Strange Ad-Hoc Issue

I've been getting this Ad-Hoc warning on the WLSE, the name is PwC80211 and the MAC keeps changing on it except the manufacurer code. I've read where this is probably a Linux OS and it's scanning for other Ad-Hoc's to connect to. Has anyone else every seen this before?

I knew of two laptops running Linux in the area of the reporting AP. I asked both users to please check their configurations and after that, I haven't had it reappear. I am assuming that one was incorrectly configured and was running in ad-hoc mode. I used location manager to gauge the general area of where the ad-hoc might be located. One laptop runs Linux exclusively, the other is a dual boot XP/Linux. I believe it was the Linux only laptop that was misconfigured. It either was a driver issue or configuration, the user fixed it, but if it ever reappears I'll know where to find it.
My WLSE reported the same thing filling up the log with hundreds of incidents until I tracked it down. You will see the manufacturer part of the MAC never changes, that might help you find the culprit. If you have location manager setup, use the "TX Coverage By Signal Strength w/o Overlaps" to find the distance of the ad-hoc from the reporting access point(s).
I had another instance last week where some consultants were doing an audit and had two laptops talking to one another using "hpsetup" and neither of them even knew it. I also found "tmobile" and "linksys" on one laptop. Here is a good article about it.
http://www.nmrc.org/pub/advise/20060114.txt
Good Luck

Similar Messages

Creating Custom Fields on Ad-Hoc Issues in GRC PC

Hello All -
We have a requirement to create a custom field on ad-hoc issues in GRC Process Control 10.1. I have created custom fields on test plans and controls previously, but have not created custom fields on ad-hoc issues. I have not been able to find any SAP documentation that states whether or not custom fields can be created for ad-hoc issues. Has anyone done this? If yes, can you please share any documentation on how to create these custom fields for ad-hoc issues? Thanks in advance!

Hi Taylor,
Procedure to add a Customer Defined Field (CDF) in any screen of Process control is same. You only need to change is..object name. Did you refer to the below SAP Note which helps to define CDF?
1655539 - Add user-defined fields
If not, please review this and add the custom field in adhoc issue page. You can also review the below SAP Notes which has the latest fixes for this area once you are able to manage the CDF in the page.
1934382
1928603
1924077
Thanks & Regards
Neeraj

InDesign 5.5: Strange Printing Transparency Issues

Hi guys, long time reader, first time poster. This forum has helped with a lot of problems, so thanks, and hopefully you can help with this one.
I'm working on a multiple-spread page for a client that is giving me some strange issues when it's printed. The document has an image as a background for the entire page, and then a black box over the image with some text on top of it. For some reason, the black box with text is letting the image underneath show through, almost as if the box is 99% transparent or something. I've checked each box individually, and there's nothing in the transparency/attributes boxes. I'm not sure how, exactly, to solve this issue -- is there some sort of universal transparent image setting (for instance, set black to 99% opacity always or something similar)?. It's the only thing I can think of.
InDesign CS5.5, OSX Lion. The files are a combination of TIFF and JPG images, and I get the same issue no matter what image format is underneath.
Any feedback is welcome here.

No problem, Peter. I've included a few shots from various pages (the problem stems to all black boxes placed over images over the 64 page document) on the links below.
http://img40.imageshack.us/img40/5964/88392023.jpg
http://img94.imageshack.us/img94/9741/93991019.jpg
http://img20.imageshack.us/img20/7883/10837728.jpg
The third one is the page that I took the picture of the printout with my phone.
I've tried this on an offset press and a digital press; with 'knockout group' ticked and not. For the life of me, I can't understand why the black is still overprinting on the image when it shouldn't be.

