Storedge 3310, new drives, and an error

I've just installed 5 new Sun 146GB 10K drives in my SE3310. The install and LUN setup went fine, format went fine, but I'm getting this error on the console and in /var/adm with some frequency:
Sep 10 08:59:12 onestop scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@0,1 (sd74):
Sep 10 08:59:12 onestop incomplete read- retrying
Sep 10 09:11:28 onestop scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4/sd@0,0 (sd36):
Sep 10 09:11:28 onestop incomplete read- retrying
What's this telling me?
Thanks,
Harry
Message was edited by:
hboswell

Look at patch 113722-16 README.
RAID firmware 325Q addresses the following issues:
4826944 Copy and Replace function during rebuild causes data corruption
*4809793 scsi incomplete retry errors when cache is optimized for Random I/O*
4809787 After "defaults restore" fw asks for a controller unique id
4802207 SCSI Bus Reset and daemon.error under heavy load test for 3310
*4792748 3310 incomplete read- retrying w VTS*
4764506 Enabling secondary RS-232 port causes serial communication failure
may it be your case?

Similar Messages

Tried synching iphone for the first time on new PC and got error followed by itunes logo and USB cable picture. No idea what went wrong and now phone is in this screen locked. please help!

tried synching iphone for the first time on new PC and got error followed by itunes logo and USB cable picture. No idea what went wrong and now phone is in this screen locked. please help!

I tried connecting to iTunes and neither the PC nor iTunes recognizes the device. I went through all the troubleshooting on the Apple website for this issue and nothing worked. I've reinstalled iTunes, the driver, everything and still can't get either the PC or iTunes to recognize the phone. I don't know what else to do :-( any help or suggestions are highly appreciated!
I would hate to have lost all my info, especially contacts and calendar items since I have no idea what was backed up prior to the phone getting locked on this screen. I've been told that my only option is to go to the phone carrier and they will reset it for me, but that means it will wipe out all the info.
I hope someone has a fix other than that one.

I had iLife pre-installed on my aluminium Macbook 2009 with OSX Leopard on it. My hard drive broke but got most of the info off it and just installed snow Leopard on to a new drive and then downloaded and installed Mountain Lion over it. Now I don't have

I had iLife pre-installed on my aluminium Macbook 2009 with OSX Leopard on it. My hard drive broke but got most of the info off it and just installed snow Leopard on to a new drive and then downloaded and installed Mountain Lion over it. Now I don't have iLife anymore. How do I get it back?

Welcome to Apple Support Communities
Mac OS X doesn't come with iLife applications, so you have to install them manually after installing Mac OS X.
Insert the Applications disc or Mac OS X Install Disc 2 DVD and install iLfe applications. Then, open  > Software Update, and install the latest update. If you want, you can purchase iMovie, GarageBand and iPhoto in the App Store, so you will get the most recent version

I just set up my new iMac, and receive error messages when trying to purchase from the iTunes store (error 8003) or update from the App store (error 403 forbidden). THOUGHTS?

I just set up my new iMac, and receive error messages when trying to purchase from the iTunes store (error 8003) or update from the App store (error 403 forbidden). THOUGHTS?

I am not sure what you mean by "Flash Player for steam"; the only Flash Player installers I know is the ActiveX (for Internet Explorer) and the plugin (for other browsers); you can find both at http://helpx.adobe.com/content/help/en/flash-player/kb/installation-problems-flash-player- windows.html#main-pars_header
[topic moved to Flash Player forum]

I upgraded to OS X10.9.4 and now my Cannon scanner will not work. I downloaded the new driver and still no luck.

I upgraded to OS X10.9.4 and now my Cannon MX 860 scanner will not work. The printer works. I downloaded the new driver and still no luck. Please help!

Open Print & Scan preferences. Select the printer in the sidebar list and click on the Delete [-] button. CTRL- or RIGHT-click in the sidebar area and select Reset Print System from the context menu. Re-Add the printer by clicking on the Add [+] button, select your printer from the little browser that opens, select the proper driver if it isn't set automatically, then click on the Add button. See if it now works.
Oh, be sure you install the new driver you downloaded.
BTW, you don't have a PowerMac as shown in your profile. PowerMacs were tower machines that ran PPC processors, not Intel processors. You really should correct that information in your profile.

Geforce GTX 285, OS10.6.4, new driver, and performance

An experience: I was one of the unhappy users of a Geforce GTX 285, a GPU that just didn't want to perform according to specs. As an X-Plane pilot this fact gave me headaches and a low fps level. Now, shortly after installing the OS update to 10.6.4 I discovered a very recent new driver (19.5.8f03) for the card (http://www.nvidia.com/object/geforce-macosx-19.5.8f03-driver.html)
I installed it and also re-installed the latest CUDA version 3.0.14 (http://www.nvidia.com/object/MacOSX-CUDA-3.0.html). Since this update the GTX's performance is excellent on the Mac OS side of my PM.
I am no expert, but for power saving reasons the card seems to have three levels of clock speed that X-Plane was rarely able to trigger to the highest level. Perhaps the new driver lowers the load thresholds that trigger the card into higher performance?
Did anybody have a similar experience? Does anybody of you cognoscenti have an idea of what the driver changes may have been?

