Still cant get 400mhz to work

why is my ddr clock set to 333mhz when i have got 400mhz memory ..........I cant change it it is greyed out ....have tried changing settings in dram settings as well

Try this. If not check Ram, Board or both.
Good Luck!
dbacso
You said....
I do not understand your terminology my bios has these settings
Configure DRAM timings by SPD Enabled (Set to Disable)
DRAM CAS# Latencey_ _ _ _ _ _ 2 (Set to 2.5)
DRAM RAS# Precharge _ _ _ _ _ 2 (Set to 3)
RAS# to CAS# Delay_ _ _ _ _ _ 2 (Set to 3)
Precharge Delay _ _ _ _ _ _ _ _ 5 (Set to 6)
Burst Length_ _ _ _ _ _ _ _ _ _8
Integrity Mode_ _ _ _ _ _ _ _ _ DISABLED
>Frequency/Voltage control
CPU Ratio Selection_ _ _ _ _ _ LOCKED
DRAM Frequency _ _ _ _ _ _ _ AUTO (Set to Manual)
Spread Spectrum _ _ _ _ _ _ _ DISABLED
Adjust CPU Bus Clock(MHz) _ _ 200 Thanks Mob!
DDR Clock(MHz)_ _ _ _ _ _ _ _ 333 (grey and wont change) (Hopefully in luck!)
Adjust AGP/PCI Clock(MHz) _ _ 66.66/33.33
CPU Vcore Adjustment_ _ _ _ _ NO
CPU Vcore_ _ _ _ _ _ _ _ _ _ _ 1.5500v
DDR Power Voltage _ _ _ _ _ _ 2.65v
AGP Power Voltage _ _ _ _ _ _ 1.6v

Similar Messages

I installed Aperture from the App Store, it was working ok, then suf=ddenly it wont load, I get the "Aperture encountered problem" message, have updated all OSX and Aperture but I still cant get it to work, any ideas ?

I installed Aperture from the App Store, it was working ok, then suf=ddenly it wont load, I get the "Aperture encountered problem" message, have updated all OSX and Aperture but I still cant get it to work, any ideas ?

I installed Aperture from the App Store, it was working ok, then suf=ddenly it wont load, I get the "Aperture encountered problem" message, have updated all OSX and Aperture but I still cant get it to work, any ideas ?

Ok, very new , but still cant get it to work .

hi, everyone, i have an older wvc54gc ver.1-1 that i bought on ebay, did NOT come with the CD, but found on this forum, what todo with missing CD, here was the link
http://homecommunity.cisco.com/t5/Cameras/Missing-setup-CD-ROM-for-WVC54GC/td-p/298310but
this is my question, my main comouter at home has Vista on it, my remote computer has XP on it, i have a dlink router, i had the cam working for a minute on my remote computer, and when i had to reboot, i lost everything,... the cam was plugged into the remote cam , unplug and nothing works, any great suggestions for this,
i would just like to get this cam set up at home, and when i am away i can see whats going on..
any first steps again ?
i saw a few programs out there for monthly cost, but still like the linksys cam for free..
will this linksys cam work on Vista ?
anyone have a link to download the software ?
tried the cisco site and they said the firmware will not work cause the cam is out of waranty.
help..
thanks for your support.
alex

You should be able to do a google search to find the latest firmware for that camera. Looks like it is Version 1 (and they are up to Version 3 now).
I would start by updating the firmware.
Did you set your camera to have a static IP address? I struggled A LOT with this as I am not a network type guy, but what I found most helpful was to set a static IP address on the camera (and set one outside the normal range) (I used 192.162.1.67). Rebooting routers, etc, caused all of your DHCP ip addresses to renew and change, and I *think* that I was ending up with IP address conflict of some sort.
A real network expert might be able to help more.

Still cant get it to work ?????? jTable Error

Hi All,
not to sure how to put the problem but here goes
i have been working on a problem using a JTable
and MYSQL database and the information is coming
up twice. i am using abstractTableModel.
i am just wondering if there is something a have over looked
if any one can help me it will Much appreciated
JJ

and the information is coming up twice.
Then you are adding the information to the TableModel twice.
i am using abstractTableModel. No you aren't. You are using some class that extend AbstractTableModel. I would suggest you use the DefaultTableModel so you don't have to write your own TableModel.
Simple example:
http://forum.java.sun.com/thread.jspa?forumID=57&threadID=5123381

Still cant get my ipod to work...

