Still Monitor in Yellow
Hi
i Ran the Init. Delta without Data transfer from ODS to other ODS and Cubes. In Manage Data Target it showing Green Symbol(No Report Symbol) , But in Monitor still it is in Yellow for long time , please some tell me how would i proceed further
Version : BW 3.1
Thanks,
GAL
Hi,
yeah,make the request status to Green Manually...
when its done successfully..the reporting symbol will be updated at Cube Level...
But when it comes to DSO..you will have to activate the data to enable it to available for reporting.to do this..select your DSO at infoprovider section of the RSA1-->right click to get context menu->Manage->now select your request-->press activate.
once if the data is activated at request level,then the data is available for reporting.
hope this is clear for you.
Regards
Ramsunder
Similar Messages
-
AX light is yellow and does not flash and doesn't change even when I press the "reset". Tried unplugging and reset -- still a solid yellow. I assume this is a goner?
Unfortunately, based on your description, I would have to second that your Express is a "goner." However, before giving up on the unit, be sure that you attempt a "factory default" reset at least 3x just to be sure.
-
i am having trouble with exchange account connection .the vpn connects fine but the exchange account is still showing the yellow light .can anyone help?
I had a similar problem. Here is how I resolved the issue.
1. Remove Network Connect
2. Run Terminal and remove /usr/local/juniper and everything within the juniper directory.
3. Reboot the machine and reinstall Network Connect
4. Test if you can now connect.
During removal, you may encounter permission denied error, you will need to change the permission to 777. For example "sudo chmod 777 nc". -
VGA external monitor shows yellow and green colour
I just took apart my T410s to change the screen hinges. I thought all had gone well but when I plug in an external monitor the colours don't display properly. The display is yellow and if you wiggle the cable it goes green. Could this have been something I did? It worked fine before.
Any ideas how to fix it?
Thanks
AndyHi, arp1981
I have a question for clarification: Does this only occur on an external monitor, not the laptop's display itself? If so, then I would retrace your steps of replacing the hinges and make sure that all wires and devices are where they should be. Also, check the pins on the VGA cord and the VGA port itself and make sure nothing is bent.
Best,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it. -
2nd monitor has yellow cast it never had before
I've been using a Dell 2405FPW monitor as my main screen for years, and the brightness and color was always great. Now that I have a new 24" iMac, I'm using the Dell monitor as a second screen, and it has a terrible yellow cast. I can't get rid of it with the monitor's controls, or with the Calibration tool in the Displays control panel. I'm using a Mini DVI-to-DVI adapter between the iMac and the Dell monitor. What's causing this?
Message was edited by: Kris HuntNope, everything is brand new and looks fine. In fact, I now have the exact same setup (24" iMac and 24" Dell 2405 LCD) at home, and I'm seeing the exact same problem there, too. The Dell monitor is bright on its own, but has a dull yellow cast when connected to the iMac with the Mini-DVI to DVI connector.
-
Dear Everyone,
About 5 days ago my powerbook monitor started showing red as yellow and black as green. The computer works the same(perfectly). But the display is hard to read. I certainlky can't do any work in Aadobe. Maybe you would say there is no contrast in the display. Anyway I can find where I can change the calibration.Hmm. It doesn't quite sound like you've switched to "White on Black" mode in the Universal Access control panel in System Preferences.
How many colors is your display set to in the Displays control panel? Under the Color tab, what profile is selected? -
Satellite Pro L300 - External monitor has yellow tinge to screen
I have connected a new external monitor to my Sat Pro L300 and the ext. monitor has a strong yellow tinge to the display.
I have tried it with other monitors and cables and they do the same ie yellow display.
Can anyone suggest anything I can do, I have tried changing all colour settings but they do not get rid of the yellow tint.
thanks.Well, possibly this issue is related to the hardware malfunction since the display should show common colors without changing any settings in Color Settings in the Graphics Card Control Panel
So in my opinion its hardware issue
However, before asking a technician for a opinion I recommend updating the BIOS and reinstalling the graphic card driver. -
Hi:
My monitor has a yellowish hue in color instead of white. This is on a HP desktop that I purchased about 6 months ago. It just happened the other day. Can you tell me how to fix it?Hi vaemp1,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I see that the monitor you have connected to your desktop is displaying a yellowish discoloration instead of white, and I would be happy to guide you towards a resolution! To begin, I will need to ask you a few questions:
What is the Product and Model Number of your desktop computer and monitor?
