STP blocking but status led green

hallo
I have some cat2950 with ios 12.1.22EA7 connected toghether with 3 VLAN and STP (PVST) configured.
On redundant links the STP shows correctly the blocking state of the interfaces but the STATUS LEDs are GREEN not amber.
The configs and the tree seems ok, the only strange thing is green leds !!
Could it be an ios bug or a config problem ?
francesco

I'm not sure this is normal as the earlier poster asserted. See http://www.cisco.com/en/US/partner/products/hw/switches/ps605/products_installation_guide_chapter09186a00800d9cfe.html#39834 for details on what the status LEDs mean. The relevant text is in Table 1-6:
/quote
Solid amber:
Port is not forwarding. Port was disabled by management or an address violation or was blocked by Spanning Tree Protocol (STP).
Note After a port is reconfigured, the port LED can remain amber for up to 30 seconds as STP checks the switch for possible loops.
/end quote
An STP blocking port is still active and functional, just not passing trafic. It needs to have Ethernet link to communicate in the spanning tree process in the event that it needs to change state. BUT, as the manual says, if it is STP blocking, it should be amber
Hope this helps. Please rate helpful posts.

Similar Messages

T60 will not power up (battery status led green, power status led green)

Ok so I have been researching this for a couple days now. Trying various things............
Including the famous 10 second power button press discharge.........
Symptoms:
1st Disclaimer - coffee was exploded all over the laptop but has been running for a month.
Symptoms:
It has been working post coffee spill (several weeks ago) as long as you left it running. I get cocky and turn it off then it wont come back on.
The laptop has exhibited the inability to power on since but I have been able to get it to turn on several times since.
green power light comes on with AC adapter only
plug battery in and the battery light goes green
press the power button - both lights go out
I replaced the keyboard, battery, tested for 20 Volts on the AC adapter, tested for 2-3 volts on the CMOS battery.
I tried testing for 20 volts on the motherboard where the power supply cable connects. I have most of the laptop broke down still.
I did get it running again last night as a result of me incorrectly using the multimeter and short circuiting the power supply connector .
It booted up and ran fine and I even tried turning it off and on again several times.
I thought it might be a heat issue. I turned it off and tried to turn it on this morning and it will not power up.
Same symptoms as before.
no battery, only power connected, green light comes on, plug in the battery, battery light goes green, try to turn it on and the lights go out.
It seems like it is fixable but I am not sure what to look for next.
Or should I be looking for another system board...........if so what should I replace it with
This is an IBM T60 Type 2613 15" screen.
Solved!
Go to Solution.

Welcome to the forum!
Your best bet would indeed be a new system board. Any single one from a non-widescreen T60/p will work.
I've got dozens of them available - send me a PM if you're interested.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Cisco 1131AG LWAP status led yellow and other leds blinking green

I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
The SSID broadcast is enabled.
On the switch the interface is up and there is traffic going in and out of the LAP.
I tired power reset and factory reset for the APs but the problem remains the same.
Any ideas for what might be the problem ?!!
Regards

Yes the clients are not able to see the SSID broadcasted by the AP.
But these APs were functioning normally before without any changes to the WLC config.
I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

Ultra 45 power/status led no display green light

Hi, i have a problem with my ultra 45. Wonder if anyone come across this. My system when booted will have the green led on but after awhile the led turns off when booting up. The system is able to run up and perform properly except the status led is off.
First i assume is due to the keyboard and mouse where i didn't connect properly but it does'nt seems to be the problem. I have search through the net and didn't found any useful solution. Hopefully i can get one here. Thanks
Edited by: kemwah on Sep 16, 2007 8:31 AM

Anyone got answer for this problem??

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Have 2 airport extreme base stations connected in chain. Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink. Anyone have any ideas?

Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
Power off the AirPort by pulling the power cord
Wait a minute or two
Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
Release the reset button and allow a full minute for the AirPort to restart
Now try to configure the AirPort again. If you continue to see the same symptoms as before, the AirPort will need to be replaced.

Overall status yellow, but technical status is green

We are on SAP BI 7.0, SP 17.
I am having an issue with a few DTP's. I am loading from a cube to 3 DSO's. The process was working correclty for quite a while, but lately has been running extremely long. For something like 7,000 to 8,000 records it takes only 43 seconds for the DTP to finish and the technical status to change to green. However, it takes 2 hours for the overall status to change to green and sometimes it doesn't at all and I have to set it to red so that I can delete it.
While it is trying to change the overall status to green the DSO is locked - I can't get into the DSO manage screen - gives me an error message about the locks. I have read some fairly similar posts already, but none that I have seen seem to have the exact issue as I'm having. Does anyone have any ideas why the overall status is not being updated?
I have tried re-activating the target DSO, source cube and DTP, but that didn't work. I also tried to create a brand new DTP, but that also didn't work. Also, this process is already in a process chain. I am compressing the cube on a weekly basis. Any help is greatly appreciated.
Thanks
Brett

Hi Brett.
We are experiencing similar problems. I am loading initial load from a DSO with a very high number of requests to a infocube.
Apparently there is a overflow of the lock table (SM12). There is a lock for each request in the DSO and when the number of locks reaches 3500 the DTP stalls. If I manually set the overall status to green, I get the lock table overflow error message.
I've told my basis team to increase the enque/table_size parameter, I'll let you if that has any effect.
Regards,
Lars

Data load from infoprovider : status is green, but no data is loaded.