Strange audi sync problem & different, stranger video sync issu in sequence

I have two strange occurances with one particular set of media that was downloaded from the same original source mini-dv (recording in dvcam) tape. I have not found the same issue on any other footage.
1) when the media is imported into FCP, the audio is out of sync. it is slightly out at the beginning and then gets progressively worse.
2) when this footage is used in a sequence, the video that show in the sequence is not the same as the video that is exported when this sequence is exported as QT movie (or any other export option) Like the audio the video out of sync gets progressively worse.
- The original media is perfectly in sync looking at the digitized source ie: in Quicktime. There is no audio out of sync problem.
- the only difference I could see in the file was that this media is 3.5mb data rate whereas all the others are 3.6mb.
- other tapes from the same camera do not have a problem
- I do all my downloading from a firewire deck and not from the camera
- I upgraded from 6.0.1 to 6.0.4 (as did the QT 7.5 upgrade also) to see if that fixed the problem but to no avail.
Very perplexing. I managed to work around this problem in a sequence whos deadline was looming by manually slipping the footage in the sequence the required number of frames. This is where it also gets odd. I was able to do this by
- double click the clip in the sequence which then loaded that into the viewer.
- position the playhead at the beginning of the clip
- from the canvas select the go to position in master clip option which then loaded the masterclip into the viewer. the position in the masterclip was always the correct frame (ie the frame I expected to see as per my edit). The frame showing in the canvas was also the correct frame (but this would not be the case when exported)
- the next thing i did was to use the slip tool, as soon as i held the slip tool over the sequence clip, the frame in the canvas would be the wrong frame (the frame i would see when I exported).
- then i would just carefully slip the sequence clip back to the matching correct frame. So watching in the viewer, I would align the frame that showed in the viewer to the frame in the canvas.
When done the frame showing in my sequence would be a completely different frame but when exported, the frame that I expected to see would be the exported frame.
I could find no logic to the amount I needed to slip each time (I am sure there is logic but I couldnt figure out what that was). the clip at the end of the footage needed to be slipped -10:09, and this got progressively smaller to the clip at the beginning of footage needing to be slipped -:16
Hopefully that wasnt too confusing.

btw, i have tried recapturing the footage and i have offlined it, copied it to another location and onlined it in the new location to no avail. still have the sync and video in sequence issues.

Strange Wi-Fi issue in Mountain Lion

Hello Mountain Lion Gurus/Users/All,
Just yesterday I upgraded my 2009-mid-MacBook Pro to Mountain Lion (from Lion)
I have this strange issue.
I turn on my Wi-F
Selected my home network from the list of all the networks Mac could find. (Actually this is the network I regularly use on all my devices.)
It gets connected to my home network over Wi-Fi for 6 to 7 seconds. (I am able to browse pages, as a test, in these 6 to 7 seconds).
Suddenly message pops up saying "Connection Timeout. Could not connect to network." Where as, I am able to browse over the same network from other devices like my iPod Touch, Android :@ Device etc.
Please help me.
Chandra

Chandra,
Some people have found that setting a network location prevents this kind of problem.
In System Preferences, choose Network. Then Edit Location, the + sign and use any name for the location. Then select the location in the Network preferences pane. If you haven't already, joint the wifi network.
You should also check that you haven't inadvertently messed up your settings in the advanced portion of the preferences. While you're in there, click the button to renew your DHCP lease (in the TCP/IP tab).
Jim

Strange CPU Performance issue Mac Pro, Logic 7.2.3......

Hi there,
I am experiencing a strange issue with Logic 7.2.3 and my Mac Pro.
I am running about 70 tracks in a tune I'm writing, with a lot of the EQ and dynamics processed on a Liquid Mix, but am experiencing a lot of CPU spikes, and drop outs in logic.
The System Performance meters are showing that one of the CPU cores is at full capacity, whilst the Activity Monitor is showing a total usage of about 40%.
http://www.ephexis.co.uk/images/cpu-grab.jpg
I have tried every combination of settings in the audio preferences, but cannot seems to get this track to play properly.
With 71 tracks, this machine is currently LESS powerful than the G5 that I have been working on until purchasing the Mac Pro.
I there anything else I can try? Are there any other means of controlling buffer size?
I have a suspicion that this may have something to do with the Plugin Delay Compensation set to 'All' - But without doing this, I cannot use the DSP effects of the liquid mix to work on a Bus! Very frustrating.
Many thanks for the help, any ideas at would be deeply appreciated,
Adam Ephexis
Mac Pro 2.66, 2GB, 1.5TB -=- MacBook Pro 2.16, 1GB, 100GB Mac OS X (10.4.8) Liquid Mix, Fireface 800, Apogee MiniDAC, Creamware A16 Ultra

Great!
Thanks for the tips guys.
I have tried to find an offending loop or part in the sequence, but cannot find anything at all thats causing the issue.
My suspiscion is that using the focusrite Liquid mix on a part, that is in turn going into a delay compensated bus, which has another Liquid mix plugin on it, is causing the issues. I use the total mix software in the fireface to perform the summing of the busses, which I think in turn may be causing the PDC to glitch a bit more.
Which is a bit annoying, as the mix in this tune is my best yet!
So I will attempt to remove the liquid mixes that are running in series in a chain, and see if thats the problem, but if that fails, time to re-format again!
I'll let you know how I get on in the next couple of days!
Thanks again,
Adam
Mac Pro 2.66, 2GB, 1.5TB -=- MacBook Pro 2.16, 1GB, 100GB Mac OS X (10.4.8) Logic 7.2.3 - Fireface 800, Focusrite Liquid Mix, Apogee MiniDAC, Creamware A16 Ultra