What version of Windows do you have installed on your computer?
Has your computer completed all of its important Windows Updates?
Is this an on-going, or recent issue?
In the meantime, please follow this document on Display Quality Issues regarding screen discoloration. This should help determine if your monitor has a hardware issue or not.
Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping! -
My screen is dark> Have checked brightness under sys preferences/displays and it is on highest setting.
Also checked this using the F2 key. It too is on highest setting. Still not bright...
HELPWe usually advice first to Reload web page(s) and bypass the cache in case of such problem and then do a check for extensions to see if any are causing the problem.
* Press and hold Shift and left-click the Reload button.
* Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
* Press "Cmd + Shift + R" (MAC)
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes
Other possible causes can be zooming a page or having increased the minimum font size.
*http://kb.mozillazine.org/Websites_look_wrong -
No monitor profile available. Yellow tint after import
Hello. I have bough last week a new Toshiba notebook which has Windows 8.1 preinstalled on it.
I have noticed a problem that seems other came also on the same issue. When i watch images on a non profile managed software, the images look fine. Once i import them on Lightroom or Photoshop, the images get a yellow tint.
The problem and a possible solution is also described here: http://photography-on-the.net/forum/showthread.php?t=1164320 . This is setting the sRGB as a monitor profile. I know this is not a great solution, but surely better than what i see on my monitor. In any way, this unfortunately this did not work for me.
This is what i mean with the yellow tint (left Lightroom, right Irfan)
Today i tried following:
Step 1
The image is in RAW format. I import it in Lightroom and gets that yellow tint i described.
I export it with sRGB in jpg format. The jpg file has still that yellow tint. Please note here, that others that report similar problems, they mention that after the export they image looks again fine.
Step 2
I open the RAW image with Irfan (not color managed) and save it as jpg. The image is saved "correctly", as you see on the right side of the image above.
Step 3
I import the exported jpeg that was created with Irfan and import it to Lightroom.
The yellow Tint now does not appear on the imported JPEG.
One more tip i can give is: When i do a Soft proofing on Lightroom and choose sRGB i still see that yellow tint.
What exactly is happening ? I try to identify the problem. Why i see just raw images with this yellow tint, no matter the profile i set for my monitor and no matter the proofing options on lightroom.
I don't want to spend 100+ euro for a calibration device and not being able to use the profiles.
Any suggestions for further testing ?First - Irfanview needs to be at least IV 4.35 and needs to have the LCMS.DLL plug-in installed as well as having the Color Management enabled so that you have some chance of your Photoshop and IrfanView versions of an image matching:
Alright we have the first conflict here.
I have the latest IrfanView version (4.37) , i saw that the Lcms.dll exists in the plugin list, and i have set the settings as suggested.
Furthermore at the moment i have sRGB as my default monitor profile. Still this is how i see things.
IrfanView and Photoshop have the same difference as before. Yes i have rerasted IrfanView on every change. I actually freshly installed also the latest irfanView version with its plugin.
Photoshop - Irfan Side by Side
Monitor Profile Settings 1
Monitor Profile Settings 2
IrfanView Settings
About this
As you can see the Adobe default processing with the Adobe Standard profile, at top left, is a little greenish. This is compared to the default camera processing as viewed in the camera-embedded preview jpg from the CR2 at the bottom right which a white frame around it.
When i open the raw image on LR, i have (from what i can see on my monitor) the same results as your Adobe default processing (Top left) . What confused me on your image above is bottom left image "Adobe processing - Camera standard". What is with Adobe processing meant here? The camera profile? If yes then how can we have Adobe camera profil but also camera standart ? If you mean the process LR provides, mine is set on 2012. But no adobe available for selection. I do not know if this is meant though.
Here is my comparison between Adobe Standart Profile and Camera Standard.
LR: Adobe Profile vs Canon Standart Profile
One more comparison is of the files you made available including the IranView jpg you supplied as compared to the Canon JPG preview that I extracted from the CR2 file:
What you can see is that the CR2 as viewed in LR and LR's exported JPG of that CR2 look about the same (top and bottom left), and the IrfanView and Canon-JPG versions of the CR2 look the same (top and bottom right). This is your IV version of the JPG, not something I made, but I expect IV has just extracted the camera-embedded fullsize preview JPG from the CR2 file just like I did using a different tool, so they look the same, but it is possible your IV is using a Canon-specific plug-in that uses the Canon-supplied SDK library DLLs that can also duplicate Canon processing. I only have the Formats.dll and the CRW.dll but not all the extra SDK DLLs so I expect my IV is only extracting the camera-embedded preview JPG.