Hi,
I have created a new application copying the planning application (which was again a copy from the apshell application set). I modified the dimensions, after which I wanted to load data from a BW infoprovider using the datamanager.
The first thing I noticed in the datamanager, was that the packages were not the same as in the original planning application. In fact I had chosen to copy all objects to the new application. For example, the package 'load data from infoprovider' that was contained in the data management map of the planning application, was not visible anymore in my new application. Instead, there is a package 'Loadinfoprovider' located in the system administrative map. As these packages are exactly the same, the package 'Loadinfoprovider' does not seem to work properly. When you run the package, it says that is has submitted records to your application, but when you run a report on it, or go look to the bpc infocube in BW, no data is visible.
Does anyone know what may cause this problem ?
Edited by: Wouter Vanhoutte on Dec 1, 2009 3:46 PM

Hi Wouter,
Did you check your transformation file?
I had the same problem once, my mistake was that I didn't add a line for my key figure amount (AMOUNT=ZAMOUNT). So the status is green but no data transferred because no key figure to transform.
I hope this will help you
Mathieu

Phone is totally unresponsive. But has power (green led flashing). Was OK this morning. Any ideas?

Phone is totally unresponsive. But has power (green led flashing). Was OK this morning. Any ideas?

Will47,
Help has arrived! Does the device have any physical/liquid damage? Was the device in use or being charged when this happened?
EfrainM_VZW
Follow us on Twitter @VZWSupport

FP 1601 status led shows red continuously

I am trying to use FP 1601 which was already configured long before. But now the status LED is continuously red .Power LEd is green and all other LEds are off. Am giving 24V power and checked that it is given to V and C properly .Ethernet connection is also proper. i tried to reset , but could not. i cant use it in anymore. can anyone help in troubleshooting

Hello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments

Charge status LED bug in new firmware

After updating my 2nd generation iPod shuffle firmware from version 1.0.2 (which it came with) to version 1.0.4, the status LED does not correctly indicate when the battery is fully charged anymore.
According to the manual, the status LED should turn from yellow to green only after the battery has been fully charged, which takes about four hours if the battery was completey depleted. It worked that way with the original firmware.
Now with firmware 1.0.4, the LED turns to green after a little less than 90 minutes of charging the empty battery, which by then obviously isn't full yet. From runtime tests I conducted it seems that the battery has reached about 85% charge at this point.
So if you want to ensure a full charge, ignore the LED and charge the iPod shuffle for at least four hours until Apple fixes this issue.

I went to local Nokia service, and they told me that probably it was wrongly flashed. So I reinstalled firmware two more time, but it always have the same problem. Is there someone with 6300 that have the newest firmware and can test this ?
thank you
I will put this phone to service and see what they will do.

MDS 9216 - showing red status LED, not starting up

Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,

As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike

How to turn OFF status LED on VC220?

I'm looking for a way to turn off the status LED on a VC220. This is not the IR LED, but instead the large blinking LED on the front.
The documentation mentions that it can be turned off, but I can't find a menu option for this.
Thanks for your help!
--Joe
Status LED
Indicates the following status:
LED Off—The power is off or the LED status is turned off.
Flashing green in one second intervals—The camera and network is functioning.
Steady orange—The camera can’t detect a networking signal; thus the camera is not functioning. For example, the Ethernet cable is not attached.
Flashing orange—The PIR sensor noted movement. Flashing green rapidly—The firmware is being
upgraded.
Flashing orange rapidly—The camera’s default settings are being restored.
Alternating flashing green and orange—Video has been lost.

Joe,
Use the Network Setting > IP Setting page to set the IP address and other related
settings. When you complete the configuration, click Save to save the settings;
otherwise click Cancel to discard the changes.
• Disable LED Operators—Select to disable the LED illuminators. You may
choose to do this if you don't want to alert others that the network camera is
on. Use the Network Setting > IP Setting page to set the IP address and other related
settings. When you complete the configuration, click Save to save the settings;
otherwise click Cancel to discard the changes.
http://www.cisco.com/en/US/docs/security/csbvsc/vc220/administration/guide/VC220AdministrationGuide.pdf
page; 41
Hope this is what you're looking for,
Jasbryan

Cisco 1131 access point status led

Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
Thanks

Here's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App

Status Led AP 1250 Ligthweight

Hi:
Somebody could you help me, a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
Thanks in advance for your help.
Regards

http://tiny.cc/uygtkw
Rating useful replies is more useful than saying "Thank you"

Notifications are not sent to some users, even after the status is green.

Hello
There are some notifications sent to many(4 to 5 users and i am one of them) users from the SAP system. And i can see in the SCOT transaction that the notifications are sent successfully to all the users. Status is Green(transmitted). But,the issue is that, Some users are getting the notifications and some(Incliding myself) are not.
The users who has mail id say for example [email protected] are getting the notifications within no time but some usres who has maild id like [email protected] are not getting the notifications even after a day.
There are two Nodes are active in the SCOT transaction, One is SMTP and other one is Dummy.
In the address area of the Node SMTP, around 11 users mail ids are maintained, which includes both type mail ids xxxxxxx@xyz and
[email protected]
And the * (star) is maintained in the address area of the Node Dummy.
Can you please give me some clue which can help me in resolving this issue.
Thanks for your time.
Chetan....

Hello Balaji,
Thanks for your inputs.
As i informed that, there are two nodes active in the SCOT transaction. Address area of the NODE A is already set as '*'. So, it was not possible for me to set the start * value in the address area of the NODE B. I dont think its possible to maintain * in Both the NODES.
In the Node A, we have maintained * and in the Node B we have maintained some users mail ids. Because, as this is Quality system we dont want everyone to get the notifications.
Thanks for your inputs.

STP blocking but status led green

Similar Messages

Maybe you are looking for