Steps to clean shut down replicationa and again re-startup process.
Hi Folks,
I have implemented simple unidirectional repalication without Data pump in below setup:
Oracle RAC 11gr2 , 2 nodes
ASM
GG 11.1
I have shut down extract, Managre and replicate process on source and target after succesfull testing of replication.
Now I want to go for real implementation and cutover date. for that I will perform
1. initial load and
2. replication
Will there be any problem if I re-start the replication again after 3 - 4 days ?
What are the steps need to follow ?
Thanks in advance.
Regards,
Edited by: LazyDBA11g on Aug 23, 2012 2:08 AM
Hi,
I assume , you want to stop all the replication process which was created for testing purpose then you want to use the same process for original tables. if i'm correct try the below steps. i think this like a new confguration setup.
1. Stop all the process on source and target environments.
2. Start the initial load from source to target (as per your initial load method.) (make sure there is no online transactions on the replication tables otherwise choose the SCN initial load method. then you have follow different steps. )
3. after completed the initila load process, make sure there is no transactions during initial load process and reconfirm both the databasein sync mode.
4. recheck the configuration parameters all the schema and table names are updated for orinal tables.
5. alter the extract process - alter extract <extname> tranlog , begin now. or you can start extracrt with particular timestamp.
6. alter the replicat process on target - alter replicat <repname> begin now
7. Now start the extract and check the stats whether changes are captured or not , if everthing ok
8. Start the replicat process.
Hopefully this will help you if i understtod your question properly.
Similar Messages
-
Hello All,
I have a 15" i7 Macbook Pro from early 2011. The past few weeks, it has been getting increasingly difficult to get on my computer. It takes the mac laptop two or three tries to boot successfully. It would turn on, show gray screen, shut down, turn on again, show gray screen, shutdown, and then turn on, show gray screen, before it can finally get to the dark gray log-in screen. Even when I finally get logged in to start working, thinking it would be okay now, it shuts down randomly.
I've ruled out the possibility of a software problem because I've just done a clean re-install of Mac OS X Mavericks on my computer just yesterday.
I did upgrade the RAM recently, about a month and a half ago, from 4GB to 16GB, I went to the apple store four days after that upgrade to have them do a hardware test, and clean the inside of my laptop, which helped with previous heat issues. When they did the hardware test, the hardware was all registered as fine from their system.
I've tried resetting the SMC, PRAM, and doing the internet recovery hardware test, but to no avail. I thought I could at least find out what parts needed to be replaced from the hardware test but it seems that when the hardware test is almost finished, the computer just shuts down, So I am unable to see the results.
My computer is also having battery issues, under battery condition, it says "replace now," parts have been ordered, waiting for arrival. But if the battery health is low, it should still boot up fine, it would just hold a significantly less charge.
Could this be a hard drive issue?
Has anyone had similar symptoms and how was it resolved?
Does anyone know what I can do to alleviate this issue?
I haven't had time to take it to Apple because I'm currently taking a 21 credit semester academically. I'm an art and design student so my computer is basically the bane of my existence. Help! Any constructive advice is welcomed!
Thank you so much for your input!
-Christina C.Problem description:
The Hard Disk is failing.
