Strange Issue With QIP 7100 STB and Sony Bravia TV

I am having a strange issue with a 27" Sony Bravia Television connected to a Motorola QIP 7100 HD STB.When viewing a non HD channel the television input number display, resolution display, picture mode display and clock come on and off every few seconds. The issue stops when I tune in to an HD channel. If I return to a non HD channel the issue reappears. I am new to FIOS from Directv where I did not experience this. The television is connected to the STB via HDMI. Everything else seems fine except for picture stuttering that I am getting on all of televisions but I'll save that issue for a separate thread. I tried removing the TV remote to no avail and changing the batteries in both the FIOS and TV remote with no success either. This is a very annoying issue and I feel that it must be caused by the STB. I was wondering if anyone experienced anything similar to this and if they were able to correct the issue. I would greatly appreciate any assistance. Thank you and Happy New Year.

It is possible that your Sony doesn't support the mode the STB is set to for SD (some HDMI TV inputs don't support all formats that the STB can output).
Have you tried going to the STB settings menu and under Video Settings played with the various options for 4:3 override? This setting controls the STB output for SD and lets you set 480i, 480p, and OFF (also STRETCH at least on some firmware version). In the OFF setting the STB upconverts your SD to whatever the HD resolution is set for - 1080i or 720p.
Hope that solves your issue.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Similar Messages

Premiere Pro CS5.5 -very strange issue with the color tones and Preview-

I deal with a very strange and not usual problem in Premiere Pro CS5.5 (also the version CS5). What I try to do is just a simple color correction. The problem occurs when I try to use Three Way Color Corrector but it happens with Fast Color Corrector also.
When applying the Three-Way Color Correction and without changing anything else (just applying), can be seen in the preview of the soft how sudden changes in color tones. For example, the gray tone becomes a little more green, but also can be seen very easy a change in the other color tones too. In fact even RGB Parade show the same thing. This is very, very strange and unacceptable and saw that it happens when trying to use Colorista II too.
I tried the same thing in Sony Vegas Pro 11 and I downloaded the trial version of Edius 6 to convince me if the same thing happens. Not! In Sony Vegas and Edius everything is working correctly, I have not experienced these problems in the preview's of this 2 others softs.
This issue is very annoying because every possible color correction is based on what we see in the preview and if in this preview the tones are seen altered realize that can not make a decent color correction. So what happens here?!? I uploaded a small video demonstration to see very clearly about what I'm talking. You can see in the next link: http://vimeo.com/35317616

Yes Jim, you're right. No changes in the scopes when one just apply RGB Curves, Fast Color Corrector, RGB Color Corrector or the Three way Color Corrector (last three thanks to the new update 6.03). I already wrote that Adobe team has been able to fix this bug for some of the tools/effects.
But Brightness&Contrast? Change Color? Color Balance? Levels? MBLooks? Twixtor? Colorista II? Does it seem normally that all scopes or just one of them jump when you just apply one of these effects/tools? Not to say that in some situations even the tones change (especially in shadows&midtones).
You say this is something "very minimal". I say it is not so. I don't find normally to make a very detalied CC with Three way Color Corrector and then when applying Colorista/MBLooks, for example, the scopes jump and inclusively some tones may be influenced. And I left clear examples in this topic where you can see that this is possible. I don't know if this is "very minimal" or not, but is really so impossible to edit in Premiere without this "very minimal" issue?!? How can it be possible in other softs (Edius, Media Composer, Vegas Pro) and in Premiere not?!?
One more thing: many of us use intermediate codecs in the editing process. Do you find normally that a AVCHD video have the lumninance at approximately 110IRE, to export it directly to Cineform and then import it in Premiere, and the waveform shows the luminance at 100IRE?!? How is this possible?!? So the AVCHD video have a 110IRE luminance, you convert this video to Cineform without changing anything, and then this Cineform video have the luminance at 100IRE?!? And anyone can verify this example.
So, how can one trust in this soft?!?

