STP view on Topology diagram of LMS 4.2

Hi all,
I am using LMS 4.2 and I am using topology services. I that I want see stp topology of my LAN and I want to see the which ports are blocked by STP. Is it possible to see STP blocked ports on Topology view of LMS 4.2.2?
Note: I am using PVST ( per vlan spanning tree )| on my LAN .
Thanks,
Selva .

Hi
You have to enable RMON to measure bandwidth utilization.
Take a look on the Monitoring and Troubleshooting With Cisco Prime LAN Management Solution 4.2 guide.
Begining on the page 7-43 you can find the procedure.
Hope you can set it

Similar Messages

Bandwidth utilization on topology diagram of LMS 4.2

Hi,
I am running LMS 4.2 , using that i am monitering some switches . I am using topology services also . In that i am getting veiw of all connected devices with links. But bandwidth utilization is for those links are not showning in topology veiw .
Is there any settings to be done in LMS 4.2.2 or any configuration changes to done on my switches ?? to find the traffic flow bandwidth utiliztion.
thanks ,
pandian .

Hi
You have to enable RMON to measure bandwidth utilization.
Take a look on the Monitoring and Troubleshooting With Cisco Prime LAN Management Solution 4.2 guide.
Begining on the page 7-43 you can find the procedure.
Hope you can set it

Building Topology Diagrams in Flex 2

Hi All,
I want to build a topology diagram in Flex 2. Is it possible? I wanna have a set of images which cud be drag - drop enabled. I should be able to link the different nodes in the hierarchy based on its status with Arrows(different kinds). And each node(represented by diff images) will have its own set of properties (could be referred from the database.). How do i go about doing this. Awaiting your suggestions and possible links to such existing prototypes.
Thank you

Hi grace,
I want to build topology diagrams in Flex 2. Is it possible? Are there any prototypes like TWaver built on Flex 2? Twaver is built on Flex 3 and i cant use it on Flex Builder 2....
P.S: I dont have Flex 3 SDK or Flex Builder 3 and i cant even avail it any time sooner.

L3 topology diagram with a large number of networks

I am working on redesigning a network that is using a single class B network for there LAN workstations and servers. I proposed for them to separate the two and put all of their servers into one class C network and the workstation in another class C. They stated that they wanted 14 separate networks for the workstations, different for section of the building, and 28 for the servers. The reason for the 28 is due to the fact they didn't keep track of how they used their address space and they do not want to renumber servers due to firewall rules. I have 50 networks hanging off of the collapsed core switch "WS-C6513-E" and finding room for all of these network is quite difficult. Does anyone have any experience with creating network topology diagrams with a large amount of networks hanging off of one device? I have attached a doc of what I have done.

Brandon
Sorry, you did say that in the last bit of your first post.
Last time i was doing topology diagrams i believe Visio had a pop up function where you could click over it but obviously if you are printing them out that does no good.
Unless you can summarise them to one entry with a note of how many subnets are being used within the summary i can't think of a way to do it. You could match the vlan number to the subnet (which you have partly done) and then just list the vlan numbers with the network prefix and make a note the subnet is derived from the vlan number.
Jon

Topology diagram of installed agents on grid control

Hi,
Can anyone help. I have grid control with a number of clients (agents) installed. Does anyone know of a way to get a topology diagram out of grid which shows all the connected systems.
regards
Alan

Hi Alan,
You might find the following post is helpful. That's a introduction for a tool to show topology diagram for Oracle Application Server. FYI.
[http://www.oraclepoint.com/topic_600]
R.Wang
[http://www.oraclepoint.com]

Topology diagrams - advice on doing this type of work?

I'm considering a contract position where I'd be doing topology diagrams and maps..Can anyone who has done or is doing this type of work offer any suggestions/advice for making this work go well?
And I'm thinking along the lines of maybe...re-useable geometry...I suppose swatching for colors and styles for objects...just thinking out loud here..
I'm sure that after awhile, I'll develop my own work patterns for this..might be nice to see if anyone has any "tips and tricks" to share.
Thank you!
John

jdanek;
well I resonate with your questions...so far, I don't have all the granular details, but I have to think that I'll be given some standards, and I know that I will produce this art from supplied sketches.
I did google this and found that the spectrum went from playful/whimsical (think: kid's textbook) to the more serious and accurate, just a few steps short of full-on cartography.
I don't yet know where this client falls on that spectrum.
Probably be a good idea for me to develop a list of questions for them, maybe request some links so that I can see what ball park I'll be working in.
thank you!

Building/editing topology diagrams - any ideas/advice?