Yes i can confirm that also on my environment. The exported CR2 from LR matches the exported JPG as also there is a match between IrfanView CR2 with the Camera standard profile export. Unfortunately i cannot confirm if IrfanView uses a sort of Canon-plugin to make the RAWS rendered automatically with the Canon standard profile.
And if you want your Adobe treatment of CR2 files to look much more similar to your camera's treatment, then use the Camera Standard profile in Lightroom and the PS ACR plug-in.
Question on this. Should i always put a Camera Standart profile on all my images after importing them on LR ?
Also please, let me know what you meant with Adobe Processing. I searched on the web with "Adobe Processing lightroom" , but i could not understand what is meant.
If using the Camera Standard profile doesn't make things look almost the same, then please post a side-by-side of LR's view of the CR2 and IrfanView's JPG extracted from the CR2--what you've linked to, just above.
Here is a comparison between an exported JPG from Lightrom with camera profile (Right) compared to an exported JPG with IrfanView from the RAW (left). As mentioned before the images look identical, with the one exported from LR with Camera profile being a bit more vibrant. But not much of a difference.
IrfanView vs Camera Profile export
So in the end it seems you see also that green-yellowish cast on the RAW image. From what i see on the screenshots you made.
The question now is why i do not see RAW the same as Adobe software ? Could i do this test with an other viewer?
To summerize from my side as well. A monitor calibration is surely good to do. On the other side the cast i see on the RAW in this case has not to do with the profile but rather with Adone profile and the way this image was captured.
PS. I must admit that is one of the best on line support i have ever seen. Thumbs up ssprengel ! -
Yellow Cast to HVX200 Footage in FCP - but fine on NTSC Monitor
Dear Folks:
I am shooting two cameras with an HVX200 and an HMC150 in a room where the only light source is daylight-bulbed Kinoflos. The lights are fixed, as it the set. Nothing changes. There are no windows.
I have two NTSC monitors, both set to camera bars.
I use manual white balance. I use a big white card (a foamcore board).
The first day, the image looked perfectly white balanced on the NTSC monitors. We ingested the footage through Final Cut Pro. It matched the look we saw on the NTSC monitors on several macs.
The second day, however, the image had a YELLOW cast to it when ingested via Log and Transfer.
Why would it look clean and white on the NTSC monitors and yellow on various macs?
Thanks!First off, are you saying there is a difference between Day One and Day Two...? or...
Just a difference between NTSC and mac display?
Are there any common values in the days that can be sampled and compared numerically? For example some thing "white" in day one is R=235, G=235, B=235 and on day two is R=235, G=235, B=190?
Two other things off the top of my head might be the white balance went away overnight (if you didn't balance again on the second day), or one of your kinos went "sour".
Not likely but you may be getting a subtractive dynamic contrast in the shadows?
Or, more likely, there is a white point difference between the NTSC monitors and the macs. Generally speaking, most macs set for broadcast-emulation sit around D65, while many, many ntsc monitors can range from D65 all the way up to about 9500, which is VERY blue, but your eye-brain adapts to that and then it becomes a VERY bright "white".... against which everything else will look yellow.
jPo -
Unable to start java engine: dispatcher status is "yellow" in windows2003
Hi Gurus,
we have installed ECC6 in windows 2003.
