Sticky Resource Not Available when setting up sticky http-cookie
When I try to configure the sticky:
(config)# sticky http-cookie ACE-COOKIE COOKIE-STICKY
I get the error:
sticky resource not available
An L7 policy has not yet been set up⦠could that be the reason for this error? Or, is it because I have not setup a class resource for the sticky cookie?
Syed,
I thought it resolved it, but it really didn't.
Added the resource-class in the Admin context:
resource-class any-available
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 35.00 maximum equal-to-min
no difference.
Similar Messages
-
Sticky resource not available - ACE Module
hi,
I am getting the below error on defining stickiness. Please assist.
switch/Admin(config)# sticky ip-netmask 255.255.255.255 address both ACE-CKH-STICKY
Error: sticky resource not available
Thanks.Note The syslog message statistics do not include the syslogs generated from the dataplane when you enable the logging of connection setup and teardown syslog messages through the logging fastpath command.
â¢regexp-Limits the amount of regular expression memory.
â¢sticky-Limits the number of entries in the sticky table. You must configure a minimum value for sticky to allocate resources for sticky entries, because the sticky software receives no resources under the unlimited setting.
â¢xlates-Limits the number of network and port address translations entries.
â¢minimum number-Specifies the lowest acceptable value. Enter an integer from 0.00 to 100.00 percent (two-decimal places of granularity). The number argument specifies a percentage value for all contexts that are members of the class. When used with the rate keyword, the number argument specifies a value per second.
â¢maximum {equal-to-min | unlimited}-Specifies the maximum resource value: either the same as the minimum value or no limit.
Note The limit that you set for individual resources when you use the limit-resource command overrides the limit that you set for all resources when you use the limit-resource all command.
If you lower the limits for one context (context A) in order to increase the limits of another context (context B), you may experience a delay in the configuration change because the ACE will not lower the limits of context A until the resources are no longer being used by the context.
For example, to allocate 20 percent of all resources (minimum and maximum) to all member contexts of the resource class, enter:
(config-resource)# limit-resource all minimum 20% maximum equal-to-min
System Resource Maximum Values
Resource Maximum Value
Application Acceleration Connections
10000 connections
ACL Memory
34123184 bytes
Buffer Memory (Syslog)
1048576 bytes
Concurrent Connections
1,000,000 connections (Layer 4),
100,000 connections (SSL)
HTTP Compression
100 megabits per second (Mbps). You can upgrade the ACE maximum HTTP compression rate to 1 Gbps by purchasing a separate license from Cisco Systems. For more information, see the Cisco 4700 Series Application Control Engine Appliance Administration Guide.
Management Connections
5000 connections
Proxy Connections (Layer 7)
256,000 connections
Rate
Bandwidth
1 gigabits per second (Gbps). You can upgrade the ACE maximum bandwidth to 2 Gbps by purchasing a separate license from Cisco Systems. For more information, see the Cisco 4700 Series Application Control Engine Appliance Administration Guide.
Connections (any kind)
120,000 connections per second (Layer 4), 40, 000 connections per second (Layer 7)
MAC miss
2000 packets per second
Management traffic
125,000,000 bits per second
SSL connections
1000 transactions per second (TPS). You can upgrade the SSL bandwidth to a maximum of 7500 TPS with a separate license. For more information, see the Cisco 4700 Series Application Control Engine Appliance Administration Guide.
syslog
For traffic going to the ACE (control plane), 3000 messages per second
For traffic going through the ACE (data plane), 120,000 messages per second
Regular Expression Memory
1,048,576 bytes
Sticky Entries
800,000 table entries
Xlates (network and port address translation entries)
64,000 Xlates (network entries),
1,000,000 Xlates (port address translation entries)
Kind Regards,
Sachin Garg
Senior Specialist Security
HCL Comnet Ltd.
http://www.hclcomnet.co.in
A-10, Sector 3, Noida- 201301
INDIA
Mob: +91-9911757733
Email: [email protected] -
Sticky resource not available ?
I get the following error message then i try to configure sticky on an ACE:
Error: sticky resource not available
What is the problem ?
