Strange e4200 FTP problem

I have an odd problem with the FTP server. I currently hooked up a 250GB portable HDD which is formatted in NTFS. A single folder in the root of the drive is mounted as the FTP server. Every time I upload a zip or far, the file comes out ends up being uploaded corrupt and double the original file size. I have used 2 FTP clients, using either ASCII or binary. No matter how I go about it, I can't make the files upload at the normal file size. Its not just archives, however, I tried an mp3 and it too got uploaded corrupt and double the size. I then downloaded the mp3 to try and play it but it didn't play in windows media player. However I loaded the 'corrupt mp3 into audacity and the file played like normal. I have no idea what to do at this point, aside from returning the device. Having FTP capabilities in my router is very important, so any help would be much appreciated.

You are not alone. I am having problems with the ftp server also. I didn't know whether it was the camera or the disk drives I was trying but you have confirmed that there is a problem. Here are some of my observations:
Bad harddrive formatting: the harddrive connection is not very consistent. I even let the e4200 format the drive itself (to FAT) and that was inconsistent. Sometimes it would see it as useable and sometimes not.
Odd files created: as I was setting up the server with a FAT32 disk, I would get directories of gibberish: very large files with unprintable names.
Corrupted JPEGs: I hooked a DLink network camera into the mix and went with another disk and do get JPEGs from the camera but most of them are corrupt and don't open. The ones that do open are jumbled and have blank places in the images (sort of correlates with your mp3's being slightly useable.
Nice idea for a router, but unfortunately, less than functional.
My configuration:
Camera: DLINK DCS-930L (tried both wired and wireless, ftp both passive and active, tried single transfer and multiple transfers)
Harddrives: selfpowered Seagate FreeAgentGo (250GB, FAT32), Seagate FreeAgent (500GB, NTFS)
CISCO E4200 with latest firmware(v1.02 -- downloaded yesterday)
Computer (shouldn't matter?) Toshiba running XP-tablet.
I hope this helps them troubleshoot this.

Similar Messages

NAS200 Ftp problem

Hi,
I have a little problem with my NAS200. When I try to connect to ftp, I got an error like this:
200 transfer type changed to ascii
227 entering passive mode
Whats wrong ?

Hi gieras. Has this worked before? Have you tried to access it using another computer? Possble reason why you can't access it is Windows firewall settings on your computer. I am not really familiar with the error codes that you mentioned but I've read another post here that may help: https://community.linksys.com/t5/Network-Storage/NAS200-FTP-Problem/td-p/120996

FTP Problems with Dreamweaver 8

The webmaster for the library I work for recently had
difficulty with her computer. She did a system restore from her
discs, and, after that, reinstalled Dreamweaver 8. She sent me an
email to let me know she needed my assistance setting her DW FTP
back up.
While her computer was down I decided to reorganize the
website files. There were dozens of old files and most of the
images and html were scattered throught the main part of the file
tree. She really liked the changes, but, after connecting her to
the site and downloading all the files, a problem arose.
Once she got her laptop back home every time she'd connect to
the FTP she got a group of folders named "Windows, Linux,
Speedtest" and a few others. I contacted our webhost and they told
me this meant she was logging in anonymously. We have our login
name and password in correctly, though, so this shouldn't happen.
No one at our ISP could help me do to them not being familiar with
Dreamweaver.
After playing around with the machine a bit I found that if I
deleted the site from the FTP and re-did it using the same folders
then the first connection was succesful. But, after disconnecting,
the same problem happens again.
I found this article and wondered if it could be causing our
problem.
http://kb.adobe.com/selfservice/viewContent.do?externalId=3491671c
The only thing that makes me think it might not be is the
fact that our login and password stays in the box, but, for some
reason, the FTP is connecting anonymously. Could her doing a
recovery have led to this? Maybe there's an update she needs to
apply that she didn't get after doing the recovery?

