Storage messages not ready yett

i can not get my messages up on my mobile it just says message storage not ready yet, can i fix it thu my lapyop if i plug my mobile to it and if so how do it do it thanks

Hi,
I think that happens mostly in Nokia phones..You can try by connecting your phone to the computer and then installing Nokia PC Suite. From PC suite try to delete the unwanted messsages..
That is just one of the solution..Here is a link from Nokia that will give you few more tips..
message storage not ready yet
Note:
If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
Although I am an HP employee, I am speaking for myself and not for HP.
**Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

Similar Messages

  • C220M3 LSI Storaged Raid Subsystem not ready yet 9271-8i

    New C220M3 with 9271-8i out of box with 2.0.1b firmware
    Control H doesn't boot into WebBios, instead I get EFI Shell with map:cannot find required map name.
    Press ESC in 1 seconds to skip startup.nsh, any other key to continue
    From the CIMC I select 2 drives to create a drive group and it fails with message;
    Error: Storage Raid subsystem not ready yet
    See screenshot;

    Make sure the optionROM for the raid controller is enable in the bios. 
    1)Reboot server
    2)Press F2 when you see the option to go into bios
    3)go to advance 
    4)select the last option here I believe it is LOM and PCIe
    5) verify that in slot 2 the optionROM is loaded

  • I TRIED TO ACTUALIZE MY SOFTWARE, BUT THE RESTORE SYSTEM HAS MORE THAN 36 HOURS AND IT IS NOT READY YET.... IT SEEMS STOPPED. BUT IA CANNOT RETRY, 'CAUSE IT WILL BEGIN AGAIN FRO THE START..... WHAT CAN I DO TO RESTORE CORRECTLY?

    my ipad 2, is not restoring from the last setup.... it is taking more than 36 hours and is not ready, is not finished yet....it seems like stopped... But it is not getting any progress. What I must do to restore and start up again?
    Thanks
    ALEXCG

    If the restore has stopped on the iPad then try putting it into recovery mode : http://support.apple.com/kb/ht4097

  • "Message storage memory not ready" error message

    Ever since I got my Nokia 2320 (which for some unknown reason is not listed on this site) back in December, it ran slow when I turned it on and took a few minutes (up to five) to what I call "recall the messages and remember it could send messages."  But lately the time it takes to recall the messaging is longer and longer.  A couple days ago it took me 27 hours.  This time, its been 30.  I read on another site about a guy who had this same message on this same phone and it had been 3 days and the problem had still not corrected itself.  I want to know what is happening, why, and how to fix it.  I called my carrier customer service and have been on the phone with them on and off for about a month about it.  They have NO CLUE what it is.  HELP!

    Clean out the messages and reset the 2320. Dial *#7780# 12345 restore factory settings, keep data.
    http://www.forum.nokia.com/devices/2320_classic/
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • SolMan ChaRM - System landscape not ready yet

    Hi all,
    We are configuring ChaRM for an implementation use, therefore all the systems are not set up yet.
    Is it possible in SolMan to define logical component without "real" systems ?
    We saw that in STMS it was possible to create virtual systems, but how do we link these virtual systems to SolMan ChaRM ?
    Is it possible to define a virtual system landscape and to build and configure ChaRM scenario with this ?
    Thanks a lot for all your help,
    Regards.

    Yes, it is possible to define a development system and virtual systems (Q- and P-System).
    Via transaction SMSY you can describe the planned Q- and P-System at first as 'virtual'.
    Create transport routes with transport buffers as you would do for existing systems.
    Define the buffers as they should be named in future.
    For experimental purposes we connected our IDES-System to our development SolMan system.
    In this environment we could map such a ChaRM-configuration.
    In the meantime we practiced it in our production SolMan system, too.
    Best regards
    Horst

  • Epson scanning very slow - Universal binaries not ready yet...

    I just bought a iMac Dual Core to replace my G4 iMac 1.25Ghz. Both have 2gb of RAM. I am scanning my own art work to place on the web and to send by email.
    It turns out that scanning with my Epson scanner is not a bit faster. I just replaced the scanner in January with the latest model.
    After contacting Epson support, it turns out that no universal binary drivers are available and the current version is extremely slow...
    I just want to say that I find this extremely disappointing, there are a so many Epson scanners out there, and than this....
    And Epson can't / doesn't want to say when this will be fixed...
    Thank you for contacting the Epson Connection.
    We are currently testing new drivers for the Intel Duo Core System Macs.
    Once the testing is complete, new drivers will be posted on the applicable Epson Support web-sites. Due to the complexity of this process, we cannot promise an exact date for availability. Please check the Epson Support web-sites for any new driver postings at support.epson.com.
    iMac Dual Core Intel Mac OS X (10.4.5) 2gb memory

    I found Universal Binaries for my Epson Multifunction CX6600
    so check out frequently ...
    Thierry

  • ***Not Retrieved Yet***

    Every time I receive a picture text, I get the message ***Not Retrieved Yet***. Of course the picture never does retrieve. I have had this phone for a little over a year and it just now started doing this. Any suggestions on why this is happening and what I can do to fix it?

