Storage 7310:Cluster Remote Appliance loops during rejoin

Hello,
I performed a takeover on controller A, assigned all resources to that node, then I unconfigured the cluster. Now controller B is trying to rejoin the cluster but fails:
    Sun Storage 7310 Configuration
    Copyright 2009 Sun Microsystems, Inc. All rights reserved.
    NET-0 <=> NET-1 <=> NET-2 <=> NET-3 <=>
    140 error(s) have occurred during cluster rejoin.
    The most recent error was: 'CIO channel not connected'.
    Cluster rejoin will be retried until successful.
    Joining cluster ... /
    ESC-3: Halt   ESC-4: Reboot   ESC-5: Info
    For help, see http://www.sun.com/7310/rebuilding the cluster from controller A does not work in this state:
error: The remote appliance has already been configured. If you wish to
       configure it as part of a cluster, perform a factory reset on it and
       repeat this step.So how to reset controller B? There seems to be no way to perform this task from the screen I posted above.

Problem solved: the kernel boot parameter "-c" does a factory reset during boot.

Similar Messages

Starting Weblogic Server Cluster remotely via VPN

We have a site-to-site VPN setup from our office to our ISP so we can
          control our system remotely. We can stop our Weblogic servers (in a
          cluster) remotely via the VPN no problem via the "stopweblogic.cmd" command
          where we just change the IP address of our remote server. We're having
          trouble starting them through the WebLogic console applet. We can bring the
          applet up & running, but no luck starting them.
          Is there another way to start your weblogic servers (besides using something
          like PC Anywhere).
          Or is there any documentation that could point to an answer here?
          Any suggestions?
          Mike Kendzierski
          B2BGalaxy.com


1. "myserver" is the name of the server. It doesn't want the name of the
machine the server is on.
2. It is possible that something is wrong in the license file. I've made a
typo when changing the license on my server that prevented weblogic from
starting.
Hope this helps.
"Hilmar" <[email protected]> wrote in message
news:[email protected]..
>
When I start WebLogic server using startweblogic.cmd everything seems tobe okay.
Using the 'Start a new WebLogic server or cluster' command from WebLogicConsole
5.1.0, I get the following error message:
Attempting to start server on the machine running the console using
C:\weblogic\jre1_2\jre\bin\java.exe -mx32m -ms32m -classpath"C:\weblogic\jre1_2\jre\lib\rt.jar;C:\weblogic\jre1_2\jre\lib\i18n.jar;C:\we
blogic\lib\i18n.jar;C:\weblogic\classes\boot;C:\weblogic\eval\cloudscape\lib
\cloudscape.jar"
-Dweblogic.class.path=C:\weblogic\license;C:\weblogic\classes;C:\weblogic\myserver\serverclasses;C:\weblogic\lib\weblogicaux.jar
-Dweblogic.system.discardOutAndErr=true -Djava.security.manager -Djava.security.policy==C:\weblogic\weblogic.policy
-Dweblogic.system.name=kenapp00111 -Dweblogic.system.home=C:\weblogic -Dweblogic.cluster.enable=false
-Dweblogic.cluster.name=mycluster -Dweblogic.system.listenPort=7001 -Dweblogic.system.SSLListenPort=7002
-Dweblogic.cluster.multicastAddress=237.0.0.1 weblogic.Server
$$$$$$$$$$$$$$$$ License Exception $$$$$$$$$$$$$$$$
Loaded License : C:/weblogic/license/WebLogicLicense.xml
However Unable to start because :
No License found for WebLogic
As well as the fact that: No License found for Tengah
As well as the fact that: No License found for WebLogic/JDBC
As well as the fact that: No License found for Tengah/JDBC
As well as the fact that: No License found for jdbcKona/T3
Is the 'server name' the name of the machine or 'myserver' ? Could therereally
be something wrong with the licence file ?
Thanks for helping !
Hilmar

