Stereo system and viera cast connection

i have a 50" viera cast plasma tv a panasonic blue ray
I want to listen to to pandora an netflix through the sound system. I can listenb to tv and blu ray through it but when I get netflix or pandora it does not play through the audio system.
the cat 5 cable is hooked through the TV Tv is hooked to blue ray through hdmi and tv to cable box via hdmi
i have fiberoptic cable from the blue ray to stereo and stereo to TV
do i need a fiber audio cable from TV to stereo as well?

A fiberoptic cable should be connected from the TV to a input of the stereo. I am just not really sure aobut your comment:
"i have fiberoptic cable from the blue ray to stereo and stereo to TV"
I undesrtand you have a fiber cable from BD to your stereo. But the other part are you saying you are using stereo RCA connections to the TV? because if you already have a fiber optic cable connecting your TV to stereo it should be working

Similar Messages

Time capsule and Viera Cast

Hi - I've just purchased a Panasonic TC-P50G10 plasma TV that is able to be directly hooked up to the internet. I have a cable modem connected to Time Capsule and the TV is connected with via a LAN port from the Time Capsule to an ethernet port on the TV. When I check the network connection to the TV it says it successful and can obtain an IP address. However when I try to connect to the internet via the Viera Cast function of the TV it says "connection to server failed 006". I think that there is something about Time Capsule that is not allowing the TV to talk to the server. Any suggestions on how to proceed? I've tried rebooting the router and modem with no success.

Welcome to the discussions!
Suggest that you perform an additional troubleshooting step as follows:
Temporarily disconnect the ethernet cable at the TV and plug it in to your laptop. Make sure that wireless is turned off on your laptop so that it will connect using ethernet.
Try to pull up several websites on your laptop. If you can, there is nothing in the TC blocking access to a website.
Reconnect the ethernet cable to the TV and power the TV down as well as the rest of your network. Then start the modem first for a few minutes alone, then the TC for a few minutes, then your TV and computers.
Any help? If not, you will need to check with Panasonic support to troubleshoot further as you can verify to them that you have a reliable internet connection at your end.

Apple tv viera cast 2008. I want to add apple tv via hdmi connection, viera cast which has Amazon prime is already connected thru ethane port on tv. my network is wifi from APE base and APX. Will this set up work?

I want to add apple tv via hdmi connection , and I already have ethernet input of tv for my viera cast connection, which gets Amazon prime. Wireless connection is APE base and APX, Want to add
apple tv to get Netflix so I can cancel my xfinity premium channels. Will this set up work. p.s as you can tell I am a Mac novice.

Providing you have a free HDMI port on the TV and the location you would put the Apple TV will allow it to connect to your network, you should be good to go.

Extraction failing after source system and client copy

Hi all,
We refreshed our source QA system with a copy of production. And basically tried to "restore" the connection from our BW QA system. Some of the datasources can be extracted from BW, others fail with an error of "No transfer structure is available for InfoSource 0COSTCENTER_ATTR in the source system".
Trying to do the same thing with RSA3 in the source system, works fine.
The strange thing is it works for some objects but not others.
here's what we did:
1. System copy from R3 Prod to R3 QA
2. Client copy with R3 QA client 300 -> 200
3. Restore connectivity in BW QA to the R3 QA system (Using RSA1 -> Source System -> Restore)
4. Now some objects can be extracted in BW, others fail as I mentioned above.
I have regenerated the transfer structures in BW and R3.
All of these objects that don't work seem to work in RSA3 on the R3 system but not in RSA1 on BW.
All the SAP documentation is geared to copying the R3 source system and then restoring connectivity between BW and R3. I don't think any of it involves copying the client in the R3 source system - which might be causing our problems.
We are using an SAP delivered PDF and note 886102 mainly for direction.
SAP PDF is "How to... System Copy in SAP Business Intelligence System Landscapes".
Does anyone have any ideas?
Thanks,
Kevin

Hi,
can you isolate somehow the kind of DataSource which works and those who don't?
Master data / transactional or client dependent and not, delta or full....
To which R/3 client is your BW connected? when you succeed loading the data, is it coming from the right client?
RSA3: do you run it specifying your BW client in the target sys field? does it make a difference if yes or if not?
Are your RFC connections and partner profiles all right?
Check some IDOCs sent by BW received in R/3 and vice-versa (RSSEND, RSINFO, RSRQST..). Load a hierarchy (via IDOC)... verify that your IDOC have the correct partner settings....
let us know
Olivier.
Message was edited by:
Olivier Cora

I connected my iPod Touch to a stereo system phono input using a cable with stereo jacks (red and white) on one end and that plugs into the iPod's headphone jack. The problem is that the sound is extremely muffled and bass-heavy, with little treble.

