Strange FCIP Issue (# of connections)

Is anyone aware of the number of FCIP connections you can have on an MDS9513 with
Sup (Gen2) 3.2(2c)
14+2 (Gen1) 3.2(2c)
18+4 (Gen2) 3.2(2c)
We are in the process of replacing the 14+2 with the 18+4 - However it would seem I have encountered a strange restriction/failure when I come to configure the 18+4 GigE ports with the 14+2 GigE ports still configured (FCIP profiles, Tunnels etc) and Linecard installed (though admin down)
Though we have managed to configure at least 1 GigE Port on the 18+4 linecard, the issue is when trying to configure an additional FCIP channel on the 18+4. One side of the physical direct connected Pairing indicates as up and operational ie (GigE 5/1 to GigE 5/1). Its PEER FAILS to become Operational (Up) and continues to maintain in an Initialisation state and thus preventing a Tunnel to be created regardless of which GigE port is used. The following as been investigated:
•Change SFP - Fault still apparent
•Change Cable - Fault still apparent
•Change GigE Port pairing (ie 5/4<-->5/4) - Fault still apparent
•Investigate/Debug FCIP Profile for mis-configuration (ie PEER IP, passive mode, listening Port etc) - No mis-configuration found between pairing
•Investigate/Debug FCIP Interface for mis-configuration (ie PEER IP etc) - No mis-configuration found between pairing
•Licensing Checked - SAN_EXTN_OVER_IP_18_4 - Installed and in use on all switches
Since we have a dual Fabric Design - Fabric B exhibited the same symptoms with no additional configuration having been applied (ie no additional FCIP tunnels created), would seem to indicate at this moment in time that it maybe its a Gen1/Gen2 and/or Licensing issue.
The only thing left is to actually remove the 14+2 linecard.
Any thoughts?

Thanks Vijay for respond..
I am not using any transformation or Mapping. I configured a DB Adapter first. Then make a BPEL Process having input and output according to DB Adapter XSD file. then i just invoked and copied the output of procedure to output of payload.
Thanks
Nasir

Similar Messages

  • Strange performance issue with 3510/3511 SAM-FS disk cache

    Hi there!
    I'm running a small SAM-QFS environment and have some strange performance issue on the disk storage part, which somebody here might be able to explain.
    Configuration: one 3510, dual controller, RAID-5 9+1, one hot spare and one disk not configured for whatever reason. The R5 logical drive hosts a 150GB LUN for SAM-QFS metadata (mm in SAM-FS speak) and a 1TB LUN for data (mr in SAM-FS speak). Further, there are two small LUNs (2GB, 100GB) for some other purpose. Those two LUNs have nearly no I/O. All disks are SUN146G. Host connection is 2GBit, multipathing enabled and working.
    Then the disk cache became too small, and the customer added a 3511 expansion unit with SUN300G disks. One logical drive is a RAID-1, 1+1, used for NetBackup catalog. The other is a RAID-5, 8+1, providing two LUNs: 260GB SAM-FS metadata (mm) and 1.999TB SAM-FS data (mr).
    For SAM-FS, the LUNs form two file systems: one "residing" in the 3510, the other "residing" in the 3511 expansion. Cabling is according to the manual and checked several times by several independant people. Operating system is Solaris 10, hardware is a V880.
    The problem we observe: SAM-FS I/O on LUNs on disks inside the 3510 is fine. With iostat, I see 100MB/s read and 50MB/s write at the same time. On the SAM-FS file system which is running on the two LUNs in the 3511, the limit seems to be at 40MB/s read/write. Both SAM-FS file systems are configured the same in regards of block size.
    In case I have activity on both SAM-FS file systems, I see 100MB/s+ on the LUN running inside the controller shelf and another 40MB/s on the disk runnin in the 3511 expansion chassis. So, the controller is easily capable of handling 150MB/s.
    Cache settings in the 3510 controller are default I think (wasn't installed by me), batteries are fine.
    Is this 40MB/s we experience a limitation by the expansion shelf? Don't think so. Anybody has any ideas on this? What parameters to check or to change? Any hint appreciated. I can also provide further details if needed. Thank you.
    wolfgang

