Status:\t10.0000 SUPPLY MEMORY ERROR + cannot install printer

Hi I have an HP Laserjet P1102w printer. I changed my router, and changed my laptop and now am not able to install the printer on the new laptop and router.
I have tried installing from the HP smart install program via USB cable. When i do this I get an error message saying that the installation failed and advising me to turn off the printer, turn it on again and try again.
I have tried resetting the printer to the default settings, then printing a test page and using the supplied IP address to access the printer. An error message says:
Status: 10.0000 SUPPLY MEMORY ERROR
I have tried ignoring this and going to the HP Smart Install Tab and installing the printer that way. When i did this I get a similar error message to before saying that the installation failed and advising me to turn off the printer, turn it on again and try again.
Could someone please advise me on what to do? Should I focus on trying to get the printer installed, then try to fix the supply memory error or fix the supply memory error and then try to install the printer? I'm a bit loathed to buy a new toner cartridge, if after doing this the printer may still fail to install.
Thanks in advance,
Paul
This question was solved.
View Solution.

Very good information. Since this printer is having such a hard time reconnecting try resetting the printer first. I have provided a link on how to restore this printer to factory defaults. I had a similar problem with this printer until I installed a very recent firmware update. This is how I finally was able to get it to install and connect:
Clicked on the Software and Drivers tab at www.hp.com/support and typed in my printer name (Laserjet P1102w) and pressed the enter key. Next I selected my operating system (you will need to know if your computer's system type is 32 bit or 64 bit or I would provide a link).
Under the Driver and Product installation I installed the HP Laserjet Full Feature Software and Drivers and proceeded to install it using the USB to wireless configuration.
After the test page printed, the printer disconnected from the network so with the USB cord still attached, I went to the same download page and installed the most recent firmware update: Version 20130213 which went very well I might add.
Next, I went to the Start button and selected All Programs>>HP>>HP Laserjet Professional P1100 series>>Wireless Configuration and finished getting my printer connected back to my network.
I strongly suggest the firmware update. I hope this information helps you out. Try the steps above and if it doesn't work let me know. I will look at the error message once you are able to get it installed. It may be that when you restore the printer to factory defaults you will also want to reboot the computer in case you are running low on available memory, hence the error message.
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

Similar Messages

I have a new hp 2050 printer and received a 10.0000 supply memory error message. what does this mean

I have a new hp 2050 printer and received a 10.0000 supply memory error message. Can anyone tell me what this means and how to fix it?

mickeymackey, this error looks similar to a related error code that I found for laserjets. Here is a summation of that error code:
http://goo.gl/W7dP6
This describes the problem as being a cartridge error, in which case I would follow the instructions in this document and see if that resolves the issue:
http://goo.gl/h6hWz
that does not resolve the issue, then I would recommend performing a hard reset of the printer. This would involve unplugging the printer for thirty seconds from both the back of the unit as well as from the outlet it is plugged into and then plugging the machine back in and powering it on.
A few additional questions are: Is this printer plugged into a surge protector, wall outlet or battery backup? The ink you are using, are they original HP cartriges or have they been refilled before?
Let me know!

Error Message 10.0000 Supply memory Error

What does this mean?
How can I resolve?

mickeymackey, this error looks similar to a related error code that I found for laserjets. Here is a summation of that error code:
http://goo.gl/W7dP6
This describes the problem as being a cartridge error, in which case I would follow the instructions in this document and see if that resolves the issue:
http://goo.gl/h6hWz
that does not resolve the issue, then I would recommend performing a hard reset of the printer. This would involve unplugging the printer for thirty seconds from both the back of the unit as well as from the outlet it is plugged into and then plugging the machine back in and powering it on.
A few additional questions are: Is this printer plugged into a surge protector, wall outlet or battery backup? The ink you are using, are they original HP cartriges or have they been refilled before?
Let me know!

Supply memory error on M201dw what does it mean?

I just purchased a HP LaserJet Pro 201dw and when I plugged it in I god a Supply memory Warning. What does this mean?