Strange power-on (issue?) with K8N Neo4 Platinum

Hi all, i have a new K8N Neo4 Platinum, non-sli.
My rig:
A643000+ winch, no overclock
2x512MB Corsair XMS DDR400MHz
2x200GB Seagate mirroring
Plextor PX-708A
BenQ DVD Burner
AN OLD Matrox Mystique 4MB PCI (new pci-e gfx card later...)
A powerfull enermax coolergiant 600W ATX 2.0 power supply
Latest official nforce4 drivers and bios
It seems to be ok: installed winXP pro sp2 and updates, installed two Seagate in raid-mirroring with the nforce4 controller, installed some progs and utils, firewall is ok, prime95 go without problems for 1 our (more tests later), cpu temp is 34°C and sys temp is 30°C.
CoreCenter Say:
Vcore -> 1.41V
3.3V -> 3.39V
+5V -> 5.13V
+12V -> 12.26V
memory volt -> 2.60V
FSB -> 200MHz
PCI-E -> 100MHz
cpu volt -> By-VID
Apparently no weird things...
When i switch-on the Pc, for some seconds( ̃10 secs) it don't want to boot, optical drives blink repeatly and the screen is blank, like a bad overclock... But the machine isn't overclocked, and the bios is ok, i think. After 10 secs, finally it go and run flawlessly, post and other things are ok. When i reboot in win, the 10secs-issue repeat itself. So this strange thing at the post is normal? Anyone with the same "problem"? For now the rig is ok when it logon in winXP...

Hi all my friends
@JER101 >>> Ehrr i mean post, sorry
I had unplugged the optical drives, but the problem persist. When plugged, they blink for some times and after blinking the machine go into post-phase and after it boot in the correct manner. I think the PCI card is the problem, like some of you said... I will buy one pci-e card (obviously), but i hope things are not dangerous for now
In the mean time, i have a new problem: emule+firewall=BSOD. I know, there are tons of post about this issue around, but the solution is unclear... Tried to disable DEP, patched WinXP SP2 with latest things from winupdate, but nothing work for me, emule and the firewall generate a crash&reboot. Tried with the Marvell LAN, too, without success.
Any suggestions? Usefull links? If i uninstall the "NVIDIA Forceware Network Access Manager" it will work without problem with a thirdy part firewall, like sysgate?
P.S.
What's the problem with nvidia drivers? C'mon nvidia, solve this damned issue!

OSD Strange Driver injection issue "Process completed with exit code 2147500037 OSDDriverClient"