It's hard to know what kind of things happened with your
moving stuff around
outside of DW.
Suffice it to say that most FTP problems are router/firewall
related. Does
this help at all?
http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_14834&sliceId=2
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"WesleyThomas" <[email protected]> wrote in
message
news:[email protected]...
> The webmaster for the library I work for recently had
difficulty with her
> computer. She did a system restore from her discs, and,
after that,
> reinstalled
> Dreamweaver 8. She sent me an email to let me know she
needed my
> assistance
> setting her DW FTP back up.
>
> While her computer was down I decided to reorganize the
website files.
> There
> were dozens of old files and most of the images and html
were scattered
> throught the main part of the file tree. She really
liked the changes,
> but,
> after connecting her to the site and downloading all the
files, a problem
> arose.
>
> Once she got her laptop back home every time she'd
connect to the FTP she
> got
> a group of folders named "Windows, Linux, Speedtest" and
a few others. I
> contacted our webhost and they told me this meant she
was logging in
> anonymously. We have our login name and password in
correctly, though, so
> this
> shouldn't happen. No one at our ISP could help me do to
them not being
> familiar
> with Dreamweaver.
>
> After playing around with the machine a bit I found that
if I deleted the
> site
> from the FTP and re-did it using the same folders then
the first
> connection was
> succesful. But, after disconnecting, the same problem
happens again.
>
> I found this article and wondered if it could be causing
our problem.
>
http://kb.adobe.com/selfservice/viewContent.do?externalId=3491671c
>
> The only thing that makes me think it might not be is
the fact that our
> login
> and password stays in the box, but, for some reason, the
FTP is connecting
> anonymously. Could her doing a recovery have led to
this? Maybe there's an
> update she needs to apply that she didn't get after
doing the recovery?
>

I have a strange 3g data problem.

I have a strange 3g data problem. At home I have zero 3G connectivity even though all bars are showing and says "3G" and wifi is "Off" ... unless I am on the phone and then magically the 3G data connection works perfectly!! Does anyone have any idea what is happening? Also when I bring my phone to my dad's or my friends house the problem disappears!! Is this a hardware or a AT&T network problem? os is 4.3.3
Also called ATT and they said there was no problem with the network and that it was a hardware issue. Also restored the phone several times but the problem did not go away.

OK, no trouble shooting. The first thing I'd attempt is restarting in Safe Mode. If you still don't have luck try doing both a SMC and PRAM reset, it wouldn't hurt to do the SMC reset a couple of times. If still no luck let us know.
SMC RESET
Shut down the computer.
Unplug the computer's power cord and all peripherals.
Press and hold the power button for 5 seconds.
Release the power button.
Attach the computers power cable.
Press the power button to turn on the computer.
PRAM RESET
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

E4200 v1- problem creating a shared folder for the FTP server.

Hi,
I'm trying to share an external USB harddrive (4TB- HFS+) that is attached to my e4200 router. I'm trying to set up the FTP server, but when I try to create a shared folder, I get kicked out of the browser based interface for the router just as I'm trying to save the new shared drive. I have tried many different things to get it to work: different computers (PC and Mac) different browsers, reflashing the firmware (which is version 1.0.06, build 3), I tried all of this with an NTFS formatted drive as well- everytime I try to set up the shared folder- right as I hit the save button it kicks me out saying: Session Failure.
I can see my drive on the local network, and I know the FTP server is working, because I can log into it from the outside- but I don't see anything shared, when I do.
I have successfully gotten the media server to work using the same drive- but I can't create shared folder there either... It seems to have shared the entire disk automatically when I first connected the drive to the router.
Anybody have anything else for me to try?
Help!

Same problem. Has anyone found a solution? I contacted tech support and got nonsense responses. I was of course asked to Factory Reset even though I told them I had done it before I called - classic brush off. Basicly here is the problem.
1. I cannot create a share on a USB connected HDD - this worked on the older Firmware. Now every time I try to set up the shared folder- right as I hit the save button it kicks me out saying: Session Failure. I am not the only person with the problem. Crazy thing is I had a share created and it worked after the upgrade. I wanted to add an additional share and now it wont share anything. HDD plugged into my PC works great. I was asked to try a different PC - even though I told them I tried from IE, Chrome, Firefox on a Windows 7, Vista, windows XP, IPad, Kindle and Samsung phone.
2. While troubleshooting with the agent I discovered that although I have remote access disabled in the Administration>Management page but I can still access the router remotely. This is a huge security issue.
3. Linksys is no longer a Cisco Company - if the code is this bad Belkin should take the Cisco logo out of the GUI. Don’t blame Cisco for your poor SW.
I am ready to buy a new router and avoid Linksys and Belkin all together in light of these issues.
Additionally, I would simply downgrade but the older Firmware is not available. When I asked for it I was told I could not get it.