we are getting an error while starting java engine, dispatcher node is in yellow colour with a message
"J2EE status info unavailable"
and dev_disp says "<<
trc file: "dev_disp", trc level: 1, release: "700"
sysno 04
sid ECC
systemid 560 (PC with Windows NT)
relno 7000
patchlevel 0
patchno 146
intno 20050900
make: multithreaded, Unicode, optimized
pid 3688
Wed Apr 22 18:22:22 2009
kernel runs with dp version 232000(ext=109000) (@(#) DPLIB-INT-VERSION-232000-UC)
length of sys_adm_ext is 576 bytes
SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (04 3688) [dpxxdisp.c 1243]
shared lib "dw_xml.dll" version 146 successfully loaded
shared lib "dw_xtc.dll" version 146 successfully loaded
shared lib "dw_stl.dll" version 146 successfully loaded
shared lib "dw_gui.dll" version 146 successfully loaded
shared lib "dw_mdm.dll" version 146 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3904
Wed Apr 22 18:22:25 2009
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0000.qqq.nxst) took 3 seconds
Wed Apr 22 18:22:29 2009
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 4 seconds
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5371]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >ECC6_ECC_04 <
DpShMCreate: sizeof(wp_adm) 18672 (1436)
DpShMCreate: sizeof(tm_adm) 4270848 (21248)
DpShMCreate: sizeof(wp_ca_adm) 24000 (80)
DpShMCreate: sizeof(appc_ca_adm) 8000 (80)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528056/528064
DpShMCreate: sizeof(comm_adm) 528064 (1048)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (96)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (72)
DpShMCreate: sizeof(vmc_adm) 0 (1544)
DpShMCreate: sizeof(wall_adm) (38456/34360/64/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 09310040, size: 4930904)
DpShMCreate: allocated sys_adm at 09310040
DpShMCreate: allocated wp_adm at 09312090
DpShMCreate: allocated tm_adm_list at 09316980
DpShMCreate: allocated tm_adm at 093169B0
DpShMCreate: allocated wp_ca_adm at 097294B0
DpShMCreate: allocated appc_ca_adm at 0972F270
DpShMCreate: allocated comm_adm at 097311B0
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 097B2070
DpShMCreate: allocated gw_adm at 097B20B0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 097B20E0
DpShMCreate: allocated wall_adm at 097B20E8
Wed Apr 22 18:22:30 2009
MBUF state OFF
DpCommInitTable: init table for 500 entries
ThTaskStatus: rdisp/reset_online_during_debug 0
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation view
<EsNT> Using memory model view.
<EsNT> Memory Reset disabled as NT default
<ES> 511 blocks reserved for free list.
ES initialized.
J2EE server info
start = TRUE
state = STARTED
pid = 5052
argv[0] = F:\usr\sap\ECC\DVEBMGS04\exe\jcontrol.EXE
argv[1] = F:\usr\sap\ECC\DVEBMGS04\exe\jcontrol.EXE
argv[2] = pf=F:\usr\sap\ECC\SYS\profile\ECC_DVEBMGS04_ECC6
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=65000
argv[5] = -DSAPSYSTEM=04
argv[6] = -DSAPSYSTEMNAME=ECC
argv[7] = -DSAPMYNAME=ECC6_ECC_04
argv[8] = -DSAPPROFILE=F:\usr\sap\ECC\SYS\profile\ECC_DVEBMGS04_ECC6
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1633]
***LOG Q0K=> DpMsAttach, mscon ( ECC6) [dpxxdisp.c 11822]
DpStartStopMsg: send start message (myname is >ECC6_ECC_04 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 146
Release check o.K.
DpJ2eeLogin: j2ee state = CONNECTED
Wed Apr 22 18:22:31 2009
***LOG Q0I=> NiIRead: recv (10054: WSAECONNRESET: Connection reset by peer) [nixxi.cpp 4424]
ERROR => NiIRead: SiRecv failed for hdl 4 / sock 480
(SI_ECONN_BROKEN/10054; I4; ST; 127.0.0.1:2089) [nixxi.cpp 4424]
DpJ2eeMsgProcess: j2ee state = CONNECTED (NIECONN_BROKEN)
DpIJ2eeShutdown: send SIGINT to SAP J2EE startup framework (pid=5052)
ERROR => DpProcKill: kill failed [dpntdisp.c 371]
DpIJ2eeShutdown: j2ee state = SHUTDOWN
Wed Apr 22 18:23:10 2009
J2EE server info
start = TRUE
state = STARTED
pid = 4104
argv[0] = F:\usr\sap\ECC\DVEBMGS04\exe\jcontrol.EXE
argv[1] = F:\usr\sap\ECC\DVEBMGS04\exe\jcontrol.EXE
argv[2] = pf=F:\usr\sap\ECC\SYS\profile\ECC_DVEBMGS04_ECC6
argv[3] = -DSAPSTART=1
argv[4] = -DCONNECT_PORT=64999
argv[5] = -DSAPSYSTEM=04
argv[6] = -DSAPSYSTEMNAME=ECC
argv[7] = -DSAPMYNAME=ECC6_ECC_04
argv[8] = -DSAPPROFILE=F:\usr\sap\ECC\SYS\profile\ECC_DVEBMGS04_ECC6
argv[9] = -DFRFC_FALLBACK=ON
argv[10] = -DFRFC_FALLBACK_HOST=localhost
start_lazy = 0
start_control = SAP J2EE startup framework
DpJ2eeStart: j2ee state = STARTED
DpJ2eeLogin: j2ee state = CONNECTED
Wed Apr 22 18:23:11 2009
***LOG Q0I=> NiIRead: recv (10054: WSAECONNRESET: Connection reset by peer) [nixxi.cpp 4424]
ERROR => NiIRead: SiRecv failed for hdl 7 / sock 416
(SI_ECONN_BROKEN/10054; I4; ST; 127.0.0.1:2166) [nixxi.cpp 4424]
DpJ2eeMsgProcess: j2ee state = CONNECTED (NIECONN_BROKEN)
DpIJ2eeShutdown: send SIGINT to SAP J2EE startup framework (pid=4104)
ERROR => DpProcKill: kill failed [dpntdisp.c 371]
DpIJ2eeShutdown: j2ee state = SHUTDOWN
>>
Kindly, help.
