Starting a Web Server

Ok, here it goes... What I would like to do is turn a busted up Imac into a self contained home web server. My main computer is a PowerMac G3 B&W running OS9 and my frankenstien is an old G3 Imac with OS9 also that I'm going to strip down to just a motherboard, drives, and power supply. I am going to network this all together so that my PowerMac can be in the loop but out of it. I did what little research I could on Classic web file servers but came up with how to do this with SE30s and 128's and a handful of clippings from web pages. There is older Apple software that does all of this but I am unsure about the setup and all where to get it and what it is. Im not looking to host a superduper website just some stuff and grainy pics with basic web page features, email submit maybe and a special area login for those special folks I know... Im not guarding Fort Knox just my PowerMac and the login. I know upgrading would be easier but OS 9 is wonderfully simple and the software is bargain priced..... and I like it to top it off. Any suggestions, sites, hopes, fears, ideas would be helpful towards my venture.
Thank You!

Hi,
The built-in Web Sharing control panel should be useful for certain applications (for example, as in KB article HT2973).
Regarding third-party options, the now free NetPresenz could perhaps be of interest to you. See also this short article about MacHTTP.
Jan

Similar Messages

Problem in starting the web-server after configuring .so on AIX

I am trying to configure a .so file in iplanet fasttrack web server 4.1 on AIX 4.3. I have build the .so file on IBM AIX 4.3. But while starting the web-server it failed to start.It fails when I include the following in obj.conf "Init fn="test-init" config="ConfigFile". While starting web-server I got the following :
server terminated (signal 11): watchdog is restarting it
failure: server initialization failed
Any pointers on this would be helpful.

I got similar errors in the past when the web server process was running in the background. Sometimes shutting down WAS does not work.
Before you start WAS ensure that no java process is running or better try rebooting.

Starting/Stopping Web Server

I am using WebSrvr.Active in my vi to start the web server but when I stop the web server the browser continues to display the front panel. It seems that the setting WebSrvr.Active to false does not stop the server.
Is there a way to check if the server has stopped? Is there a way to disconnect or stop the remote monitoring pragmatically?

According to this KB, the Websrvr.active should stop the server. It also metnoins that only the local machine can access this. I am curious though, does the computer you are accessing the web server with still show updating data even after you have called this property? If so, if you try and refresh the page, does it still stay loaded?
Rob K
Measurements Mechanical Engineer (C-Series, USB X-Series)
National Instruments
CompactRIO Developers Guide
CompactRIO Out of the Box Video

Can not start Secure Web Server

Our Certificate expired while I was on vacation made a new key and csr and sent it off. With the new key,csr and certificate the secure side of our web will not start and just errors out.
Here is the error I get while doing custom config under the security tab
Init: Loading certificate & private key of SSL-aware server secure.lakelandptv.org:443
Here is the error I get while trying to import in general settings under the certificates tab
servermgr_info: [42] [CertificateManager importIdentity:] Error importing certificate: SecKeychainItemImport (err = -25299)
This is on an Xserver running 10.4.11
I believe I have deleted the old certificate out of key chain access but if there is more in Key chain just let me know. Any help will be greatly appreciated.

Do you actually get that HTTP error when you try to start the mobile server. Or do you get that error when the setup executable is running ?
I feel you are mixing up things.
Tell us exactly what you tried, and the error that you got.