Very strange E4200 Router Connection problems

So Pretty much everything about my router and internet works just fine.
But a week and a half ago, I was suddenly unable to access a website I'd been visiting for years. it's a phpbb forum that's hosted by a friend for a small online community I'm a member of. When I try to access the forum, I get "Could not determine your IP address".
I tried rebooting the network. That didn't work. I put up with it for awhile, but now I am also unable to access another website I frequently use as well, and that error is simply "Oops! Google Chrome could not connect to wowhead.com".
I've tried both websites on multiple browsers and resetting the modem, and router, and clearing my cache and rebooting my computer doesn't seem to work.
Now here's where it gets weird.
I restored my router to factory settings in hope that this might work and it did! For a few minutes I was able to access those websites without a problem, but then my entire intrenet hiccuped hard for a second and now I cannot access them again.
So I reset the router back to default again and it didn't work at all. I couldn't access the websites again at all.
The difference is, the first time arround I disabled the WMM support because my dad likes to stream HBO a lot and it sucks more bandwidth than he needs to do it, so I had it disabled before the first reset(And disabling it did not originally coinside with being unable to access those websites, I disabled the WMM support months and months ago and was able to access those websites just fine for a long time.) WMM is currently active again and after a third reset, the only configurations I have changed are adding a pass word to the wireless connection. (I selected WPA2 Personal encryption, I don't have the CD set up any more, so I opted to activate it the old fashioned way.)
Now the other weird thing, well this looks weird to me at least, is my ping results to google.
http://i41.tinypic.com/5ofbr5.jpg
Now I don't know if they changed something recently, but it didn't used to do that.
Any ways my Firmware is 1.0.05
I hope I've given sufficient information. I'm not sure what else to do at this point except buy a new Router. I've had this one for over a year now. I'd hate to think their 180 dollar router only has a one year shelf life.

Hmm small update
google is telling me my ip address is some strange long string of numbers and letters.
"Your public IP address is 2605:6000:150b:4004:ac96:6419:b590:c635"
This might be why I am unable to access these websites.
also strangely, since I started messing with my network, my IP address has changed? I'm running on Cable, I was pretty sure Cable IP's were static. How bizzare.

Dreamweaver CS3 strange FTP problem

Helllo,
I have just passed from windows to Mac (I got Leopard) .... I
have installed Dreamweaver CS3
and I have imported all the site definition (like Host FTP,
username, password, etc...) from the windows version
But when I try to connect to any server, I recive this error
"An FTP error occured - cannot make connection to host
no response from the server this may be due to one or more
reasons:
- Accessing the server requires firewall settings that aren't
properly set. Please verify that the firewall settings in the Site
category of the Preferences dialog box are properly set, and that
the Use Firewall option in the Site definition dialog box is
selected.
- The server may be accepting only passive mode or only
active mode. Toggling the "Use Passive FTP" checkbox may help you
establish a connection.
- If you are connecting to an IPv6 enabled server, please
select "Use IPv6 transfer mode" checkbox in the Advanced site
definition dialog.
- Your local firewall may be blocking the incoming FTP data.
Please disable it to see if it makes a difference.
- It is possible your FTP may be using a non-standard FTP
port (21). If you need to specify a non-standard port, enter the
port number after host name separated by a colon":". "
I have tryed to use other FTP programs and I got mix results:
Cyber Duck and Fetch are working
Fugu and Filezilla for Mac do not connect to any server
I am clueless .... .... can someone give me a hand?
thanks in advance