Hi,
We got an strange issue with computer model z400 and Z420. With the memory setup 16 GB RAM we get an faild driver injection. But If we have 8 GB RAM, Everything works fine. We have tested the memory, with no error. And It is same for every delivered
HP Z420 with 16 GB (4*4GB RAM).
Strange? Any feed back?
SCCM 2012 R2 CU1, Deploying Windows 7 x64 Enterprise
I found this on the z400 installation I dont know what driver fails on z420
Deploying drivers to down-level operating systems in WinPE 4.0 or a later version fails
https://support.microsoft.com/kb/2853726/en-us?wa=wsignin1.0
Drivers in "D:\_SMSTaskSequence\Packages\PSS0015B\3494DEEA-917A-47BC-80C8-2E6C8B6A8986 is
"TITLE: Broadcom NetXtreme Gigabit Driver for Microsoft Windows 7 (64-bit) VERSION: 14.2.0.5 Rev. A"
smsts.log
Adding "D:\_SMSTaskSequence\Packages\PSS0015B\3494DEEA-917A-47BC-80C8-2E6C8B6A8986" to Windows driver store. OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Setting %SystemRoot% to "D:\WINDOWS" OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Getting namespace "Microsoft-Windows-PnpCustomizationsNonWinPE" for architecture "amd64" OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Added list item with key value '1' OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Writing configuration information to D:\_SMSTaskSequence\PkgMgrTemp\drivers.xml OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Successfully saved configuration information to D:\_SMSTaskSequence\PkgMgrTemp\drivers.xml OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Setting temporary directory to 'D:\_SMSTaskSequence\PkgMgrTemp'. OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Calling Package manager to add drivers to the offline driver store. OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Command line for extension .exe is "%1" %* OSDDriverClient 2014-11-24 13:50:21 1040 (0x0410)
Set command line: "X:\WINDOWS\system32\dism.exe" /image:"D:" /windir:"WINDOWS" /apply-unattend:"D:\_SMSTaskSequence\PkgMgrTemp\drivers.xml" /logpath:"D:\_SMSTaskSequence\PkgMgrTemp\dism.log" OSDDriverClient 2014-11-24
13:50:21 1040 (0x0410)
Executing command line: "X:\WINDOWS\system32\dism.exe" /image:"D:" /windir:"WINDOWS" /apply-unattend:"D:\_SMSTaskSequence\PkgMgrTemp\drivers.xml" /logpath:"D:\_SMSTaskSequence\PkgMgrTemp\dism.log" OSDDriverClient 2014-11-24
13:50:21 1040 (0x0410)
Process completed with exit code 2147500037 OSDDriverClient 2014-11-24 13:50:47 1040 (0x0410)
uExitCode == 0, HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osddriverclient\sysprepdriverinstaller.cpp,548) OSDDriverClient 2014-11-24 13:50:47 1040 (0x0410)
Dism failed with return code -2147467259 OSDDriverClient 2014-11-24 13:50:47 1040 (0x0410)
AddPnPDriverToStore( pszSource, sTargetSystemDrive, sTargetSystemRoot, wProcessorArchitecture), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osddriverclient\sysprepdriverinstaller.cpp,658) OSDDriverClient 2014-11-24 13:50:47 1040
(0x0410)
Failed to add driver to driver store. Code 0x80004005 OSDDriverClient 2014-11-24 13:50:47 1040 (0x0410)
InstallDriver( iInstallParams->sContentId, iInstallParams->sSource, iInstallParams->pBootCriticalInfo ), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osddriverclient\driverinstaller.cpp,557) OSDDriverClient 2014-11-24 13:50:47 1040
(0x0410)
/SaiTech