I have release "c6ace-t1k9-mz.A2_1_2.bin" and sticky should be supported.
ace-10/RGW_Front_servers(config)# sticky ip-netmask 255.255.255.255 address source RGW-FRONT
Error: sticky resource not available
Regards,
Ola HaglundHi Ola,
By default sticky resources are not available. You need to go to the Admin context and define a new resource class with some stickiness. See Server LoadBalancing Guide Chapter 5 p8. For example:
resource-class RC1
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 10.00 maximum equal-to-min
Obviously the amount of sticky resource to allocate will depend on your application.
And then you need to make the context that needs stickiness a member of that resource class.
For example:
context Test
allocate-interface vlan 292-293
member RC1
HTH
Cathy -
Error message "iTunes Helper Resources not available" and saving to wrong Drive
I am trying to upgrade iTunes to 10.7 on my PC but I keep getting the error message "iTunes Helper Resources not available". Diagnostics take me a support page which talks about not being able to see the device in iTunes - but I can see the device without problems.
I thought I would try reinstalling iTunes from the webpage and it downloaded to my PC fine but when I went to setup, it showed me it is saving to a DVD drive - not my Hard drive. It also won't let me change the location for the file. I have no idea how that's happened as I obviously don't use the DVD drive as a USB (although the PC see's it as one) and I've never chosen it as the location for iTunes in the 7-8 years that I've been using it.
I then thought I'd try uninstalling it and reinstalling it (to the correct drive) but again, it comes up that the DVD drive is invalid and won't uninstall iTunes.
So I'm stuck and haven't been able to find anything helpful on the support pages or in iTunes Help.
Please someone help ...
Thanks.Try the following user tip. (Probably, the section on clearing the installation database might be best given that you've currently got a drive on the problematic letter at the moment.)
"Invalid drive X:\" install errors -
"Content Editing" is not available when I go to the Tools sidebar--how can I access these features? I'm using Acrobat X 10.1.7. Thanks.
The headings under Tools are: "Pages", "Content", "Forms", "Recognize Text", "Protection", and "Sign & Certify". There's also a little icon in the upper right that lets me access some other headings under the Tools menu; those are: "Document Processing", "JavaScript", "Accessibility", and "Analyze".
I did think about the idea that maybe the Content Editing was a new feature of Acrobat XI, but I found some resources online (http://www.wikihow.com/Edit-Text-in-Adobe-Acrobat) that seem to indicate this was a feature on much earlier version (the link references Acrobat 8 at the bottom).
Really confused...
Thanks for your thoughts -
Touch id option not available when purchasing an app
Touch id option is not available when im purchasing an app. I already enable touch id when app purchase why is that happen
Hey renzmartincruz,
It might be due to the following:
Note: Touch ID cannot be used for purchases if Require Password in Settings > General > Restrictions is set to Immediately.
For full instructions on setting it up, check out the following document:
iPhone 5s: Using Touch ID
http://support.apple.com/kb/HT5883
Have a good one,
Delgadoh -
Requested resource not available - can not find servlet
I have an application in tomcat that uses jsp and servlets. The JSP works fine, but I keep getting a "requested resource not available" erroe when i try to access a servlet. My jsp is in a directory called ProjectManager, and my servlet classes are in WEB-INF/classes inside ProjectManager and are in a package called pmt.
I can access my jsp using localhost:8080/ProjectManager/index.jsp, but I cannot seem to access the servlets, regardless of the URL I try. I've tried adding a servlet-name and a servlet-mapping in the web.xml file but I'm still stuck.
Does anybody have any ideas?