EtreCheck version: 2.0.11 (98)
Report generated November 4, 2014 at 7:59:28 AM EST
Hardware Information: ℹ️
MacBook Pro (15-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,2
1 2.2 GHz Intel Core i7 CPU: 4-core
16 GB RAM Upgradeable
BANK 0/DIMM0
8 GB DDR3 1600 MHz ok
BANK 1/DIMM0
8 GB DDR3 1600 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 512 MB
Color LCD 1440 x 900
AMD Radeon HD 6750M - VRAM: 1024 MB
System Software: ℹ️
OS X 10.9.5 (13F34) - Uptime: 0:3:43
Disk Information: ℹ️
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
HDV4 (disk0s2) / [Startup]: 749.30 GB (712.10 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
MATSHITADVD-R UJ-898
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Application Support/Avast/components/fileshield/unsigned
[loaded] com.avast.AvastFileShield (2.1.0 - SDK 10.9) Support
/Library/Application Support/Avast/components/proxy/unsigned
[loaded] com.avast.PacketForwarder (1.4 - SDK 10.9) Support
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.avast.userinit.plist Support
Launch Daemons: ℹ️
[invalid?] com.adobe.SwitchBoard.plist Support
[loaded] com.avast.init.plist Support
[loaded] com.avast.uninstall.plist Support
[loaded] com.avast.update.plist Support
[invalid?] com.perion.searchprotectd.plist Support
User Launch Agents: ℹ️
[invalid?] com.avast.home.userinit.plist Support
[loaded] com.google.keystone.agent.plist Support
[invalid?] com.jdibackup.ZipCloud.autostart.plist Support
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
AdobePDFViewer: Version: 10.1.1 Support
QuickTime Plugin: Version: 7.7.3
JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
Default Browser: Version: 537 - SDK 10.9
User Internet Plug-ins: ℹ️
TroviNPAPIPlugin: Version: 1.0 - SDK 10.9 Support
Google Earth Web Plug-in: Version: Unknown
Safari Extensions: ℹ️
Avast Online Security
Trovi Search for Safari
3rd Party Preference Panes: ℹ️
None
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
16% mds
7% WindowServer
1% loginwindow
1% fontd
1% com.avast.daemon
Top Processes by Memory: ℹ️
120 MB com.avast.daemon
86 MB Google Chrome
52 MB Finder
52 MB WindowServer
41 MB Google Chrome Helper
Virtual Memory Information: ℹ️
13.45 GB Free RAM
1.34 GB Active RAM
944 MB Inactive RAM
1.43 GB Wired RAM
1.11 GB Page-ins
0 B Page-outs -
hi, 3 weeks ago i just got my iphone4 for and then i upgraded it to iOS5..am just wondrin', does changing or upgrading the OS causes the phone to shuts down automatically and turn on again? thanks.. =)
How long are you leaving it on the charger?
Are you connecting it directly to an electrical outlet or trying to charge via USB? USB may not provide enough power to adequately charge the device if the battery is that low.
If none of that helps, then the only option would be a warranty replacement as either the battery or system board is bad. -
I was surfing online when suddenly my mac just freeze. So i had forced shut down it and turned it on again but then the folder with questionmark icon shows up. And i pressed (option key) to go to the utility but i cant find my startup disk anywhere!
Well, if the internal hard drive is no longer readable, there's pretty much nothing anyone here can do about it. There are no magic words that will fix a hardware problem.
Make an appointment at the genius bar and have it looked at. -
Hello, Currently we are seeing this issue with a couple of our Lenovo T420s laptops with a Solid State Drive. ruffly about 10 or so. The Reboots happen randomly and do not create a dump file. We have contacted Lenovo and they are
not sure why its happening. Since this Crash I set it for Minidump this did not work my next steps will be to Disable Automatic restart on System Failure to see if it brings anything up. I am also looking at using Procmon to dump to a file as well.
If anyone has any other ideas please let me know.
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.
+ System
- Provider
[ Name] Microsoft-Windows-Kernel-Power
[ Guid] {331C3B3A-2005-44C2-AC5E-77220C37D6B4}
EventID 41
Version 2
Level 1
Task 63
Opcode 0
Keywords 0x8000000000000002
- TimeCreated
[ SystemTime] 2012-02-01T00:02:48.677610900Z
EventRecordID 8270
Correlation
- Execution
[ ProcessID] 4
[ ThreadID] 8
Channel System
Computer LR8K6TLC.cntr.thrivent.corp
- Security
[ UserID] S-1-5-18
- EventData
BugcheckCode 0
BugcheckParameter1 0x0
BugcheckParameter2 0x0
BugcheckParameter3 0x0
BugcheckParameter4 0x0
SleepInProgress false
PowerButtonTimestamp 129725280988099400
Event 89, Kernel-Power
ACPI thermal zone ACPI\ThermalZone\THM0 has been enumerated.
_PSV = 0K
_TC1 = 0
_TC2 = 0
_TSP = 0ms
_AC0 = 0K
_AC1 = 0K
_AC2 = 0K
_AC3 = 0K
_AC4 = 0K
_AC5 = 0K
_AC6 = 0K
_AC7 = 0K
_AC8 = 0K
_AC9 = 0K
_CRT = 371K
_HOT = 0K
_PSL - see event data.