Hi, here is the DISM look like Intel driver ("Intel(R) Active Management Technology - SOL" and Intel Storage ) are the issue, it is strange
dism.log I just dump some small snipit from the log with error:
2014-12-08 08:50:15, Info                  DISM   PID=1588 TID=1608 Successfully loaded the ImageSession at "X:\WINDOWS\System32\Dism" - CDISMManager::LoadLocalImageSession
2014-12-08 08:50:15, Info                  DISM   DISM Provider Store: PID=1588 TID=1608 Found and Initialized the DISM Logger. - CDISMProviderStore::Internal_InitializeLogger
2014-12-08 08:50:15, Info                  DISM   DISM Provider Store: PID=1588 TID=1608 Failed to get and initialize the PE Provider. Continuing by assuming
that it is not a WinPE image. - CDISMProviderStore::Final_OnConnect
2014-12-08 08:50:15, Info                  DISM   DISM Provider Store: PID=1588 TID=1608 Finished initializing the Provider Map. - CDISMProviderStore::Final_OnConnect
2014-12-08 08:50:16, Warning               DISM   DISM OS Provider: PID=1272 Unable to copy msxml6.dll from the client executable folder to the dismhost.exe folder. Relying on
in-box version. - CDISMOSServiceManager::RunASICompatibilityShim
2014-12-08 08:50:49, Info                  DISM   DISM Provider Store: PID=1272 Loading Provider from location D:\_SMSTaskSequence\PkgMgrTemp\27CE6ED8-7378-49E1-A55A-D9F63653368C\PEProvider.dll
- CDISMProviderStore::Internal_GetProvider
2014-12-08 08:50:49, Warning               DISM   DISM Provider Store: PID=1272 Failed to Load the provider: D:\_SMSTaskSequence\PkgMgrTemp\27CE6ED8-7378-49E1-A55A-D9F63653368C\PEProvider.dll.
- CDISMProviderStore::Internal_GetProvider(hr:0x8007007e)
2014-12-08 08:50:49, Info                  DISM   DISM Provider Store: PID=1272 Failed to get and initialize the PE Provider. Continuing by assuming that it
is not a WinPE image. - CDISMProviderStore::Final_OnConnect
2014-12-08 08:50:49, Info                  DISM   DISM Provider Store: PID=1272 Finished initializing the Provider Map. - CDISMProviderStore::Final_OnConnect
2014-12-08 08:50:49, Info                  CBS    Transactions disabled in registry, continuing without transaction support.
2014-12-08 08:50:49, Info                  CBS    Kernel transactions are disabled, continuing without transaction support.
2014-12-08 08:50:49, Info                  CBS    Failed to find a matching version for servicing stack: D:\Windows\WinSxS\x86_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_0b0e4b4025cf4049\
[HRESULT = 0x80070490 - ERROR_NOT_FOUND]
2014-12-08 08:50:49, Info                  CBS    Failed to find servicing stack directory in online store. [HRESULT = 0x80070490 - ERROR_NOT_FOUND]
2014-12-08 08:50:49, Info                  CBS    Must be doing offline servicing, using stack version from: D:\Windows\WinSxS\x86_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7601.17592_none_0b0e4b4025cf4049\cbscore.dll
2014-12-08 08:50:50, Info                  DISM   DISM Driver Manager: PID=1272 Found 1 driver package(s) at 'D:\_SMSTaskSequence\Packages\PSS00A89\0F5E1730-0EEF-42C3-9CF4-240927FC36DA'.
( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:50, Info                  DISM   DISM Driver Manager: PID=1272     Driver Package 'D:\_SMSTaskSequence\Packages\PSS00A89\0F5E1730-0EEF-42C3-9CF4-240927FC36DA\E1Q62x64.INF'
( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:50, Info                  DISM   DISM Driver Manager: PID=1272 Installing driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\0F5E1730-0EEF-42C3-9CF4-240927FC36DA\E1Q62x64.INF'
to the currently offline OS ... ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Imported 'D:\_SMSTaskSequence\Packages\PSS00A89\0F5E1730-0EEF-42C3-9CF4-240927FC36DA\E1Q62x64.INF'
to offline driver store at 'D:\Windows\System32\DriverStore\FileRepository\e1q62x64.inf_amd64_neutral_751f9117acd25de0\E1Q62x64.INF'. ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\0F5E1730-0EEF-42C3-9CF4-240927FC36DA\E1Q62x64.INF'
installed! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Successfully marked devices for reinstall! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Installed '1' drivers. ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 RETURN InstallDriversOffline (0) ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Attempting to delete [{bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/config/SOFTWARE\Microsoft\Windows
NT\CurrentVersion\UnattendSettings\PnpUnattend] registry key. - CDriverManager::Internal_DoUnattendCleanup
2014-12-08 08:50:53, Info                  DISM   DISM Driver Manager: PID=1272 Successfully deleted [{bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/config/SOFTWARE\Microsoft\Windows
NT\CurrentVersion\UnattendSettings\PnpUnattend] registry key. - CDriverManager::Internal_DoUnattendCleanup
2014-12-08 08:50:53, Info                  DISM   DISM Image Session: PID=1272 Disconnecting the provider store - CDISMImageSession::Final_OnDisconnect
2014-12-08 08:50:53, Info                  DISM   DISM Provider Store: PID=1272 Finalizing the servicing provider(DISM Package Manager) - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SOFTWARE
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SOFTWARE,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SYSTEM
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SYSTEM,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SECURITY
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SECURITY,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SAM
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SAM, the
client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/COMPONENTS
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/COMPONENTS,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/DEFAULT
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/DEFAULT,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Users/default/ntuser.dat
2014-12-08 08:50:53, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Users/default/ntuser.dat, the client
may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:50:53, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/smi/store/Machine/schema.dat
2014-12-08 08:50:53, Info                  DISM   DISM Package Manager: PID=1272 Finalizing CBS core. - CDISMPackageManager::Finalize
2014-12-08 08:50:53, Info                  DISM   DISM Provider Store: PID=1272 Disconnecting Provider: DISM Package Manager - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:50:53, Info                  DISM   DISM Provider Store: PID=1272 Found the OSServices. Waiting to finalize it until all other providers are unloaded.
- CDISMProviderStore::Final_OnDisconnect
2014-12-08 08:50:53, Info                  DISM   DISM Provider Store: PID=1272 Finalizing the servicing provider(MsiManager) - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Found 2 driver package(s) at 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78'.
( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580     Driver Package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrl.inf'
( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580     Driver Package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrle.inf'
( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Installing driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrl.inf'
to the currently offline OS ... ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Imported 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrl.inf'
to offline driver store at 'D:\Windows\System32\DriverStore\FileRepository\mesrl.inf_amd64_neutral_229186b6de98a42e\mesrl.inf'. ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrl.inf'
installed! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Successfully marked devices for reinstall! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Installing driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrle.inf'
to the currently offline OS ... ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Imported 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrle.inf'
to offline driver store at 'D:\Windows\System32\DriverStore\FileRepository\mesrle.inf_amd64_neutral_0899484a86551e82\mesrle.inf'. ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Driver package 'D:\_SMSTaskSequence\Packages\PSS00A89\15CBA2EA-EE6D-408B-B19F-AB36F67E7B78\mesrle.inf'
installed! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Successfully marked devices for reinstall! ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Installed '2' drivers. ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 RETURN InstallDriversOffline (0) ( HRESULT = 0x0 ) - DriversCallback
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Attempting to delete [{bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/config/SOFTWARE\Microsoft\Windows
NT\CurrentVersion\UnattendSettings\PnpUnattend] registry key. - CDriverManager::Internal_DoUnattendCleanup
2014-12-08 08:51:25, Info                  DISM   DISM Driver Manager: PID=1580 Successfully deleted [{bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/config/SOFTWARE\Microsoft\Windows
NT\CurrentVersion\UnattendSettings\PnpUnattend] registry key. - CDriverManager::Internal_DoUnattendCleanup
2014-12-08 08:51:25, Info                  DISM   DISM Image Session: PID=1580 Disconnecting the provider store - CDISMImageSession::Final_OnDisconnect
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Finalizing the servicing provider(DISM Package Manager) - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SOFTWARE
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SOFTWARE,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SYSTEM
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SYSTEM,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SECURITY
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SECURITY,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SAM
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/SAM, the
client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/COMPONENTS
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/COMPONENTS,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/DEFAULT
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/System32/config/DEFAULT,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Users/default/ntuser.dat
2014-12-08 08:51:25, Info                  CBS    Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Users/default/ntuser.dat, the client
may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
2014-12-08 08:51:25, Info                  CBS    Unloading offline registry hive: {bf1a281b-ad7b-4476-ac95-f47682990ce7}D:/Windows/system32/smi/store/Machine/schema.dat
2014-12-08 08:51:25, Info                  DISM   DISM Package Manager: PID=1580 Finalizing CBS core. - CDISMPackageManager::Finalize
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Disconnecting Provider: DISM Package Manager - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Found the OSServices. Waiting to finalize it until all other providers are unloaded.
- CDISMProviderStore::Final_OnDisconnect
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Finalizing the servicing provider(MsiManager) - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Disconnecting Provider: MsiManager - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Finalizing the servicing provider(IntlManager) - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Disconnecting Provider: IntlManager - CDISMProviderStore::Internal_DisconnectProvider
2014-12-08 08:51:25, Info                  DISM   DISM Provider Store: PID=1580 Found the PE Provider. Waiting to finalize it until all other providers are
unloaded. - CDISMProviderStore::Final_OnDisconnect
/SaiTech