Are you running a firewall?
http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_14834&sliceId=2
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"sharemind1" <[email protected]> wrote in
message
news:[email protected]...
> Helllo,
>
> I have just passed from windows to Mac (I got Leopard)
.... I have
> installed
> Dreamweaver CS3
> and I have imported all the site definition (like Host
FTP, username,
> password, etc...) from the windows version
>
> But when I try to connect to any server, I recive this
error :
>
> "An FTP error occured - cannot make connection to host
> no response from the server this may be due to one or
more reasons:
>
> - Accessing the server requires firewall settings that
aren't properly
> set.
> Please verify that the firewall settings in the Site
category of the
> Preferences dialog box are properly set, and that the
Use Firewall option
> in
> the Site definition dialog box is selected.
>
> - The server may be accepting only passive mode or only
active mode.
> Toggling
> the "Use Passive FTP" checkbox may help you establish a
connection.
>
> - If you are connecting to an IPv6 enabled server,
please select "Use IPv6
> transfer mode" checkbox in the Advanced site definition
dialog.
>
> - Your local firewall may be blocking the incoming FTP
data. Please
> disable it
> to see if it makes a difference.
>
> - It is possible your FTP may be using a non-standard
FTP port (21). If
> you
> need to specify a non-standard port, enter the port
number after host name
> separated by a colon":". "
>
>
>
> I have tryed to use other FTP programs and I got mix
results:
>
> Cyber Duck and Fetch are working
>
> Fugu and Filezilla for Mac do not connect to any server
>
> I am clueless .... .... can someone give me a hand?
>
> thanks in advance
>

Dreamweaver CC - FTP problem to access

I´m having some problems to upload files with my Dreamweaver CC.
Every time I try to upload something to the root of my FTP, I get an error message, meanwhile I try to upload to a sub-folder I don`t get any.
You may think that it's a FTP permission issue, but I have check with my provider, made some test and it seems that there is not the problem.
But more strange is that I also have Adobe CS5, and with this one I can upload my files to root without any problem. I have checked both configurations and they are exactly the same (obviously same host, user, pass… etc.).
Do you have any idea where could I have the problem?
Thank you very much for your support

Hi. Is there any progress in solving this problem?
The error message:
The path inside Xcode:
The SDKs for 7.1 and 7.0 were installed/added from the option Xcode> Preferences> Downloads.

Ftp too slow: pharlap and linux ftp problem

Hi all,
my problem seems very strange.
I work with a rt system (PXI 8187 with pharlap os). I have to retrieve several log files that can be very heavy (100 MB or more).
When I retrieve these files using Internet Explorer the ftp has a transfer rate of 500 KB/s ca. If I use SUSE Linux the transfer rate is 10 KB/s, that is not acceptable.
Moreover if I use a windows client onto SUSE Linux (using VMWare) the client present a transfer rate of 500 KB/s.
Finally the SUSE ftp client can retrieve from other FTP server (Linux) with a good transfer rate (1 MB/s).
So I can't understang where is the problem: windows can retrieve from pharlap, linux can retrieve from linux, windows onto linux can retrieve from pharlap, linux CAN'T (because too slow) retrieve from pharlap.
can someone help us?
thanks all.
Andrea

Hi Anmol,
That's an interesting issue, I currently have some cRIO's sitting on my desk and would love to help you get to the bottom of this issue, could you let me know a few things:
1. Operating systems the same?
2. cRIO controller model & revision (revision is the first letter in the part number i.e. 111111C-00L would be rev C)
3. Network speeds of both laptop ethernet ports & the chipsets for these (via device manager)
4. Do you have another PC you could check this on to narrow it down to the laptop
5. Have you always had this issue?
Thanks,
Applications Engineer

FTP problem - FTPEx: No such file

Hello,
I have a file adapter that has been working "normally" for some time. However recently I have discovered some errors with it. The polling of files stops and I get the following error message:
Error: Processing interrupted due to error: FTPEx: No such file.
When I log into the ftp site using another tool like WS_FTP I can see a lot of files in the directory. If I do a rename to the first file in the directory then the polling of files will start again and work normally.
It's a rather strange behavior since the adapter then can work as normal for a week or more before the problem happens again.
If you know anything about why this might occur and how to solve it, please respond.
Thanks,
Per

Thanks for your replies!
The problem has happened with both Per File Transfer and Permanently so I don't think the problem lays there.
About using . (star dot star). There are two different file types in the folder, and they are picked with their own adapter. The problem only happens with one of the adapters and not the other. Today I pick them up like this:
CAL*
DAL*
It's always CAL that goes wrong. I could change it to CAL. if you think that would make a difference. I have also looked at the note mention and will add the timeout to it.
Edited by: Per Rune Weimoth on Sep 23, 2009 12:01 PM
Edited by: Per Rune Weimoth on Sep 23, 2009 12:01 PM

Remote and Testing Server FTP Problems

I have a Dreamweaver site defined. I have an 2 domains and 2
FTP accounts. I am using one for my remote server and one for my
testing server. When I go to preview, it uploads the file to the
remote server instead of the testing server. Then it goes and tries
to view the file on the testing server and there is a file not
found error. If I try the same thing but use 2 network drives or 1
network drive and 1 FTP account (remote or testing), everything
works as expected. Any ideas why this happens?