---- Details
+
System
Provider
[ Name]
Microsoft-Windows-Kernel-Power
[ Guid]
{331C3B3A-2005-44C2-AC5E-77220C37D6B4}
EventID
89
Version
0
Level
4
Task
86
Opcode
0
Keywords
0x8000000000000020
TimeCreated
[ SystemTime]
2012-02-01T00:02:49.270411900Z
EventRecordID
8271
Correlation
Execution
[ ProcessID]
4
[ ThreadID]
68
Channel
System
Computer
LR8K6TLC.cntr.thrivent.corp
Security
[ UserID]
S-1-5-18
EventData
ThermalZoneDeviceInstanceLength
21
ThermalZoneDeviceInstance
ACPI\ThermalZone\THM0
AffinityCount
1
_PSV
0
_TC1
0
_TC2
0
_TSP
0
_AC0
0
_AC1
0
_AC2
0
_AC3
0
_AC4
0
_AC5
0
_AC6
0
_AC7
0
_AC8
0
_AC9
0
_CRT
371
_HOT
0
_PSL
0000000000000000
Thank you.We have tested and checked both the Bios and firmware of the SSD Drive's
Bios was up to date and no issue
Firmware was also up to date as well.
Users are still experiencing random Reboots. I tried to capture the issue with Procmon but since the PC shutdown (Goes to a black screen no power at all even when turning the "Automatically
restart" off under Startup and Recovery) No dmp files as of yet. Unable to configure Procdump due to not knowing where the issue is and what is causing it to happen.
Going to replace one of the PC's with a New one with different hardware to see if this resolve the issue. If anyone has any idea's to be able to capture what maybe happening that would
be great.
Thank you. -
My imac shuts down unexpectedly and now a fan is running??
Hello,
I have been working on my iMac all morning and it shut down twice within a half hour and I had to press the start button on the back to get it going again. Now their is a loud fan running and I have no idea what is going on. Help much appreciated. Thanks in advance!Hi ebeugs,
Thanks for visiting Apple Support Communities.
If your iMac shut down unexpectedly, and the fan is running unusually fast or loud, you may need to reset the System Management Controller.
I recommend following this troubleshooting method:
Before Resetting the SMC
Try each of the following steps in this order before you reset the SMC. Test the issue after completing each troubleshooting step to determine if the issue still occurs.
Press Command + Option + Escape to force quit any application that is not responding.
Put your Mac to sleep by choosing the Apple () menu from the upper-left menu bar and then choosing Sleep. Wake the computer after it has gone to sleep.
Restart your Mac by choosing the Apple () menu from the upper-left menu bar and then choosing Restart.
Shut down your Mac by choosing the Apple () menu from the upper-left menu bar and then choosing Shut Down.
If the iMac unexpectedly shuts down again, or the fan continues running unusually fast or loud, follow these steps:
Resetting the SMC for Mac Pro, Intel-based iMac, Intel-based Mac mini, or Intel-based Xserve
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
You can find these steps and more information about resetting the SMC here:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
Best Regards,
Jeremy -
My iphone 4 shuts down now and then battery is charged
since one week, my Iphone 4 shuts down now and then (randomly). then I have to push the top button to restart (apple sign) and after 1-2 minutes, its running again with unlocked sim. Can anyone tell me how to fix this. (my iphone 4 is 4 years old and i'm attached to it..) kind regards
Hi Asem,
From your post I see that your iPhone 4 is unexpectedly shutting down while you're using it. To help resolve this issue please follow the directions outlined below.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it
You might see this unexpected behavior on your iPhone, iPad, or iPod touch if you have an older version of iOS. These steps can help.
Make sure that your device is up to date and your apps are up to date. If you still see this issue after updating, contact Apple Support.
Learn what to do if your device won't start up past Apple logo or doesn't respond.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it - Apple Support
Have a good one,
Alex H. -
Since I installed Mountain Lion, my iMac has shut down after 15-20 minutes. I have adjusted screen saver, shut down time, and sleep after. Nothing seems to help, any ideas?
As old as your iMac is, have you cleaned out the dust? Dust buildup can lead to over heating issues. Remove any and all things plugged into it including the power cord, Remove the RAM access grille. Vacuum all openings starting with the RAM access area (air intake). Vacuum all ports and plugs, DVD slot and the opening across the top of the rear of the body. Blow compressed air through all your openings and vacuum again to remove any dust you loosend. Reinstall the RAM grille. Plug in the keyboard and mouse if not blue tooth. Insert power cord...
You are now in a perfect position to do a
SMC RESET
http://support.apple.com/kb/HT3964
Shut down the computer.
Unplug the computer's power cord and ALL peripherals.
Wait 15 seconds.
Attach the computers power cable.
Wait another 5 seconds and press the power button to turn on the computer.