Probloms in starting the web server

i am a peoplesoft dba. i am trying to install peoplesoft internet architecture.
the O.S is windows 2000, database is oracle, application server is using Tuxedo
6.5. the web server is weblogic 6.12. i have installed all the components and
am able to log on to the peoplesoft application in 3-tier mode.
now i am trying to set-up the 3-tier web connection. i have created a domain -
VISTDEV. the JSL port is 9000, HTTP port is 80. when i am starting the PIA service
through --- startPIA.cmd under my domain, i am getting the following error:
<Dec 26, 2003 12:24:19 PM CET> <Notice> <Management> <Loading configuration file
.\config\VISTDEV\config.xml ...>
<Dec 26, 2003 12:24:25 PM CET> <Notice> <WebLogicServer> <Starting WebLogic Admin
Server "PIA" for domain "VISTDEV">
<Dec 26, 2003 12:24:44 PM CET> <Notice> <Management> <Application Poller not started
for production server.>
<Dec 26, 2003 12:24:44 PM CET> <Notice> <WebLogicServer> <ListenThread listening
on port 8080>
<Dec 26, 2003 12:24:44 PM CET> <Emergency> <WebLogicServer> <Unable to create
a server socket for port: 443. java.net.BindException: Address in use: JVM_Bind
Perhaps another process is using port 443.>
<Dec 26, 2003 12:24:44 PM CET> <Emergency> <WebLogicServer> <The WebLogic Server
is no longer listening for connections. You should probably restart it.>
<Dec 26, 2003 12:24:44 PM CET> <Alert> <WebLogicServer> <Server shutdown has been
requested by system>
<Dec 26, 2003 12:24:44 PM CET> <Alert> <WebLogicServer> <The shutdown sequence
has been initiated.>
the DOS window closes after that. i am surprised how the port 8080 is coming into
picture.
can you please help in troubleshooting.

Hi,
I suppose you have set the SSL port to 443 however, it looks like port 443 is
already in use by another process.
Regards
Mayur
"blue_jay" <[email protected]> wrote:
>
i am a peoplesoft dba. i am trying to install peoplesoft internet architecture.
the O.S is windows 2000, database is oracle, application server is using
Tuxedo
6.5. the web server is weblogic 6.12. i have installed all the components
and
am able to log on to the peoplesoft application in 3-tier mode.
now i am trying to set-up the 3-tier web connection. i have created a
domain -
VISTDEV. the JSL port is 9000, HTTP port is 80. when i am starting the
PIA service
through --- startPIA.cmd under my domain, i am getting the following
error:
<Dec 26, 2003 12:24:19 PM CET> <Notice> <Management> <Loading configuration
file
\config\VISTDEV\config.xml ...>
<Dec 26, 2003 12:24:25 PM CET> <Notice> <WebLogicServer> <Starting WebLogic
Admin
Server "PIA" for domain "VISTDEV">
<Dec 26, 2003 12:24:44 PM CET> <Notice> <Management> <Application Poller
not started
for production server.>
<Dec 26, 2003 12:24:44 PM CET> <Notice> <WebLogicServer> <ListenThread
listening
on port 8080>
<Dec 26, 2003 12:24:44 PM CET> <Emergency> <WebLogicServer> <Unable to
create
a server socket for port: 443. java.net.BindException: Address in use:
JVM_Bind
Perhaps another process is using port 443.>
<Dec 26, 2003 12:24:44 PM CET> <Emergency> <WebLogicServer> <The WebLogic
Server
is no longer listening for connections. You should probably restart it.>
<Dec 26, 2003 12:24:44 PM CET> <Alert> <WebLogicServer> <Server shutdown
has been
requested by system>
<Dec 26, 2003 12:24:44 PM CET> <Alert> <WebLogicServer> <The shutdown
sequence
has been initiated.>
the DOS window closes after that. i am surprised how the port 8080 is
coming into
picture.
can you please help in troubleshooting.

Starting java web server

i am new to java servlets. i have installed java wev server2.0 on windows 98. i am unable to start it. please someone give me the process to start it.
your help would be very much appreciated.
thank you

I have installed java web server on windows 2000 server machine. I am using the following command to start the server
<server_root>\bin>httpd
but it is display some problem and a message displaying 'shut down the server' in between.please help me.

Unable to start iPlanet web server

Hi, Iam getting the error unable to locate dll "The Dynamic link libraery jvm.dll could not be found in the specified path" when i tried to start the iPlanet web server.Can anybody tell me the reason?this is an urgent one.
Iam getting this error after changing the Global settings in iPlanet web server for Jre/Jdk Path.