Storage 7410 cluster - separating "admin" traffic from "storage" traffic

Please help me figure out a strategy here. We have a Storage 7410 cluster running in an active/passive mode. On each node, I have cabled nge0 and nge1 each to 100Mbps ports and nxge0 and nxge1 to 10Gbps ports. I have configured nge0 to be the "admin" interface for node 1, and nge1 the same for node 2. I have aggregated nxge0 and nxge1 via LACP and it's currently owned by node 1 (fails over to node 2 nicely). Here's the basic layout:
Node 1
nge0 -> active "admin" interface -> ip address 172.16.158.33
nge1 -> inactive (owned by Node 2) "admin" interface
nxge0/nxge -> active LACP aggregate "aggr1" -> ip address 172.16.158.32
Node 2
nge0 -> inactive (owned by Node 1) "admin" interface
nge1 -> active "admin" interface -> ip address 172.16.158.41
nxge0/nxge -> inactive (owned by Node 1) LACP aggregate
What's confusing me is routing. Right now all interfaces have IPs on the same subnet. I can define a default route for the gateway on that subnet (172.16.158.1) on the "aggr1" LACP, but only Node 1 gets routed. So, I can add two additional default routes to the same gateway, reflecting each of the other NICs (nge0, nge1). But the way I understand it, there's no guarantee that IP traffic that originated on aggr1 will return via that same interface. Or am I mistaken? Essentially, I want to segregate "storage" traffic from "admin" traffic, and I want to make sure that any host connecting to the "storage" IP address takes full advantage of the 10Gbps aggregate.
Any ideas are welcome.
Charles

My assumption above was correct. At some point, traffic was now favored over nge0, so my performance went down from ~200MB/s to about 60MB/s (expected results with Windows VMs on vmware with a NFS datastore). It looks like I may have to abandon the nge ports and lose the LACP (at least until I can get a second nxge NIC in each head). Is that all I can do? Any ideas are appreciated.
Charles

Stop Playback Looping During Editing

Can't seem to find where to set the loop/don't loop option. At the end of the timeline, the playback goes to the beginning and starts playback again. I want it to stop at the end and not loop (during editing). Can you help me find the setting to stop it from continuing playback from the beginning of the clip (stop playback looping during editing).
Premiere Elements 10
Win7(64)

There is no direct way to stop playback AT the last Frame.
Does the End key not work on your computer?
Once playback has been stopped, the PageUp and PageDn keys will take you to the first Frame of the last Clip, or to the first Frame of that last Clip. The Cursor keys will also step you, Frame-by-Frame, inside the Clip.
Good luck,
Hunt

How do I specify which Storage DRS Cluster a VM deploys on?

Hi All,
I have tried utilising the VirtualMachine.Storage.Cluster.Name Custom Attribute to get a VM to deploy onto a specific Storage DRS cluster.
This doesn't seem to work though and the VM's are still assigned sporadically.
I am utilising vCAC 6.1 with vSphere as the direct endpoint.
We have a Metro Storage Cluster. Each vSphere cluster has 2 Datastore clusters each.
Has anyone had any success with this or is there an alternate Custom Attribute I should be using?
Regards
Dave

Hi,
Thanks for your response, unfortunately this will not work in my situation.
As mentioned, we are utilising vCAC 6.1 and VRM.Datacenter.Location cannot be specified in the Property Dictionary.
I have seen this worked in vCAC 6.0 and it may have returned in vCAC 6.2? According to > http://vcdx56.com/2014/12/04/heads-up-vcloud-automation-center-property-definition-information/
I am also unable to use Reservation Policy __ReservationID as I have two reservations for each Reservation Policy.
Selecting a Reservation policy would not define a specific Cluster. If I have a specific Reservation Policy for each Reservation then a user would have to select between two UID's for the reservations that wouldn't make sense to them.
It seems like my only option is to upgrade to 6.2 or create a vCO workflow that assigns a Storage Policy and DRS group depending on the location the system ends up in.
Thanks for the input!
Dave

How can I avoid the Local storage pop-up question dialog box during playing you tube vedios ?