It is the 5 second timing that initiates the reset.
Here is a link to a Widget to monitor your temps and other operations:
http://islayer.com/apps/istatpro/ -
Hello,
I recently tried downloading the IOS8 to my iPod 5th generation and when it was almost done the computer said there was an error. Right after that, the iPod shut down completely and now it's on recovery mode. I plugged it in and it said that I had to restore it and update it so I could use it again but it doesn't let me. What can I do? I even did a backup before the update.
I really need help.What happens when you connect to computer and restore via iTunes?
Without knowing that:
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
What's happening when i turn on my laptop it's blinking, I need to shut down or restart again. Please help!
Hello Melophage,
Thanks. Done..:)
BTW, I got another issue, hope can help me, I'm updating my OS X maverick to new one 10.9.2, while updating I need to restart my laptop to update, however i got this error message, "Install Failed! OS X could not be installed on your computer. The installer encounter an error that caused the installation fail. Contact the software manufacturer for assistance. Click Restart to restart your computerand try installing again." I did that so many times, unfortunately, nothing happens. This is the 1st time Ive ever encounter that issue while updating my Mac. Now, i cannot even go to my main menu, coz everytime I turn on my laptop it's shows the updating process and go back to failed installation. Thanks. -
why does my iPhone 5s shut down unpredictably and needs to be reset every time to start back up?
Hi Cyprus11,
Thanks for visiting Apple Support Communities.
If your iPhone is shutting down unexpectedly, I recommend going through these troubleshooting steps:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Best,
Jeremy -
IPhoto shuts down over-and-over when importing from iPhone
When trying to import photos from iPhone to iPhoto, iPhoto begins the import but then immediately shuts down. over and over again. I've looked online for a solution but have not found anything that I have tried. I am not very comfortable with technology so hesitate to try anything without some direction.
iPhoto 7.1.5
Max OS X version 10.7.4
Error Report:
Process: iPhoto [10596]
Path: /Applications/iPhoto.app/Contents/MacOS/iPhoto
Identifier: com.apple.iPhoto
Version: 7.1.5 (7.1.5)
Build Info: iPhotoProject-3780000~2
Code Type: X86 (Native)
Parent Process: launchd [132]
Date/Time: 2012-07-31 11:01:54.073 -0700
OS Version: Mac OS X 10.7.4 (11E53)
Report Version: 9
Interval Since Last Report: 677058 sec
Crashes Since Last Report: 11
Per-App Interval Since Last Report: 584991 sec
Per-App Crashes Since Last Report: 10
Anonymous UUID: 92C8D8A3-29DF-40C3-8BCD-DD0608B6198D
Crashed Thread: 7
Exception Type: EXC_BAD_ACCESS (SIGBUS)
Exception Codes: KERN_PROTECTION_FAILURE at 0x0000000000000020
VM Regions Near 0x20:
--> __PAGEZERO 0000000000000000-0000000000001000 [ 4K] ---/--- SM=NUL /Applications/iPhoto.app/Contents/MacOS/iPhoto
__TEXT 0000000000001000-00000000006b2000 [ 6852K] r-x/rwx SM=COW /Applications/iPhoto.app/Contents/MacOS/iPhoto
Application Specific Information:
objc[10596]: garbage collection is OFF
Thread 0:: Dispatch queue: com.apple.main-thread
0 libsystem_kernel.dylib 0x98114c22 mach_msg_trap + 10
1 libsystem_kernel.dylib 0x981141f6 mach_msg + 70
2 com.apple.CoreFoundation 0x973869da __CFRunLoopServiceMachPort + 170
3 com.apple.CoreFoundation 0x9738fb04 __CFRunLoopRun + 1428
4 com.apple.CoreFoundation 0x9738f1dc CFRunLoopRunSpecific + 332
5 com.apple.CoreFoundation 0x9738f088 CFRunLoopRunInMode + 120
6 com.apple.HIToolbox 0x98810723 RunCurrentEventLoopInMode + 318
7 com.apple.HIToolbox 0x98817a8b ReceiveNextEventCommon + 381
8 com.apple.HIToolbox 0x988178fa BlockUntilNextEventMatchingListInMode + 88