    SUN300G disks sound like 300GB FC disks.
    Depending on how many files are in the SAMFS file system, sharing the mm and mr devices on the same RAID array can be a pretty horrible idea. In my opinion and experience, it's almost always better to NEVER put more than one LUN on a RAID array. Period. Putting more than one LUN on an array results in IO contention on that array. And large, unnaturally configured (9+1? Why?) RAID arrays will have problems from the start.
    What are the block sizes used on the RAID arrays? It wouldn't surprise me to see that the RAID array on the expansion tray has a very large block size. Larger block sizes are, in general, not better. Especially for SAMFS metadata - which IIRC is something like 8k or 16k blocks.
    I suspect what is happening is most of the metadata updates are going to the mm device on the new array, contending with the IO operations on the file data.
    How much space is left on each mm device? What does "iostat -sndxz 2" show when you're having the IO problems?

  • HP Dm1-1102sa Strange charging issue

    Hi,
    My laptop (HP dm1-1102sa) has developed a strange charging issue. The laptop will initially charge fine then it will flick between being charging and running on battery constantly. I bought another battery to see if it was that but the problem still occurred. I then took it apart to check for loose connections and voltage. There were no loose connections and the pins on the battery terminals were showing a constant 18.5v. I tried running the laptop with out the battery and the laptop shutdown after a while.
    Anyone have any ideas on what I can do next?
    Thanks in advance.
    Simon

    Hi, thanks for the response, I had a look at this page and followed the suggestions, it all came up fine.
    What I have noticed is the bi-coloured LED that sits next to the power connection on the left side was white which indicates not charging (so it seems) , even when it was at 73% and plugged in it wasn't charging, I removed the battery and gently blew out the plug and socket and re-connected the battery several times to see if it was a contact issue, I also did the same for the power connector.
    The odd thing was it would run perfectly on battery and on mains just not charging.
    I downloaded the latest bios revision (not yet installed), so I left it for a while with the battery and the mains lead disconnected, reconnected everything and noticed the bi-coloured LED was now orange so I left it on the desk for a while not running and when I did start it up some time later it was upto 95% charge and then stopped charging again, and again the LED was back to whte.
    Today after receiving this message I tried the suggestions as per the document (except I pulgged in the mains first which brought up the orange LED), performed the tests, I had already tried the HP assistant battery test in windows which showed no issues (still wasn't charging, sitting at 73%), now with it running in front of me (not the computer I am using to type this response) the LED is still orange and the message I get now is "99% available (plugged in, charging)".
    So for the moment it appears to have righted its self which is a concern, I hope that it stays this way....
    JJ

  • HT1695 Hey, guys! I connected to the wi-fi by my iPhone (5) for 3 weeks. Now my iPhone doesn't connect to the network anymore. And I can't understand why. Will you please help me? It's strange,cause tonight I connected frequently. But now I can't! :(

    Hey, guys! I connected to the wi-fi by my iPhone (5) for 3 weeks. Now my iPhone doesn't connect to the network anymore. And I can't understand why. Will you please help me? It's strange,cause tonight I connected frequently. But now I can't! :(

    Hello LNIN5,
    Thank you for using Apple Support Communities!
    I have a couple resources for you to help troubleshooting wifi connection issues with an iOS device.
    The first is named iOS: Troubleshooting Wi-Fi networks and connections and can be found here http://support.apple.com/kb/ts1398.
    Take care,
    Sterling

  • Strange power issues

    I am having some strange power issues with my six week old Macbook. The symptoms are as follows (I apologise in advance for the length of this post) :
    1) If the battery charge is below 50%, and you connect the magsafe charger prior to power-on, the charge light will illuminate until the grey boot screen comes up. Then the charge light turns of completely & the Macbook boots up using battery power. If I disconnect the magsafe connector, followed by the mains and reconnect in the reverse sequence, the light turns green momentarily and then orange (as it should for charging)
    2) If I start the coconutBattery application after booting into OSX, while the charge is still below 50%, the same issue occurs again with the magsafe. It appears to happen at the exact time the application queries the battery. I can get the charger working if I follow the same disconnect/mains/reconnect sequence.
    3) The issues above also seems to occur when the battery updater checks the battery. The Macbook does not recognise that the charger is plugged in.
    4) If the charge is above 50%, then all works as expected. The coconutBattery application does not affect the charger. The Macbook works as normal.
    I have tested with a brand new magsafe & a new battery - symptoms are identical. I have noticed several other non-consistent issues - the flashing green light/orange light on the magsafe connection, unusual battery life calculations (70+ hours).
    I have performed calibrations & reset the PMU and the PRAM, and have all current updates. And I have spent a large amount of time in the forums looking at similar issues without much success. I am beginning to suspect the logic board (DC chip) is at fault, however I dont relish the idea of dropping my new Macbook at my local Apple Repair centre & getting it back three weeks later with the same issue.
    My current cycles (on this new battery) are at 2 with a full charge capacity of 5142 mAh.
    My questions to the community are:
    Does anyone have a similar experience with these types of symptoms?
    Or can someone illustrate on what would cause the Macbook to believe that the magsafe was disconnected? Whatever internal system call the coconutBattery application uses to recover details from the battery appears to trigger this behavior.
    I would appreciate any thoughts on this one.
    Macbook Core 2 Duo - 2GB RAM   Mac OS X (10.4.9)  