How can I avoid the Local storage pop-up question dialog box during playing you tube vedios ?

You might try tweaking your global privacy settings. I suspect it's set to "always ask."
Go to this page -- http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager02.htm l -- which contains the settings panel for Flash Player, and click on the various "deny" buttons to disable this. (It's a good idea to click on all the tabs to check the settings.)
If this works for you, please post back. (I know it worked for me.)
Ortho_Fan
(not a techie)

JMSClientExceptions:055053 -WebLogic10 Cluster - Remote WebLogic JMS - Help

All,
We are using a foreign JMS provider from WeLogic 10 cluster to connect to the Remote WebLogic JMS Server. We are getting below error while posting the data to the queue. Any help , ideas as to why this is occuring please?
/ Error
Error during connection/session creation:weblogic.jms.common.JMSException: [*JMSClientExceptions:055053*]Error creating connection to the server: java.rmi.UnmarshalException: failed to unmarshal class weblogic.jms.client.JMSConnection; nested exception is: java.io.StreamCorruptedException|portal
Thanks a lot for your help.

All
The issue popped up gain. Below is the full stack trace. I confirmed that we are using the t3 URL to connect to remote JMS server (which is Weblogic 10 /JMS). Appreciate any insights help to resolve this issue.
// Stack Trace
weblogic.jms.common.JMSException: [JMSClientExceptions:055053]Error creating connection to the server: java.rmi.UnmarshalException:
failed to unmarshal class weblogic.jms.client.JMSConnection; nested exception is:
java.io.StreamCorruptedException
at weblogic.jms.client.JMSConnectionFactory.setupJMSConnection(JMSConnectionFactory.java:253)
at weblogic.jms.client.JMSConnectionFactory.createConnectionInternal(JMSConnectionFactory.java:285)
at weblogic.jms.client.JMSConnectionFactory.createQueueConnection(JMSConnectionFactory.java:165)
at com.juniper.core.mdb.MessageSender.initSession(MessageSender.java:79)
at com.juniper.core.mdb.MessageSender.<init>(MessageSender.java:64)
at com.juniper.core.mdb.MDBHelper.processMessage(MDBHelper.java:98)
at com.juniper.core.mdb.BaseMDB.onMessage(BaseMDB.java:35)
at weblogic.ejb.container.internal.MDListener.execute(MDListener.java:466)
at weblogic.ejb.container.internal.MDListener.transactionalOnMessage(MDListener.java:371)
at weblogic.ejb.container.internal.MDListener.onMessage(MDListener.java:327)
at weblogic.jms.client.JMSSession.onMessage(JMSSession.java:4072)
at weblogic.jms.client.JMSSession.execute(JMSSession.java:3964)
at weblogic.jms.client.JMSSession$UseForRunnable.run(JMSSession.java:4490)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:464)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:200)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:172)
Caused by: java.rmi.UnmarshalException: failed to unmarshal class weblogic.jms.client.JMSConnection; nested exception is:
java.io.StreamCorruptedException
at weblogic.rjvm.ResponseImpl.unmarshalReturn(ResponseImpl.java:229)
at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:338)
at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:252)
at weblogic.jms.frontend.FEConnectionFactoryImpl_1001_WLStub.connectionCreate(Unknown Source)
at weblogic.jms.client.JMSConnectionFactory.setupJMSConnection(JMSConnectionFactory.java:244)
... 15 more
Caused by: java.io.StreamCorruptedException
at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1332)
at java.io.ObjectInputStream.readObject(ObjectInputStream.java:348)
at weblogic.utils.io.ChunkedObjectInputStream.readObject(ChunkedObjectInputStream.java:195)
at weblogic.rjvm.MsgAbbrevInputStream.readObject(MsgAbbrevInputStream.java:565)
at weblogic.utils.io.ChunkedObjectInputStream.readObject(ChunkedObjectInputStream.java:191)
at weblogic.rmi.internal.ObjectIO.readObject(ObjectIO.java:62)
at weblogic.rjvm.ResponseImpl.unmarshalReturn(ResponseImpl.java:227)
... 19 more
Thanks
Edited by: user3285437 on May 4, 2009 9:26 AM