I've installed this new driver and it has not made the slightest difference to the performance of the MacPro running 10.6.4 with an EVGA 285 for Mac.
Half-Life2 frame rates are exactly the same post driver update as they were prior (much lower fps than when running 10.6.3).
What I have noticed is the fan noise ramps to an alarmingly high speed when entering various in-game environments. The fan was running so loud I quit the game in fear that some damage might be done to the card.
http://www.evga.com/forums/tm.aspx?m=428085

Installed new driver and printing still stops with images

I have a Cannon printer and have it shared thru the USB port on my Airport. Any time I have to print a large image file the print gets almost complete and just stops. Light keep blinking and the printer driver says it's still printing. No error messages. If I plug the printer back into the USB port on the Macbook it prints the image file just fine.
I was hopeful that this new driver would fix the problem. Anyone know of a solution?
Thanks,
Larry

Hi,
Different fonts will occupy different space to print.
So, the new font may occupy more space when compare to the old font and width of the window may not accomdate.
You can check by reducing the Font size of the new font, whether its actually printing with the new font.
Thanks & Regards,
Vamsi.

How do i move photos and catalog to a new drive and have lightroom make the same move

I am trying to move all my photos to a new drive with different drive letter. I know I can do a backup and restore inside PSE13 to perform that. However, I also have Lightroom 5 on the current setup. How would I now use the new location for the photos in lightroom if they are already moved by PSE?
Hope this makes sense!

I don't recommend the Time Machine or Migation Assistent approach. The first tneds to be very slow and the second often carries baggage that is probably best not transferred to a new computer.
Lightroom doesn't use activation, therefore, can be installed on your new Mac without having first removed it fom the old. Your images and catalogs can be copied across to the new Mac using an a portable disk drive as the transfer medium. Typically, on Mac computers, the catalog and image files are stored in the Pictures folder. If this is where you have them then then copy them to the same location on the new Mac. Once copied you can open the catalog folder then double click on the .lrcat file to launch Lightroom.

Hard drive and critical error messages

Hello, I have suddenly rec'd numerous hard drive errors "hard drive doesn't respond to system commands" and critical error messages "damaged hard drive clusters detected. private data is at risk." "system has detected a problem with one or more installed IDE/SATA hard disks" along with other error messages. I have a toshiba satellite A505 over a year old and never had a problem until now. Was just surfing the web on a retail site and started getting all these pop-ups. desktop is missing most icons, favorite list gone. not computer savvy when it somes to figuring the error messages out. Any help appreciated. Should I take it in somewhere to get fixed? Please help.
Thank You.

not computer savvy when it somes to figuring the error messages out. ... Should I take it in somewhere to get fixed?
Yes, Katy. Be sure to back up all your important files. The machine you get back will most likely have all of your pictures, Xmas cards, favorites, contacts and so forth missing.
Locate a Toshiba Service Center
-Jerry

Hard Drive Crash - need help with choosing new drive and installation

My hard drive seems to have crashed. My computer froze, and when I tried to reboot, it got stuck at the startup screen. I started from the system CD, ran the disk repair utility, and it said it could not repair the disk. I ran Tech Tool Pro and it could not repair the disk. I tried to start up in Target disk mode while connected to my older G4 iMac (that I'm using now as my backup), and the disk would not mount. So I need some expert advice - I am assuming the hard drive is toast. I wish I could at least mount it in target disk mode to transfer files, but I haven't been able to do that. I was going to take it in for repair (or possibly buy a new computer), but after reading some of the posts here, I am thinking I could just replace the internal hard drive with a 3.5" SATA drive.
What I need to know is am I correct about this? And is this the right kind of drive for my iMac? Are there any specifications I need to be aware of when ordering a new drive? I downloaded the manual explaining how to replace the drive and it looks doable. I would appreciate any guidance as to choosing the new drive (specific brand names/models would be great), installing the drive, and tips for formatting, etc. Thanks in advance for your help!

Welcome to Discussions - any 3 1/2" SATA drive will be fine, go to [macsales.com] or [smalldog.com] or [newegg.com] and choose whichever drive fits your wallet. Most of them are reliable, I have heard of problems with Seagate and Hitachi, but there are always some failures with any brand. Make sure to get a good warranty.Instructions will come with the drive, but you can download them from [Apple|http://www.apple.com/support/manuals/imac> as well.

