Strange clicking building up

I have a piece of music which has a strange echoing click appearing in same place even when I have no music regions/tracks playing ( all muted) but the clicking fades in at the same point everytime. it starts in around a minute and slowly builds up gaining a bit of noise and continues until I hit stop! Where could it be comin from ?

Hello Upakrik, Thanks for reply. I think I have found problem. I had tape delay on a particular track and was using feedback on the tp delay whicch seemed to cause the prob! turned off the tape delay and the prob was gone so just re did the delay with new adjusts and seems fine again! Gawd knows what this is caused by. logic seems to hang onto the delay and play it back even when all tracks are muted! Not all the time I hasten to add. I had another track with delay but didnt adjust feedback and that was fine. I tried the interface route too and the prob was there with internal speakers too. So adjusting the feedback on the fly seems to start it. Ah well, yet another bit of hair pulled out! Merry Christmas.
M

Similar Messages

  • Strange clicking sound on my Lumia 930 arround the...

    When my camera is not activated, if I mildly shake my Lumia 930 I can hear a strange clicking sound on the upper part of the device, just arround the camera lense. Can it be the lenses just shaking, because when the camera is activated  that sound disappears.

    Hi, Tomislav5. Welcome to Microsoft Mobile Community. How long have you been noticing this issue? Did you change any settings on the device that may cause this to happen? Make sure that the system apps on the device are all updated. You may check it by going to Store > ... > settings > check for updates. You may also try rebooting your phone by pressing and holding the volume down and the power keys at the same for 10-15 seconds and see if it makes any difference. you may need to set the date and the time after this operation. We'll wait for your response.

  • IMac G5 wont turn on, strange clicking sound

    Brought my iMac home from work (where it was working fine). Plugged it in and it wont turn on. I hear a strange clicking like sound and then that stops. Help!

    Hello and Welcome to Apple Discussions. 
    You should try booting from the OS X install disc. Then open Disk Utility from the Utilities Menu (don't run the installer). I fear something has gone awry with your hard drive.
    Let us know how you get on.
    mrtotes

  • Keynote:  I'm attempting to tweak a presentation I did on my old PC in ppt.  When I click build inspector, then build, I do not get an effects drop down window.  Please advise

    Keynote:  I'm attempting to tweak a presentation I did on my old PC in ppt.  When I click build inspector, then build, I do not get an effects drop down window.  Please advise

    Here's the Keynote forum:
    https://discussions.apple.com/community/iwork/keynote

  • Strange clicking/tapping sound in the background of my music in my iTunes player.  Any idea how to make it stop?

    There is a strange clicking sound in the background of my music in my iTunes player.  It sounds a bit like a horse galloping faintly in the background trying to keep up with the music!  Any idea of how to make it stop?  It doesn't matter what I'm listening to, doesn't happen in between songs, and has never happened in the 4 years I've owned this iMac.
    Thanks for your help!

    AND yea i afraid to sync my iphone and lose everything ;( i had everything perfect sync ing perfect ical,contacts,mail,apps and now sence new library I dont wana lose everything.....my hole life runs on my fone i need help bad

  • Strange clicking noise

    Hello all. I hope someone can help me with this question.
    I have a 30g ipod that is less than a year old. I believe I purchased it last October. It has started to make a strange clicking noise when I play music.
    I tend to use it alot since I can listen to music at work. I would say that it runs for about 9 hours a day. Most of the time when it is in use, it is hooked up directly to the speakers and the battery charger.
    Has anyone else had this happen? Does anyone know what the problem is?
    Thanks for your help.
    Dakota
      Windows XP  

    Hi Dakota!
    First, have you tried resetting your iPod? To reset an iPod:
    First, toggle your iPod's "Hold" switch back and forth a couple of times (leave it on the white side of the switch).
    Then, press and hold the Menu and Select (center) buttons together for 5-10 seconds.
    You might need to attempts this quite a few times. Also, if you connect your iPod to your computer or another power source while resetting, that can be more effective.
    If resetting doesn't help, then I would suggest that you try restoring your iPod in iTunes.
    For info on restoring, see this article about it:
    Restoring Fifth Generation iPod - (iPod with video)
    -Kylene