Hi @JJprinter ,
I understand that you are getting a supply memory error after setting up the new printer. I will certainly do my best to help you.
Make sure all the orange packing material and the seal is removed from the toner and any packing material inside the printer. Here is a picture of the toner and the orange packing material that needs to be removed.
I have provided the hardware installation guide that you can take a look at. LaserJet Pro M201, M202.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

What is a 10.1000 supply memory error

what is 10.1000 supply memory error?

That seems to indicated a toner or ink cartridge problem for a HP printer. HERE IS A THREAD that disusses the error and ways to correct it. give it a read to see id what is dicussed helps.

Libtool: install: error: cannot install

I seem to be having all the luck recently. Any suggestiosn for this one?
test -z "/opt/qgis/lib/qgis" || mkdir -p -- . "/var/abs/gis/qgis/pkg/opt/qgis/lib/qgis"
/bin/sh ../../libtool --mode=install /bin/install -c 'grassplugin.la' '/var/abs/gis/qgis/pkg/opt/qgis/lib/qgis/grassplugin.la'
libtool: install: error: cannot install `grassplugin.la' to a directory not ending in /usr/lib/qgis
make[4]: *** [install-pluginLTLIBRARIES] Error 1
Obviously it is the /usr part that is killing it

Try running libtoolize -f on the source as first thing to do in the build() function in the PKGBUILD. I've seen many broken libtool scripts in tarballs around, especially on gnome ones (packages using libblabla.14 instead of libblabla.so.14 for example )

Printer error-supply memory error

hi i am having HP 5550 Dn printer and recently it is giving error 100002 supply memory error.
how this can be solves i am not able to get print

Here is a link that can help you troubleshoot the "Supply Memory Error":
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02484074&tmp_task=solveCategory&cc=us&dlc=en&la...
If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

What is a supply memory error 10.1000? How can I fix it? My printer won't scan nor print.

My Laser Jet M1212nf MFP still copies, but everytime I try to print or scan a document it doesn't work and it shows a supply memory error on the display. I already tried to switchof and uplug the printer, but the problem still persits. Can anybody help me???
This question was solved.
View Solution.

Just fixed this on yet another Laserjet 2600dn....
Remove the affected cartridge. Look at where the chip on the cartridge hits the reader at the rear of the machine. There are two triangular 'wires' which hit the chip.
They should both be raised proud of their mount. In all cases of this error which I have dealt with (I'm a reseller) one or both have been pushed into the mount and are failing to spring out when the cartridge is removed.
This prevents the chip being read.
The solution? Grab them and gently pull them proud again so that the inserted cartrdige makes firm contact with them.
Problem solved! Hope this helps at some people experiencing this issue.

HP4501e "print spooler off" error after installing printer update

Motorola Android OS, getting "print spooler off" error after installing printer update... have rebooted both printer and phone to no avail... any help ideas?

Loralee,
?? I am sorry the computer is not working. I don't work for HP and cannot comment on lawsuits or other calamities.
If the notebook worked prior to an update -- and this is an entirely different can of worms and problems -- and you think that there is any chance the notebook is just in some sort of "tangled" state and not completely hosed for some reason, you can try the following non-lethal device reset:
Create a Restore Point: Create a Restore Point – Win7 OR Create a restore point Win8
If you are using a Notebook:
Close all your programs and shut down the computer
Disconnect everything (little Unifier for the keyboard / external mouse can stay)
Perform the Hard Reset for your notebook model
Boot the computer and log in
Reminder: Hard Reset is just a device Reset. The procedure does not wipe out your files nor does it destroy your Windows setup in any way. This type of reset "clears the cobwebs". Depending on the root cause of the problem, this procedure can fix a variety of computer glitches.
This does not fix severe Operating System errors -- it is just a device reset. It can fix minor problems that updates sometimes cause.
============================================================================
I am sorry you are having so much trouble.
Other help:
HP Mobile Printing
You can call HP for help --
Contact HP – USA - Phone Assistance
List of
HP tech support/ Customer Service Phone Numbers – Some English Speaking Countries
Warranty Required – USA and Canada
USA – Contact HP // Self-Help – Email - Chat
Happy New Year, Loralee! I know it seems to be getting off to a rocky start!
Click the Kudos Thumbs-Up to show you appreciate the help.
I am pleased to provide assistance on behalf of HP. I do not work for HP.
Click Accept as Solution when the Answer provides a Fix or Workaround!
Kind Regards,
Dragon-Fur

Error while installing printer software for HP Photosmart Plus 209a-m on Windows 8.1 64 bit OS

I am getting below error while installing printer software of HP Photosmart Plus 209a-m on Windows 8.1 64 bit OS. Can you please help me resolve this error? Thanks in advance.