9 com.apple.AppKit 0x9a4780d8 _DPSNextEvent + 678
10 com.apple.AppKit 0x9a477942 -[NSApplication nextEventMatchingMask:untilDate:inMode:dequeue:] + 113
11 com.apple.AppKit 0x9a473cb1 -[NSApplication run] + 911
12 com.apple.AppKit 0x9a704bd9 NSApplicationMain + 1054
13 com.apple.iPhoto 0x00002ce6 0x1000 + 7398
14 com.apple.iPhoto 0x00002c0d 0x1000 + 7181
Thread 1:: Dispatch queue: com.apple.libdispatch-manager
0 libsystem_kernel.dylib 0x98116b5e __select_nocancel + 10
1 libdispatch.dylib 0x90f80cc9 _dispatch_mgr_invoke + 642
2 libdispatch.dylib 0x90f7f85f _dispatch_mgr_thread + 53
Thread 2:: com.apple.CFSocket.private
0 libsystem_kernel.dylib 0x98116b42 __select + 10
1 com.apple.CoreFoundation 0x973dde15 __CFSocketManager + 1557
2 libsystem_c.dylib 0x97588ed9 _pthread_start + 335
3 libsystem_c.dylib 0x9758c6de thread_start + 34
Thread 3:
0 libsystem_kernel.dylib 0x9811683e __psynch_cvwait + 10
1 libsystem_c.dylib 0x9758ce78 _pthread_cond_wait + 914
2 libsystem_c.dylib 0x9758cf7b pthread_cond_timedwait_relative_np + 47
3 com.apple.CoreServices.CarbonCore 0x95e903a7 TSWaitOnConditionTimedRelative + 178
4 com.apple.CoreServices.CarbonCore 0x95e9011d TSWaitOnSemaphoreCommon + 490
5 com.apple.CoreServices.CarbonCore 0x95e8ff2e TSWaitOnSemaphoreRelative + 24
6 com.apple.QuickTimeComponents.component 0x91a64516 0x91478000 + 6210838
7 libsystem_c.dylib 0x97588ed9 _pthread_start + 335
8 libsystem_c.dylib 0x9758c6de thread_start + 34
Thread 4:
0 libsystem_kernel.dylib 0x9811702e __workq_kernreturn + 10
1 libsystem_c.dylib 0x9758accf _pthread_wqthread + 773
2 libsystem_c.dylib 0x9758c6fe start_wqthread + 30
Thread 5:
0 libsystem_kernel.dylib 0x9811702e __workq_kernreturn + 10
1 libsystem_c.dylib 0x9758accf _pthread_wqthread + 773
2 libsystem_c.dylib 0x9758c6fe start_wqthread + 30
Thread 6:
0 libsystem_kernel.dylib 0x9811702e __workq_kernreturn + 10
1 libsystem_c.dylib 0x9758accf _pthread_wqthread + 773
2 libsystem_c.dylib 0x9758c6fe start_wqthread + 30
Thread 7 Crashed:
0 com.apple.ImageIO.framework 0x9a3f5fdb _JPEGFile::writeToStream(__CFWriteStream*) + 151
1 com.apple.ImageIO.framework 0x9a3f7ed9 _JPEGWriter::writePropertiesAndData(__CFWriteStream*) + 99
2 com.apple.ImageIO.framework 0x9a3f7f4f _JPEGWriter::writeToPath(__CFString const*) + 109
3 com.apple.ImageIO.framework 0x9a3f9c5b CGImageCopyFileWithParameters + 2588
4 com.apple.iPhoto 0x001a0c02 0x1000 + 1702914
5 com.apple.iPhoto 0x00103555 0x1000 + 1058133
6 com.apple.iPhoto 0x0029cbc4 0x1000 + 2735044
7 libsystem_c.dylib 0x97588ed9 _pthread_start + 335
8 libsystem_c.dylib 0x9758c6de thread_start + 34
Thread 8:
Thread 9:
0 libsystem_kernel.dylib 0x9811683e __psynch_cvwait + 10
1 libsystem_c.dylib 0x9758ce78 _pthread_cond_wait + 914
2 libsystem_c.dylib 0x9758cf7b pthread_cond_timedwait_relative_np + 47
3 com.apple.CoreServices.CarbonCore 0x95e903a7 TSWaitOnConditionTimedRelative + 178
4 com.apple.CoreServices.CarbonCore 0x95e9011d TSWaitOnSemaphoreCommon + 490
5 com.apple.CoreServices.CarbonCore 0x95e8ff2e TSWaitOnSemaphoreRelative + 24
6 com.apple.CoreServices.CarbonCore 0x95ec2e53 AIOFileThread(void*) + 1019
7 libsystem_c.dylib 0x97588ed9 _pthread_start + 335
8 libsystem_c.dylib 0x9758c6de thread_start + 34
Thread 7 crashed with X86 Thread State (32-bit):
eax: 0x00000000 ebx: 0x21ce05f0 ecx: 0x12ddf250 edx: 0x0052c600
edi: 0x12df52e0 esi: 0x00000001 ebp: 0xb041f8b8 esp: 0xb041f890
ss: 0x00000023 efl: 0x00010293 eip: 0x9a3f5fdb cs: 0x0000001b
ds: 0x00000023 es: 0x00000023 fs: 0x00000023 gs: 0x0000000f
cr2: 0x00000020
Logical CPU: 0As a Test:
Hold down the option (or alt) key and launch iPhoto. From the resulting menu select 'Create Library'
Import a few pics into this new, blank library. Is the Problem repeated there? -
It shuts down unexpectedly and then it says something like "Overheat or something
Hi! My HP laptop is Pavilion dm4.