    Just another observation, based on reading some of Apple's documentation regarding the AC charger:
    "If the adapter works after this 60-second "rest," you most likely have a line noise issue with your power source that will require you to reset the adapter (by repeating this moment of rest) periodically. This happens when the AC adapter's over voltage protection feature senses ground noise and then turns off the adapter."
    Could a sudden draw of power required at a 50% and below charge trip this over voltage protection feature? I know the charging draw varies based on current battery level.
    I have tested this in UPS protected boards with the same result.

  • HT4628 My macbook pro doesn't connect to the Wi-Fi at home while my iPad connects to the same Wi-Fi. When I try connecting my macbook to my iPhone's personal hotspot, the internet works but the issue is connecting my macbook to the Wi-Fi. Please help!!

    My macbook doesn't connect to the Wi-Fi at home while my iPad connects to the same Wi-Fi. When I try connecting my macbook to my iPhone's personal hotspot, the internet works but the issue is connecting my macbook to the Wi-Fi. Please help!!
    I don't understand how to fix this and I don't seem to understand where the problem is coming from.

    Let's try the simple approach first. Restart your router. Any change?

  • 10.9.2 Update Issue (VPN) - Eclipse Perl debugger issues while connected to VPN

    This post was initially added to this discussion: 10.9.2 Mavericks update issues
    I have yet another issue related to 10.9.2 update - Eclipse Perl debugger issues while connected to VPN...
    One of the big changes introduced by 10.9.2 update - are VPN changes (security fixes). Unfortunately, whatever these changes are - they "broke" Eclipse (OpenSource IDE) debugger. I am not sure if *all* programming languages (Eclipse plugins) are affected by this, but I know for sure that 'Epic' (Perl plugin) debugger *stopped working* while system is connected through VPN.
    Here is the error that gets “popped-up” in the Eclipse:
    Timed out while waiting for Perl debugger connection
    … and here is exact exception stack that gets printed:
    Unable to connect to remote host: 130.10.210.74:5000
    Compilation failed in require.
    at /Users/valeriy/workspace/ROBO-PROD-RA-685/src/lib/test/Val_test.pm line 0.
              main::BEGIN() called at /Users/valeriy/workspace/.metadata/.plugins/org.epic.debug/perl5db.pl line 0
              eval {...} called at /Users/valeriy/workspace/.metadata/.plugins/org.epic.debug/perl5db.pl line 0
    BEGIN failed--compilation aborted.
    at /Users/valeriy/workspace/ROBO-PROD-RA-685/src/lib/test/Val_test.pm line 0.
    Can't use an undefined value as a symbol reference at /Users/valeriy/workspace/.metadata/.plugins/org.epic.debug/perl5db.pl line 7596.
    END failed--call queue aborted.
    at /Users/valeriy/workspace/ROBO-PROD-RA-685/src/lib/test/Val_test.pm line 0.
    (of course IP address changes dynamically for each VPN connection session)…
    I was able to prove that this issue is related to 10.9.2 update:
    Issue *does not* exist under 10.9.1 (I had to revert back to 10.9.1 to get it working again)
    No updates were performed around the same time 10.9.2 update occurred (I verified that using Software Update log)
    No configuration changes were introduced around the same time
    Reverting back to 10.9.1 using Time Machine (thanks god I had backup !!!) fixed the issue
    Steps to reproduce this issue:
    In Eclipse, try to use 'Epic' (Perl plugin) to debug any perl script while *not* connected through VPNEpic debugger works
    Connect to VPN
    Start Epic debugger to debug same script
    Debugger *does not* start, and "Timed out while waiting for Perl debugger connection" error pop-up comes up after some time. At the same time, exception stack (listed above) is printed in Eclipse's console
    I am programmer/software developer, I work remotely (telecommute) and thus have to rely on use of VPN to connect to company's intranet. Perl - is primary language used by my team, and we use Eclipse IDE with Epic plugin - heavily. Use of Epic's debugger - is a *very large* aspect of my work, I cannot work without it. So in essense, 10.9.2 has *entirely* disrupted my ability to work! It took me almost a week to get back to normal work environment, and I cannot afford to let it happen again... I need Apple's development team resolve this VPN related issue, as soon as possible! Because of this issue, I am *stuck* with 10.9.1 and can not upgrade my laptop to any other versions. In fact, I had to disable system updates - just so I do not run into this issue again... I contacted Apple's Tech Support on 02/28 with this issue (Ref: 582428110), asking to raise trouble ticket. Since then, I tried to follow-up on that issue, but do not get any information. Please advise on the status:
    is there a trouble ticket to track this issue?
    is there any progress?
    what's the ETA for an update that fixes this problem?
    - Val
    Message was edited by: vpogrebi