Thanks & Regards,
Devender VHi Community,
I have to warm this topic again.
I'm facing the same problem like devender. I followed the posted advices, whithout any change. I also checked note 741289 - no change. I restarted the j2ee engine out of TA SMICM where I also checked the application server's state (j2ee Server Operational = FALSE) - no effect.
In SAPMMC I restarted the instance without any effect. The disp+work.EXE still has a yellow state, says "Running, Message Server connection ok, Dialog Queue time: 0.00 sec, J2EE status info unavailabe.
I think the developer trace says the same like devenders:
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1668]
***LOG Q0K=> DpMsAttach, mscon ( chopin) [dpxxdisp.c 12364]
DpStartStopMsg: send start message (myname is >chopin_EI3_00 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
CCMS: Checking Downtime Configuration of Monitoring Segment.
CCMS: start to initalize 3.X shared alert area (first segment).
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1050]
DpMsgAdmin: Set patchno for this platform to 175
Release check o.K.
Fri Nov 12 11:34:00 2010
DpJ2eeEmergencyShutdown: j2ee state = SHUTDOWN
I followed ravi raj's instructions, so that is the part of the content of dev_jontrol:
[Thr 6844] *** WARNING => JsfOpenShm: ShmCreate (69, 295952, CREATE) failed(rc = 4 SHM segment already exists) [jsfxxshm.c 715]
[Thr 6844] *** ERROR => JsfOpenShm: Shm version mismatch (shm "JSF-ADM-CORRUPT", code "JSF-ADM-015") [jsfxxshm.c 761]
[Thr 6844] *** ERROR => Can't create shared memory segment 69 (rc = 8) [jcntrxx.c 1749]
[Thr 6844] *** ERROR => Can't initialize JControl Administration [jcntrxx.c 273]
[Thr 6844] JControlCloseProgram: started (exitcode = -1)
[Thr 6844] *** ERROR => JsfCloseShm: FiDetachIndex(SESSION) failed (rc = 6 invalid argument) [jsfxxshm.c 1243]
[Thr 6844] *** ERROR => JsfCloseShm: FiDetachIndex(ALIAS) failed (rc = 6 invalid argument) [jsfxxshm.c 1250]
[Thr 6844] *** ERROR => JsfCloseShm: FiDetachIndex(SERVICE) failed (rc = 6 invalid argument) [jsfxxshm.c 1257]
[Thr 6844] JControlCloseProgram: good bye... (exitcode = -1)
Can someone please translate it for me, or give me an tipp what to do?
Thanks in advance,
-ty-
Edited by: Tan Yildiz on Nov 12, 2010 1:38 PM
In the servers process-list (Task Manager) there is no entry for jlaunch (related to [Java Startup und Control Framework|http://help.sap.com/saphelp_NW70/helpdata/de/4f/7ead42c893b211e10000000a155106/content.htm] )
Edited by: Tan Yildiz on Nov 12, 2010 2:18 PM
There's the solution manager running on the same server. In his instance everything's fine.