Sounds like you are properly configured. I don't have a good
idea why this
is not working....
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"supwoman" <[email protected]> wrote in
message
news:fj1jbs$mt8$[email protected]..
>I have one Dreamweaver site defined.
>
> I have one domain (www.1.com) and an FTP account to
upload files to the
> folder
> pointed to by that domain. I am using this information
for my remote
> server as
> part of my Dreamweaver site.
>
> I have another domain defined (www.2.com) and another
FTP account to
> upload
> files to the folder pointed to by this domain. I am
using this information
> for
> my testing server as part of my Dreamweaver site.
>
> The pages I am building are Coldfusion, so I want to be
able to test them
> before deploying them to my live site (www.1.com). I
cannot setup a local
> server to do my testing.
>
> So, I should be able to checkout a file test.cfm, make
some changes, then
> hit
> the server debug button to preview those changes. It
should upload the
> file to
> the testing server and take me to the
www.2.com/test.cfm. Then, when I
> finished
> testing and check in the file it should upload it so it
is found at
> www.1.com/test.cfm.
>
> The problem I have is that when I got to test, it
uploads the file to
> www.1.com/test.cfm instead of www.2.com/test.cfm.
>
> If I use network drives instead of two FTP accounts,
everything works
> fine. I
> hit the server debug button, it transfers the file to
the right place.
>
> Sorry, if I didn't explain that well.
>
>

Dreamweaver 8 FTP problem

Hi,
I have updated from Dreamweaver MX 2004 to Dreamweaver 8.0.2
three days ago. Everything went well with that update.
Dreamweaver 8 has kept my old FTP data so I was able to
connect without problem to my server and work flawlessly with my
files. But today, I thought it could be a good idea to refresh my
FTP data, so I have removed it and build new FTP server data inside
Dreamweaver 8. -- Now I can connect to the server, but I have lost
all my links to my folders, etc. Pictures are not displayed anymore
until I have to write the full path
http://www.etc.etc/etc to relink
to my folders.
Do anybody knows why, without having changing the links into
my site, dreamweaver doesn't recognize the relative path that links
to my folder? FYI, every .html, .js and .css files are placed
inside the same root folder, my pictures are placed in sub folders
in the same root.
Best Regards

> After having installed the FTP part,
> the local preview mode has cut access to almost all my
files???.
Not possible unless you made some mistake. Did you by chance
create a
TESTING server as well? I have seen some people duplicate the
Remote site
settings for the testing server - and that would be a
problem.
> FYI, I had these problems described earlier because I
wanted to work in
> FTP
> Remote without having to install any local site like I
use to do with
> Dreamweaver MX 2004, but I think that Dreamweaver 8 does
not allow this
> approach.
DW8 does allow this approach, but it's a very dangerous mode
to work in -
particularly if you are not too sure about what DW is doing.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"PierreBellefeuille" <[email protected]>
wrote in message
news:[email protected]...
> Hi Nick,
>
> I have solved the problem this way: as I undestand
Dreamweaver 8 workflow,
> I
> had first to defined a local site on my computer HD. I
was able to access
> my
> files without any problem with just the local site
installed. Than I
> returned
> to the ?Manage files? to fill my FTP data. After having
installed the FTP
> part,
> the local preview mode has cut access to almost all my
files???. With the
> Local
> site and the FTP installed, I have used the ?Put? botton
to put back the
> whole
> site from the remote server to the local site on my
computer. Now
> everything
> works perfectly fine. No more problem at all.
>
> FYI, I had these problems described earlier because I
wanted to work in
> FTP
> Remote without having to install any local site like I
use to do with
> Dreamweaver MX 2004, but I think that Dreamweaver 8 does
not allow this
> approach. So we have to have both the local site and the
remote site
> installed.
>
> Thank you again Nick!
>