Thanks in advance.What jar files should be in the library? I have the following:
commons-lang-2.4(2).jar
mysqlconnector-java-5.1.6.bin.jar
webserviceutils.jar
Here is my web.xml as I too am getting "the request resource....cannot be found:
<?xml version="1.0" encoding="UTF-8"?>
<web-app id="WebApp_ID" version="2.4" xmlns="http://java.sun.com/xml/ns/j2ee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/j2ee http://java.sun.com/xml/ns/j2ee/web-app_2_4.xsd">
<display-name>
classBlog</display-name>
<servlet>
<description>
</description>
<display-name>
DriverServlet</display-name>
<servlet-name>DriverServlet</servlet-name>
<servlet-class>
edu.ec.web.classBlog.DriverServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
AddEntityServlet</display-name>
<servlet-name>AddEntityServlet</servlet-name>
<servlet-class>
com.ec.blog.web.AddEntityServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
DeleteEntityServlet</display-name>
<servlet-name>DeleteEntityServlet</servlet-name>
<servlet-class>
com.ec.blog.web.DeleteEntityServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
EditEntityServlet</display-name>
<servlet-name>EditEntityServlet</servlet-name>
<servlet-class>
com.ec.blog.web.EditEntityServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
ViewBlogServlet</display-name>
<servlet-name>ViewBlogServlet</servlet-name>
<servlet-class>
com.ec.blog.web.ViewBlogServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
ViewEntityServlet</display-name>
<servlet-name>ViewEntityServlet</servlet-name>
<servlet-class>
com.ec.blog.web.ViewEntityServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
AddEntryServlet</display-name>
<servlet-name>AddEntryServlet</servlet-name>
<servlet-class>
com.ec.blog.web.AddEntryServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
DeleteEntryServlet</display-name>
<servlet-name>DeleteEntryServlet</servlet-name>
<servlet-class>
com.ec.blog.web.DeleteEntryServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
EditEntryServlet</display-name>
<servlet-name>EditEntryServlet</servlet-name>
<servlet-class>
com.ec.blog.web.EditEntryServlet</servlet-class>
</servlet>
<servlet>
<description>
</description>
<display-name>
ViewEntryServlet</display-name>
<servlet-name>ViewEntryServlet</servlet-name>
<servlet-class>
com.ec.blog.web.ViewEntryServlet</servlet-class>
</servlet>
<servlet-mapping>
<servlet-name>DriverServlet</servlet-name>
<url-pattern>/DriverServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>AddEntityServlet</servlet-name>
<url-pattern>/AddEntityServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>DeleteEntityServlet</servlet-name>
<url-pattern>/DeleteEntityServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>EditEntityServlet</servlet-name>
<url-pattern>/EditEntityServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>ViewBlogServlet</servlet-name>
<url-pattern>/ViewBlogServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>ViewEntityServlet</servlet-name>
<url-pattern>/ViewEntityServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>AddEntryServlet</servlet-name>
<url-pattern>/AddEntryServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>DeleteEntryServlet</servlet-name>
<url-pattern>/DeleteEntryServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>EditEntryServlet</servlet-name>
<url-pattern>/EditEntryServlet</url-pattern>
</servlet-mapping>
<servlet-mapping>
<servlet-name>ViewEntryServlet</servlet-name>
<url-pattern>/ViewEntryServlet</url-pattern>
</servlet-mapping>
<welcome-file-list>
<welcome-file>index.html</welcome-file>
<welcome-file>index.htm</welcome-file>
<welcome-file>index.jsp</welcome-file>
<welcome-file>default.html</welcome-file>
<welcome-file>default.htm</welcome-file>
<welcome-file>default.jsp</welcome-file>
</welcome-file-list>
</web-app> -
Personalise value icon not available when query executed from portal
Hi
The personalise value icon is not available when the query is executed from the portal.
Is this the norm or is there anything i must change?
Regards
ShaliniSince you have not given us much information to go on, I will start with the basics...
Have you activated the Personalization DSOs (0PERS_WTE, 0PERS_BOD & 0PERS_VAR)?
If not, you will need to do so in tcode SPRO (SAP Reference IMG --> SAP NetWeaver --> Business Intelligence --> Settings for Reporting and Analysis --> General Settings for Reporting and Analysis --> Activate Personalization in BEx)
Are you running a BW 3.5 query or a BI 7.0 query?
If BI 7.0, the way to set personalization values has changed. You have to open the personalization section of the variables refresh screen by clicking on "Show Personalization Values" at the top of the screen, then move the desired variables down to that section.
Hope some of this helps...
Bob -
Why is closed captioning not available when renting movies?
I've rented a few movies on iTunes and noticed that none that I've rented so far are closed captioned nor offer subtitles in English as an alternative. Yes, the setting is set to show these by default, and I go in to double check anyway -- it's on.