I connected my iPod Touch to a stereo system phono input using a cable with stereo jacks (red and white) on one end and that plugs into the iPod's headphone jack. The problem is that the sound is extremely muffled and bass-heavy, with little treble. I have to turn the bass control on the stereo receiver to pratically zero in order for the sound coming through the stereo to be acceptable. Is there a setting on either the iPod or the stereo that I need to change in order to fix this?

The phono input is for a phonograph. The iPod does headphne output is not that same as a phongraph output. Does th stero have an AUX input? That should be compatible.

What is the best way to connect an ipod to a home stereo system

i forgot my ipad password - i entered the wrong password a number of times and am now locked out - what do i do to start again?

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
The best way depends upon your stereo system. If you system has an AUX input you can get a cable that goes from the headphone jack to the AUX in

Connecting iMac 24" to Stereo System

I've just ordered a 24" iMac 3.06 Ghz machine. I would like to use the optical interface to connect to a stereo system (hopefully with 5:1 surround sound support). Can I do this? What currently sold brands and models of receivers allow this? Will I have to buy the optical cable separately?
I have also purchased the 24" Cinema Display for dual head computing. I know it has its own sound options. But my Infinity speakers are likely to be better (plus I have a Velodyne sub)
I do have a rather old Sony STR-G3. I do not know if it supports the right connection type.
Thank you.

Hornet Developer,
Welcome to the forum and congratulations on your new iMac. You should be able to successfully connect your iMac to a hi-fi system and get 5.1 sound on at least iTunes material. This is assuming of course the content in iTunes was recorded in 5.1. In fact if you have an Airport Express you can even do it wirelessly, using Apples Air Tunes feature.
This will work with any receiver that supports optical input, there are even some powered speakers available so this would work with them as well.
Yes you do need to purchase a separate cable however they are relatively inexpensive. An example would be something like this:
http://cgi.ebay.com/Optical-TOSLink-to-Mini-AUDIO-Cable-6ft-for-Apple-MacW0QQitemZ230378402121QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item35a39f7149&_ trksid=p4999.c0.m14#ht_1400wt1170
Assuming your Sony STR-G3 supports optical in and it's functioning OK you should only need a cable to connect your iMac and you're good to go. If you want to do this wirelessly you would need to get a cable and the Airport Express which would connect to your wireless network. I do this myself with my Imac, my wireless router is the Airport Extreme and I have a Airport Express connected to a B&K Reference 50 Pre-Pro which is connected (via my separate amp) to my B&W Nautilus speakers.
Regards,
Roger

Connecting my home stereo system to my macbook pro

I want to connect my stereo system to my MacBook Pro in order to put some of my Pops old vinyl onto CD to play when out and about. Please can someone advise best option. Usual stereo phono out from the amp.
Thanks
Nii Naku

Well, there are many options you can use. If you have a home stereo, with only two channels, you can go to radio shack and get a splitter cable, one with the red and black/white RCA connectors on one end, and then the 1/8th inch headphone connector on the other end, and then plug the RCA's into you stereo in the line out ports, and then the headphone into the line in on the MBP, and you are all set. You can even go into system prefs and sound under line in or recording, play the record and see what the MBP is registering for line in volume and adjust it to get the best sound.

IMac-stereo system wireless connection?

Suggestions wanted, please, for wireless connection of IMac with Airport Extreme card and/or Bluetooth to older stereo system in other room to play ITunes/Internet-accessed radio stations.

Do you know whether it can be used simultaneously with other tasks, such as printing wirelessly via Airport and browsing? I could never print without switching off Internet access in order to connect to my printer.
Yes, the AX can be configured in several ways, including a remote base station in a Wireless Distribution System (WDS). In a WDS, the AX would both extend your current AEBSn's wireless network and provide a means to stream iTunes and/or share a USB printer concurrently.
Where is a good guide to all these connectivity issues?
There are several good ones at the following link: Apple Manuals

Having a problem with wireless connection. On my Windows XP 32 bit system and a 6510 printer, initi

On my Dell Latitude D620, Windows XP 32 bit system and my 6510 printer wireless connection (Linksys EA4500) , everything works fine after the computer is booted. After a period of time (usually overnight), I lose connection to the printer (the scanner icon with a red x is shown on my Windows task bar and I can't print. Ran Windows Fix and the HP fix programs. The only thing that solves it is to reboot the computer. A second symptom is that my IE8 stops connecting to the internet at the same time (gives a 'waiting for' response that never changes). Firefox still connects OK when this is happening. So I suspect the problem isn't with the printer, but with my Windows set up. It is a fresh XP SP3 install (hard drive crashed, but it happened before also). I reset IE, checked my proxy, no malware, happens with or without firewalls and security programs.
Hoping that someone else has run into this problem. Been all over Google, and the IE doesn't work / Firefox works is fairly common, but none of the fixes helps.