Hi tarunkw,
Follow the steps below and check if that resolve the issue:
1. Open Mcafee software, from the Virus and Spyware Protection section click on Schedule and run scans. Click on Real time scanning and then on Turn Off. select till I restart the PC and confirm by clicking the Turn Off button.
Now try reinstalling the HP Software and check if the installation goes as expected.
If the issue persists continue following the next steps below:
2. Open the run dialog by clicking both the Windows key and the R key on your keyboard. Type %windir% and click on OK.
3. Type hpoins*.dat into the top search bar, if there are any results rename the extention into old instead of dat. (e.g. hpoins1.old)
4. Type hpwins*.dat into the top search bar, if there are any results rename the extention into old instead of dat. (e.g. hpwins1.old)
5. Launch the Run dialog by clicking both the Windows key and the R key on your keyboard. Type MSIEXEC /UNREGISTER into the Run dialog and click on OK.
6. Launch the Run dialog by clicking both the Windows key and the R key on your keyboard. Type MSIEXEC /REGSERVER into the Run dialog and click on OK.
7. Run the installation file and check for any difference.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Help with error cannot install any apps

can any help solve my error issue. I cannot install any apps. and apman says i have no catalogues. but i do anf i even get ! icon saying i have updates.
BusyBox v1.10.2 (Debian 3:1.10.2.legal-1osso30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ $ sudo gainroot
Root shell enabled
BusyBox v1.10.2 (Debian 3:1.10.2.legal-1osso30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
/home/user # apt-get upgrade
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run `apt-get -f install' to correct these.
The following packages have unmet dependencies:
mp-fremantle-community-pr: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
status-area-orientationlock-applet: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
E: Unmet dependencies. Try using -f.
/home/user # apt-get -f install
Reading package lists... Done
Building dependency tree
Reading state information... Done
Correcting dependencies... Done
The following packages were automatically installed and are no longer required:
python-xml python-facebook libqt4-translations
Use 'apt-get autoremove' to remove them.
The following extra packages will be installed:
hildon-desktop
The following packages will be upgraded:
hildon-desktop
1 upgraded, 0 newly installed, 0 to remove and 16 not upgraded.
6 not fully installed or removed.
Need to get 0B/235kB of archives.
After this operation, 20.5kB of additional disk space will be used.
Do you want to continue [Y/n]? y
(Reading database ... 34004 files and directories currently installed.)
Preparing to replace hildon-desktop 1:2.2.140-1+0m5 (using .../hildon-desktop_1%3a2.2.142-11_armel.deb) ...
Unpacking replacement hildon-desktop ...
dpkg: error processing /var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb (--unpack):
trying to overwrite `/usr/share/gconf/schemas/hildon-desktop-keys.schemas', which is also in package modified-hildon-desktop
Errors were encountered while processing:
/var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
/home/user # apt-get autoremove
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run `apt-get -f install' to correct these.
The following packages have unmet dependencies:
mp-fremantle-community-pr: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
status-area-orientationlock-applet: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
E: Unmet dependencies. Try using -f.
/home/user #
BusyBox v1.10.2 (Debian 3:1.10.2.legal-1osso30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ $ sudo gainroot
Root shell enabled
BusyBox v1.10.2 (Debian 3:1.10.2.legal-1osso30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
/home/user # apt-get upgrade
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run `apt-get -f install' to correct these.
The following packages have unmet dependencies:
mp-fremantle-community-pr: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
status-area-orientationlock-applet: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
E: Unmet dependencies. Try using -f.
/home/user # apt-get -f install
Reading package lists... Done
Building dependency tree
Reading state information... Done
Correcting dependencies... Done
The following packages were automatically installed and are no longer required:
python-xml python-facebook libqt4-translations
Use 'apt-get autoremove' to remove them.
The following extra packages will be installed:
hildon-desktop
The following packages will be upgraded:
hildon-desktop
1 upgraded, 0 newly installed, 0 to remove and 16 not upgraded.
6 not fully installed or removed.
Need to get 0B/235kB of archives.
After this operation, 20.5kB of additional disk space will be used.
Do you want to continue [Y/n]? y
(Reading database ... 34004 files and directories currently installed.)
Preparing to replace hildon-desktop 1:2.2.140-1+0m5 (using .../hildon-desktop_1%3a2.2.142-11_armel.deb) ...
Unpacking replacement hildon-desktop ...
dpkg: error processing /var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb (--unpack):
trying to overwrite `/usr/share/gconf/schemas/hildon-desktop-keys.schemas', which is also in package modified-hildon-desktop
Errors were encountered while processing:
/var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
/home/user # apt-get autoremove
Reading package lists... Done
Building dependency tree
Reading state information... Done
You might want to run `apt-get -f install' to correct these.
The following packages have unmet dependencies:
mp-fremantle-community-pr: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
status-area-orientationlock-applet: Depends: hildon-desktop (>= 1:2.2.142-11) but 1:2.2.140-1+0m5 is installed
E: Unmet dependencies. Try using -f.
/home/user #
cheers for any assistance