  • Desktop makes strange clicking noises when resuming from hibernation

    Hi  I have a three week old HP Pavilion Desktop 2022 running Windows 7 Home Premium.    I have noticed over the last few days that if  I leave it in hibernation mode for quite some time, when I wake it up Windows starts perfectly but I get 7 or 8 strange clicks from the desktop unit itself.   The desktop doesnt do this during normal startup or restart only when coming out of sleep or hibernation??  Does anyone else have this issue?  Is it normal as I realise whilst in hibernation the fan is not running and it has been extremely warm.  It does sound a bit like  a cooling noise but hope someone can reassure me regarding my concern.  Thank you, all answers are apprecaited.

    I'm gonna just say it - Hibernate doesn't work all the time. I've never trusted it, never used it and recommend that no one use it. 
    there got it out of the way.
    Why did I say that - If you don't plug anything into your PC (cameras, printers, scanners, phones, etc) Or load any other software except for updates from MS and your virus protection, then Hibernate works awesome...
    but as soon as anything is added... that app or piece of hardware needs to conform exactly to all the Hibernate specifications and sometimes they don't and they cause some problems.
    So the fact that you had a bluescreen means something isn't playing nice. That dump file can be evaluated, but I would start isolating the problem by removing any hardware you've added to see if that helps.
    Or - don't use Hibernate - shut it down when you don't use it, and power on when you do
    hope that helps and that I don't sound to terrible
    good luck
    bill
    I'm a HP employee

  • Strange clicking noise with audio in Final Cut Express?

    I recently imported some new audio in to FCE. When I previewed it, the audio played fine however when I added it into the timeline there was a strange clicking/tapping noise playing with the audio? It is in MP3 format and I've never had a problem with using MP3 format in FCE before? If the audio format needs to be changed how do I do it?

    You can convert the audio to the correct format for FCE by using Quicktime 7.
    Open the MP3 file in Quicktime 7 and then go to the menu File > Export.
    From the drop down menu on the Export pane, choose Sound to AIFF.
    Click the Options Button and once the options pane opens choose:
    Click OK, then save  the exported file to a location of your choosing.
    Import the file you just converted into FCE and you should be good to go.
    MtD

  • Help! Instead of my project's audio, I hear strange clicking sounds

    I've been editing a video for a while and the audio's been fine... then all of a sudden it stopped working (not on mute or anything) and all I can hear are these strange clicking noises when I stop or start the playback...I feel like I probably just pressed a button by accident and that it's a simple thing to correct but I'm clueless as to how to go about it. Does anyone have any ideas?

    I think apple doesn't support using siri while driving.
    Cause it can distract you from driving.

  • FaceTime making strange clicking sound

    FaceTime making strange clicking sound
    When FaceTime calls from my MacBook through my iPhone 5 work its a great feature. When it fails, extremely frustrating. I often experience a loud clicking sound when trying to place calls. I can be heard by the person I am calling but I can't hear them, only the clicking. Restarting worked for months to eliminate clickling which seemed to happen after using the headphone port now nothing seems to work predictably, even lost all sound from attempted calls today even after restarting although everything worked fine yesterday. Running MacBook Pro (13-inch, Late 2011) with OS 10.10.2 and an iPhone 5 with 8.1.3. Would love to see a permanent fix that includes the ability to see voicemail messages on my Mac.

