.1.4)
7/30/12 8:58:37.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face001, 0
7/30/12 8:58:37.000 AM kernel[0]: Intel82574L::setLinkStatus - not active 1face000, 0
7/30/12 8:58:37.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::willTerminate] entered
7/30/12 8:58:37.000 AM kernel[0]: [ffffff805f985a00][AppleMultitouchDevice::stop] entered
7/30/12 8:58:37.000 AM kernel[0]: Wake reason: ? (Network)
7/30/12 9:02:55.000 AM kernel[0]: Previous Sleep Cause: 5
And will not start up in safe mode. I have reset PRAM and SMC. Also restarted with no startup items, no luck. Had the problem of waking from sleep and not shutting down in 10.7, updated to 10.8 hoping for fix, no luck. Any help would be appreciated.
ThanksHi, this log has some similarities to my ipod touch which seems to be not sleeping properly due to wireless issues. Can I check - are you using a wifi connection - if so have you tried ethernet?
log entries below ...
Sep 5 00:28:58 Peters-iPod mDNSResponder[34] <Error>: mDNS_RegisterInterface: Frequent transitions for interface en0 (FE80:0000:0000:0000:5AB0:35FF:FE35:C9B7)
Sep 5 00:28:58 Peters-iPod mDNSResponder[34] <Error>: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.0.95)
Sep 5 00:28:58 Peters-iPod configd[44] <Notice>: network configuration changed.
Sep 5 00:28:58 Peters-iPod UserEventAgent[12] <Warning>: DEBUG: Changing WiFi state: 1
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 1
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::enableHTClock(): Failed to read HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::retainClocks() Failed to enable HT Clock, SDIO Cmd Timeout
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::txPacket() Unable to wake bus; error SDIO Cmd Timeout
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 2
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::disableHTClock(): Failed to write HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::releaseClocks(): Failed to disable HT clock: SDIO Cmd Timeout
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCmdManager::processPendingList(): Failed to send sync command WLC_GET_BSS_INFO (136) to device, SDIO Cmd Timeout. transID 48928, respLen 1152.
Sep 5 00:29:27 Peters-iPod kernel[0] <Debug>: AppleBCMWLANNetManager::updateBSSInfo(): WLC_GET_BSS_INFO Failed SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 3
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::enableHTClock(): Failed to read HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::retainClocks() Failed to enable HT Clock, SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::txPacket() Unable to wake bus; error SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 4
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::disableHTClock(): Failed to write HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::releaseClocks(): Failed to disable HT clock: SDIO Cmd Timeout
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCmdManager::processPendingList(): Failed to send sync command WLC_GET_BSS_INFO (136) to device, SDIO Cmd Timeout. transID 48929, respLen 1152.
Sep 5 00:29:32 Peters-iPod kernel[0] <Debug>: AppleBCMWLANNetManager::updateBSSInfo(): WLC_GET_BSS_INFO Failed SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 5
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::dumpDebugInfo(): CRITICAL ERROR: handleTransferError
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::logState(): Tx: seq 185, credit 191, flow 0x0; Rx: seq 167
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::logState(): state 0x23, sd-clk +1, sd-rate 20250000 Hz
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::logClockState(): Failed to read HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): Triggered Watchdog after 6 errors (last was SDIO Cmd Timeout)
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::enableHTClock(): Failed to read HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::retainClocks() Failed to enable HT Clock, SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::txPacketChain() Unable to wake bus; error SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleTransferError(): SDIO Cmd Timeout, 1, 0
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::disableHTClock(): Failed to write HT Clock register, SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::releaseClocks(): Failed to disable HT clock: SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::doOutputPacketChain(): Packet transmission failure: SDIO Cmd Timeout
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::handleWatchdogTimeout(): Watchdog timer fired
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::watchDogReset(): fStateFlags(0x140E3), thread(00040532)
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::halt()
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLAN Left BSS: @ 0xc11a7a00, BSSID = 00:18:4d:67:54:12, rssi = -45, rate = 54 (100%), channel = 7, encryption = 0x8, ap = 1, failures = 0, age = 39, ssid[ 9] = "polarbear"
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AirPort: Link Down on en0. Reason 1 (Unspecified).