Strange issue with Multi-Table LTS and report filters (10g)

Hi,
I am having some troubles with the following scenario:
I have a large flattened table that is being used as both Fact and Dimension in the BMM layer. I also have another table that contains some supplementary measures needed by some reports.
Logical Fact table has an LTS that consists of the 2 tables which are joined on 2 columns (eg, a.col1 = b.col1 and a.col2 = b.col2, etc). The columns used in the join also exist in the logical dimension which uses the same flattened table. I use these columns in my report filters.
I have created some Fact measures, some from each source inside the LTS.
What's happening is that when I am using this model in Answers, the query being generated is applying my filtering conditions to both tables, which seems unnecessary to me since they are joined on these columns.
i.e.,
select *
from table1 a, table2 b
where a.col1 = b.col1
and a.col2 = b.col2
and a.col1 = 'Value 1'
and a.col2 = 'Value 2'
and b.col1 = 'Value 1'
and b.col1 = 'Value 2'
The last two lines in the query above should not be happening. I have not mapped these columns anywhere in the BMM to table2 (other than physical layer join), only to table1.
For clarification, it's not hurting the end results from what I've seen, but it is adding additional filtering to the query that can increase overall cost, which I'm trying to avoid.
Any ideas/suggestions?
Thanks
Edited by: odinsride on Jan 31, 2012 5:03 PM

Hi,
I think this is a known issue. I think that the BI Server pulls in both the tables involved in the LTS for any query (Yes, even if the query has only one column from any of the tables in LTS) and so are the filters.
In this case, what I would suggest you is to create 2 LTS (probably 3). One for each physical table (that are being joined in the LTS) and one for both of them joined (may be inner/left/right) etc.
With this kind of setup, when there are reports for any particular column of this logical table, the BI Server can go and choose the corresponding LTS only. However, if there is a report with columns from both the tables, the BI Server would choose the LTS with the join.
Hope this helps.
Thank you,
Dhar

I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing. Now album covers are interspersed with my pictures. I have been using apple tv for a while and never had this happen before

I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing. Now album covers are interspersed with my pictures. I have been using apple tv for a while and never had this happen before

Are you watching this content though iCloud or though from iTunes on your local computer? If it is from iCloud have you tried downloading the content to iTunes and watching it on ATV from that source to see if it still happens? This is geerally a much more reliable way to view the content. Easer to fast forward and rewind too.
- I have a stable internet connection
Clearlly you don't
>(Ive tested on other devices)
Which does not tell you anything about the specific connnection from ATV to iCloud.
>I am able to stream Netflix problem free from my AppleTV without so much as a hicup
Again which does not tell you anything about the specific connnection from ATV to iCloud.
>- I am able to download the episodes to my phone, ipad, and computer without any issues
Again which does not tell you anything about the specific connnection from ATV to iCloud. It does remove your ISP throattly traffice as a possible cause though. So that is good.
Have you checked your wireless rounter? Tried doing the factory restor on it? Upgrading it's firmware? Is it and or ATV getting extreamly hot when this problme happens?