    Send Apple feedback. They won't answer, but at least will know there is a problem. If enough people send feedback, it may get the problem solved sooner.
    Feedback
    Or you can use your Apple ID to register with this site and go the Apple BugReporter. Supposedly you will get an answer if you submit feedback.
    Feedback via Apple Developer

  • X220 Ultrabase external USB HDD strange click sounds on boot

    I have X220 and Ultrabase 3. External USB HDD (WD Passport) is connect to one of Ultrabase USB ports. When I reboot and press F12 to get the boot menu there are two strange click (or scratch) noises coming out of the external HDD. One click before the menu appears and second after boot device (CD drive) is selected. I tried different HDD with the same result. It loooks like a short power drop or so but it happens with the boot menu only. The first external HDD I used for three years is damaged now, don't know whether it is connected with this issue. BIOS version 1.38, no USB 3 port. I found the issue is specific to Ultrabase USB ports. When the same external HDD is connected directly to notebook USB port, it is fine. I use the Ultrabase setup for booting from Acronis TrueImage bootable CD to create backups. Anyone has similar issue ? Is possible to use the notebook USB port when it is docked in Ultrabase ?

    It could be that the port where it does not function may not be producing sufficient power for the given HDD.  It has been shown that all USB ports do not output the same power.  You might test with a USB 'Y' connector or a powered hub.
    Ciao.

  • New iMac20, strange clicking sound

    Hi,
    I have had my iMac 20" MB324RS/A for about 2 week, and from first day I have strange clicking sound like a clock "tick-tock" with 2-3 sec frequency. There is no dependence between this noise and CPU/HDD/CD load etc.
    I now, somebody have a troubles like this, but only when display sleepeng. My iMac have this clicking every time after "Power On" regardless of OS was loading or not.
    Sorry for my English

    Well... looks like any 5400rpm drive produces such a clicking sound, even though I've never heard it on a 15" PB 1.5 Ghz et al.. The new Hitachi HD isn't as bad as the other one (Toshiba), yet the sound is still very noticeable.
    Guess I got to get used to it. On the Titanium PB, the fan kicks in when charging the battery for about 15 min, so a PB 12" with a clicking HD might not that bad.
    Traded a yet jet engine for a movie projector, he he he.
    The display doesn't look quite as good the TiBook's and it's got a fairly poor viewing angle, yet I knew that already. Besides that, you got to love the 12" PowerBook!!! There's a significant speed increase (1.5 Ghz 1.25 GB Ram, bigger, faster HD vs. 867 Mhz, 768 MB Ram) and - thanks to DesktopManager - the smaller screen is very usable for most tasks. It's much more portable than the 15" and the best of all, all my third party (PowerPC) menu items, preference panes, Latex installation, applications work perfectly. Cloned the TiBook HD and I was up and running within 2 h, thats how long it takes to copy 40GB via FW 400.
    Let Apple roll out some great Intel machines and software developers universalize their apps. In the meantime, I'm carrying around a cute little PB. Buying a PowerPC Mac today is a reasonably choice, if you're like me and need to support a bunch of Macs around you. Software reliability is another key point. Joe Average might be tempted to get a fast Macbook though.
    Who knows, maybe Apple comes up with a 12" PB replacement tomorrow, which is so good, I'll be kicking myself he he he. Wish list: HD screen (without any strange lines, of course), back-lit keyboard, thinner and lighter, Core Duo.

  • Strange clicking sound when screensaver is activated.

    Has anybody noticed a strange clicking sound coming from the right side of the machine when the screensaver is activated? I barely noticed it when I first got the machine, but now it seems to be getting louder.

    i switched to that screeensaver.. maxed the volume and the display
    put my ear up to the keyboard and screen for about a minute
    silence
    ... so it is something with your screen
    there have been a number of inverter problems as mentioned above
    does your scren flicker at low light..
    make noise generally?
    mine is 100% silent...
    but along with the noise if you browse these forums you'll see many people who have had the inverter replaced.....
    sorry i could not be more help.. i would call apple rather than live with it if I were you...
    good luck, sorry i could not be more helpful

  • Mac OS freezes - strange clicking sound from hardrive

    Hey guys,
    I recently had problem with starting my Tiger OS, therefore I decided to reinstall it after few disk checks (the hd appears to be good - at least this is what Disk utility says).
    Of course the installation didnt go smoothly, or the way I imagined it to go, but I eventually managed to install Tiger on my Macbook.
    Now I want to install some software updates, but my macbook freezes everytime I try do something, I can hear a strange clicking, I guess it might be my HD.
    But my Windows partition works completly fine... is it possible that Mac's partition is somehow broken?