My earlier post: http://discussions.apple.com/thread.jspa?threadID=971361
I still cannot get it to work, I have tried everything. I have reset and restored my ipod multiple times. Thinking about sending it back soon. I get that same error every time I try and put music on my ipod, sometimes it works...and sometimes it wont. Sometimes I cant get a certain song to go on, and then another time it will.
All my music was on my computer before I had my ipod. It was all either from cds or downloaded. A friend has also sent me tons of music that works on his ipod fine.
I have always used Winamp to listen to my music, and still do. Could that have anything to do with it? Or made it another format?
Very annoying, anyone have any clues?
Windows XP Pro

Did you read the link that StarDeb55 provided? It sounds like a local disk problem. Can the Windows Defrag utility run with out errors? Is your music library shared? i.e. Do multiple applications use the files. Like say Windows Media Player and iTunes. If so the other program(s) may be locking the file(s) preventing iTunes from coping it.
P.S. If you are new to forums creating duplicate threads is generally considered a no-no and makes it less likely that people will respond to your post.

I have set up a apple id and i still cant get my imessage or facetime to work?

Set up a apple id and still cant get my fact time or i message to work

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

My apple ID password works for all of my devices but one. i only have one account and have changed the password several times but still cannot get it to work on my iPhone. any suggestions would be appreciated.

My apple ID password works for all of my devices but one. i only have one account and have changed the password several times but still cannot get it to work on my iPhone. any suggestions would be appreciated.

Thanks for the suggestion, Chris. I actually did not resolve the issue which is why i did not post an answer.
it turns out that my iphone seems to default to an incorrect User ID (it defaults to an @me account, which is not something that i have ever used).
even when i change the User ID in my settings for the iTunes store, it still appears when i attempt to get updates for my existing apps. however, it does seem to use the correct ID when i attempt to purchase new apps.
If someone actually had an answer to correct this, i would love to update my existing apps.
Thank you.

I cant get itunes to work on my new Sony Vaio. Im running Windows 8.1.

i cant get itunes to work on my new Sony Vaio. Im running Windows 8.1. Anyone have a fix?

Hello philtapevans,
The following article provides information and steps that can help get iTunes installed on your computer.
Issues installing iTunes or QuickTime for Windows
http://support.apple.com/kb/HT1926
Cheers,
Allen

Set up ipod touch to cox email, ive tried everything and cant get it to work. thanks!

set up ipod touch to cox email, ive tried everything and cant get it to work. thanks!

Here's an answer from the net:
Go to Settings/Mail,contacts,calendars/Add account choose other, choose Add Mail Account. Fill in name, email address, password and description on the screen that comes up. Save those.
One the next screen tat comes up click om POP in the first line then fil in the host name as
spop.west.cox.net or spop.east.cox.net or the one to go with your region.
Note that is not a misprint, that is spop (secure pop)
Fill in your username one more time (the password should have carried over from previously)
Fill in your outgoing mail server like smtp.west.cox.net (change for your region) and click Save.
When all the settings are verified a checkmark will appear next to them all and you are good to go.
If it says something like "can't connect via SSL would you like to ..." then you probably missed the step about selecting POP on the second screen and are trying IMAP so go back and try over with POP. Or perhaps mistyped soemthing.
Once everything is working you can go back into the settings and see that it has automatically connected on port 995 and that SSL is on
Note that you probably won't be able to send email from a wifi in a cafe or similar as cox won't let you connect to their smtp from outside their network.
I haven't tried receiving mail from a non cox connected wifi yet but I suspect it will work just fine. Anyway these settings work for me using my ipod to my home wifi router connected to cox.
I could not find a definitive guide when I searched so I hope this helps other folks trying to configure this.
I got the spop from "Mail for Mac OS X 10.5 configure SSL / POP" here:
http://support.cox.com/sdccommon/asp...c-7f95e8bcaf39

HT1212 i have tried all of the suggested things still cant get in the ipod

i have tried all of the suggested things and still cant get in the ipod

As instructed in the If you have never synced your device with iTunes, or you do not have access to a computer section of the article, put it in recovery mode and restore:
Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
Continue holding the Home button until you see the Connect to iTunes screen.
iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device.