Hi,
I'd like to build a web application that is capable of displaying & editing topology diagram (e.g. a network diagram with applications too). Effectively to have a graphically web based means of allowing a user to add nodes & relationships to represent a topology such as the following [http://performancepointinsider.com/files/planning/planningtopology.png|http://performancepointinsider.com/files/planning/planningtopology.png] . So the model basically consists of nodes and relationships.
Any ideas/advice on how best to do this, e.g.:
Q1. Any open-source project that does something similar?
Q2. Best way of handling the graphical aspect of the application?
(e.g. prototype, extjs, etc?)
Thanks

Hi Eric,
I want to build topology diagrams in Flex 2. Is it possible? Are there any prototypes like TWaver built on Flex 2? Twaver is built on Flex 3 and i cant use it on Flex Builder 2....
P.S: I dont have Flex 3 SDK or Flex Builder 3 and i cant even avail it any time sooner.

View tables relationship diagram

I am using Oracle 9i R2. Is there any way to view the Relationship Diagram of the schema.

Below is free tool that will generate ER diagrams
from an Oracle database.
http://www.schemester.co.uk/
Yeahh but beware that it may generate something crazy if you have many schemas with the same set of tables i.e. it obviously could not understood that there can be many relationships with the same, just in different schemas. At least it was the case the last time I used it.
OK here is the link where you can find quite a bunch of such tools http://www.databaseanswers.com/modelling_tools.htm
After Oracle Designer at least for me every other tool looks like sucker but it's hard life and my today's company isn't using Designer and I have to suffice either with Rational Rose (quite usable) or Visio (complete nightmare at least for ER diagrams with more than 5 tables).
Gints Plivna
http://www.gplivna.eu

Problem Topology Data collection LMS 4.1

Hi there,
I have an issue with the lms 4.1 Topology Data Collection. In the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary, there are only 2 devices succeeded and 0 device fail. but I have more 500 device in state managed. I run Inventory Collections but the number doesn't change.
Inventory Collection          534                13 02 May 2012, 11:07 CEST Idle          Schedule
Config Archive                         507               14 02 May 2012, 09:51 CEST Running          Schedule
Topology Data Collection               2               0 02 May 2012, 11:11 CEST Idle          Schedule
I have read others discussions but no one has the same problem or similar problem. The only possible solution is to reset the ANI db but I'm not sure if it it's the best solution.
Any ideas?
Thaks for help

I confirm that Martin. Good spotting!. I just noticed it in a server I installed yesterday. These 2 lines were added to the hosts file.
127.0.0.1       localhost
127.0.0.1   LMS4
A bit silly for both, since these entries were allready in the hosts file, done by the windows install I think
127.0.0.1       localhost
::1             localhost
Cheers,
Michel

Can not use Topology services in LMS 3.1

Hi all,
I'm using LMS 3.1 with Campus manager 5.1 and install on solaris platform. When i click on topology services in campus manager, i have received a message as below
Please help me resolve this error
Tks,
HTTP Status 500 -
type Exception report
message
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
org.apache.jasper.JasperException
     org.apache.jasper.servlet.JspServletWrapper.handleJspException(JspServletWrapper.java:453)
     org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:393)
     org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:314)
     org.apache.jasper.servlet.JspServlet.service(JspServlet.java:264)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
     com.cisco.nm.cmf.util.AccessLogFilter.doFilter(AccessLogFilter.java:100)
root cause
java.lang.NullPointerException
note The full stack trace of the root cause is available in the Apache Tomcat/5.5.17 logs.

Post the NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log in addition to the output of the pdshow command from this server.

Unable to launch Topology Services in LMS 4.1

When I try to Launch Topology Services from windows 7 client I am getting the following error message:
Cannot connect to ANIServer: ANIServer7.0-CCADLMS001
Attached is the screenshot for reference. Also attaching the SC QUERY and SYSTEMINFO files.
I have done the following steps so far:
Open the orb.properties file.
Windows: NMSROOT\lib\classpath
where NMSROOT is the directory where you have installed Cisco Prime LMS.
Set the property as follows:
jacorb.dns.enable=off
Go to Admin > Trust Management > Local Server > Certificate Setup.
The Certificate Setup page appears.
Enter the IP Address of the Cisco Prime LMS Server in the Hostname textbox.
Populate the other columns as explained in the Online help for Administration of Cisco Prime LAN Management Solution 4.1.
Click Apply to generate the self-signed certificate.
Restart the daemons by net stop crmdmgtd and net start crmdmgtd
checked the firewall settings and in the client and server. Tried disabling firewall also. No go.
Please help.
Regards,
Ramakrishnan Natarajan

