Strange colour patches in LR4.1. Possible WB bug?

When looking at some recent images last night i noticed a strange, flesh like halo around some parts of my images.
Ive not noticed it before but its quite worrying. DPP seem to be fine, and if i drag the WB slider to the right it goes away.
Here is a crop off one image to show what i mean
You can see it around the people in the shot, as well as the poles and oil drum,
Dragging the slider to the left shows an even strager effect (ignoring the WB is now off).
Any ideas?

Wrong settings for new color defringe controls.
http://blogs.adobe.com/lightroomjournal/2012/04/new-color-fringe-correction-controls.html

Similar Messages

Colour difference between LR4.4 and CS6

Why is the colour different from LR4 to CS6? Using Spyder to calibrate screen and I know CS6 picks up the Spyder calibration but not sure is LR4 picks up the same calibration. Both are set for srgb colour space.

DdeGannes wrote:
If you wish to have the best match between Lightroom and Photoshop it would be best to select Pro Photo RGB as your Color Working space in Photoshop.
If everything is working as it should (i.e. the monitor profile is good and valid), that normally makes no visual difference on screen. The only possible exception is if the document profile in Photoshop is sRGB and you have a wide gamut monitor. Then you might see gamut differences.
Other than that, the conversion from any color space to the monitor profile should give identical results - that's the whole point of color management. But if there is a problem with the monitor profile, one conversion may go bad but not the other, and so you see a difference.
In short, any difference that is not attributable to gamut clipping (and again that only applies to a wide gamut monitor) is diagnostic of a bad profile.

My macbook pro's screen display has suddenly gone into a strange colour setting where everything appears in a kind of infrared colour palette an I can;t seem to change it back. It's the same for all icon and websites, does anyone know how to restore?

My macbook pro's screen display has suddenly gone into a strange colour setting where everything appears in a kind of infrared colour palette an I can;t seem to change it back. It's the same for all icon and websites, does anyone know how to restore?

Wow! I think I had this same issue just last night.
I was cleaning my macbook pro retina on the outside. Then I opened it up and was wiping dust off the monitor and I can't pinpoint exactly when, but the colors changed suddenly. It looked super strange, it was like green halo's and it looked worse when looking at it at an angle. Of course I took no pictures!!! I was freaking out that my 2 grand laptop was busted and I somehow removed a protective film or something.
But I digress... The image looked very green and spacey, it was almost a neat effect. After about 5 minutes it started to look a little more digital though. There were straight lines of this halo effect on the edges and top. After about 10 minutes it turned into a predominate issue with the blacks on screen. I could open a web browser and it was unnoticable on a white background. After about 15 minutes, you could only barely see the green cloud effect if you looked at the monitor from an extreme angle. After about 20 minutes, it was completely back to normal, I almost feel paranoid like I see a halo or something strange. But I believe that might be all in my head now.
So yerp, lemme know what you guys figure out.

Strange colour spots (red & green) appear after RAW files converted to JPEG, anyone know how to fix it?

Strange colour spots (red&green) appear after RAW files converted to JPEG, anyone know how to fix it? Thanks.

I use "Export" function to convert the picture from RAW format to JPEG format, resolution 240 pixels per inch. Strange red dots appeared in the area supposed to be dark grey, as per the picture below. The red colour does not appeared in the original RAW picture when viewing from Lightroom, only exist in the JPEG it created. Any ideas how to fix this? Thanks!

CS 6...The black in my images is brown. The colour patch in SFW is also brown. help please

CS 6...The black in my images is brown. The colour patch in SFW is also brown. help please

BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, such as total installed RAM, scratch file HDs, video card specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
A screen shot could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Colour Patches on Screen when refreshing or moving to another website on Safari

Hi everyone,
do you have any explanation for why I'm having these colour patches on Safari each time I'm on a web page and decide to either go to another adress or simply click on "show Top sites"
Regards
Darnel Fab

Hi everyone,
do you have any explanation for why I'm having these colour patches on Safari each time I'm on a web page and decide to either go to another adress or simply click on "show Top sites"
Regards
Darnel Fab

[svn] 4610: Commit Josh's patch for 3. x to fix bug SDK-17367 which works around an issue with Dictionary that stops ObjectUtil .toString() working with QNames.