File to File scenario using Transport Protocol FTP Problem

Hi,
my scenario is a file to file scenario using Transport Protocol FTP
there are 3 systems involved
a. computer 1 ( My system-source)
b. computer 2 (XI server)
c. computer 3 (Target system)
I want XI to pick file from computer 1 and post it to computer 3
I am logging on to XI server from computer 1(thro SAP GUI),
Sender communication channel :
Transport protocol:FTP
Messsage protocol: file
In FTP connection Parameters:
Server: computer 1 IP address
port:21
User name and PW---> I have given computer 1 Username and password.
Connection mode: permanently
Transfer mode: Binary
Folder: C:\ftproot\output
filename : given
In Receiver Communication Channel
Transport protocol:FTP
Message protocol: file
In FTP connection Parameters:
Server: computer 3 IP address
port:21
User name and PW---> I have given computer 3 Username and password.
Connection mode: permanently
Transfer mode: Binary
Put File: Use Temporary File
Folder:
eccserver\saploc\tmp
filename scheme: given
When I activate the scenario file is not getting picked from the source
In Adapter Framework: Message says up and running No message processing now
How to check FTP server is up and running on computer 1 (source system)and Computer 2 (XI server)?
What could be the problem ?
Thanks
dushanth

Hi
Consider that I dont have FTP installed on my computer. According to this blog
/people/shabarish.vijayakumar/blog/2006/08/01/along-came-a-file-adapter-mr-ftp-and-rest-of-the-gang
I have configured.
In sender comm channel I have given Ipaddress of computer 1 (which has a file to be picked)
In Receiver Comm channel I have given IP address of computer 3 (in which file to be posted)
and computer 2 is the XI server
Computer 1 has FTP installed
1. XI server should have FTP installed or not ? IF yes is it FTP client or FTP server or Guild FTP (according to the blog is enough)
2. Computer 3 should have FTP installed or not ?
Please help me I am really confused.
Thanks
dushanth

Dreamweaver 8 on INtel Mac ftp problems????

The basic setup: I have an emac, installed Dreamweaver 8 (actually the entire studio package), it works fine. I want to move our webpage to a new imac (intel). I've copied the files, installed Dreamweaver 8, done the set up for the site.
The problem is: I can't get the FTP connection to work. Whether I'm in the SIte Management section,the TEST part, or trying to connect (with the little electric plug icon), I get this message...a file activity window opens, "An FTP error occured -- Cannot make connection to host. Dreaweaver could not connect because the serve is down or not accepting connections."
Things I've tried: I've explored diligently the Adobe/Dreamweaver website.
I've deleted the Files for Dreamweaver, the web site files from the local host, I've tested the connection using other FTP methods (safari -- a test suggested by Adobe or FEtch); I read some of the posts here after searching for Dreamweaver/Intel items. The server is not down since I've been able to connect an upload from another computer; the computer does perform FTP using other methods...which I suppose I can do...but it makes an extra step.
I"ve tried using Passive FTP or not; I've tried everything I can think of...or suggested by outside sources (adobe, an instructor who teaches Dreamweaver, the Apple forums here); I modified the Hard drive name to eliminate spaces;
I've come to the conclusion it is more an "Apple" issue rather than a Dreamweaver issue.
I'm using the Dreamweaver on an emac and it works flawlessly!! But I need to use the emac for other purposes and set up the website on the Intel imac...
The Question: Any ideas or solutions or something to try????
Thanks for any help, suggestions, ideas. Cathy (working in an elementary school computer lab...)

Yes--I've tried the "test" ftp address suggested by Dreamweaver; I've used fetch to connect as well as upload something.
I've connected to the server from another computer....
Thanks for trying but...the server seems to be functioning okay.