Why is this? If I were to rent this on DVD, these same movies would be captioned. Is this not available when digitally downloaded?Hi daisyintampa,
Well, normally movies from the iTunes Store don't include such feature. Despite that, sometimes you'll find a few movies with CC and/or Subtitles...
Definitely all this rules are imposed by the Studios and not by Apple! However, you may want to leave feedback for Apple, by using [this link|http://www.apple.com/feedback/itunesapp.html].
Hope this helps!
Francisco -
Why does photo information not available when you email a photo?
Why does photo information not available when you email a photo?
How are you mailing from iPhoto? If you have iPhoto set to mail using Mail.app, you can set what will be included, when you mail with Share > Mail:
-
Grid Control performance tab not available when on the target home of ASM
I noticed recently that the "Performance" tab/link is not available when you are using 10g Grid Control and you are on the home page of an ASM instance. Can this be explained?
Hi MarGur
I try to help you. The OEM Grid Control in some times not discover the Oracle 9i databases and you must to add manually.
First, check in your target machine that the user owner of agent software have rights of read and write in the ORACLE_HOME directories of Oracle 9i databases.
Go to Grid Control Console
Select Targets ---> Databases
Press Add --> Select the host ebisdb2.oneshield.com and press continue
The automatic discover process begin. When finished is very normal that nor discover the Oracle 9i databases. You press the Add manually button
in the page that appear you must entry all the configuration information of database:
ORACLE_HOME directory
DBSNMP USER
DBSNMP PASSWORD
HOSTNAME
PORT
SID
Check that the dbsnmp user in your database is unlock and press the TEST button to verify the connection work fine.
After this many windows appear of configuration process, and you will put the sys password and host credentials.
If you have problems, tell me
Regards -
Acrobat x standard, using latest win 8, paper sizes Arch A B C D E ... avail when plot to hp plotter, not avail when plot to pdf
any ideas?You mean add custom sizes ?
I just used postscript sizes in my CAD program, and saved a different printer definition file for each, that worked for cad, look into large pdf's tomorrow.
thx jp -
Code insight is not available when eding jsp by using 10.1.3.36.73
I use 10.1.3.36.73 jdeveloper on windows to develop web application,
but code insight is easy not available when editing jsp 2.0.
I must restart jdeveloper and it still isn't often available.
ex. in jsp
ArrayList al = new ArrayList();
for (Iterator it=al.
Code insight is not supported for jsp or this is bug?Do you still have any code error in your jdev editor? no matter the error is JSP or HTML (it is signed by little red box at the right of the window near scroll bar), code insight sometimes is not available.
-
[J2EE Deployment SPI:260003]Feature not available when in disconnected mode
hi am am having this error when trying to deploy my application in portal
[04:40:27 PM] #### Deployment incomplete. ####
[04:40:27 PM] [J2EE Deployment SPI:260003]Feature not available when in disconnected mode.
#### Cannot run application HR-Portal due to error deploying to IntegratedWebLogicServer.
[Application HR-Portal stopped and undeployed from Server Instance IntegratedWebLogicServer]
my log error
[04:29:53 PM] Wrote Archive Module to C:\JDeveloper\mywork\HR-Portal\PortalWebAssets\deploy\PortalWebAssets.jar
[04:40:08 PM] oracle.rc.asadapter.connection.ConnectionException: Cannot establish connection.