Strange sqlloader loader issue with carriage return in Unix

Oracle 10g
Solaris
Hi All, I'm having issues in running some data into a table via sqlloader. The data was extracted using concatanated SQL with a | delimiter. sql script was executed in the shell to produce the data file.
eg
a,b,c|
d,e,f|
The control file specifies a string terminator as "str '|\n'" but when i run the sqlloadr command on the unix box I states that
no terminator found after TERMINATED and ENCLOSED field.
Ive tried it with \n\r same sort of issue.
The strange scneario i encountered was when I just specified "str '|'" as I read unix would default to \n, the weird thig was that my 6 records DID load into the table succesfully but a bad file was produced with a | character in it and the log file specfied that it tried to load 7 records where 6 were succesfull and 1 failed even though I only had 6 record to play with in the 1dst place.
Any ideas / thoughts greatly appreciated?!
Kind regards
Satnam

Hi All,
Ive updated the problem..with some output... essentially Ive get it to a situation wher I load ALL my records into the table but I still get a bad file with a "|" record issue and the log file still syas that Im trying to load 7 record when I only have the 6 records.
...............SQL statment...
set trimpspool on
set feedback off
set heading off
set linesize 500
set pagesize 0
spool loaddata_FP.lst
SELECT '"'||spart.x_lsm_region||'"'||','||
'"'||spart.x_sub_type||'"'||','||
'"'||spart.x_origin_type||'"' ||'|'
FROM siebel.cx_ls_part_ship spart;
spool off
-- sample of control file
load data infile 'loaddata_FP.lst' "str '|'"
into table siebel_data_fp fields terminated by "," optionally enclosed by '"'
(x_lsm_region,
x_sub_type,
x_cust_face_staff,
x_nature_partner,
x_origin_type)
--sample log file with error why is it telling me I have 7 records when I am processing 6?
value used for ROWS parameter changed from 64 to 22
Record 7: Rejected - Error on table SIEBEL_DATA_FP, column X_SUB_TYPE.
Column not found before end of logical record (use TRAILING NULLCOLS)
Table SIEBEL_DATA_FP:
6 Rows successfully loaded.
1 Row not loaded due to data errors.
0 Rows not loaded because all WHEN clauses were failed.
0 Rows not loaded because all fields were null.
--- sample bad file showing the pipe ... whay is sqlloader trying to process this pipe when its part of the record...
/u01/oracle/admin/adhoc/xxxl(TESTxx)$
/u01/oracle/admin/adhoc/xxx(TESTxx)$ vi FCT_PARTNERSHIP_ldrcontrol.bad
"FCT_PARTNERSHIP_ldrcontrol.bad" [Incomplete last line] 2 lines, 213 characters
|
~
~
~
any help appreciated!
Edited by: spliffer on 04-May-2010 05:06