Another strange powerpill error - problem with new aria2? [SOLVED]

Looks like I'm getting another odd powerpill error. Is this a function of the new aria2 package that got deployed a day or two ago?
# powerpill -Syu
:: Synchronizing package databases...
core is up to date
extra is up to date
community is up to date
:: The following packages will be downloaded:
[core]
glib2 openssh
[extra]
alacarte at-spi atk brasero bug-buddy cheese clutter clutter-gtk conky
consolekit dasher deskbar-applet devicekit-disks devicekit-power eggdbus
ekiga eog epiphany evince evolution-data-server evolution-exchange
evolution-webcal file-roller gcalctool gconf gconf-editor gdm gedit glibmm
gmime gnome-applets gnome-backgrounds gnome-control-center gnome-desktop
gnome-desktop-sharp gnome-disk-utility gnome-doc-utils gnome-games
gnome-games-extra-data gnome-icon-theme gnome-keyring gnome-mag gnome-media
gnome-menus gnome-netstatus gnome-nettool gnome-panel gnome-power-manager
gnome-python gnome-python-desktop gnome-screensaver gnome-session
gnome-settings-daemon gnome-system-monitor gnome-terminal gnome-themes
gnome-utils gnome-vfs gnome2-user-docs gok gtk-engines gtk-sharp-2 gtk-vnc
gtk2 gtkhtml gtkmm gtksourceview2 gucharmap gvfs hamster-applet kdelibs
libatasmart libbonobo libbonoboui libgdata libgnome libgnomekbd libgnomeui
libgphoto2 libgtop libgweather libsigc++2.0 libsoup libsoup-gnome libunique
libwebkit libwnck libxklavier metacity mousetweaks nautilus opal orca pango
pangomm polkit polkit-gnome poppler poppler-glib ptlib pygobject pygtk
pygtksourceview2 seahorse seahorse-plugins sound-juicer tomboy totem
totem-plparser vinagre vino vte yelp zenity
[community]
perl-xyne-arch
:: Number of Packages: 117
:: Total Download Size: 298.48 MiB
:: Total Installed Size: 1015.32 MiB
:: Proceed with download? [Y/n] y
/usr/bin/aria2c: unrecognized option '--retry-wait=2'
Exception: [OptionParser.cc:149] Failed to parse command-line options.
aria2: Usage: aria2c [OPTIONS] [URL | TORRENT_FILE | METALINK_FILE]...
aria2: Printing options tagged with '#help'.
aria2: See -h option to know other command-line options(#basic, #advanced, #http, #https, #ftp, #metalink, #bittorrent, #cookie, #hook, #file, #xml-rpc, #experimental, #help, #all).
aria2: Options:
aria2: -h, --help[=TAG|KEYWORD] Print usage and exit.
aria2: The help messages are classified with tags. A tag
aria2: starts with "#". For example, type "--help=#http"
aria2: to get the usage for the options tagged with
aria2: "#http". If non-tag word is given, print the usage
aria2: for the options whose name includes that word.
aria2: Possible Values: #basic, #advanced, #http, #https, #ftp, #metalink, #bittorrent, #cookie, #hook, #file, #xml-rpc, #experimental, #help, #all
aria2: Default: #basic
aria2: Tags: #basic,#help
aria2: Refer to man page for more information.
--> All downloads have finished successfully
:: Starting full system upgrade...
resolving dependencies...
looking for inter-conflicts...
Targets (118): glib2-2.22.2-1 pygobject-2.20.0-1 pygtk-2.16.0-1 gnome-menus-2.28.0.1-1 atk-1.28.0-1
pango-1.26.0-1 gtk2-2.18.2-1 eggdbus-0.5-1 polkit-0.94-1 gconf-2.28.0-1
libbonobo-2.24.2-1 gnome-vfs-2.24.2-1 libgnome-2.28.0-1 libbonoboui-2.24.2-1