Sep 5 00:29:35 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::powerOn()
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: AppleBCMWLANChipManagerSdio4329::downloadFirmware(): start
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: AppleBCMWLANChipManagerSdio4329::downloadFirmware(): finish
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: BCMWLAN Firmware Version: wl0: Aug 26 2011 02:34:35 version 4.221.54.22
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: nvram file version 4.221.54.22
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::initFirmware(): country code set to XX2
Sep 5 00:29:36 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::initFirmware(): Packet glomming ON (mode=7)
Sep 5 00:29:36 Peters-iPod wifid[13] <Error>: WiFi:[368494176.616677]: Processing link event DOWN
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::initFirmware(): There was an existing PNO config, reprogramming
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore:initFirmware(): 2469 RoamScan feature is not enabled for this platform
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::initFirmware(): successful initialization
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore:initFirmware(): 2496 PropTxStatus feature is not enabled for this platform
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::powerOn(): stateFlags(40e3)
Sep 5 00:29:37 Peters-iPod kernel[0] <Debug>: AppleBCMWLANBusInterfaceSdio::powerOn()
Sep 5 00:29:37 Peters-iPod UserEventAgent[12] <Warning>: DEBUG: Changing WiFi state: 0
Sep 5 00:29:37 Peters-iPod configd[44] <Notice>: network configuration changed.
Sep 5 00:29:37 Peters-iPod mDNSResponder[34] <Error>: DeregisterInterface: Frequent transitions for interface en0 (192.168.0.95)
Sep 5 00:29:37 Peters-iPod apsd[49] <Warning>: <APSCourier: 0x17a190>: Stream error occurred for <APSTCPStream: 0xfe95de0>: Error Domain=NSPOSIXErrorDomain Code=57 "The operation couldn’-t -b-e -c-o-m-p-l-e-t-e-d-. -S-o-c-k-e-t -i-s -n-o-t -c-o-n-n-e-c-t-e-d-" -U-s-e-r-I-n-f-o-=-0-x-1-8-2-5-e-0 -{-}
Sep 5 00:29:37 Peters-iPod apsd[49] <Warning>: <APSCourier: 0x17a190>: Stream error occurred for <APSTCPStream: 0xfe95e40>: Error Domain=kCFErrorDomainCFNetwork Code=2 "The operation couldn’-t -b-e -c-o-m-p-l-e-t-e-d-. -(-k-C-F-E-r-r-o-r-D-o-m-a-i-n-C-F-N-e-t-w-o-r-k -e-r-r-o-r -2-.-)-" -U-s-e-r-I-n-f-o-=-0-x-f-e-8-e-2-4-0 -{-k-C-F-G-e-t-A-d-d-r-I-n-f-o-F-a-i-l-u-r-e-K-e-y-=-8-}
Sep 5 00:29:39 Peters-iPod wifid[13] <Error>: WiFi:[368494179.091333]: Processing link event UP
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: AppleBCMWLANCore::setASSOCIATE() [wifid]: lowerAuth = AUTHTYPE_OPEN, upperAuth = AUTHTYPE_WPA2_PSK, key = CIPHER_PMK , don't disassociate .
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: [139978.345418625]: AppleBCMWLANNetManager::prepareToBringUpLink(): Delaying powersave entry in order to get an IP address
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: AppleBCMWLAN Joined BSS: @ 0xc067f800, BSSID = 00:18:4d:67:54:12, rssi = -49, rate = 54 (100%), channel = 7, encryption = 0x8, ap = 1, failures = 0, age = 1, ssid[ 9] = "polarbear"
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: AirPort: Link Up on en0
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: en0: BSSID changed to 00:18:4d:67:54:12
Sep 5 00:29:39 Peters-iPod kernel[0] <Debug>: AppleBCMWLANJoinManager::handleSupplicantEvent(): status = 6, reason = 0, flags = 0x0, authtype = 0, addr = 00:00:00:00:00:00
Sep 5 00:29:40 Peters-iPod kernel[0] <Debug>: [139980.075593458]: AppleBCMWLANNetManager::receivedIPv4Address(): Received address 192.168.0.95, entering powersave mode 2
Sep 5 00:29:40 Peters-iPod configd[44] <Notice>: network configuration changed.