Hi,
Look out the below link for your problem :
http://knowledgebase.iplanet.com/ikb/kb/articles/7671.html
As you said you are not able to start the iWS after changing the value of JRE/JDK Path. Then I think you have been use unsupported version of JDK. Kindly revert back to pervious version of JRE/JDK and start the server. To know how to revert back the pervious version of JRE/JDK check the below link.
1.http://knowledgebase.iplanet.com/ikb/kb/articles/5123.html
2.http://knowledgebase.iplanet.com/ikb/kb/articles/4352.html
3.http://knowledgebase.iplanet.com/ikb/kb/articles/5113.html
Hope this helps.
Regards,
Dakshin.
Developer Technical Support
Sun Microsystems
http://www.sun.com/developers/support.

How can i make sure ejb container starts before web server

When starting the application server which one starts first?
Our system requires ejb container to start first.
Currently when i test it, the web container starts before ejb sometimes.
Is there any way to force the ejb container to start up before the web container starts?

What exactly is the dependency you have in your application? The Java EE spec does not
impose any requirements on the order in which the different modules within an .ear are
instantiated.
--ken

Failed to start Apache Web Server

I can not start apach aftre the upgrade of the system
/etc/httpd/conf/httpd.conf:
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used. If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "/etc/httpd"
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:/run/httpd
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
#LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule allowmethods_module modules/mod_allowmethods.so
#LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule cache_socache_module modules/mod_cache_socache.so
#LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule dumpio_module modules/mod_dumpio.so
#LoadModule echo_module modules/mod_echo.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule data_module modules/mod_data.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule request_module modules/mod_request.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule deflate_module modules/mod_deflate.so
#LoadModule xml2enc_module modules/mod_xml2enc.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
LoadModule mime_module modules/mod_mime.so
#LoadModule ldap_module modules/mod_ldap.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule logio_module modules/mod_logio.so
#LoadModule lua_module modules/mod_lua.so
LoadModule env_module modules/mod_env.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
#LoadModule expires_module modules/mod_expires.so
LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule unique_id_module modules/mod_unique_id.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
#LoadModule remoteip_module modules/mod_remoteip.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_fdpass_module modules/mod_proxy_fdpass.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#LoadModule ssl_module modules/mod_ssl.so
#LoadModule dialup_module modules/mod_dialup.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
LoadModule mpm_event_module modules/mod_mpm_event.so
LoadModule unixd_module modules/mod_unixd.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#LoadModule dav_module modules/mod_dav.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule asis_module modules/mod_asis.so
#LoadModule info_module modules/mod_info.so
#LoadModule suexec_module modules/mod_suexec.so
#LoadModule cgid_module modules/mod_cgid.so
#LoadModule cgi_module modules/mod_cgi.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
#LoadModule imagemap_module modules/mod_imagemap.so
#LoadModule actions_module modules/mod_actions.so
#LoadModule speling_module modules/mod_speling.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
#LoadModule rewrite_module modules/mod_rewrite.so
<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User http
Group http
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
<Directory />
AllowOverride none
Require all denied
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/srv/http"
<Directory "/srv/http">
# Possible values for the Options directive are "None", "All",
# or any combination of:
# Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# Note that "MultiViews" must be named *explicitly* --- "Options All"
# doesn't give it to you.
# The Options directive is both complicated and important. Please see
# http://httpd.apache.org/docs/2.4/mod/core.html#options
# for more information.
Options Indexes FollowSymLinks
# AllowOverride controls what directives may be placed in .htaccess files.
# It can be "All", "None", or any combination of the keywords:
# AllowOverride FileInfo AuthConfig Limit
AllowOverride None
# Controls who can get stuff from this server.
Require all granted
</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<Files ".ht*">
Require all denied
</Files>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/var/log/httpd/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you *do*
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and *not* in this file.
CustomLog "/var/log/httpd/access_log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "/var/log/httpd/access_log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://www.example.com/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock cgisock
</IfModule>
# "/srv/http/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
#EnableSendfile on
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf
# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include conf/extra/httpd-autoindex.conf
# Language settings
Include conf/extra/httpd-languages.conf
# User home directories
Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
#Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
Include conf/extra/httpd-default.conf
# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
# Secure (SSL/TLS) connections
#Include conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#</IfModule>
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT
#</IfModule>

There are many topic related to problem with Apache 2.4 upgrade. Search the forum.