    Am I the only one experiencing this issue ???

  • Strange import issue .. no longer works in 2.6 or Beta 3

    Strange import issue.
    I use LR-2.6 everyday but have only played around with the LR-3 for a limited amount of time so the other day I decided check it out and tried to import a handful of RAW(canon) files on a SDxc-8g card via a USB card reader. I set it up to copy and convert to DNG, apply a few keywords and Metadata but when I tried it acted like it imported the first image and then froze. Card reader lights stopped blinking and just stayed on, program task bar doesn’t show any progress, not even for the first image. I then went to the folder that I was going to have the images copies to and it contained a file of the first image, but there is no indication that LR-3 even created it and it doesn’t show up in the catalog. When I tried to close out LR-3 is popped up the “in the middle of a task warning” so I just closed the program and tried it a couple more times to no avail.
    So I though o well I will just open up LR-2.6 and import them from there, guess what now LR-2.6 does the exact same thing!!
    I thought maybe my card reader was a POS but I was able to drag all the files to a new folder on my desktop and import them from there, nope. Tried rebooting a couple times, even opened a new catalog to test with, in both LR-2.6 and LR-3 and neither will work..
    I am stumped any ideas?

    Thank you for everyone's assistance
    I actually figured out what the problem was, like most issues it comes back to operator error, it seem I had inadvertently chose a "rename file on import" template that I had set up to name the files based on a custom fill-in field in the Meta Data, I normally only used that template when I was exporting images that had been completely edited, so being these images were new imports that field was blank, hence it would import the first image and then do to " don't import subjected duplicates" being checked it would just stop the import process.

  • Does anyone has issue to connect to the wi fi at home

    I just got my ipad2 and try to coneect to my home wi fi, and got issue to connect to the wi fi net work. I had typed in my password coupe time, but no connection at all. I am sure my password is correct, what else should I check for this issue? Anyone knows this?

    No problem for me.  I also have the wifi &amp; 3G iPad2
    Suggest you call your isp provider to be sure your router works with your ipad, and verify your log in name and password. Also, remember to use capital letters when necessary, if that's how your login was set up.

  • I've been having an issue of connecting to wifi. I have restored and set up my phone as a new one and i still can't connect. Also i have restored my network setting also. The wifi button is still grey and i cant switch it on or off.

    I've been having an issue of connecting to wifi. I have restored and set up my phone as a new one and i still can't connect. Also i have restored my network setting also. The wifi button is still grey and i cant switch it on or off.

    Hi _Pchay,
    Accordign to the artcle below, it looks like you have done all the troubleshooting steps and your next step may be to contact Apple Support. 
    iOS: Wi-Fi settings grayed out or dim
    -Griff W. 

  • MDP to HDMI adapter causing issues while connecting Macbook air late 2013 edition to Projector. Projector shows grains on the display.

    MDP to HDMI adapter causing issues while connecting Macbook air late 2013 edition to Projector. Projector shows grains on the display.

    Sounds like you may have been in extended display mode. If so, all you had to do was drag a window to the projector display. Or, if you wanted mirrored mode, in display preferences select check mirror display.

