STP error on Cisco (uplink to Extreme)...

When I see this in a log:
On Cisco sw we get this error in logs:
*Feb 28 16:04:30.982: %SPANTREE-2-RECV_PVID_ERR:
Received BPDU with inconsistent peer vlan id 1 on GigabitEthernet0/1 on vlan 11.
*Feb 28 16:04:30.982: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet0/1 on vlan 1.
Inconsistent peer vlan.
*Feb 28 16:04:31.000: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet0/1 on vlan 11.
Inconsistent local vlan
Odd part is on the uplink side (Extreme 5i STP is disabled). The error means that onn the Cisco side it recv'd a packet that should of been vlan 11 untagged|?
It goes to a cisco 3548XL (really old IOS) when I have sw mo tr and sw tr en dot1 on its uplink.
Nornally between sw to sw we always have all vlans tagged...but for this setup to work I have to untag vlan 19 on the Extreme side and then add sw tr na vl 19 on the Cisco uplinik side, other wise not all vlan traffic passed. Any ideas? Vlan 11 is management vlan 19 is user vlan.

Thats the odd part, I have setup this up at diff sites 20+ times...but never with a Cisco 3548XL to an Extreme 5i, it shouldnt matter, but it does. I recv'd an old config from the LAN rtr and its does show all ports tagged....so its left to something funky on the Cisco.
0389-SW-Training-01#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5.1)XW, MAINTENANCE INTERIM SOFTWARE
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Thu 21-Dec-00 12:04 by devgoyal
Image text-base: 0x00003000, data-base: 0x00329E10
ROM: Bootstrap program is C3500XL boot loader
0389-SW-Training-01 uptime is 1 week, 5 days, 12 hours, 56 minutes
System returned to ROM by reload
System restarted at 19:33:53 PDT Tue Jul 17 2012
System image file is "flash:c3500XL-c3h2s-mz-120.5.1-XW.bin"
When I have sw mo tr (on Cisco gi0/1) which uplinks to Extreme 5i and have all ports tagged....the Cisco disables the uplink port to the Extreme for a vlan with the log error I posted earlier. Unfortunately its for a school district, so its picking up....so it might be a bit until I can get back out during a maintenance window. Thanks for the feedback. I have seen cases where this IOS is old and well needed udpate is probably in order, as you said.

Similar Messages

Errors in Cisco Collection Manager for SCE

I installed Collection manager and I got errors in logs:
[root@sce-cm ~]# tail -f /opt/cm/cm/logs/adapter-JDBCAdapter.log
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err (more details in next line), tag=4042321925, fieldNo-1=13 curSqlIndex=16, i=15
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.adapters.jdbc.JDBCAdapter - processRDR - got Throwable
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err - Exception while inserting the rdr values [0, 3, 71, 300, 300, 1338139200, 0, 1, 4, 8, 0, 0, 1], for the rdr tag = 4042321925
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err (more details in next line), tag=4042321925, fieldNo-1=13 curSqlIndex=16, i=15
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.adapters.jdbc.JDBCAdapter - processRDR - got Throwable
java.lang.ArrayIndexOutOfBoundsException
RPT_LUR table is empty.
How can I resolve this issue?
Version is 3.7.5

Hello Marat,
It seems that you might be hitting this one CSCtz20343.
Please check it.
Thanks,
Minja

Error in Cisco 2500 series Wireless Controller

I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

Error -6753 on my Airpot Extreme

Error -6753 on my Airpot Extreme. Changed from DSL to cable, and I have internet but when I connect my Airport Extreme into the system there is no connectivity. Using Bridge mode. Reset and started over thought I had it then it kicked out this error. Reset and reloaded defaults, the went through setup again, same result. I know it has to be one little setting as I'm new to cable internet.

What is the make & model of the other wireless router that you are connecting your AirPort Extreme to? Is this connection wired or wireless? What is your goal for the Extreme?