Storage Location from USERTEMP1 not picked during Goods Issue

Hi All,
We had populated the USERTEMP field in FMDERIVE with the Storage Location using the steps mentioned in the following thread
Fund Center not getting populated through FMDERIVE
The problem is that during a Goods Issue made from MIGO, this particular field is not getting picked up in the USERTEMP (trace was set up in FMDERIVE, which showed that the USERTEMP is empty).
But in the case of PR/PO and other purchases, the USERTEMP is getting derived properly with the storage location.
Why is that the USERTEMP behaves differently for a Goods Purchase and a Goods Issue ?
Requesting help from the experts on this issue,
Thanks,
Wy.

Hi Eli,
We replicated the development we did for procurement (copying from storage location into USERTEMP) by finding out the enhancement point and the code worked fine here.
One important thing to note is that the buffer need to be cleared everytime, before a value is entered here - the USERTEMP field is static otherwise.
Thanks for your inputs,
Wy

Storage Spaces: Virtual Disk taken offline during file copy, marked as "This disk is offline because it is out of capacity", but plenty of free space

Server 2012 RC. I'm using Storage Spaces, with two virtual disks across 23 underlying physical disks.
* First virtual disk is fixed provisioning, parity across 23 physical disks: 10,024GB capacity
* Second virtual disk is fixed provisioning, parity across the remaining space on 6 of the same physical disks: 652GB capacity
These have been configured as dynamic disks, with an NTFS volume spanned across the two (larger virtual disk first). Total volume size 10,676GB. For more details of the hardware, and why the configuration is like this, see: http://social.technet.microsoft.com/Forums/en-US/winserver8gen/thread/c35ff156-01a8-456a-9190-04c7bcfc048e
I'm copying several TB from a network share to this volume. It is very slow at ~12MB/sec, but works. However, three times so far, several hours in to the file copy and with plenty of free space remaining, the 10,024GB virtual disk is suddenly taken offline.
This obviously then fails the spanned volume and stops the file copy.
The second time, I took screenshots, below. The disk (Disk27) is marked offline due to "This disk is offline because it is out of capacity". And the disk in the spanned volume is marked as missing (which is what you would expect when one of its member disks
is offline).
I can then mark the disk (Disk27) back online again, and this restores the spanned volume. I can then re-start the file copy from where it failed. There doesn't appear to be any data loss, but it does cause an outage that requires manual attention. As you
can see, there is plenty of space left on the spanned volume.
Each time this has happened, there are a few event 150 errors in the System event log: "Disk 27 has reached a logical block provisioning permanent resource exhaustion condition.". Source: Disk.
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="disk" />
<EventID Qualifiers="49156">150</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2012-06-07T11:24:53.572101500Z" />
<EventRecordID>14476</EventRecordID>
<Channel>System</Channel>
<Computer>Trounce-Server2.trounce.corp</Computer>
<Security />
</System>
- <EventData>
<Data>\Device\Harddisk27\DR27</Data>
<Data>27</Data>
<Binary>000000000200300000000000960004C0000000000000000000000000000000000000000000000000</Binary>
</EventData>
</Event>
This error seems to be related to thin provisioning of disks. I found this:
http://msdn.microsoft.com/en-us/library/windows/desktop/hh848068(v=vs.85).aspx. But both these Virtual Disks are configured as Fixed, not Thin provisioning, so it shouldn't apply.
My thoughts: the virtual disk should not spuriously go offline during a file copy, even if it was out of space. And in any case, there is plenty of free space remaining. Also, I don't understand the reason for why it is marked as offline ("This disk is offline
because it is out of capacity"). Why would a disk go offline because it was out of thin capacity, rather than just returning an "out of disk space" error while keeping it online.