I confirm that Martin. Good spotting!. I just noticed it in a server I installed yesterday. These 2 lines were added to the hosts file.
127.0.0.1       localhost
127.0.0.1   LMS4
A bit silly for both, since these entries were allready in the hosts file, done by the windows install I think
127.0.0.1       localhost
::1             localhost
Cheers,
Michel

Error in viewing the Workflow Diagram Applet thru Workflow Monitor

Hi!
I am receiving the following error while viewing the applet-based workflow diagram.
IOException while fetching datajava.io.FileNotFoundException: http://172.16.24.1:7777/pls/wf/WF_MONITOR.GetProcess?x_item_type=NIS_WEB&x_item_key=6192&x_admin_mode=yes&x_access_key=3620278198&x_proc_name=&x_proc_type=
Java Character Set is:8859_6
java.lang.NullPointerException
     at oracle.apps.fnd.wf.Database.parseData(Database.java:121)
     at oracle.apps.fnd.wf.Database.<init>(Database.java:101)
     at oracle.apps.fnd.wf.Monitor.init(Monitor.java:303)
     at sun.applet.AppletPanel.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
This error is logged thru the Sun Java Console found on the browser.
I need to check the diagram to check if the workflow transaction successfully go thru the workflow nodes.
Any idea regarding this? Thanks in advance!

Hi,
Cause
====
Server Time zone profile option is not set and the Framework is expecting it to be.
Solution
To implement the solution, please execute the following steps:
1. Set the profile option Server Timezone.
2. Bounce the Apache Server.
Retest the issue.
Regards,

How to view router/switch logs using LMS 3.2?

Of course I can log into each of my 100 routers and switches and peforms "sh loggin" to look for problems, but how do I use LMS 3.2 to consolidate all those logs into one location? Can I set up something so I can see those logs in more or less real time?
Thanks in advance.

>> Does LMS go get syslog messages periodically or does the device send a copy to LMS whenever it generates a new message?
The latter.
If for some reason, the devices cannot log directly to LMS, there're a few options: 1) Devices log to a central syslog server, which in turn exposes the syslogs to LMS' Syslog Analyzer, either via the Cisco-supplied Remote Syslog Collector or some unsupported methods such as NFS mount, or 2) Install Syslog-ng on the central syslog server, relay the logs to LMS, as described in this whitepaper: http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/white_paper_c11-571038.html
>> What's the benefit of scheduling a report to run automatically? Is it saved somewhere that is easier/quicker to get to?
It's the usual benefits of automation. Scheduled syslog reports apparently write outputs to /var/adm/CSCOpx/files/rme/cri/archives/syslog/reports/output/[jobID_runID], on Solaris, for example. The structure inside is rather muddy. So it might be easier to have something like a VBscript to screen-scrape the LMS web GUI for the report outputs instead.
>> Can new syslog messages from devices be posted to an RSS feed?
That's a novel idea. Though obviously not from the devices directly, it most likely coud be done through some "syslog2rss" relay residing on the syslog server. I think the potential volumes of logs could be too much for RSS, unless careful filtering/deduplication takes place on the relay before posting to a feed.

RAR - management view - Role Analysis diagram shows zero

Hello,
we were able to run the Full Sync for role/user/role and Batch Risk Analysis user/Role/Profile and Critical Acess to completion successfully.
In the Informer tab, Managerment View, the risk Violations and Users Analysis shows reasonable figures. However the Role Analysis , it shows zeros for the risk violations and risk violations for user and roles.
Could someone point out where is likely the problem so i could go and check ?
Thanks
CL

Hi Lee,
Have you run Management Report Job as well?
Regards,
Sabita

LMS 4.2 Topology View

Hi
I have installed LMS 4.2 in one of my customer site. We have added all the switches and everything works perfectly. Recently we added all the CCTV cameras in lms.
Issue is that when CCTV camera is down it takes a long time to show in topology map..Any one knows how to make view in topology map as real time. Atleast a delay of 30sec is okay..
Regadrs
-Danish

Topology view is not really intended to be a real time (or near real time) fault management tool. While you can turn up the speed of it's discovery cycle, it will create excessive workload and, depending on the size of your network, may result in polling never stopping due the time to complete one cycle being more than the time you have configured to start over again.
To see near real time faults (such as loss of a CCTV camera), have operators refer to the Fault Monitor display:
http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/mnt-faultbrowser.html
If you want to customize the polling of devices for fault management, refer to the Fault Management chapter of that same guide:
http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/mnt-fault.html

STP view on Topology diagram of LMS 4.2

Similar Messages

Maybe you are looking for