Error when starting IPlanet Web Server instance

We are currently using ServletExec 3.0c with IPlanet WebServer, but we have decided to utilise the servlet engine of IPlanet WebServer without much success. We have changed the setting in WebServer Admin to allow Servlets/JSPs to be dealt with by IPlanet, but when we attempt to start the instance we get the following error:
[https-AM]: start failed. (2: unknown early startup error)
[https-AM]: /opt/netscape4/https-AM/start: !/bin/sh: not found
[https-AM]: warning: daemon is running as super-user
[https-AM]: conf_init: Error running init function load-modules: dlopen of /opt/netscape4/bin/https/lib/libNSServletPlugin.so failed (ld.so.1: ns-httpd: fatal: libNSServletLayer.so: open failed: No such file or directory)
[https-AM]: server exit: status 1
The only information we found regarding this error was to add the path of libjvm.so to the LD_LIBRARY_PATH. We did this, but it didn't make any difference.
Thanks in advance
Vince

I got this same error and it turned out to be because one of the developers had changed the line AS_JAVA="/usr/jdk/entsys-j2se" in /opt/sun/appserver/config/asenv.conf
to point to a 1.4.2_10 jre. (/usr/jdk/entsys-j2se was a symlink to /usr/java/jdk1.5.0_04/)
I changed it to an installation of 1.4.2_09 sdk that we had previously installed on their and everything worked fine.
I don't know whether it was because it pointed to a jre as opposed to an sdk or whether the jre was incorrectly installed. (it's a much around box, so everyone's allowed to do pretty much whatever they want to it)
Hope this helps,
Adam

Problem i starting Apache web server

# service httpd start
Got message like :--------------------------
Redirecting to /bin/systemctl start httpd.service
Job for httpd.service failed. See 'systemctl status httpd.service' and 'journalctl -xn' for details.
on checkig log file :: -----------------------------------------------i found this.
# journalctl -xn
-- Logs begin at Sun 2013-01-27 20:38:14 IST, end at Mon 2013-01-28 13:57:43 IST. --
Jan 28 13:56:50 nitk.admin systemd[1]: httpd.service: main process exited, code=exited, status=1/FAILURE
Jan 28 13:56:50 nitk.admin httpd[26019]: AH00548: NameVirtualHost has no effect and will be removed in the next release /etc/httpd/conf.d/aeolus-conductor.con
Jan 28 13:56:50 nitk.admin httpd[26019]: httpd (no pid file) not running
Jan 28 13:56:50 nitk.admin systemd[1]: Failed to start The Apache HTTP Server.
-- Subject: Unit httpd.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/li … temd-devel
-- Documentation: http://www.freedesktop.org/wiki/Softwar … e9d022f03d
-- Unit httpd.service has failed.
-- The result is failed.
Jan 28 13:56:50 nitk.admin systemd[1]: Unit httpd.service entered failed state
Jan 28 13:57:43 nitk.admin nova-compute[1318]: 2013-01-28 13:57:43 1318 AUDIT nova.compute.resource_tracker [-] Free ram (MB): 3377
Jan 28 13:57:43 nitk.admin nova-compute[1318]: 2013-01-28 13:57:43 1318 AUDIT nova.compute.resource_tracker [-] Free disk (GB): 49
Jan 28 13:57:43 nitk.admin nova-compute[1318]: 2013-01-28 13:57:43 1318 AUDIT nova.compute.resource_tracker [-] Free VCPUS: 8
Jan 28 13:57:43 nitk.admin nova-compute[1318]: 2013-01-28 13:57:43 1318 INFO nova.compute.resource_tracker [-] Compute_service record updated for nitk.admin
Jan 28 13:57:43 nitk.admin nova-compute[1318]: 2013-01-28 13:57:43 1318 INFO nova.compute.manager [-] Updating host status
(END)
Can anyone help me to decide, where is the problem???????????
content of the file ; /usr/lib/systemd/system/httpd.service
[Unit]
Description=The Apache HTTP Server
After=network.target remote-fs.target nss-lookup.target
[Service]
Type=notify
PIDFile=/var/run/httpd/httpd.pid
EnvironmentFile=/etc/sysconfig/httpd
ExecStart=/usr/sbin/httpd $OPTIONS -DFOREGROUND
ExecReload=/usr/sbin/httpd $OPTIONS -k graceful
ExecStop=/usr/sbin/httpd $OPTIONS -k graceful-stop
PrivateTmp=true
[Install]
WantedBy=multi-user.target
Last edited by hunter.ashish (2013-01-28 08:32:52)