My HD died and the Apple store installed the new drive and upgraded me to Mavericks. I no longer have iPhoto which I miss very much. How do I get it back and do I need it or do my pics go somewhere else? help

My Hard Drive died and when the Apple store installed the new drive they upgraded me to Mavericks. I no longer had iPhoto. Where do I get iPhoto, do I need it and where are my pictures going when they import??? Help I'm SO confused and frustrated. Thank you.

You need two items
1 - the iPhoto application -
You install it from the App Store
2 - and the iPhoto library - restore form your backup from just before the disk died - no importing involved - simply restore and launch iPhoto and it will look in the pictures folder and open it and it will be exactly the way it was when you made the backup
As to your question Do you need it - No you can manage your photos anyway you please - iPhoto is a good way but not required - you can use any software you want and you can import photos using image Capture (in your applications folder) or any other software you choose - If you use iPhoto then they by default going your iPhoto library - if you use other software then they go where you say to put them
LN

Installing on new drive and copying files to it

I have a Macpro with a 500GB drive running 10.5.4 that contains the OS, applications and my media. I would like to put either a 1TB or 2TB drive into it and put Snow Leopard on it and transfer all of my data and files (almost 450GB) to the new drive.
1.) How do I install the new OS on the new drive after I swap it out with the old one?
2.) What is the best way to copy all of my media and files to the new drive after the OS is installed?
Thanks.
Message was edited by: rick.pearl

Put the new drive in and keep the old one as well.
Boot from the SL DVD and install it on the new drive.
Once you boot in SL for the first time, use the Migration Assistant to transfer your stuff. Point it to the old drive.
You could also clone your old drive on the new drive using Supper Dupper and then upgrade to SL. If it was me that's what I would do, because I don't like Migration Assistant. But it's your choice..

Time Machine almost full, can I start a new drive and NOT delete old one?

Because I had an External HD crash, I was wondering if I can start a new External Hard Drive (500 GB) from scratch (meaning I don't copy old files to it) and keep the old one as a back up to the back up??? Also, I have NOT been backing up the applications and on the new drive, would like to do that. If I move the old stuff from the 300GB, won't the Applications take up most of the 500 GB??
Or is is simply better to copy everything over (I asssume it all remains on the old 300 GB hard drive) and simply let it start rewriting? My iMac is gettin on in years and I'd like to be prepared should something happen to it.
And as you can tell, I am not very techie so please feel free to talk down to me.
Has anyone migrated to a new External HD? I have directions from Apple, is it easy????
Thanks . . running out of space soon . . .

figleef wrote:
Because I had an External HD crash,
Just to be sure, do you mean your TM drive crashed? Or an external HD, containing data that TM was backing-up?
I was wondering if I can start a new External Hard Drive (500 GB) from scratch (meaning I don't copy old files to it) and keep the old one as a back up to the back up???
Again, I'm not sure what you mean. If you mean put the old TM drive "on the shelf" and start fresh on a new one, then yes. Eject and disconnect it, then format the new one (see Time Machine - Frequently Asked Question #5 if you're not sure how). Give it a different name, so you're sure which is which, then select it as the destination via the Time Machine Preferences window. TM will do a full backup to it, so may take a while.
The backups on the new drive will be completely separate from the old ones.
If you ever need to see or restore from the new ones, use the Browse Other Backup Disks option, per #17 in the above link.
I have NOT been backing up the applications and on the new drive, would like to do that.
Yes, it's usually not a good idea to exclude System or Applications folders.
If I move the old stuff from the 300GB, won't the Applications take up most of the 500 GB??
No -- your Applications folder is probably in the range of 10-20 GBs.wn to me.
Has anyone migrated to a new External HD? I have directions from Apple, is it easy????
Again, not sure just what you mean.

New drive and leopard

I got a new hard drive and cloned my old one using superduper.
Now I can't install leopard without partitioning my drive which it says
will wipe out my drive. Any ideas? I did not want to install all that again.

What system was on your old drive that you cloned? Did you make sure that the new drive was partitioned as GUID partition table before you cloned to it? It should also have a format of Mac OS extended Journaled. If it was not set this way at the start you will have to partition it correctly to upgrade.

Replaced hard drive and getting error

start up failed hard disk smart 0301
and quick scan 0303
i have everything backed up on my external.... this is the 2nd time i replaced the hdd... the 1st time it was under warenty
i have a hp pavillion dv5 -1251nr
i also have the op cd.... it was running vista.... help because i made the mistake of getting a sony netbook and its done for... my only chance to have a working pc is this hp.... and i am going insane without one

Contact the vendor of the new hard drive and request an RMA. Sometimes hard disks are received and the fail right out of the box. The manufacturers and vendors are aware of that. That is always a great reason to keep a receipt.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Storedge 3310, new drives, and an error

Similar Messages

Maybe you are looking for