E1200 strange wireless speed issue

I posted this on another forum and thought I'd post it here as well.
Currently have Comcast's Performance tier internet and usually get anywhere from 22-27mbps down and 4-5mbps up which has treated us well.
Xfinity SMCD3GNV gateway modem in bridge mode so I can use my own router
Desktop #1 is hard wired to router
Desktop #2 is wirelessly connected (has Asus PCE-N15 wireless NIC in it - driver up to date)
Macbook wirelessly connected
Xbox 360 S hard wired to router
Nokia Lumia 900 wirelessly connected
I have a few different routers (Asus rt-n56u, Linksys e1200, Linksys WRT54GL all with latest firmwares) that I mess with far too often and am having a weird issue with the e1200. What I found is that when I am using the e1200 every device works fine and gets the normal speed (22-27 down/5 up) except desktop #2. The speeds are absolutely atrocious. Even the WRT54GL which is wireless G smokes the e1200, but only on desktop #2. I thought it might be a setting which is different than when I test the other routers, but I make sure they are all the same. The download speeds sometimes barely get to 5mbps but upload speeds are fine on desktop #2 with the e1200 whereas with the WRT54GL and rt-n56u the download speeds are 20+mbps. Would anyone have any idea why this would be? Just kind of strange that every device works as it should other than one computer with the e1200, but that computer isn't effected when the other routers are tested with the same settings. Things I have tried are:
-Made sure the router was running the latest firmware
-Made sure the wireless adapter had the latest driver
-Rolled back the driver on the wireless adapter
-Turned off ipv6 in the wireless adapter settings
-Changed the channel width on the router from auto (20/40) to strictly 20mhz
-Changed wireless channel from auto to 1,6,11
-Toggled WMM on and off
All of these things made no difference for desktop #2 and it can only achieve around 3-5mbps with the e1200. The Asus is probably a faster router overall, but I'd sort of rather use the e1200 IF I can figure this problem. Thanks for your time!

Just checked the options for the wireless card and unfortunately that isn't an option. For "wireless mode" the only options are: IEEE 802.11b, IEEE 802.11b/g, and IEEE 802.11b/g/n. Of course I have it set to the last option and the speeds are still the same. I have included a url to screenshots of each of the settings so maybe someone can point out something that might help. Thanks for your time.
http://imgur.com/a/TV92L#0

Strange packet loss issue

Hi all,
I am having a strange issue with my macbookpro recently. Here is the situation.
I have the TP-LINK wireless router both at home and work. IP address of this unit is 192.168.3.1 at home.
Recently i noticed a very high level of packet loss (60-70%) from my macbook pro when i pinged the default GW wireless router. I first thought its a wireless issue and tried debuging the issue from that end. I used my brother's macbook and he wasnt having this packet loss when i pinged from his terminal.
I then very randomly connected to my remote VPN server and noticed that the packetloss has disappeared when the VPN is connected and ping a remote IP such as 8.8.8.8.
Now i have two terminals running, one with a normal ping to 8.8.8.8 which goes via VPN and has 0% packet loss. Another terminal running a ping via interface en1 outside of the VPN interface using "ping -S 192.168.3.102 192.168.3.1" and this terminal is showing the same 60% packet loss.
Also strangely, this issue is only noticed at home router and not at work. At work the normal connection without VPN works fine.
I am at loss for ideas what could be causing this issue all of the sudden when the same settings were fine for over a year.
Any ideas?
Thanks

No solutions yet... I doubt this is a hardware matter as the packet loss goes away almost instantly when i switch on the VPN or simply move to other networks... The strangest thing is the VPN connection that solves the packet loss.. One thinks if VPN is overlaying on en1 to make its connection, how come the packetloss ceases to exist once there is a peer2peer connecton active to the same interface with the packet loss issue. Very strange indeed.
I thought also this could only be a ICMP issue (ping protocol) however ever the browsing slows down when im normally connected to this network.
In some awkward way im happy someone else is reporting this as I thought this is a weird enough problem for no one to comment on for yearly 10 days...
Im going to run a tcpdump to see if there is anything strange moving abount on my interfaces whilst there is a packet loss... will inform if any interesting results appeared...