Interesting Thread, I've been having the same issue. I had a failed hardware RAID that was impossible to recover in place, so after being forced to do a 1:1 backup, I find myself with 5 2TB hard drives to play with. Storage Spaces seemed like an interesting
way to go until I started facing the issues we share.
So my configuration is A VM Running Windows Server 2012 RC with 5 Virtualized Physical drives using a SCSI interface, 2TB in size that make up my storage pool. A Single Thinly provisioned Disk of 18 TB (using 1 disk for parity)
Interestly enough, write speed has not been an issue on this machine (30~70MB/s, up from 256k on the beta)
Of note to me is this error in my event log 13 minutes before the drive disappeared:
"The shadow copies of volume E: were deleted because the shadow copy storage could not grow in time.Consider reducing the IO load on the system or choose a shadow copy storage volume that is not being shadow copied."Source: volsnap, Event ID: 25, Level: Error
followed by:
"The system failed to flush data to the transaction log. Corruption may occur in VolumeId: E:, DeviceName: \Device\HarddiskVolume17.(The physical resources of this disk have been exhausted.)"Source: Ntfs (Microsoft-Windows-Ntfs), Event ID: 140, Level: Warning
I figure the amount of space available to me before I start encountering physical limits is in the vicinity of about 7TB. It dropped out for the second time at 184 GB.
FYI, the number of columns created for me is 5
Regards,
Steven Blom