After changing some instance parameters i'm getting some errors:
1. Parameter Name: jstartup/instance_properties
General standardvalue: $(jstartup/j2ee_properties)$(FILE_SEP)$(jstartup/sdm_propert
Specified standardvalue: D:\usr\sap\EI3\D00\j2ee\cluster\instance.properties;D:\usr\s
2. Parameter Name: exe/j2ee
General standardvalue: (Default)
Specified standardvalue. D:\usr\sap\EI3\SYS\exe\run\jcontrol.EXE
Ok, I think I got it. The specified standardvalues the system is selecting are wrong.....but how can I influence the systems selection?
Edited by: Tan Yildiz on Nov 12, 2010 2:29 PM
Edited by: Tan Yildiz on Nov 12, 2010 2:42 PM -
Process chain remains in yellow for long hours
Hi friends,
My process chain remains in yellow state for many hours.
when i check the the message , it shows as chain has been removed from scheduling. Is that a problem or what may be the problem?
generally if a problem of PC remaining in yellow for long time , what are the Tcodes to be looked into.
regards,
RajeshHi Rajesh
GO to <b>RSPCM</b> check the sataus still its in yellow or green.If it is in yellow then
double clicjk on this it will takes to you in to the chain individually .Then check the
process ..
Or go to <b>RSPC</b> check wher exactly the chain is kicking.Then check the monitor
status of that particular process .This monitor u can achieve By double clicking on
the process-->it will show u a popup in that click on monitor.and then depends on t
the issue u can work and repeat .
Regards
R M K
***Assigning points is the only way of saying thanx in SDN **** -
Why does a jpeg look yellower in Aperture than Preview?
Friend sent a jpeg to me. The image looks much yellower in Aperture than preview.
Exif data regarding color:
Profile Name: sRGB v1.31 (Canon
I have Aperture and preview set to Proofing Profile sRGB 2.1. I have also calibrated my monitor using the display preferences wizard.
Any reason for the yellow cast when I import the image to Aperture?
Any help is appreciated.
Thanks!I have Aperture and preview set to Proofing Profile sRGB 2.1. I have also calibrated my monitor using the display preferences wizard.
Are you saying that you have View->Onscreen Proofing turned on? What if you turn it off and view the image does it still have the yellow cast? -
Regarding Yellow Request Status in InfoCube
Hi All,
I am trying to load the data from DSO to Info Cube. Here DSO is of 7.0 type & InfoCube of 3.x type. Once the data is updated into Info cube, the request is still found in Yellow status. when i checked the monitor of the request, in the status tab all the status are completely green but in the infocube it is still found in yellow status. Also the "Request is available for Reporting" icon is not appearing.
What is the possible cause for the request to remain in yellow status in InfoCube even though the monitor shows Green status. I tried reloading the data completely but still my problem is not solved. Please suggest methods so that request should automatically turn into Green status.
Points will be awarded as per SAP forum rules.
Thanks in advance,
RajeshHi Experts,
I have come up with a new issue.
When I do a full upload from DSO to Infocube, the request in Infocube would remain in yellow status. When i check the monitor status it was completely Green. so in that case i changed the status of request manually to Green as suggested by forum experts.
When I do a INIT upload from DSO to cube, still my request in Infocube would remain in yellow status. Again i changed the status of request manually to Green. But the problem is when i check the monitor of the request, under 'status' tab the status is Green but under 'Details' tab Overall status is still in yellow status. The sub-option 'Databasis (requests) : Not yet finished' is also in yellow status. what is the possible cause for this? how to overcome such problem?
Thanks,
Rajesh
Maybe you are looking for
-
Question says it all.
-
Hi All, I have a picture library with images in sharePoint, now i want display that images in sharepoint webpage as a webpart. i have displayed the all the images as a webpart. Now i want to enable thumbnail on that images and when i click the thumbn
-
Trying to configure syslog process, for Oracle auditing, Oracle 10gR2
Folks, I am trying to use the OS (UNix Sun Solaris 10), syslog process. So I can write my Oracle db 10gR2 audit logs to a location, where Oracle userid on unix cannot modify/delete. For that I have set following values in the Oracle 10gR2 parameters
-
hi how fiscal respondant name should appear on all sales invoices, if If company code is 95 with tax code TC
-
Hello, I have an Intel iMac 20" in January, so it's still covered by the 1-year warranty, plus I already bought an AppleCare Service plan. So, I was just wondering, my Mighty Mouse works fine, except for the fact that the scroll ball doesn't always s