Revision: 4610
Author: [email protected]
Date: 2009-01-21 12:48:01 -0800 (Wed, 21 Jan 2009)
Log Message:
Commit Josh's patch for 3.x to fix bug SDK-17367 which works around an issue with Dictionary that stops ObjectUtil.toString() working with QNames.
QE: Yes, please add a test case to ObjectUtil tests for this scenario.
Doc: No
Checkintests: Pass
Bugs:
SDK-17367 ObjectUtil.toString(QName) causes RTE
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-17367
http://bugs.adobe.com/jira/browse/SDK-17367
Modified Paths:
flex/sdk/branches/3.x/frameworks/projects/framework/src/mx/utils/ObjectUtil.as

VPN-User,
Ok - I see the list of issues and will ensure our X300 specialist takes a look at it.
Please do understand that while you have put together a very coherent list, I try to ensure priority to threads in which multiple customers are focused on a single issue, as we deliver the most benefit to the community in working on those. This forum is primarly a peer to peer discussion forum rather than a Lenovo chat / tech support where we try to solve each and every issue put forth.
Individuals with a long list of issues on a particular machine may find benefit from either contacting technical support and working through their list, or publishing it as you have done and wait for other users of the same system to share their experiences.
Thanks for your patience
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

[svn:fx-3.x] 8019: Applying patch submitted by Daniel Wilday for bug SDK-13855

Revision: 8019
Author:   [email protected]
Date:     2009-06-19 15:50:52 -0700 (Fri, 19 Jun 2009)
Log Message:
Applying patch submitted by Daniel Wilday for bug SDK-13855
Fix: Make sure we re-measure the SwatchPanel after we refresh it.
Doc Notes: None
Bugs: SDK-13855
QE Notes: None
tests: checkintests
Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-13855
    http://bugs.adobe.com/jira/browse/SDK-13855
Modified Paths:
    flex/sdk/branches/3.x/frameworks/projects/framework/src/mx/controls/colorPickerClasses/Sw atchPanel.as

Fuzzy screen, strange colours, and startup freeze

Hello there.
This issue might have been covered, but I have not found a thread with it specifically.
The thing is, I have an first generation Imac G5, with 17 inches screen and 1.8 Ghz. It has Leopard with the latest patches. The serial number was in the range of the repair extention program (http://support.apple.com/kb/HT2390?viewlocale=en_US) so I got it repared for that issue over a year ago. There was no video gliches, but it just refused to power up. They really had a hard time making in work at the shop I went to in Montréal. I think they said the first power supply they instelled grilled, and they also had to change the mother board. But at last it was ok and worked for a year.
But small video glitches (with strange random colour lines)and kernel panics started to became more frequent until finally, the thing froze on mid startup.
After a night's sleep it started all right with a bit of screen oddities but froze two minutes after when a program was started. It starts all right in safe mode, but more screen oddities become apparent over time and after a while it dies painfully in an abstract graphic figures drug addict vision style nightmare. I have tried all the basic reset stuff without sucess.
At apple they say repair it at your own expanse and bugger off... lol. But I'm really being poor student budget here! So basically, I want to identify the problem's origins, know if I can sort it out myself and how... If not, how much would it cost to repair the damned beauty. It would be a shame to end the love-hate relationship we share, and I might be old-school but I like keeping my comps more than 3 years.
Thanks in advance for all your answers ladies, gents and geeks.
Antoine

Welcome to Discussions Antoine - you may be having a problem with your video RAM, or with your power supply or logic board. Try starting from your install disk and run Disk Utility:
Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Let us know what you find,

Strange colours on screen after upgrading memory.