Sep 5 00:29:40 Peters-iPod configd[44] <Notice>: Captive: en0: Not probing 'polarbear' (protected network)
Sep 5 00:29:40 Peters-iPod mDNSResponder[34] <Error>: mDNS_RegisterInterface: Frequent transitions for interface en0 (FE80:0000:0000:0000:5AB0:35FF:FE35:C9B7)
Sep 5 00:29:40 Peters-iPod mDNSResponder[34] <Error>: mDNS_RegisterInterface: Frequent transitions for interface en0 (192.168.0.95)
Sep 5 00:29:40 Peters-iPod configd[44] <Notice>: network configuration changed.
Sep 5 00:29:41 Peters-iPod UserEventAgent[12] <Warning>: DEBUG: Changing WiFi state: 1 -
Had to start Firefox in safe mode cause it kept crashing after i deleted the file. Now Fire fox Crashes every time I open it and I have to put it in safe mode just to use it, also it's not syncing with my iPad.
If you use Norton software, try disabling your Norton extensions. As of last week, there were severe compatibility issues with Firefox 24.
-
Is there a way to change the hotkey for starting firefox in safe-mode?
The current default hotkey is shift. Holding it when starting firefox will start it in safe mode (true story). My super duper favorite handy windows hotkey for starting programs pinned to the task bar in windows 7 is windows_key + shift + #, and that conflicts with the firefox setting, and i always end up starting firefox in safe mode because im that lazy.
Greetings!
I'm an irssi user, and I have awesome mouse gesture addon for it, and I'm afraid I can't live without it anymore.. But it requires Shift key for opening links, therefore Firefox, as my default browser, always starts in Safe mode :(
I'm not a programmer, easiest workaround would be modifying the irssi addon, but I suck on that, too.
If there's a way to bypass Safe Mode in Firefox, or at least a way to change the Shift key to something else, that would make my miserable life a tad easier. -
IMac won't start up in safe mode
Thanks to those that have helped getting my so far. Really appreciated.
When attempting to startup in safe mode the grey progress bar runs to about 1/3 of the way then drops out & am stuck on the grey screen again.
Tried starting up in safe mode with report Shift-Cmd-V
Lots of tech jargon so am not sure what to look for or how to rectify it (short of reinstalling system discs)
the last 3 lines are as follows (if that's any help)...
fsck_hfs: Volume is journaled. No checking performed.
fsck_hfs: Use the -f option to force checking.
launchctl: Please convert the following to launchd: /etc/mach_init.d/dashboardadvisory.plistYes, I have backed up and deleted old files using target disk mode with an old macbook. It's just the larger files I didn't have enough space and disks for. I really appreciate your help on this as I've never had any mac issues before this so am not really sure what to look for.
-
Can only start up in safe mode
mac g5 running tiger can only start up in safe mode
I already ried the following: zap pram// open-firmware startup// repair permissions// turned off all startup items// disabled automatic login// tried booting from startup disk// started up in single user mode - it said all is fine - but it could not boot// connected via firewire to my other computer and ran disk warrier from my other computer - it said all was fine
STILL - cannot startup normally. can ONLY start up in safe mode. Suggestions pleasebtw - my harddrive checks out fine - no errors
Maybe you are looking for
-
I brought a MacBook air to use outdoors for my small business so I could send paperwork to my HP wireless printer, anyway here in Australia if the police hold something for three months or more its sold at auction provided its not needed for a case
-
Premiere Pro CC Keeps Crashing Upon Launch
I just became a CC member recently and I installed Premiere Pro but every time I launch it, it crashes shortly after opening. I've tried uninstalling and reinstalling but the problem continues. All my other Adobe Apps work fine. Any suggestions?
-
Can't install Firefox 4 on Mac OS 10.4.11. After I download it, the Firefox icon has circle with a crossline in it when I try to install.
-
I have downloaded a file (NYC subway map) and I can find it on my ipod, but I can't seem to get it to open. When I find it, its ends up showing PNG and doesn't give me any other options and doesn't show me a picture. When I open the file on my pc, th
-
Trying to sum up the QHD/scaling problems and solutions
Hello all, For a while I've been thinking about buying the Yoga2 -pro, yet I was (and am) worried about the high resolution making everything too small to work with. Since there are so many posts (some with conflicting stories) in this forum regardi