Apple Please sort out the V 11.1.4 problems as I cant get iTunes to work now. You need to have a new version asap

Please sort out the V 11.1.4 problems as I cant get iTunes to work now. You need to have a new version asap

Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2

I cant get ECWID to work on my mobile devices, it only seems to use the desktop site rather that the Tablet or iPhone

I cant get ECWID to work on my mobile devices, it only seems to use the desktop site rather that the Tablet or iPhone? Can anyone help me?

Hi Jim,
We’ll be glad to help you.
Ecwid supports responsive layout, which means that the store pages can adapt to the visitor's screen width on the fly and keep the layout clean and nice. Your products and categories lists will be fit for any window's size, as Ecwid will calculate the most suitable number of products or categories in row automatically. In other words, Ecwid looks great on any mobile devices. You can check how your Ecwid store may look on smartphones and tablets, if you see your Starter Site (what it is).
However, if you want Ecwid reveals itself in all its glory, you should embed your Ecwid store into website, which also support responsive layout, because if the site doesn’t adapt to size screen, Ecwid is not able to determine how it should be changed since it’s just a part of the site.
We’ve checked your site and found that you used Adobe Muse for building your site. Using Adobe Muse, you can create alternate site layouts for web content to be displayed on desktop, smartphones, and tablets. Nonetheless, your site has a layout for desktops only, that’s why it looks the same on all devices. You can learn how to create those alternate layouts in Adobe Muse, by reading “Creating a Website for Mobile Devices” article.
I hope this helps! But if there are any questions, don’t hesitate to reach us out on Ecwid forums.

Cant get Frontrow to work after installing 10.4.3 and updating it

I made a terrible mistake today and moved all my files from my harddisk to my external harddisk. I had to reinstall everything but I cant get frontrow to work properly. I cant find it on my external harddisk either.
Can someone please help me with this tricky question.

Winbo:
Can you describe your problem in a bit more detail? Why did you decide to move your files? What files did you move? What method did you use to move them? Did you move them over completely by way of backing up and then erased your disk prior to moving them back?
Any other information you can provide will make it easier to make suggestions on your issue.
Good luck.
cornelius
PismoG4 550, 100GB 5400 Toshiba internal, 1 GB RAM; Pismo 500 OS X (10.4.5) Mac OS X (10.4.5) Beige G3 OS 8.6

Cant get facetime to work on mini ipad

Cant get FaceTime to work on new mini IPad....any suggestions? It keeps verifying but it will not work, it allows me to get apps. Triple checked that the Apple ID and password is correct, checked the settings to make sure they are turned on, able to get imessage, not sure what the problem could be?

Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
iOS: FaceTime is 'Unable to verify email because it is in use'
http://support.apple.com/kb/TS3510
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
iOS 6 and OS X Mountain Lion: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
How to Set Up & Use iMessage on iPhone, iPad, & iPod touch with iOS
http://osxdaily.com/2011/10/18/set-up-imessage-on-iphone-ipad-ipod-touch-with-io s-5/
Extra FaceTime IDs
http://tinyurl.com/k683gr4
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Troubleshooting iMessage Issues: Some Useful Tips You Should Try
http://www.igeeksblog.com/troubleshooting-imessage-issues/
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Fix Can’t Sign Into FaceTime or iMessage iOS 7
http://ipadtutr.com/fix-login-facetime-imessage-ios-7/
FaceTime, Game Center, Messages: Troubleshooting sign in issues
http://support.apple.com/kb/TS3970
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
How to Block Someone on FaceTime
http://www.ehow.com/how_10033185_block-someone-facetime.html
My Facetime Doesn't Ring
https://discussions.apple.com/message/19087457
Send an iMessage as a Text Message Instead with a Quick Tap & Hold
http://osxdaily.com/2012/11/18/send-imessage-as-text-message/
To send messages to non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
How to Send SMS from iPad
http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
You can check the status of the FaceTime/iMessage servers at this link.
http://www.apple.com/support/systemstatus/
 Cheers, Tom

Cant get bluetooth to work on iphone 5 wont even discover divices

Cant get bluetooth to work on iphone 5 wont even discover divices

supported bluetooth profiles http://support.apple.com/kb/ht3647
what are you trying to connect your device to?

Still cant get 400mhz to work

Similar Messages

Maybe you are looking for