k i went to maemoder and tried to remove hildon via restore (strange) then entered the commonds u gave but this is what i got
o30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ $ root
BusyBox v1.10.2 (Debian 3:1.10.2.legal-1osso30+0m5) built-in shell (ash)
Enter 'help' for a list of built-in commands.
Nokia-N900:~# apt-get install hildon-desktop
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
python-xml python-facebook libqt4-translations
Use 'apt-get autoremove' to remove them.
The following packages will be upgraded:
hildon-desktop
1 upgraded, 0 newly installed, 0 to remove and 16 not upgraded.
6 not fully installed or removed.
Need to get 0B/235kB of archives.
After this operation, 20.5kB of additional disk space will be used.
(Reading database ... 34004 files and directories currently installed.)
Preparing to replace hildon-desktop 1:2.2.140-1+0m5 (using .../hildon-desktop_1%3a2.2.142-11_armel.deb) ...
Unpacking replacement hildon-desktop ...
dpkg: error processing /var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb (--unpack):
trying to overwrite `/usr/share/gconf/schemas/hildon-desktop-keys.schemas', which is also in package modified-hildon-desktop
Errors were encountered while processing:
/var/cache/apt/archives/hildon-desktop_1%3a2.2.142-11_armel.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
Nokia-N900:~#
why did it not work?

Out-of-Memory Error while Installing AS 1.0.2.2.0

I am getting the following error while Installing Application Server 1.0.2.2.0. The progress bar shows 100% at this time and this screen hangs there.
The hardware config of the machine are
Windows 2000 Professional
256Ram
Processor AmdDuron 500
Hard disk 20GB
Note: The Oracle 9i database is on another machine.
java.lang.OutOfMemoryError
     at java.lang.String.<init>(Compiled Code)
     at oracle.sysman.oii.oiip.oiipg.OiipgEnvironment.getEnv(Compiled Code)
     at oracle.sysman.oii.oiix.OiixSpawner.unsetJavaHome(OiixSpawner.java:638)
     at oracle.sysman.oii.oiix.OiixSpawner.beginExecute(OiixSpawner.java:443)
     at oracle.sysman.oii.oiix.OiixSpawner.beginExecute(OiixSpawner.java:572)
     at Spawn.doSpawn(Spawn.java:92)
     at Spawn.installAction(Spawn.java:48)
     at oracle.sysman.oii.oiis.OiisCompActions.doActionWithException(Compiled Code)
     at oracle.sysman.oii.oiis.OiisCompActions.doActionImpl(Compiled Code)
     at oracle.sysman.oii.oiis.OiisCompActions.doAction(Compiled Code)
     at CompActions.doActionP3Spawn4(CompActions.java:350)
     at CompActions.stateChangePhase2Actions(CompActions.java:287)
     at oracle.sysman.oii.oiic.OiicInstallActionsPhase$OiilActionThr.run(Compiled Code)
     at oracle.sysman.oii.oiic.OiicInstallActionsPhase.executeProductPhases(Compiled Code)
     at oracle.sysman.oii.oiic.OiicInstallActionsPhase.doInstalls(OiicInstallActionsPhase.java:1398)
     at oracle.sysman.oii.oiic.OiicInstallActionsPhase$OiInstRun.run(OiicInstallActionsPhase.java:2015)
     at java.lang.Thread.run(Compiled Code)