Problem: It shuts down unexpectedly and also when i touch the left side of my laptop, its so hot.Compressed air is completely safe to use on the laptop.I use it every couple of months to clean both of mine and even inside the case of my desktop. Just be sure the laptop is shut down and keep the can in upright position. If not it can disperse some of the liquid propellant in the bottom of can.
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
My iPad randomly shuts down apps and Safari...any fixes for this?
Basic troubleshooting steps might help. If you are using the iPad 1, low memory issues may be causing the app and Safari to crash.
Quit all apps completely and restart the iPad. Go to the home screen first by tapping the home button. Double tap the home button and the task bar will appear with all of your recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar. Restart the iPad.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
Definitely do this - Go to Settings>Safari>Clear History, Cookies and Data. Restart the iPad. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button. -
My macbook pro shuts down OSX and all my programs when the lid is closed
Hi,
I am having a problem. My macbook pro shuts down OSX and all my programs when the lid is closed. I close the lid, and then I hear the shutdown music and then when I open it again it automatically restarts OSX and all my windows and programs are closed, any info gone.
This doesn't happen all the time. Just once a day or maybe twice a day. It seems like it happens basically when I have my computer just the way I want it, to keep an eye on things for the day.
I just recently switched to a mac and while somewhat savvy, I am not a programmer or techie, but it seems to me that when I shut the lid, it should do the same thing every time.
I have a intel core 2 duo 17 inch macbook pro with 2.33 processr and 2 gig ram, if that helps.
I am in alaska and there is no genius bar here and I am hoping to figure this out before I begin bugging our local independant mac store about this.
Thanks in advance,
Lylah
17 inch Macbook Pro Mac OS X (10.4.9) intel core 2 duo 2.33g. 2 gig ramAhhh, enlightenment!
That would make sense. What I usually do, after closing the lid, is to wait for the apple to turn off and then set it down on it's side leaning it against the side table. I will try to wait for it to indicate that it is fully asleep before I move it next time. Personally, I prefer my computer to NOT fall asleep at all, but I am told it is not an option. Apparently this function is hardware related accoring to my local mac shop. They tracked it down for me because I hated this feature when I first bought my computer and was trying some way around it.
The shutdown music I was refering to was that music the mac makes when shutting down, which doesnt usually occur when it goes to sleep, unless it is malfunctioning like this.
What does resetting the pmu do? (what is a pmu as well?)
Thank you very much.
Lylah
Maybe you are looking for
-
Is adobe photoshop 7 compatible with microsoft xp pack 3
Is adobe photoshop 7 compatible with microsoft xp service pack 3?
-
Mac OS X Vs. Windows Vista
Hello everyone. I just recently became a Mac user. So far I love it so much more then using a PC. I upgraded to a new Macbook from a Dell laptop. I just got so annoyed with all the problems and bugs I kept having with windows, and keeping up with the
-
Change Multiple Predecessors - How to ?
Help! Is it possible to change multiple (activity) Predecessors at once? for example if I only want to change 1 predecessor, i would do it manully. (by clicking on it and making the new selection) However, if i have 100 projects open and i need to ch
-
Hi can i give Aleternate color to records in crystal reports? Thank you
-
Hi all, I have alv table for create PR. i have entered values in first row but incomplete and tries to add another row but it show the message like enter the value in the field(field name). after the values are entered completely in the first row, it