If you want you can reload Firefox 4.0 or the last "old" version is 3.6.16 and is available here:
http://www.mozilla.com/en-US/firefox/all-older.html
Just reinstall your choice of FF. The bookmarks are in a different directory and are NOT overwritten. Some of the Add-ons that worked in 3.6 DO NOT work with 4.0, pay attention and head any warnings when you start 4.0.
I had to disable extensions: Flashblock and WOT
Firefox SafeMode? - A troubleshooting mode.
1.You can open the Firefox 4.0 SafeMode by holding the Shft key when you use the Firefox desktop or Start menu shortcut.
To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut to open it again.
For more help, see this: http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes
Hope this helps you out.
Feedback is appreciated especially if this helps you out.

How Many systems like ECC and BI can connect to EP server

Dear experts
I want to know ,how many systems can connect to one EP server,like ECC dev,qty and prd ,and BI dev,qty and prd with JCO and SSO connection...can you please clarify
Thanks in advance
Regards
krishna

Hi Krishna,
The best practice is to have separate systems for Development, Quality Assurance and Production.
Suppose you have One EP system, One ECC system, One BW System and One SRM system.
Then your landscape should be designed as stated below.
Development Environment:
Here you work on new developments/bug fixes and enhancements.
One EP System, One ECC system, One BW System and One SRM system.
And all these systems must be connected to EP system.
All of the above systems must reside in same domain.
QA Environment:
Here testing is done by testers/business.
Once you complete development and unit testing you have to transport those objects to QA system.
In this environment you have maintain all the systems similar to Dev Environment.
Production Environment:
This environment is for end users.
It should contain all the above said systems.
Here strictly no development/testing is not allowed.
Objects are transported from DEV> QA>PROD.
Regards,
Nagireddy.

How can I connect laptop to stereo system?

I have a Pavillion dm3 1130us and I want to go out of it into my stereo system to play the pc audio on the stereo. It''s got headphone output which traditionally won't work to line in of the stereo, but are there settings on the pc that will allow it to work with line in?
And, what are my options for doing this wirelessly? Is there any way I can use my wireless router for this?
Thank you!

I think you would want an Airport Express
The Express is designed to work with iTunes, but with the following (free) program you can use the Express to play any PC audio without iTunes: Airfoil Speakers for Windows
All this will work with any router, wired or wireless. Enjoy!

Please tell me which Ipod dock adapter is compatible with the Ipod Classic 80GB? They no longer make this particular Ipod and I need the right dock adapter for my Panasonic SC-HC25 stereo system I recently purchased.

Please tell me which Ipod dock adapter is compatible with the Ipod Classic 80GB? They no longer make this particular Ipod and I need the right dock adapter for my Panasonic SC-HC25 stereo system with universal dock for Ipod/Iphone I recently purchased.
You can also send my answer to [email protected]
Thanks in advance for all who will help.
slovebk

refer to this Apple support Article, on Universal Dock which retail at $59 at Apple store.
http://support.apple.com/kb/HT1380
Look through the compatible list chart and see which 80GB model are you using, either ID 9 or 10. you can order through Apple Online Store.
Have a nice day!

I have a 1TB WD external hard disk, which suddenly cannot be detected in my system. When i connect the hardisk to the macbook, the disk appears and immediately disconnects with the message "Disk not properly ejected". Any advice ?

I have a 1TB WD external hard disk, which suddenly cannot be detected in my system. When i connect the hardisk to the macbook, the disk appears and immediately disconnects with the message "Disk not properly ejected". Any advice ?

verify on another Mac if the same
WD is having issues with mavericks as you can see on the WD forum, did you install any WD software (never do that) when you connected the drive for the first time?
possible issue is a dead SATA bridge card or the new WD firmware w/ Mavericks.
SATA card issue
Your dead external hard drive is likely fine! Great hope for your 'faulty' external HD
http://community.wd.com/t5/External-Drives-for-Mac/bd-p/passport_mac
verify on another Mac if all possible

I downloaded the iOS7 system and lost connectivity to my in-ceiling speakers and Air Play. How do I get it back?

I downloaded the iOS7 system and lost connectivity to my in-ceiling speakers and Air Play. How do I get it back?

Use the iOS7 Control Center to select AirPlay, and then, choose the appropriate AirPlay speaker to stream to.

Stereo system and viera cast connection

Similar Messages

Maybe you are looking for