The 10g and later drivers trade memory for performance. They use much more memory than the 9i drivers, but are much faster. If you look at the JDBC FAQ here on OTN there is some more info on where the memory is going. The stack trace you posted is what I would expect to see from buffer allocation described in the FAQ.
Douglas

Photoshop keeps on getting out of memory error after installing Premier Pro

I just upgrade my CS to CC. Yesterday I installed Photoshop and did my work without any problem but today after installing Premier and After Effect, I keep on getting out of memory error when I'm working even though I don't have any other application running accept photoshop alone. The file I'm working on is a small file, iphone plus size interface. Basically I can open the file, add blur effect and try to type text I will get photoshop telling me that my system is out of memory. Restarting photoshop give the same problem, restarting my computer give the same problem, ie do one thing and next will give memory not enough.
I don't think my system is slow as it is workstation with dual processor and 12 gig of ram, windows 7 64bits 1gb dedicated memory for graphic card.
I uninstall Premier and After Effect and suddenly the problem go away. Photoshop work as per normal. I didn't have the time to reinstall premier again but will try to do it tonight or tomorrow
Anyone experience such problem before?

When you get that error leaver the error showing and use something the can show you how much free disk space there is left on Photoshop scratch disk. It may be a problem with scratch storage space not ram storage space. I see Photoshop use much more scratch space the ram. I have seen Photoshop using less than 10GB of ram on my machine leaving 30GB of free ram on my system unused while using over 100GB of scratch space.

Application catalog error - cannot install or request software.

Hi All,
I have installed SCCM 2012 SP1 and configured SCCM APP catalog, i am able to browse the portal from a client machine, the portal shows the application which are deployed but when i send a request for the application and after administrators approval
the the app catalog is not able to download the application and the portal shows
"cannot install or request software error message"same is happening with the application without request policy.
What i have tried :-
1. Adding the App catalog URL to the LOCAL Intranet zone.
2.Reinstallation of Application catalog.
But it shows the same error please help.

thanks for replying,
Seems like it was an MP issue, my MP was not working.
I did the following things :-
1. Remove App Catalog roles.
2. Uninstalled Management Point.
3. Uninstalled IIS.
4. System Restart.
5. Installed IIS.
6. Installed MP.
7. Installed App catalog roles.
Now, it's working.
Thanks,
Pranay.

Memory Error when installing labview 6.1

I had labview 6.0, 6.1 and RT installed on my PC (windows 2000). I tried to install application builder but I got Error that I have no labview installed, so I tired to uninstall RT, but I was abe to. Then I found out that I can't install or uninstall any of the Labview versions. So I went and deleted the whole NI directory, all the keys related to NI in the registry file, and Labview.ini. Now I'm trying to install labview 6.1, but I'm getting memory error and setup terminates. What can I do!
Attachments:
LB_Setup_Error.gif ‏36 KB

First, I recommend contacting NI support at ni.com/ask and starting an incident report.
Second, I recommend either restoring your registry from backup, or wiping your system and starting over. I know it doesn't sound like fun, and it isn't, but it is probably the only way now you can guarantee a good clean registry. Alternatively, go through the registry again and make sure all National Instruments and LabVIEW entries are deleted.
In the future, and I make this recommendation to everyone, you should, as a safe practice, make a backup of your registry before you install anything, and also periodically. Archive these and label them with the list of programs installed, or with any new programs that have been installed.
The Windows registry is obsolete,
and complete hopeless when it comes to a stable system. There is no automated backup of the registry to my knowledge. The registry is the biggest source of problems with Windows, followed of course by DLLs (everyone has their own version, and noone's is alike, much less works right.) The registry can be backed up by using "Export" from the regedit program. Backups can be restored with the "Import" function in regedit of course.
Good luck.

Status:\t10.0000 SUPPLY MEMORY ERROR + cannot install printer

Similar Messages

Maybe you are looking for