"IPSECcard: an error coming back 0x007F" error on Cisco 7206vxr router having SA-VAM2+

Hi,
I am getting "IPSECcard: an error coming back 0x007F" error on Cisco 7206vxr router having SA-VAM2+ having IOS c7200-jk9s-mz.124-19.bin & NPE-G1
The Configuration is like below
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
crypto ipsec transform-set kotakbank esp-3des esp-md5-hmac
crypto ipsec df-bit clear
Impact: After getting this error, the VPN tunnels are impacted.
Can any one tell us the solution ?.
Thanks...Pramod.

Upon replacing SA-VAM2+ issue got resolved... Thanks..

UC520 CCA 3.1 Error: com.cisco.nm.lib.cmdsvc.cmdsvc

I always get this error com.cisco.nm.lib.cmdsvc.cmdsvc when connecting to my uc520 and after this error nothing works right within CCA. I actually have to do a force close within task manager on the application to get it to exit out. I have done changes via ssh and I've heard that this can have an impact. how can I tell where in the config file the issues are and howto fix this?
thanks

Hi Jesse,
Sorry for the late reply
OK here is what I do, I always have a dedicated PC for running CCA (Yes sounds like an expensive way of doing it) but I normally use one of those <$200 laptops with a vanilla flavored Windows 7 install on it, I also turn everything off such as Firewall, UAC, AV etc..etc.. Then I install the latest version of Java and Flash onto it before installing CCA.
This is then my dedicated CCA building system, the only time you panic is when there is a new version to install, occasionally the upgrade causes unusual issues and to-date still do not know why. But all-in-all a dedicated system removes all issues and all possibilities of issues to a greater degree.
Following applications I run on this dedicated system to support the UC deployments:
CCA (Obviously)
PSPad (Free text editing software and very valuable)
Solarwinds or 3Cdaemon TFTP client
Cisco Configuration Professional (Just incase you have to work on any ISR's or 800 series routers)
Cute PDF if you want to turn Topology views into PDF for record keeping
Putty or my preferrence SecureCRT for CLI work
These are the basic essentials and a great place to start
Cheers,
David.
Message was edited by: David Trad

Error in Cisco call manager

Hi, I just installed the IPCC exprss in my call manager publisher. No error during the instalation.
But I got a error message in even log.
Cisco desktop enterprise
type: Information
Event ID: 2
SS3101 setup monitor failed connection failed, end

Please make sure that the Jtapi and Rmjtapi service users are ok (users password must be consistant with what you have within CallManager)

Error from Cisco Agent Desktop - The agent- or workflow-initiated action request failed.

We have roughly 20 agents using Cisco Agent Desktop version 85.1.417 and I have one that when she clicks the phone button to answer a call she gets the error: "The agent- or workflow-initiated action request failed."
I reinstalled the program, but she still receives the same error. What could be causing this problem?

This is what I found in the log:
2014-10-06 08:59:46:838 INFO VOIP2021 Desktop monitoring enabled for extension [9214].
2014-10-06 09:00:12:147 WARN STD3000 Get registry key <MTS_CitrixInstall> under path <SOFTWARE\Calabrio\CAD\Site Setup>. Object not found: <2:The system cannot find the file specified.>.
2014-10-06 09:00:12:159 INFO SOCKET0000 <CADEEMConnector> service on port <59015> has started.
2014-10-06 09:01:01:580 INFO PD4002 error while answering call ICDJtapiCallControlChannel (answer) error, invalid callId (17781617 != 37533406)
2014-10-06 09:09:28:543 INFO PD4002 error while answering call ICDJtapiCallControlChannel (answer) error, invalid callId (17781655 != 37533406)
2014-10-06 09:13:42:458 INFO PD4002 error while answering call ICDJtapiCallControlChannel (answer) error, invalid callId (17781669 != 37533406)
2014-10-06 09:29:03:809 INFO PD4002 error while answering call ICDJtapiCallControlChannel (answer) error, invalid callId (17781740 != 37533406)
I'm attaching part of the DBG log. I hope that it helps.
Thanks