Strange IIS redirect issues... leads to /jakarta/isapi_redirect.dll

This is quite strange... the majority of my IIS redirects are working, but this one for some reason is odd.
www.myserver.com leads to www.mynewserver.com no problem... works as it should.
www.myserver.com/about leads to www.mynewserver.com/about ... again, works as it should.
however, this is weird.
www.myserver.com/main.cfm leads to www.mynewserver.com/jakarta/isapi_redirect.dll
I'm trying to figure out why, how can I fix this so that
www.myserver.com/main.cfm leads to www.mynewserver.com/main.cfm

Maybe my instance of this might help clarify: I was working off of the following stack overflow link's accepted answer and also got the jakarta/isapi_redirect.dll issue. (I'm working with Windows Server 2012, IIS 8.5, and CF 11).
IIS HTTP to HTTPS relative redirect - Stack Overflow
After some "change setting, restart sites, test, change setting back and change different setting, restart sites, test" combinations, I found that this combination worked: (It actually matches what Erik99 said to do, but I didn't understand I only needed to change a single application pool.)
Real site (HTTPS binding only, actually contains code and virtual directories)
Application pool's Advanced Settings > Enable 32-Bit Applications : False
Http_Redirect site (HTTP binding only, is a blank shell of a folder with no directories)
Application pool's Advanced Settings > Enable 32-Bit Applications : True

Strange Numbers Sync Issue to Icloud

It's strange that even if i don't make any changes to a Numbers document, it tries to sync itself to icloud every time I open > view > close a document.
Anyone have this issue and help me?
Thank you.

kozmikoda wrote:
Thank you, but previous version of Numbers didn't has this issue.
I opened, viewed and closed. There was not any syncing when I didn't change anything in the document.
I think this is a bug developers don't know.
I suppose it is possible, but as far as I know if you are using iCloud, it has always behaved this way. There has never been a strictly manual sync.
You can always turn off iCloud for Numbers adn turn it back on when you wish to sync if it is that much of an issue for you.

Strange mpc segfault issue

When I went to do my usual `mpc playlist | grep` method of looking for a song to play, I got a strange error...
http://pastebin.com/m6d72296f
Curious, I ran regular old `mpc playlist`. What I got was 310 lines of the expected output followed by "Segmentation fault", and was returned to my bash prompt. I decided to go out on a limb and see if it would treat root the same way. To my surprise, `mpc playlist` worked with no issue, as did my usual grep-ing.
I went back and made sure the permissions on my music directory were good, made sure I had plenty of RAM, recreated the MPD database, everything. I don't understand what's up. At first I thought it was a kernel issue so I `pacman -Syu`'d and restarted, only to find the issue was still there.
Any suggestions?

Same here, I noticed it some time ago when i piped the output to dmenu...
It also occurs when you redirect the output to a file or anywhere else.
I haven't found a solution yet, have you asked the devs or the mpc mailing list (if there is one) yet?

Strange XFCE time issue

Hey,
I use the Xfce Clock built into the Xfce package. There seems to be a bug in the latest version, I noticed it the other day, in 24-hour mode it messes up the presentation of time. However it 12-hour mode it so far seems okay (Needs confirming)
At 6:15PM it showed 10:15. At 8AM the time jumped to 00:00. The issue was fixed when I returned home at 3PM. When I saw the xfce update come through Pacman just now, I updated and rebooted in hope this would be a fix.. unfortunately not. I rebooted the machine I updated, still no help.
I use Xfce on both Desktop and Laptop, Both of them have this issue. The desktop uses Ntp, and the laptop uses hwclock. It is a very strange ordeal and I'm not quite sure how to respond.
-Drumm

I'm not sure what's going on but I do not have a problem and have not had one in the past. Using XFCE on i686 (with ntp) the clock is fine in both 24 hour and 12 hour style. It displays the correct time. My system is fully up-to-date.
edit: when you see the problem what do "date" and "date -u" show?
edit: there is now a thread on the ML regarding this issue in LCD mode. A bug report is being submitted. In LCD mode 8 is being displayed as a 0. I have just replicated the problem.
Last edited by loafer (2012-01-25 19:38:16)

Strange Ad-Hoc Issue

Similar Messages

Maybe you are looking for