Startup screen with apple logo and grey loading bar, then unexpectedly shuts down
Hey, I have a MacBook Pro from 2010 I believe with iOS Maverick installed. (MacKeeper is also on there, which I just found out is apparently malware)
So three days ago I was watching Netflix, the image froze, but the audio kept going. Figured my internet was slow, so I waited a little, nothing happened. pressed escape to leave the full screen mode, but nothing happened. None of the keys would do anything, not even the sound or brightness keys. So I did a force shut down by holding down the power button.
I waited a little, then decided to turn it back on. Start up sound played, white screen with grey apple logo and loading gear appeared together with a grey loading bar. I figured that this meant it had to repair something. But after about a minute or two it just went to a black screen/ shut down. I left it off for a day, tried it again, same thing. Next day I tried booting it up while holding the shift key to do the safe boot (I knew it wouldn't work since I already had the grey loading bar anyways), same thing happened.
Any suggestions? (note: I thought I had posted this yesterday, but apparently I didn't even register as a user, weird. So if this gets posted twice, I apologize)
If your disk cannot be repaired, your only options are to call the disk dead and order a new one or to try and erase and reformat the disk and try to install a system on it.
The latter is just something you can try - I doubt that it will work.
Boot into your Recovery partition once again and select Disk Utility. You should see your boot volume (usually named "Macintosh HD") in the left column of disks. Select the Erase tab and format the disk using "Mac OS Extended (Journaled)". If the disk will format, then you can go back to the main Recovery screen and try installing OS X.
If that doesn't work - and you'll probably know when trying to format the drive - you'll need a new drive.
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.3, 16GB RAM, 960GB SSD, 27” Apple Thunderbolt Display
Similar Messages
-
When turning on my mac book pro it displays a screen with apple logo and begins loading a loading bar, after this continues to show loading circle however has been like this all day still no different. Tried turning it on and off however still same!
... then run Disk Utility, Repair Disk.
Also:
Resolve startup issues and perform disk maintenance with Disk ...
Mac troubleshooting FAQ: start-up woes
How To Fix Common Mac Startup Problems
Mac Stalls on Gray Screen at Startup - Troubleshooting Mac Startup ... -
imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black
Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
I disconnected my iPad unconsciously while it was updating ios 7.0.4 and it just stuck on that screen showing apple logo and a loading bar that just won't move on what to do now ????
It's not uncommon for it to not work the first time and sometimes, you have to try it a few times. Turn off your antivirus software and your firewall while you are trying to restore the iPad. Enable them again after you restore.
If that still won't work, post back with detailed information as to what exactly does happen as you go through the process. -
Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help
Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support
-
Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data. -
I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?
Maybe this might help.
http://support.apple.com/kb/TS2570 -
in the middle of my last update it stopped updating in the because of an unknown source, and now my screen on my iphone is frozen with the apple logo and a loading bar. Help??
Unknown "source"? Do you mean unknown "error" followed by a number?
http://support.apple.com/kb/TS3221
Follow the instructions in the article. When you connect your phone again, you may have to press both the home and sleep/wake buttons until the Apple logo reappears, then continue pressing the home button until iTunes detects the phone in recovery mode. -
Start up screen stuck on grey screen with apple logo and spinning gear
Start up screen is stuck on grey screen with apple logo and spinning gear. What should I do?
See this thread with dominic23’s suggestions: https://discussions.apple.com/thread/5783326?tstart=0
-
Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao. -
My iMac wont go past the grey screen with Apple Logo and question mark a caution mark
My iMac wont go past the grey screen with Apple Logo and question mark a caution mark
You may find this support article helpful:
http://support.apple.com/kb/TS2570
Ciao. -
My touch is frozen on a black screen with the apple logo and a load bar, nothing works, tried resetting and everything, any suggestions?
In that case....if you have Apple Care, give support a call - otherwise, walk it into the nearest Apple Store.
Good luck. -
TS2570 Mac will not start up after software up date, just screen with Apple logo and spinning icon?
Mac will not start up after software up date, just screen with Apple logo and spinning icon? I have tried safe start up, unplugged all other cables, no luck?
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update. -
i disconnected my iphone 4 while it was updating and now its frozen, the screen is showing a apple logo and a loading bar which has been for 9hrs now. please help
It's not uncommon for it to not work the first time and sometimes, you have to try it a few times. Turn off your antivirus software and your firewall while you are trying to restore the iPad. Enable them again after you restore.
If that still won't work, post back with detailed information as to what exactly does happen as you go through the process. -
Won't turn on white screen with apple logo and spinning disc
Mac book air won't boot up just has a white screen with apple logo and spinning disc have tried all the startup multiple key pushes , I think
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Maybe you are looking for
-
Is there a way to block invitation notifications?
My company uses Google calendar. I have a personal calendar, and then everyone has access to the companywide calendar as well. This allows us to see every meeting happening in the company. When we create new events, we create them in the companywide
-
What is my serial number. the original version?
what is my serial number? The original version? the most recent upgrade? for photoshop.
-
MacBook Pro OS X 10.8.4 doesn't detect DVI display with clamshell closed
Just got a Dell S2340M monitor, connected by DVI. Works OK (while displays 'mirrored' - didn't have to do that with VGA) while clamshell is open, but the Mac isn't seeing it with the clamshell closed. Tried rebooting, adjusting display settings, et
-
2 devices, "contacts" "my info" question
I have an iPad and wife has iPhone. We are using one iCloud account to share contacts, calendar, reminders, etc... And then separate sub accounts on iCloud for email only. The problem is under Settings>Mail, Contacts, Calendars>Contacts>My Info>? I p
-
DTW BP Bill to Address importing Problem
Hi All, I am using SAP Business One 2005B and during import of Business Partner through DTW I am not able to import bill address . Can anyone let me know from where i can put the ship adress in csv file format.