Another kind of error, upgrading Cisco ISE 1.1.4patch3 to 1.2

I'm failing to upgrade our distributed ISE environment of 3 nodes.
Using ise-upgradebundle-1.1.x-to-1.2.0.899.i386.gz, MD5 sum is verified.
All nodes are running 1.1.4 patch 3 and the cluster is in sync.
Trying to upgrade secondary admin node first and get this error:
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Warning: Do not use Ctrl-C or close this terminal window until upgrade completes.
STEP 1: Stopping ISE application...
STEP 2: De-registering node from current deployment.
% Error: De-registering node from current deployment failed.
Starting application after rollback...
% Warning: Do the following steps to revert node to its pre-upgrade state.
-Ensure that node is still present in current deployment from Primary UI, if not present register this node back again.
error: %post(CSCOcpm-os-1.2.0-899.i386) scriptlet failed, exit status 1

Upgrading a Distributed Deployment to Cisco ISE, Release 1.2
http://www.cisco.com/en/US/docs/security/ise/1.2/upgrade_guide/b_ise_upgrade_guide_chapter_011.html
States that
Before You Begin
If you do not have a secondary Administration node in the deployment, configure one Policy Service node to be the secondary Administration node before beginning the upgrade process.
Upgrade the secondary Administration node from the CLI.
The upgrade process automatically deregisters Node Secondary Admin Node from the deployment and upgrades it to Release 1.2. Node Secondary Admin Node becomes the primary node of the new deployment when it restarts. Because each deployment requires at least one Monitoring node, the upgrade process enables the Monitoring persona on Node B even if it was not enabled on this node in the old deployment. If the Policy Service persona was enabled on Node B in the old deployment, this configuration is retained after upgrading to t

Decode Error in Cisco VCS for a call from Jabber to telyHD

Hi,
We have the following setup:
Cisco Jabber <---> Cisco VCS <---> telyHD (Our Video Product)
Now, the call works well when the call is intiated from telyHD to Cisco Jabber.
But, the call fails when the Cisco Jabber initiates the call towards telyHD.
The packet capture on VCS shows that there is a syslog message from VCS to Jabber indicating the following when 180 Ringing is received from telyHD:
Message [truncated]: tvcs: Event="Decode Error" Service="SIP" Src-ip="10.1.1.19" Src-port="5060" Dst-ip="10.1.11.11" Dst-port="25331" Detail="(User-Agent) Single header User-Agent appeared twice in message" Protocol="TCP" Level="1" UTCTime
Can you please help in troubleshooting this issue. I don't see multiple "User-Agent" headers in the 180 Ringing sent by telyHD.
I have attached the packet capture on VCS.

I am also having the same issue. Can someone please respond? Thanks.

Error in Cisco Application Desktop

I have the following error when i install the Cisco Agent Desktop application(CAD) with version 7.02 release 3 and i am using cisco call manger 4.2(3) and IPCC Enterprise version (7).

file that is creating the error is put down during the base install of the agent/supervisor package. This file lives in the c:\windows\system32 directory once the install is completed correctly. I would recommend that you use the add/remove program tool in windows to remove the agent software first. Second, remove the supervisor if installed. Last would be to remove the agent base software. Once removed, you can remove the Cisco directory under c:\program files. Reboot the desktop system and reinstall.

Error in Cisco LMS

Hi,
I get this error when i run some actions in CISCO LMS 3.2 i.e if I click in Campus Manager - Start Data Collection. it gives error " you are not access to request this action ".
What can be the problem?
Please find the attachment for your reference.
Please Suggest. waiting for your prompt reply.
Thanks

to fix the database issue , you need to reintilaze the ANI database:
1) Stop the daemon manager
"net stop crmdmgtd"
2) Go to NMSROOT\CSCOpx\bin.
NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
for linux:
/opt/CSCOpx/bin/dbRestoreOrig.pl dsn=ani dmprefix=ANI
3) Wait for a few minutes before starting the CW daemons again:
"net start crmdmgtd" (wait for at least 5 minutes before using CW again)
Thanks-
Afroz
***Ratings Encourages Contributors ***