    Try the following Help Documents:
    KB15700-Unable to receive MMS messages on the BlackBerry smartphone
    Best of luck,
    --Phil
    Phil
    Specialist, Emergency Medical & Disaster Response
    Blackberry Playbook 64GB, 9900, 9810, 9800, 9780, 9700, 9000, 8310, 8220, 8700R, 8100, 8300, 7290
    1. Please thank those who help you by clicking the Like button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post Accept as Solution, which solved it for you!

  • No system manager locations set, search application might not be ready yet

    Hi,
    I am just setting up a new SharePoint 2013 environment (Windows server 2008 R2 + SQL Server 2008 R2) and I am getting this error message in powershell when I try to save my new search topology: No system manager locations set, search application might
    not be ready yet. The installation script used to install and create the search service originates from this link: http://www.toddklindt.com/blog/Lists/Posts/Post.aspx?ID=378 and I receive the error message after running $clone.Activate().
    ULS is writing this:
    05-29-2013 14:57:00.94 mssearch.exe (0x19C0) 0x1A68 SharePoint Server Search Crawler:Content Plugin cd11 Critical Content Plugin can not be initialized - list of CSS addresses is not set.
    05-29-2013 14:56:08.27 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration dkd5 High synchronizing search service instance 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:08.27 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration eff0 High synchronizing search data access service instance 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.38 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ajzc7 Medium Cleanup of Orphan Systems in server SR00667 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration agwve Medium Synchronizing legacy admin 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ai4f1 High Unable to get systemmanagerlocation from db 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ai84s Medium Skipping legacy admin sync as there is no system manager location set 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration agwvc Medium Skipping Topology Synchronize.The active topology does not have any Components. 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    05-29-2013 14:56:09.46 OWSTIMER.EXE (0x09B0) 0x1304 SharePoint Server Search Administration ajnco Medium Cleaning up Orphan nodes in system : 7B4831 8f28209c-5d35-a0cc-7fad-bd7b088335ee
    So basically all else is going fine before saving the clone. Application pool is created, search service and it´s proxy is created (the databases are also created in SQL). The clone is after this created and then the components are added.
    I have tested with both March and April CU. I use separate accouns for search service, installation and so on. I have tested giving the search application pool account local admin right but didnt make any difference.
    Some posts in Internet around this matter is pointing towards there might be 4 missing patches like here: http://blog.steigis.ch/sharepoint/sps2013/search-in-starting-state/  They are all installed on my server.
    Search host controller service and SharePoint Server Search are started.
    Before creating the service I ran this. I have done this on all my other installations of search to solve the problem with the host service is in "starting" state. Info taken from here: http://mmman.itgroove.net/2012/12/search-host-controller-service-in-starting-state-sharepoint-2013-8/
    $acl = Get-Acl HKLM:\System\CurrentControlSet\Control\ComputerName
    $person = [System.Security.Principal.NTAccount] "Users"
    $access = [System.Security.AccessControl.RegistryRights]::FullControl
    $inheritance = [System.Security.AccessControl.InheritanceFlags] "ContainerInherit, ObjectInherit"
    $propagation = [System.Security.AccessControl.PropagationFlags]::None
    $type = [System.Security.AccessControl.AccessControlType]::Allow
    $rule = New-Object System.Security.AccessControl.RegistryAccessRule($person, $access, $inheritance, $propagation, $type)
    $acl.AddAccessRule($rule)
    Set-Acl HKLM:\System\CurrentControlSet\Control\ComputerName $acl
    $sh = Get-SPServiceInstance | ? {$_.TypeName -eq "Search Host Controller Service"}
    After this I do a server restart and continue with creating the search service and its components.
    Any ideas?

    I had exactly the same issue when setting up a new SharePoint 2013 environment (Windows Server 2012, SP2013 with PU March 2013 and CU April 2013, .NET 4.5). I have tried almost everything during the last weeks to configure the Search Service Applicatione,
    e.g. create the service from GUI, create it from PowerShell, verify my search account had enough permissions, check for missing updates etc. etc. Same error no matter what I tried.
    Using another SharePoint farm I went through a similar configuration of the Search Service Application. I used exactly the same script as I did on the first server and the setup completed without any issues. So why did the same features fail during the setup?
    To find an answer I compared the two farms and the only thing I noticed that were different was the lack of .NET 3.5 on the application and WFE server in the first farm. I then enabled .NET 3.5 features and now the Search Service Application works as expected
    I had no idea enabling .NET 3.5 features would solve the issue - I thought .NET 4.5 was backward compatible and SharePoint only requires .NET 4.5 according the
    requirements?