[04:40:08 PM] at oracle.rc.asadapter.weblogic.connection.spi.Weblogic10Jsr160Provider.getPresentation(Weblogic10Jsr160Provider.java:73)
[04:40:08 PM] at oracle.rc.asadapter.connection.AppServerConnectionImpl$PM.getPresentation(AppServerConnectionImpl.java:171)
[04:40:08 PM] at oracle.rc.asadapter.connection.AppServerConnectionImpl.getPresentation(AppServerConnectionImpl.java:66)
[04:40:08 PM] at oracle.jdevimpl.deploy.jazn.JaznDataDeployerListener.uploadIdentities(JaznDataDeployerListener.java:234)
[04:40:08 PM] at oracle.jdevimpl.deploy.jazn.JaznDataDeployerListener.uploadIdentities(JaznDataDeployerListener.java:217)
[04:40:08 PM] at oracle.jdevimpl.deploy.jazn.JaznDataDeployerListener.willDeploy(JaznDataDeployerListener.java:97)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.ListenerSupport.fireWillDeploy(ListenerSupport.java:198)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:88)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.WrappedDeployer.deployImpl(WrappedDeployer.java:39)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.DeploymentManagerImpl.deploy(DeploymentManagerImpl.java:457)
[04:40:08 PM] at oracle.jdeveloper.deploy.DeploymentManager.deploy(DeploymentManager.java:217)
[04:40:08 PM] at oracle.jdevimpl.deploy.common.ModulePackagerImpl.deployProfiles(ModulePackagerImpl.java:86)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.ModulePackager.deployProfiles(ModulePackager.java:63)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.ModulePackager.deployImpl(ModulePackager.java:52)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.WrappedDeployer.deployImpl(WrappedDeployer.java:39)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.BatchDeployer.deployImpl(BatchDeployer.java:82)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.WrappedDeployer.deployImpl(WrappedDeployer.java:39)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.BatchDeployer.deployImpl(BatchDeployer.java:82)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.WrappedDeployer.deployImpl(WrappedDeployer.java:39)
[04:40:08 PM] at oracle.jdeveloper.deploy.common.AbstractDeployer.deploy(AbstractDeployer.java:94)
[04:40:08 PM] at oracle.jdevimpl.deploy.fwk.DeploymentManagerImpl.deploy(DeploymentManagerImpl.java:457)
[04:40:08 PM] at oracle.jdeveloper.deploy.DeploymentManager.deploy(DeploymentManager.java:217)
[04:40:08 PM] at oracle.jdevimpl.runner.adrs.AdrsStarter$7$1.run(AdrsStarter.java:1774)
[04:40:08 PM] Caused by: java.io.IOException
[04:40:08 PM] at weblogic.management.remote.common.ClientProviderBase.makeConnection(ClientProviderBase.java:196)
[04:40:08 PM] at weblogic.management.remote.common.ClientProviderBase.newJMXConnector(ClientProviderBase.java:84)
[04:40:08 PM] at javax.management.remote.JMXConnectorFactory.newJMXConnector(JMXConnectorFactory.java:338)
[04:40:08 PM] at oracle.rc.asadapter.weblogic.connection.spi.Weblogic10Jsr160Provider.getPresentation(Weblogic10Jsr160Provider.java:67)
[04:40:08 PM] ... 28 more
[04:40:08 PM] Caused by: javax.naming.NamingException [Root exception is java.rmi.UnexpectedException: Marshalling: ; nested exception is:
[04:40:08 PM] java.rmi.ConnectException: Could not establish a connection with -3508319463259142590S:127.0.0.1:[7101,7101,-1,-1,-1,-1,-1]:DefaultDomain:DefaultServer, java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination; nested exception is:
[04:40:08 PM] java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination]
[04:40:08 PM] at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:86)
[04:40:08 PM] at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:32)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.toNamingException(WLInitialContextFactoryDelegate.java:788)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.pushSubject(WLInitialContextFactoryDelegate.java:685)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.newContext(WLInitialContextFactoryDelegate.java:469)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:376)
[04:40:08 PM] at weblogic.jndi.Environment.getContext(Environment.java:315)
[04:40:08 PM] at weblogic.jndi.Environment.getContext(Environment.java:285)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactory.getInitialContext(WLInitialContextFactory.java:117)
[04:40:08 PM] at javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:667)
[04:40:08 PM] at javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:288)
[04:40:08 PM] at javax.naming.InitialContext.init(InitialContext.java:223)
[04:40:08 PM] at javax.naming.InitialContext.<init>(InitialContext.java:197)