Infinite loop during recovery of JE 4.1.10 database environment

Hi there,
We have a JE 4.1.10 database environment which is over 20GB in size. In order to improve performance we increased je.log.fileCacheSize so that we could cache all of the 10MB DB log file descriptors in memory and prevent JE from having to constantly open/close log files (the environment is only partially cached in memory and there are more than 2000 log files). Unfortunately, we failed to increase the file descriptor ulimit from the Linux default of 1024 and our application failed when the ulimit was reached.
Since then we've reverted the settings and increased the JVM heap size so that we can fully cache everything in memory again. However, we are having problems recovering the DB environment. It looks like the environment recovery proceeds through the 10 recovery steps but gets stuck while loading the log file utilization meta-data:
Stack trace #1:
"main" prio=10 tid=0x000000005622f000 nid=0x5d94 runnable [0x00000000419fe000]
java.lang.Thread.State: RUNNABLE
     at java.io.RandomAccessFile.seek(Native Method)
     at com.sleepycat.je.log.FileManager.readFromFileInternal(FileManager.java:1605)
     - locked <0x00002aaaf80dca88> (a com.sleepycat.je.log.FileManager$1)
     at com.sleepycat.je.log.FileManager.readFromFile(FileManager.java:1560)
     at com.sleepycat.je.log.FileManager.readFromFile(FileManager.java:1498)
     at com.sleepycat.je.log.FileSource.getBytes(FileSource.java:56)
     at com.sleepycat.je.log.LogManager.getLogEntryFromLogSource(LogManager.java:861)
     at com.sleepycat.je.log.LogManager.getLogEntry(LogManager.java:790)
     at com.sleepycat.je.log.LogManager.getLogEntryAllowInvisibleAtRecovery(LogManager.java:751)
     at com.sleepycat.je.tree.IN.fetchTarget(IN.java:1320)
     at com.sleepycat.je.tree.BIN.fetchTarget(BIN.java:1367)
     at com.sleepycat.je.dbi.CursorImpl.fetchCurrent(CursorImpl.java:2499)
     at com.sleepycat.je.dbi.CursorImpl.getCurrentAlreadyLatched(CursorImpl.java:1545)
     at com.sleepycat.je.dbi.CursorImpl.getNextWithKeyChangeStatus(CursorImpl.java:1692)
     at com.sleepycat.je.dbi.CursorImpl.getNext(CursorImpl.java:1617)
     at com.sleepycat.je.cleaner.UtilizationProfile.getFirstFSLN(UtilizationProfile.java:1262)
     at com.sleepycat.je.cleaner.UtilizationProfile.populateCache(UtilizationProfile.java:1200)
     at com.sleepycat.je.recovery.RecoveryManager.recover(RecoveryManager.java:221)
     at com.sleepycat.je.dbi.EnvironmentImpl.finishInit(EnvironmentImpl.java:549)
     - locked <0x00002aaaf8009868> (a com.sleepycat.je.dbi.EnvironmentImpl)
     at com.sleepycat.je.dbi.DbEnvPool.getEnvironment(DbEnvPool.java:237)
     at com.sleepycat.je.Environment.makeEnvironmentImpl(Environment.java:229)
     at com.sleepycat.je.Environment.<init>(Environment.java:211)
     at com.sleepycat.je.Environment.<init>(Environment.java:165)
Stack trace #2:
"main" prio=10 tid=0x000000005622f000 nid=0x5d94 runnable [0x00000000419fe000]
java.lang.Thread.State: RUNNABLE
     at com.sleepycat.je.tree.IN.findEntry(IN.java:2086)
     at com.sleepycat.je.dbi.CursorImpl.searchAndPosition(CursorImpl.java:2194)
     at com.sleepycat.je.cleaner.UtilizationProfile.getFirstFSLN(UtilizationProfile.java:1242)
     at com.sleepycat.je.cleaner.UtilizationProfile.populateCache(UtilizationProfile.java:1200)
     at com.sleepycat.je.recovery.RecoveryManager.recover(RecoveryManager.java:221)
     at com.sleepycat.je.dbi.EnvironmentImpl.finishInit(EnvironmentImpl.java:549)
     - locked <0x00002aaaf8009868> (a com.sleepycat.je.dbi.EnvironmentImpl)
     at com.sleepycat.je.dbi.DbEnvPool.getEnvironment(DbEnvPool.java:237)
     at com.sleepycat.je.Environment.makeEnvironmentImpl(Environment.java:229)
     at com.sleepycat.je.Environment.<init>(Environment.java:211)
     at com.sleepycat.je.Environment.<init>(Environment.java:165)
It looks like it is spinning in UtilizationProfile.getFirstFSLN(). Examining the syscalls using strace shows that JE is looping around the same 3 log files over and over again (note the lseek calls on fd 147):
14719 lseek(147, 2284064, SEEK_SET) = 2284064
14719 read(147, "\310\f9\311\v\0\330\331\"\0:\0\0\0\2{\231\302\36\27\0\340\24\0\0\33\201\230\0\340\24\0"..., 4096) = 4096
14719 lseek(95, 3030708, SEEK_SET) = 3030708
14719 read(95, "B\17\36\373\v\0\350<.\0B\0\0\0\2{3\323\36\27\0+\21\0\0\210\221\230\0+\21\0"..., 4096) = 2469
14719 lseek(95, 3025672, SEEK_SET) = 3025672
14719 read(95, "#(\2571\v\0b*.\0\202\0\0\0\2{\26\323\36\27\0\0160\0\0f\221\230\0Z\22\0"..., 4096) = 4096
14719 lseek(74, 35084, SEEK_SET) = 35084
14719 read(74, "\361\34s\272\v\0\300\210\0\0h\0\0\0\2{\240\323\36\27\0\346\36\0\0\215\225\230\0\350\22\0"..., 4096) = 4096
14719 lseek(74, 90663, SEEK_SET) = 90663
14719 read(74, "\2\16P\341\v\0#;\1\0B\0\0\0\2{\275\323\36\27\0\366/\0\0003H.\0$\3\0"..., 4096) = 4096
14719 lseek(147, 2284064, SEEK_SET) = 2284064
14719 read(147, "\310\f9\311\v\0\330\331\"\0:\0\0\0\2{\231\302\36\27\0\340\24\0\0\33\201\230\0\340\24\0"..., 4096) = 4096
14719 lseek(95, 3030708, SEEK_SET) = 3030708
14719 read(95, "B\17\36\373\v\0\350<.\0B\0\0\0\2{3\323\36\27\0+\21\0\0\210\221\230\0+\21\0"..., 4096) = 2469
From the output of lsof we can determine the names of the log files associated with the above file descriptors, but I'm not sure if this is useful or not. We also ran DbVerifyLog against the entire DB log and it produced no results, so this indicates to me that the DB is not corrupt after all (although it could be that DbVerifyLog simply does not check the utilization profile meta data).
I had a look at the change log for 4.1.17 but couldn't see any relevant bugs. It's probably worth noting that this DB does not use HA, duplicates, or secondary indexes.
So I guess I have two questions:
1) Is this a bug? Presumably the DB should recover even in the event of a human error induced failure like this?
2) Can we recover the DB somehow, e.g. using DbDump/DbLoad?
Let me know if you need any additional information.
Cheers,
Matt