Help, error connection Cisco Identity Services Engine with AD, global catalog port status error

Dear all,
I have Cisco Indentity Services Engine, that connected to Active Directory. When I test connection detailed,
the result is error, said:
Test Connection Results
This dialog shows the detailed logs for the operation for: idsv0018.
Status: FAILED: Global Catalog port status error.
Can anyone help?
I believe, because this error, I can't search group of AD, at Cisco ISE.
FYI: the connection from Cisco ISE to AD, joined with successful result.
Thanks,
Jerri

It's clears that when ISE tries to find the GC using the _gc._tcp. DNS query. It doesn't find that information on the Domain controller. The GC information is missing on the DC.
gc._tcp.DnsForestName
Allows a client to locate a Global Catalog (gc) server for this domain.
Jatin Katyal
- Do rate helpful posts -

Error Installing Cisco VPN CLIENT 5.0.02.0090 on Domain Connected Client

When installing the Cisco Client version 5.0.02.0090 I get an error when installing it on a Windows XP PC that's connected to a Windows Server Domain.
More INFO:
Windows XP Dutch SP2
Connected to Windows 2000 Domain
Works on another Dutch Windows XP SP2 system that is NOT connected to a domain!
Last lines of the setup logfile:
Property(S): CURRENTDIRECTORY = C:\DOCUME~1\J6299~1.HIE\LOCALS~1\Temp\RarSFX0
Property(S): CLIENTUILEVEL = 2
Property(S): CLIENTPROCESSID = 4232
Property(S): VersionDatabase = 200
Property(S): VersionMsi = 3.01
Property(S): WindowsBuild = 2600
Property(S): ServicePackLevel = 2
Property(S): ServicePackLevelMinor = 0
Property(S): MsiNTProductType = 1
Property(S): WindowsVolume = C:\
Property(S): RemoteAdminTS = 1
Property(S): GPTSupport = 1
Property(S): OLEAdvtSupport = 1
Property(S): ShellAdvtSupport = 1
Property(S): Intel = 15
Property(S): PhysicalMemory = 2046
Property(S): VirtualMemory = 3448
Property(S): AdminUser = 1
Property(S): LogonUser = j.hiemstra
Property(S): UserSID = S-1-5-21-3206282357-3970063792-383977586-1104
Property(S): UserLanguageID = 1043
Property(S): ComputerName = FMGPCHIEMSTRA
Property(S): SystemLanguageID = 1043
Property(S): ScreenX = 1280
Property(S): ScreenY = 1024
Property(S): CaptionHeight = 19
Property(S): BorderTop = 1
Property(S): BorderSide = 1
Property(S): TextHeight = 16
Property(S): ColorBits = 32
Property(S): TTCSupport = 1
Property(S): Time = 15:09:38
Property(S): Date = 3-1-2008
Property(S): MsiNetAssemblySupport = 2.0.50727.1433
Property(S): MsiWin32AssemblySupport = 5.1.2600.3019
Property(S): RedirectedDllSupport = 2
Property(S): DATABASE = C:\WINDOWS\Installer\42637aeb.msi
Property(S): OriginalDatabase = C:\DOCUME~1\J6299~1.HIE\LOCALS~1\Temp\RarSFX0\vpnclient_setup.msi
Property(S): UILevel = 3
Property(S): ACTION = INSTALL
Property(S): CsProp_CopyInstHelperDll = 1
Property(S): CsProp_LogViewer = Non-Existant
Property(S): CsProp_VPNClient = Non-Existant
Property(S): CSPROP_MSTCPIP = 1
Property(S): CsProp_RebootNeeded = 2
Property(S): ROOTDRIVE = C:\
Property(S): CostingComplete = 1
Property(S): OutOfDiskSpace = 0
Property(S): OutOfNoRbDiskSpace = 0
Property(S): PrimaryVolumeSpaceAvailable = 24732144
Property(S): PrimaryVolumeSpaceRequired = 43556
Property(S): PrimaryVolumeSpaceRemaining = 24688588
Property(S): PrimaryVolumePath = C:
Property(S): SourcedirProduct = {871DF2BE-41D2-4334-AC33-839AF16FC8FE}
Property(S): CsProp_GetDriveType = 3
Property(S): GROUP_USERS = Users
Property(S): GROUP_INTERACTIVE = INTERACTIEF
Property(S): GROUP_LOCAL_SYSTEM = SYSTEM
Property(S): GROUP_ADMINISTRATORS = Administrators
MSI (s) (9C:78) [15:09:38:041]: Note: 1: 1708
MSI (s) (9C:78) [15:09:38:041]: Product: Cisco Systems VPN Client 5.0.02.0090 -- Installation operation failed.
MSI (s) (9C:78) [15:09:38:041]: Cleaning up uninstalled install packages, if any exist
MSI (s) (9C:78) [15:09:38:041]: MainEngineThread is returning 1602
MSI (s) (9C:30) [15:09:38:056]: Destroying RemoteAPI object.
MSI (s) (9C:50) [15:09:38:056]: Custom Action Manager thread ending.
=== Logging stopped: 3-1-2008 15:09:38 ===
MSI (c) (88:68) [15:09:38:072]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1
MSI (c) (88:68) [15:09:38:072]: MainEngineThread is returning 1602
=== Verbose logging stopped: 3-1-2008 15:09:38 ===
See attachemend for Error.
I get the error after the 'next' when the setup is 'ready to install', so after selecting the destination folder.
It happens in the Screen 'Updating system'
Oh yeah, I just install it from the C:\ Drive and not from a network path. Tried extracting the exe manualy also, nothing seems to help..