  • Error message: User data is not indexed, yet. Index user data first

    Greeting All,
    Each time I try to index a 'Prepared' searchObjectConnector in the cockpit.. I get a message <
    User data is not indexed, yet. Index user data first>. even that I ran the z_ESH_AU_UPLOAD_AUTH_RFC_720 report in R/3 system.. and checked the auth /user data in the admin cockpit.. and it was indexed..
    1.any idea why I keep getting this error
    2.any idea how can I clean the buffer or the message Queu.. my guess this might  be not error but a q message..
    3. any suggestion please
    Thanks

    Hi Areege,
      I noticed that you created an OSS message on this issue. That was a good idea.
    There is an answer for you in OSS from yesterday.
    Kind regards, Klaus

  • My Ipad displays a message: Not Enough Storage: This ipad cannot be backed up because there is not enough icloud storage available. You can manage  your storage in settings.... Ive tried closing and settings but it doesn´t work and cant do anything

    My Ipad 3erd Gen... si dsiplayin a message:
    "Not Enough Storage: this ipad cannot be backed up because there is noit enough iCloud storage available. you can manage yor setorage in settings"
    Ihave tride pushing either Close or Settings and it doesnt do anything, i cant shut down or push a command in setteings mode, the message appears to be frozen in the center of the screen!
    HELP!!!!!

    Try a reset:
    Hold the Sleep and Home button down for about 10 second until you see the Apple logo.

  • Why do I keep getting a not enough storage message when trying to install GarageBand on my iPhone 4

    I have been trying to re-install GarageBand on my iPhone 4. I have tried downloading from iTunes app store and installing by sync from my MacBook. Neither will work. I keep getting the same "not enough storage" message.

    You may need as much as 2Gb free, at least on a temporary basis while installing the app.
    tt2

  • There's a not enough storage message appearing and I can't get rid of it.

    There's a not enough storage message appearing and I can't get rid of it.

    A reset may help: Tap and hold the Home button and the On/Off button at the same time for approximately 10-15 seconds, until the Apple logo reappears. When the logo appears, release both buttons and await restart.

  • I can not take pictures or back up my phone due to error message not enough storage.I have all of my data turned off and still can not back phone up.? I have deleted lot of pics and messages and still get message..

    I can not take pictures or even back my phone up due to error message not enough storage I have went into manage storage and turned all my apps to off and I still get error. I also have deleted a ton of pictures and apps.

    Hi there mistib,
    You may find the information in the article below helpful.
    iOS: "Not enough free space" alert when trying to sync
    http://support.apple.com/kb/ts1503
    -Griff W.

  • Firefox is trying to update my 8.0 version to 9.0.1. I'm not ready to do so because the Norton Toolbar is not yet compatable with the new Firefox release. How do I get firefox to stop trying to update every time I open the application?

    Question
    Firefox is trying to update my 8.0 version to 9.0.1. I'm not ready to do so because the Norton Toolbar is not yet compatable with the new Firefox release. How do I get firefox to stop trying to update every time I open the application?

    Swarnava wrote: '''''Firefox 9 is Compatible with Norton 2011, 2012, 360 v5'''''.
    This reads backwards, It is the other way as "Norton update is compatible with Firefox 9".

  • Photoshop cs4 bridge,getting not enough storage message.

    I have a computer that the motherboard died a couple of weeks ago. The motherboard and processor have been replaced as well as upgrading the ram from 4 gb to 12. We were able to use the old hard drive with no problems, maybe, just booted it up yesterday and am still working things out. Photoshop cs4 was installed on the computer and it seems to be working fine, except that I'm getting "not enough storage" messages when I try to do things I was able to do before the colapse. One thing I've noticed is that in the 32 bit version of Photoshop preferences it shows around 3 gb of ram available while the 64 bit version shows the full 12gb. Is this typical? and if not why would it be showing up this way?  I'm not sure that has anything to do with the problems with bridge it is a stand alone program now. Anyway, does anyone have any idea what could be the problem with this? Would uninstalling and re-installing the programs help?
    Windows 7 Home Premium  64 bit system
    12 GB RAM
    I'm not sure what else would be needed about the computer, let me know if there is anything else.
    Thanks for any help,
    Linda

    Is the "not enough storage" error message showing up in Bridge or Photoshop? I ask that because it seems to be a Bridge error message and the Bridge forum could better handle that.
    If Photoshop is giving you this message, check your Preferences > Performance and see that the ram allocated is not more than 65-70% of total and look at your scratch disk allocation in that section as well.
    I would also consider resetting Photoshop's preferences. Sometimes that clears up problems, and of course be sure you install the latest CS4 updates.
    I'm assuming you have to use 32 bit Photoshop CS4 (example32 bit third party plugins).  If not use 64 bit CS4 and see if that works.
    I'd heed the upgrade advice as well. After December, CS4 to CS6 upgrade price will increase from $200 to $700.

Maybe you are looking for