Could you check if you have this directory? (It can be empty):
/var/run/httpd
permissions should be root:root, mod:755

Problem starting apache web server [SOLVED]

when i start apache manually (sudo /etc/rc.d/./httpd start) i just get a fail, but when i start it through webmin i get the following:
stty: standard input: Inappropriate ioctl for device
Can someone tell me how i can fix this, or if it is too hard to fix, give me the name of the next best http server available?

i had problems with apache too, but then i just did some changes:
in httpd.conf i changed user from nobody to httpd;
then added to system user httpd via adduser httpd in group nobody and it worked well

Problem starting Tomcat web server in Ubuntu.

Hi every one,
I use Ubuntu OS.I have installed J2sdk.I want to start tomcat webserver but whenever i start the server I get an error as
'/usr/share/tomcat/bin/catalina.sh: line 41: setJava: No such file or directory'
I tried removing the line, to find out the cause of that error.When I removed line 41 , it showed JAVA_HOME variables not set.
I have set JAVA_HOME varible as
'/usr/lib/j2sdk1.5-sun/bin/javac/usr/lib/j2sdk1.5-sun/bin/'
line 41 is '. setJava --devel Java2'
Could anyone help me to solve this issue?
And Thanks in advance
-Jegan

I use Ubuntu OS.I have installed J2sdk.I want to start tomcat webserver but whenever i start the server I get an error as
'/usr/share/tomcat/bin/catalina.sh: line 41: setJava: No such file or directory'
I tried removing the line, to find out the cause of that error.When I removed line 41 , it showed JAVA_HOME variables not set.
I have set JAVA_HOME varible as
'/usr/lib/j2sdk1.5-sun/bin/javac/usr/lib/j2sdk1.5-sun/bin/'
line 41 is '. setJava --devel Java2'
Could anyone help me to solve this issue?
And Thanks in advance

Problem in starting java web server 2.0

I have java webserver2.0. When i tried to start it manually by typing httpd command on command line.It gives me some error of memory(some hexa codes and the message "could not 'write' & some hexa codes again"). Then i tried to start it by givig jservsvc.exe which gave same problem. This problem persists on both o.s Win 2000 and win 98.
Please help me on that.
Thank You

i dont know that this will work but try it
search "httpd.exe" or bat file in ur javweserver2.0 folder
and direclty double click it
or check wether its already running as a service

IPlanet 7.0.15 on Red Hat - Problems starting web server

I completed the installation of iPlanet 7.0.15 on Red Hat Linux 5. The Admin server starts fine, however when I attempt to start the web server I get the following error:
Oracle iPlanet Web Server 7.0.15 B04/19/2012 21:52
catastropheinfo: CORE3282: stdout: Error occurred during initialization of VM
info: CORE3282: stdout: Unable to load native library: /opt/Apps/libjava.so: cannot open shared object file: No such file or directory
: CORE4005: Internal error: unable to create JVM
failure: server initialization failed
I am not sure what is causing this error? I selected the default, "Install JDK that is provided with iPlanet" and it is located in directory:
/opt/Apps/Oracle/webserver7/jdk
I am not sure why the native library in /opt/Apps/libjava.so is being referenced.
I have tried several things including installing Java in /usr/bin from a download from Oracle. It appears to work just fine.
I have installed and reinstalled - same problem.
Any ideas?

Okay this one turned out to be fairly simple. It was a permissions issue. One of my top level directories (/opt/Apps/Oracle) did not have world execute permissions. Once I changed the directory permissions the web server came up fine. It only took me 5 days to find this and fix it.

Starting a Web Server

Similar Messages

Maybe you are looking for