1) Is this a bug? Presumably the DB should recover even in the event of a human error induced failure like this?It is probably a bug, but it depends on exactly what happened during the original crash.
2) Can we recover the DB somehow, e.g. using DbDump/DbLoad?If you can't open the environment, only DbDump -R (salvage mode) can be used, which requires identifying the active data by hand. Not a good option.
Let me know if you need any additional information.Do you happen to have the original stack trace, where you ran out of FDs?
How long did the looping go on before you killed the process?
--mark

Getting "Serialized xml is nested too deeply" when trying to restart AppFabric Cache Cluster remotely with Powershell

Hi! I´m Getting the following error when trying to restart the AppFabric Cache Cluster:
PS C:\temp> .\restartappfabric.ps1
Serialized xml is nested too deeply.
+ CategoryInfo : OperationStopped: (ServerName:String) [], PSRemotingTransportException
+ FullyQualifiedErrorId : JobFailure
+ PSComputerName :
ServerName
Here's The Script:
$ServerName="ServerName"
$sc = {
Import-module DistributedCacheAdministration
Use-CacheCluster
Restart-CacheCluster
Invoke-Command -computername $ServerName -scriptblock $sc
Powershell remoting is fully enabled and working fine con remote computers. When testing the script against a TEST computer is working fine, but when executing the script against PRE & PROD servers I get the error described above.
Running the lines within the scriptblock locally in the servers works fine.
Any help on this would be appreciated.
Thanks

Thanks man for your help. Tried using the connectionstring but got the same results
PS C:\temp> Invoke-Command -ComputerName Servername {import-Module DistributedCacheAdministration;Use-CacheCluster -P
rovider XML -ConnectionString "\\vmbcorp.com\FS\ApplicationContent\PRE\AppFabricCache" ;Restart-CacheCluster}
Serialized xml is nested too deeply.
+ CategoryInfo : OperationStopped: (BBLAMTPDAFC01:String) [], PSRemotingTransportException
+ FullyQualifiedErrorId : JobFailure
+ PSComputerName : BBLAMTPDAFC01
PS C:\temp>
Running the commands locally with the ConnectionString swith works as well. Running out of Ideas.. May be using psexec..

Azure File Storage error The remote name could not be resolved

I am following http://azure.microsoft.com/en-us/documentation/articles/storage-dotnet-how-to-use-files/
While executing $s = New-AzureStorageShare mysampleshare -Context $ctx I get error as
New-AzureStorageShare : The remote name could not be resolved: 'mystorageaccount.file.core.windows.net'
At line:1 char:6
+ $s = New-AzureStorageShare elasticsearch -Context $ctx
+      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : CloseError: (:) [New-AzureStorageShare], StorageException
    + FullyQualifiedErrorId : StorageException,Microsoft.WindowsAzure.Commands.Storage.File.Cmdlet.NewAzureStorageShare
Thanks,
Subodh

Azure Files is a Preview feature. Did you request and got access to it at the billing portal's Preview Features (https://account.windowsazure.com/PreviewFeatures)?
Also, you can now try creating the File share via the Preview Portal (https://portal.azure.com -> your storage account -> "File Shares").