Hi all.
I bought a 2nd hand eMac from eBay and have just received a 512MB SDRAM module to upgrade the memory from it's current 384MB to 768MB.
On the first install I removed my 128MB module and installed the 512 module - No Boot. (beeping on startup)
I thought I'd try the 512MB module on its own - No Boot (again beeps).
I then tried just my 256MB module - Booted fine.
I then tried the 512MB module on its own and it did boot but this time the display colours were very off (the apple logo in Tiger was pink for instance)
Last of all I took out all ram and reseated it all - Success finally.
Now my questions are:
Were the beeps a memory error warning (I assumed they were)?
Is the display issue possibly related to poorly seated memory?
I do have big hands and found it difficult getting the ram in the eMac, especially with the sharp(ish) mesh on the underside of the eMac.
I feel this may be related to me seating the memory poorly but that time it booted with the colours all screwed has me worried in case something more is wrong.
I'm currently testing the memory with Remember and all is fine so far (I'm up to the 256 block sequential test so far)
Thanks for reading and apologies for the long post!

Thanks for the suggestion srojtas.
The eMac has been running fine since posting this and completely passed the Remember memory test. I also tested it by filling the memory up by opening many apps and it didn't crash at all there either.
The eMac didn't come with a hardware CD sadly, so I can't test it that way!
I feel now it must have all been due to me not seating the memory correctly.

Colour disparity between LR4.1 and Elements

Hi all.
I am new to Adobe and the printing of my digital images (using a third party lab).
Pictures I take are in RAW and I only use LR4.1 for post production before exporting images in JPEG and colour space sRGB. I am seeing a visible change on the same monitor between LR4.1 and Adobe Elements 6.0. I should point out the image I like is show in Elements 6.0 or other microsoft (colour managed) application.
Upon having some of the images printed I am seeing a close resemblance to what is in LR4.1 but the B&W images all seem to have this brown tint to them rather than the pure B&W I would expect as shown in Elements or other colour manged application.
On occasions the 'Detail' preview pain also shows the image in the B&W I would expect to see rather than the larger image displayed or that shown under the 'navigator' menu.
I should also point out that on the same monitor (Dell 2208WFP) the colour pictures are near as perfect.
Does anyone have any ideas?
Thank you for your time.
Message was edited by: Danno2013

You have a corrupted monitor profile. You can confirm it using these instructions: http://www.lightroomqueen.com/2008/12/28/corrupted-monitor-profile/ but that's only a temporary fix - you then need to calibrate the monitor properly.

Strange colour cast in LR3 with Canon G11 RAW

Hi all,
I recently bought Lightroom 3 to work with the RAW output from my Canon G11. The majority of the shots want to process are taken underwater around the UK coast. I'm having an issue with colour casts which I hope someone may be able to shed some light on.
With these underwater shots LR3 seems to import them with a very strong green colour cast, even though, when diving, I set the manual white balance at regular intervals. By comparison, Canon DPP imports the RAW files correctly (what I consider correct), and I get the same correct results with Raw Therapee, GIMP and Capture 1. PhotoShop Elements gives the same results as LR3, but I assume they both use ACR 6.1.
I would expect Canon DPP to be correct as it is processing it's own RAW files, but as the other RAW converters match the Canon output, I get the feeling that my problem is with LR3, or possibly ACR. I've scanned both the Adobe LR forum and ACR forum, but can not see any posts where people are having similar issues to me. I did find several post's saying that LR3's support of the Canon G11 was now finished, maybe it has just been tuned for land based shots, not underwater.
I have tried using Adobe DNG Converter, to no avail, and I have also tried all the white balance pre-sets within LR3. Even the custom white balance picker does not give sensible results, it just changes the shots to a slightly different shade of green.
Playing around with other setting in LR3 can make slight improvements, but it's a slow, shot by shot process, and still does not produce a usable finished product, or even a reasonable starting point for fine tuning.
I have found that I can use Canon DPP to output to TIF, which LR3 then opens correctly, but I feel that as I'm not then working with the RAW file, I'm not going to get the best out of LR3's features.
Is there some particular setting within LR3 or ACR that I have missed ? If not, am I actually loosing detail by converting to TIF before opening LR3 ?
I've attached example output from LR3 and DPP. Both use white balance of 'As Shot', and neither have had any processing done on them. The LR3 shot looks lees green that it does in LR3, I assume thats because I've saved it as a low res JPG.
Thanks for any advise people can give.
LR3 output
DPP output