gnome-keyring-2.28.0-1 libgnomeui-2.24.2-1 gnome-python-2.28.0-1 libsoup-2.28.0-1
libsoup-gnome-2.28.0-1 libgweather-2.28.0-1 evolution-data-server-2.28.0-1
gnome-desktop-2.28.0-1 libwnck-2.28.0-1 gnome-panel-2.28.0-1 alacarte-0.12.4-2
at-spi-1.28.0-1 gmime-2.4.10-1 totem-plparser-2.28.1-1 libunique-1.1.2-1
brasero-2.28.1-2 libgtop-2.28.0-1 bug-buddy-2.28.0-1 gnome-icon-theme-2.28.0-1
cheese-2.28.0.1-1 conky-1.7.2-2 consolekit-0.3.1-1 dasher-4.10.1-2
gnome-python-desktop-2.28.0-1 deskbar-applet-2.28.0-1 devicekit-power-010-1
ptlib-2.6.5-1 opal-3.6.6-1 libsigc++2.0-2.2.4.2-1 ekiga-3.2.6-1 eog-2.28.0-1
libwebkit-1.1.15.1-1 epiphany-2.28.0-1 poppler-0.12.0-1 poppler-glib-0.12.0-1
evince-2.28.0-1 libgphoto2-2.4.6-3 sg3_utils-1.27-2 libatasmart-0.14-1
devicekit-disks-007-1 gnome-disk-utility-2.28.0-1 gvfs-1.4.0-1
evolution-exchange-2.28.0-1 evolution-webcal-2.28.0-1 file-roller-2.28.0-1
gcalctool-5.28.0-1 gconf-editor-2.28.0-1 libxklavier-4.0-1 polkit-gnome-0.94-1
gnome-session-2.28.0-1 gdm-2.28.0-1 gtksourceview2-2.8.1-1 pygtksourceview2-2.8.0-1
gedit-2.28.0-1 glibmm-2.22.1-1 gucharmap-2.28.0-1 libgnomekbd-2.28.0-1
gnome-applets-2.28.0-1 gnome-backgrounds-2.28.0-1 zenity-2.28.0-1 metacity-2.28.0-2
gnome-settings-daemon-2.28.0-1 gnome-control-center-2.28.0-1 gtkhtml-3.28.0-2
vte-0.22.2-1 gnome-desktop-sharp-2.26.0-2 gnome-doc-utils-0.18.0-1 clutter-1.0.4-1
clutter-gtk-0.10.2-1 gnome-games-2.28.0-1 gnome-games-extra-data-2.28.0-1
gnome-mag-0.15.9-1 gnome-media-2.28.1-1 gnome-netstatus-2.28.0-1
gnome-nettool-2.28.0-1 gnome-power-manager-2.28.0-1 gnome-screensaver-2.28.0-1
pangomm-2.26.0-1 gtkmm-2.18.2-1 gnome-system-monitor-2.28.0-1 gnome-terminal-2.28.0-1
gtk-engines-2.18.4-1 gnome-themes-2.28.0-1 gnome-utils-2.28.0-1 yelp-2.28.0-1
gnome2-user-docs-2.28.0-1 gok-2.28.0-1 gtk-sharp-2-2.12.9-1 gtk-vnc-0.3.9-1
hamster-applet-2.28.0-1 kdelibs-4.3.2-4 mousetweaks-2.28.0-1 nautilus-2.28.0-1
openssh-5.3p1-1 orca-2.28.0-1 perl-xyne-arch-0.82-2 seahorse-2.28.0-1
seahorse-plugins-2.28.0-1 sound-juicer-2.28.0-1 tomboy-1.0.0-1 libgdata-0.4.0-1
totem-2.28.1-1 vinagre-2.28.0.1-1 vino-2.28.0-1
Total Download Size: 298.48 MB
Total Installed Size: 1017.04 MB
Proceed with installation? [Y/n] y
:: Retrieving packages from core...
glib2-2.22.2-1-x86_64 2.8M 718.0K/s 00:00:04 [##############################################] 100%
openssh-5.3p1-1-x86_64 849.0K 399.5K/s 00:00:02 [##############################################] 100%
:: Retrieving packages from extra...
pygobject-2.20.0-1-... 551.4K 207.3K/s 00:00:03 [##############################################] 100%
^Cygtk-2.16.0-1-x86_64 894.7K 370.1K/s 00:00:04 [################------------------------------] 35%
Interrupt signal received
Last edited by graysky (2009-10-12 20:55:38)

If you're going to use powerpill you should probably subscribe to the following thread:
http://bbs.archlinux.org/viewtopic.php?id=56583
Your answer is on the very last page, but in summary the problem is that the --retry-wait option is no longer supported in aria2 which you can see in the code you pasted.
/usr/bin/aria2c: unrecognized option '--retry-wait=2'
Xyne has already updated the code so you can either get the code from his site or wait for the mirrors to sync.

Strange e4200 FTP problem

Similar Messages

Maybe you are looking for