    I had an iBook with a hard drive that failed to the point that it would not boot anymore. It would not even allow the installer CD to install a new OS onto it.
    I put the drive in an external enclosure, plugged that into my MacBook, then on the MacBook run a program called Data Rescue II. With that I was able to recover everything that was on the failing iBook HD.
    The reason for the HD failure was bad bearings. the bearing noise was extremely loud by the time all was said and done but Data Rescue II was still able to salvage everything.

  • Encore CS3 crash when i click Build (SWF, BluRay, DVD Burn/Image/Folder) or Check project

    So I'm finally done with my DVD. Now i want this burned to a dvd or make an image file. Each time i hit BUILD or START (Check proj) the program quits and I'm left with the normal OS X message: The application Adobe Encore quit unexpectedly >> Ignore - Report... - Relaunch
    My DVD is not that fancy but i got a menu with 3 buttons made in PS with a pointer highlight and a animating background made in After Effects (using dynamic link) with some music. All of the buttons link to After effects comps with dynamic link. All of the after effects compositions are transcoded and works within the DVD preview (except the DVD menu background wont play, and i got a feeling it will play when i export an image or DVD). And all the After Effects comps links back 2 the menu when done. So there should be no error in the project flowchart.
    My flowchart: http://www3.sqr.no/index.php/get/64a267e640fddd15128d082abb72e3d92a3aedf680aabe20995beb7e e10ae32f
    (small jpg file)
    So i hit build and Encore quits, shut down, finada (Every time!). No matter what out put settings i use. I've exported DVD's from encore before on this computer without problems.
    ---I got this error report---
    Process: Adobe Encore [11321]
    Path: /Applications/Adobe Encore CS3/Adobe Encore CS3.app/Contents/MacOS/Adobe Encore
    Identifier: com.adobe.Encore
    Version: ??? (3.0.2)
    Code Type: X86 (Native)
    Parent Process: launchd [188]
    Date/Time: 2008-08-05 18:36:00.739 +0100
    OS Version: Mac OS X 10.5.4 (9E17)
    Report Version: 6
    Exception Type: EXC_BAD_ACCESS (SIGBUS)
    Exception Codes: KERN_PROTECTION_FAILURE at 0x0000000000000000
    Crashed Thread: 0
    Here is the rest of the error report: (rtf document)
    http://www3.sqr.no/index.php/get/a4568b7ade16f18d2acf09891b81b0bc7c0e4936287eebf2a509470d4 c7098fb
    Don't know if this any help but hope anybody got some ideas. I've been trying to look for a solution on the forums, but without any luck.
    By the way, I'm using a Mac Pro v3,1 (early 2008) with 2 x 2,8ghz quads, 10GB memory, NVIDIA GeForce 8800 GT (512mb) and plenty of disk space.

    Hey, i think if there could be any of the possibilities you talk about, it might have been a naming error. All files i created had the same name in the new project as in the old one. But i used 1 asset arrow that i copy pasted from a library button "Red facets button" and shift pasted on my own buttons as highlight (paste sub picture). In the first project i did not do this as a straight forward thing, a lot of deleting and adding because i had never done it before and there might have happened something with the naming of the arrow i pasted. I used the same arrow in the second project but without messing with delete, paste all the time. But some how there is no problems now, just something wrong with the last project file =S
    Not so important:
    I also noticed while building the new project i once got an "General error", not sure why but happened after a random crash. And 2 get rid of it i had to delete the menu and make it again (i could not edit anything in the menu without getting the error). I rebuild the menu and had another crash when exiting the program, because i thought my computer needs to boot after 2 days online. When i reopened the project i got "General error" in the menu again, but after some clicking it didn't show up (random). Finally i got my project setup and everything works, i did the copy past as sub picture as a straight forward thing.

Maybe you are looking for