Thanks for that answer, it shows that I may have some settings which need tweaking.
All the LR3 settings are as standard when first loaded, playing with this bunch of shots (about 20 in all) was the first thing I ever tried in it. I wouldn't even know how to apply split toning even if I wanted to (you probably guessed by now that I'm a new user to this software). All the on land shots I've messed around with import correctly, so it's definitly only the underwater ones.
One thing that I've just remembered, may be important, when I select shots to import in to LR3, the thumbnails look fine. It's only when the import process has finished the green colour cast appears. It's almost as if something is being applied right at the last minute.
I haven't tried to white balance the JPEG. I assumed it wouldn't work with the RAW, it would be the same with the JPEG.
I did process some shots using PS Elements a while ago, and don't remember any stong colour casts in that. They were from shallow fresh water rather than deeper salt water, may make a differeence. I believe the ACR plug in with PSE 8 at the time was in the 5.x range. I did manually upgrade the ACR plug in for PSE 8 to 6.1 after loading LR3. I can try backing that out and seeing if I still get the colour cast.
Hmmm, it's looking more and more like a problem with ACR 6.1. At a guess I'd say it's not interpreting the 'as shot' information correctly, or completly ignoring it.
I'll have a go with white balancing the JPEG when I get home. If you can do it, but I can't, it points directly with a setting on my system. I'll also have a look at uploading the RAW file somewhere.
Cheers

Strange colours in iTunes 8

Since upgrading to iTunes 8 my music folder becomes pink and purple every time I click on on a song... very strange
It changes back to normal if I maximise or restor down the window size...
I've tried downloading and reinstalling the program again and it makes no difference.
Is there anything I can do to?

try setting 32 bit colour quality.
Right click in the desktop Properties>>Settings

Strange colour change on other Mac

I have one problem (well, thats why everyone posts here).
I created an Artwork Illustration in Freehand MX that I need
to work on further - on another Mac 200 miles from my home. This
Mac (having more or less the same standard and the same age as my
own, both are from 2004) shows the illustration in weird, almost
glowing, somewhat tacky colours. Only thing is that green is still
green, red still red, only completely different shades of colours.
Whats puzzling is that a tiff created on my home computer of
the same illustration shows the colours almost right on this
computer here. But if I export the illustration as tiff on this
foreign computer its still these strange glowing colours. All other
pictures viewed look right so its no a general false setting of the
computer I´m forced to work here. Also, if I print the
illustration, the colours are close to my own Mac´s showing.
Why is that and what can I do?

> This Mac (having more or less the same standard and the
same age as my own,
> both are from 2004) shows the illustration in weird,
almost glowing, somewhat
> tacky colours.
Check FHMX settings under Preferences > Color > Color
Management. For your
purposes, the settings should be the same on both machines.
Judy Arndt

Strange colour and words distorted

Awrite
I've been getting updates for itunes and it says i'm running the latest version(8.0.1). Don't know if there is something wrong with it and highly doubt there is but the colour behind my songs and any other list i view, also the list where you connect your ipod, the colour is strange too, blocking out words with a gray dark colour. Also the panel on the left hand side with Music, Movies, TV Shows etc going downwards is distorted, not the list but the Heading for it e.g. Library, Store and Playlists are distorted.
Is this something to do with my itunes or something up with the way my computer is displaying things now?
Every other programme i run on my computer is displaying fine, should i maybe download itunes again to see if it fixes the problem?
Cheers to anyone that gives me a wee hand.

See if this helps: : iTunes - Pink iTunes window under iTunes XP/Vista

Strange colour patches in LR4.1. Possible WB bug?

Similar Messages

Maybe you are looking for