[04:40:08 PM] at weblogic.management.remote.common.ClientProviderBase.makeConnection(ClientProviderBase.java:178)
[04:40:08 PM] ... 31 more
[04:40:08 PM] Caused by: java.rmi.UnexpectedException: Marshalling: ; nested exception is:
[04:40:08 PM] java.rmi.ConnectException: Could not establish a connection with -3508319463259142590S:127.0.0.1:[7101,7101,-1,-1,-1,-1,-1]:DefaultDomain:DefaultServer, java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination; nested exception is:
[04:40:08 PM] java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination
[04:40:08 PM] at weblogic.common.internal.BootServicesStub.authenticate(BootServicesStub.java:57)
[04:40:08 PM] at weblogic.security.acl.internal.RemoteAuthenticate.authenticate(RemoteAuthenticate.java:90)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.authenticateRemotely(WLInitialContextFactoryDelegate.java:747)
[04:40:08 PM] at weblogic.jndi.WLInitialContextFactoryDelegate.pushSubject(WLInitialContextFactoryDelegate.java:679)
[04:40:08 PM] ... 41 more
[04:40:08 PM] Caused by: java.rmi.ConnectException: Could not establish a connection with -3508319463259142590S:127.0.0.1:[7101,7101,-1,-1,-1,-1,-1]:DefaultDomain:DefaultServer, java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination; nested exception is:
[04:40:08 PM] java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination
[04:40:08 PM] at weblogic.rjvm.RJVMImpl.getOutputStream(RJVMImpl.java:352)
[04:40:08 PM] at weblogic.rjvm.RJVMImpl.getRequestStreamForDefaultUser(RJVMImpl.java:689)
[04:40:08 PM] at weblogic.common.internal.BootServicesStub.authenticate(BootServicesStub.java:50)
[04:40:08 PM] ... 44 more
[04:40:08 PM] Caused by: java.io.IOException: Destination unreachable; nested exception is:
[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination
[04:40:08 PM] at weblogic.rjvm.RJVMImpl.ensureConnectionEstablished(RJVMImpl.java:334)
[04:40:08 PM] at weblogic.rjvm.RJVMImpl.getOutputStream(RJVMImpl.java:350)
[04:40:08 PM] ... 46 moreCaused by: java.io.IOException: Destination unreachable; nested exception is:
+[04:40:08 PM] java.net.ConnectException: Connection refused: connect; No available router to destination+
Is the WebLogic server running? -
Commenting functionality not available when I open a pdf in air application
commenting functionality not available when I open a pdf in
air application. Adobe documentation says that is expected with
adobe air 1.0 but I still have the same problem even if I use the
latest air runtimeBack up all data.
In the Finder, select Go ▹ Go to Folder from the menu bar, or press the key combination shift-command-G. Copy the line of text below into the box that opens, and press return:
/Library/Internet Plug-ins
From the folder that opens, remove any items that have the letters “PDF” in the name. You may be prompted for your login password. Then quit and relaunch Safari, and test.
I've seen an unconfirmed report that the "Silverlight" web plugin distributed by Microsoft can also interfere with PDF display in Safari, so you might need to remove it as well, if applicable.
If you still have the issue, repeat with this line:
~/Library/Internet Plug-ins
If you don’t like the results of this procedure, restore the items from the backup you made before you started. Relaunch Safari again.
Maybe you are looking for
-
The apple genius said I can easily buy one online and a 10 year old could put it in. However, all of the hard drives I'm seeing mention PC rather than Mac.
-
How much does it cost to replace the home button
My ipad mini is out of warranty. Any ideas how much it may cost to repair the home button at the Apple Store?
-
None of the information from the iphone calendar has uploaded?
I have been able to upload all my contacts, (with full postal addresses) from my iphone4 to icloud...but none of the information from the iphone calendar has uploaded? Can anyone please advise? Regards, Laurance
-
Reinstall CS5 Design Premium Student & Teacher with Acrobat
I purchased Adobe Creative Suite 5 Design Premium Student and Teacher Edition as a University staff member. I recently had a HDD failure and have had to reinstall all my software. I managed to find CS5 Design Premium and downloaded and installed it b
-
Landed Cost : Journal Entry
Hello every body. Something rare is happening to me when I try to make a Landed Cost Journal Entry. Normally, when I try to do this, the journal entry it comes with just One account (inventory account), but this especial one is coming with 2 accounts