I'm seeing the same error on our domain connected machines (Windows XP - German).
Adding the Users and INTERACTIVE accounts fixes the install issue, but the install process takes a few minutes to complete and the there are a lot of queries to the DCs.
Is there a fix?

Internal Rx Errors: on gig uplinks (CSS11150)

Has anyone ever ran across what causes "Internal Rx Errors:"? I've noticed that this counter is increasing quite rapidly, after clearing the interface stats first of course. This is occuring on my uplink interfaces (e13 and e14) which are the gig interfaces on the CSS. I've found an explanation of the errors in the CSS documentation:
"Internal RX Errors
The number of frames for which reception on the interface failed due to an internal MAC sublayer receive error."
But I'm still a little unclear about how to go about how to rid the CSS of these errors as well as what is and isn't acceptable as a threshold for these errors.
Thanks in advance,
cdeeds

We have encountered the same errors on our CSS11150's.
Configuration #1:
Servers <-GigE-> Cat4006 <-GigE-> CSS11150 <-FastE-> Firewall.
In configuration #1, the "Internal RX Errors" for the GigE ports on the CSS were indicate drops due to contention for slower egress ports (ingress is GigEthernet, egress is FastEthernet). We have decided to use configuration #2 (we no longer use the CSS GigEthernet ports). We are letting the Cat4006 switch take care of the GigE-to-FastE buffering, but this does not appear to have improved the situation.
Configuration #2:
Servers <-GigE-> Cat4006 <-FastE-> CSS11150 <-FastE-> Firewall.
With configuration #2, the CSS is no longer logging the "Internal RX Errors" for the GigE ports. Instead, the Cat4006 is now logging "txQueueNotAvailable" errors for the FastEthernet port connected to the CSS.
Basically, GigE flow control doesn't seem to work between our servers and the Cat4006 and CSS switch ports. Luckily, all of the sensitive/critical applications hosted on our servers run on TCP (which takes care of retransmission)!
Hope this makes sense...
Dan

STP error on Cisco (uplink to Extreme)...

Similar Messages

Maybe you are looking for