PowerShell Get-Cluster Remote API Error

I am running a powershell script to get cluster information. The script works perfectly sometimes but sometimes fails on the get-cluster -domain command. It will fail and then maybe a half hour later it will work. Here is the exact
error:
Message: Could not retrieve the list of clusters on the network. A remote API error occurred.
ErrorCode: -2147022769
Any ideas on how to track down exactly what the problem is and correct it?

The similar problem here:
https://social.technet.microsoft.com/Forums/windowsserver/en-US/9626fa01-968f-4793-b2ee-b2f7e8bf1517/powershell-getcluster-a-remote-api-error-occurred?forum=winserverClustering
You may try use -Name switch instead of domain, but its a workaround, not a solution. I would recommend installing network monitor to proper cluster servers if you see something that may catch your eyes.
Please remember to "Mark as answer" if it helps. Thank You.

SMB File Share Storage Failover Cluster "path is not valid folder path"

I am having an issue that I am scratching my head over. So I have setup a 3 node Hyper-V host cluster that I am attempting to use SMB File Share storage for the shared storage medium. I have been trying to migrate a virtual machine from one of the nodes
local storage into the file share using System Center VMM 2012 R2 with UR5 however I keep getting the message "The specified path is not a valid folder path on node2.domain.com" for the storage that VMM automatically selects for placement of files
from the migration. However what is odd is to the same file share for storage I can do a new deployment of a virtual machine to the same cluster with the same shares; I can also delete a virtual machine from the share fine; the file share for the virtual machine
I library I am deploying machines from is the same server as the file shares for the cluster that I am deploying to so maybe that is why that succeeds; if I try to move the recently deployed VM from one file share to another for storage same error comes up.
The three nodes all reference the same file server, which is just one file server for the storage, and the shares were created in VMM and as such the file share permissions were setup by VMM so they should be sufficient. I have also attempted this with both
delegation of CIFS and without through AD (trust to specified computers with CIFS, Hyper-V Replica and Microsoft Virtual Console Service via Kerberos only).
I am stumped as to what to check next or how to get this working and would appreciate any guidance anyone can give towards a resolution for this problem.

Jeff,
Thanks for reporting this.
There's an known issue with UR5 that VMM gives wrong error when deploying a HAVM onto a SMB share. In that situation, VMM complains "Invalid folder path".
To confirm you are hitting the same issue, would you kindly let me know:
1. Are you trying to migrate a HighlyAvailable VM onto the SMB share?
2. On UI of "Migrate Storage Wizard", if you click "Browse", do you see the target file share showing up in "Select Destination Folder" dialog?
3. By "the three nodes all reference the same file server", I assume you added the target file share onto the list of File Share Storage thru the cluster's properties UI. If so, please go to the UI and check whether the access status shows
green there.
4. By "local storage", do you mean "local disk"? Or a shared LUN from any array? I assume it's not "available storage" or "CSV" of the cluster. Please double confirm.
Note: If we are sure hitting the known issue, I will later re-direct you to a hotfix. But let's make sure it is the issue first.
Look forward to your reply.

JMS Cluster Remote Access

When connecting to a JMS resource externally, in order to get the correct context, you need to connect to the specific host:port of the server you are looking send/receive messages to/from. How can I do this when I want to cluster the JMS resources, but access them remotely? I don't want to expose the host:port Managed Servers in the cluster.

When connecting to a JMS resource externally, in order to get the correct context, you need to connect to the specific host:port of the server you are looking send/receive messages to/from. How can I do this when I want to cluster the JMS resources, but access them remotely? I don't want to expose the host:port Managed Servers in the cluster.

Storage 7310:Cluster Remote Appliance loops during rejoin

Similar Messages

Maybe you are looking for