  • Issue while connecting to MS SQL Server 2008

    Hi everyone,
    I have not seen any thread that gives me a clue to my problem.
    I have OBIEE 10.1.3.4.0 on Windows.
    I have created an ODBC3.5 Datasource to a SQL Server 2008 and the test connection is successful.
    I have also imported the tables from the SQL Server 2008 into the Physical Layer of the OBIEE Administration tool. However after check-in, my problem begins trying to do an Update Row Count with the following Error message:
    NQODBCSQL_STATE: HY000nQSError: 10058 A general error has occurred.
    nQSError: 43093 An error occured while processingthe EXECUTE PHYSICAL statement.
    nQSError: 16023 The ODBC function has returned an error. The database may not be available, or the network may be down.
    Any suggestion or pointer will be greatly appreciated.

    Reading your post Issue in connecting to MS SQL Server 2008 I guess this thread here can be closed.
    Cheers,
    C.

  • So, about a week ago my macbook pro started having lots of issues: wifi connectivity, slow performance, sound issues, spotlight wasn't working. After going through the issues with apple support, they decided the best course of action was to erase it...

    So, about a week ago my macbook pro started having lots of issues: wifi connectivity, slow performance, sound issues, spotlight wasn't working. After going through the issues with apple support, they decided the best course of action was to erase the hard drive and do a reinstall. Since I have a recent backup this seemed like a good enough option. They were kind enough to send me a copy of the snow leopard disk to do the install since we couldn't get it to complete through the disk utility. Not sure why, since it says we are fully connected, it just never completed.
    Anyway, so now that you have the background here is the new issue. The macbook pro keeps spitting out the disk I'm trying to install from. Disk utility and using the 'Startup Disk' function from the apple menu doesn't read the disk.
    Can anyone suggest a solution to this vexing problem?
    Thanks in advance.

    Jeremy.Laurin,
    have you tried agb76’s approach here?

  • Issue while connecting from Biztalk adapter to SAP ECC 6.0

    Hi Friends
    Issue while connecting from Visulal Studio 2005 to SAP ECC 6.0 throgh Biztalk adapter2.0, even if we pass the correct login details, system is throwing an error like incorrect user/password.
    Can you please tell anybody the solution for this.
    Regards
    Praveen

    HI,
    is there a special "formation" to put in the user / pass ?
    maybe a missing domain ? or missing values like "/" or "\" ?
    Do you getting this error in the Biztalk Monitor (Visual 2005) ?

  • I'm having issues with connecting my iPhone 4 to iTunes?

    Here's some information:
    Apple product: iPhone 4
    Computer: Windows 8 (originally) to Windows 8.1 (upgraded version)
    Okay, I'm having issues with connecting my iPhone 4 to iTunes. I've connected it via U.S.B. and now everything's not working right the 10th time. Am I to redownload the iTunes software once again or will I never be able to add music anymore?

    OffTime wrote:
    What do you mean with logging?
    Hans
    Close any open applications.
    Click the Apple icon top left of the screen.
    Select the bottom option in the cascading menu: Log Out (your user name).
    Log in a Guest.
    This will dertermine if there is a problem with your Admin account.
    Al

Maybe you are looking for

  • Getting a bad bind variable error while compiling a custom form in R12

    Hi, I am getting a bad bind variable error while compiling a custom form. I tried setting the forms_path variable and I am still getting the error. Can anyone please suggest what can be done? DECLARE BEGIN IF :parameter.p_line_ship_to = 'T' THEN IF :

  • Problm on selection screen

    1) I have one selection screen field which is meant for only display what will i do? 2) if i run bpth bdc,call transaction in different sessions i got the message 'successful' wat does mean? 3) how do u test a sap-script? 4) wat is standard text? use

  • Reg : Table control row settings to change mode

    Hi geeks.         I am working on a requirement where the table control has to be in display mode at the time of prepopulating(initial display).This works fine and could get all columns in display mode for which i used column properties of table cont

  • Business Connectors

    Can someone tell me how to detect the requirement of BPM on the Business Connector developer side among the flow services. How to detect if there exists BPM in the package at BC developer or not? thanx

  • Master Templates in FCP all gone Black

    The Master Templates (under Effects) in my FCP have all gone Black. But everything else under Effects are ok. What happened and how to I revive the Master Templates?