Strange Issue with Guided Nav and filters

Hi All,
I am have a very strange issue with the guided navigation.
I created an answer in BI and when I look at 'Display Results' in Answers everything shows up fine.
SELECT LU_PRODUCT.MAJOR saw_0, case WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date-1 AND current_date+29 then '30 Days' WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date+30 AND current_date+59 then '60 Days' WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date+60 AND current_date+89 then '90 Days' else ' > 90 Days' end saw_1, LU_ACCOUNT.ACCTNBR saw_2, FA_ACCTBAL.NOTEBAL saw_3, (FA_ACCTINT_RATEBAND.NOTEBALXINTRATE)/FA_ACCTINT_RATEBAND.NOTEBAL*100 saw_4, REPORT_SUM(saw_3 BY ), AGGREGATE(saw_4 BY ) FROM LDW WHERE (FA_ACCTBAL.EFFDATE = CURRENT_DATE-1) AND (FA_ACCTBAL.NOTEBAL > 0) AND *(LU_ACCOUNT.TERMMATDATE >= current_date-1) AND (LU_ACCOUNT.TERMMATDATE <= current_date+89)* ORDER BY saw_0, saw_1, saw_2
Type=Report
Report=/users/administrator/Loan Amounts By Maturity Dates - Drill 1
But when I link to this answer via guided navigation the filter seems to change??
SELECT LU_PRODUCT.MAJOR saw_0, case WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date-1 AND current_date+29 then '30 Days' WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date+30 AND current_date+59 then '60 Days' WHEN LU_ACCOUNT.TERMMATDATE BETWEEN current_date+60 AND current_date+89 then '90 Days' else ' > 90 Days' end saw_1, LU_ACCOUNT.ACCTNBR saw_2, FA_ACCTBAL.NOTEBAL saw_3, (FA_ACCTINT_RATEBAND.NOTEBALXINTRATE)/FA_ACCTINT_RATEBAND.NOTEBAL*100 saw_4, REPORT_SUM(saw_3 BY ), AGGREGATE(saw_4 BY ) FROM LDW WHERE (LU_PRODUCT.MAJOR = 'CML') AND (FA_ACCTBAL.EFFDATE = CURRENT_DATE-1) AND (FA_ACCTBAL.NOTEBAL > 0) AND *(LU_ACCOUNT.TERMMATDATE >= CURRENT_DATE-1) AND (LU_ACCOUNT.TERMMATDATE >= CURRENT_DATE-1)* ORDER BY saw_0, saw_1, saw_2
Type=Report
Dashboard=/users/administrator/_portal
Dashboard Page=Loans Maturing
Report=/users/administrator/Loan Amounts By Maturity Dates - Drill 1
I am just it is going to the same report. Any ideas on why this is happening??
Thanks

Yes,
these are simply two different reports, as you can see from the filters...

Strange issue with USB mouse and USB headset.

Good day everyone.
I was experiencing a rather strange issue with my mouse and headset(both USB).
I am using KDE and ALSA, if that matters.
They are working just fine, but sometimes, when I try to lower\raise volume, my mouse derps out. I can move it around, but I can't click on anything(sometimes though, I can click on stuff in window that was active before and sometimes only on KDE panel) until I re-plug my headset. Then, nothing can use my headset until I reboot.
Anybody ever had that problem?

I've had similar problems for some time now. Unfortunately, I don't know what the issue is either, but perhaps we can come up with some setup similarities and narrow it down. I have similar trouble with just alsa or with pulseaudio, so that's not it. It is unrelated to the DE, as it happened for me in both gnome 2 and xfce 4. It is not related to the machine either, as the same quirks occur in other machines with the same headset. I have had inconclusive results with downgrading to kernel26-lts, the ancient kernel. I thought at some point it messed up and I was sure the older kernel didnt help, but after trying recently-ish, I had no trouble for days -- until I found that I didn't have trouble on the main kernel either. ... then a few days later, it showed up again. Very irritating!
https://bbs.archlinux.org/viewtopic.php?id=122475
Does my old thread sound like your issue somewhat?
Essentially, at times, if the headset (wireless) is changed into a different power state (unplugged/plugged) or the mic state is toggled (mute/unmute), things that could be clicked on normally cant unless theyre in the window already focused -- mostly.
What headset are you using? 32 or 64 bit arch? Have you tried downgrading to kernel26-lts?

Strange issue with external monitor, only working when external speakers plugged in (using Thunderbolt to VGA adaptor)

Hey – I am having a very strange issue with my external monitor; where it only works if my external speakers are plugged in and connected.
I am using a late 2011 Macbook pro, running Mavericks 10.9.4, along with an MBox 2 (USB Audio Interface), and two powered speakers (KRK Rokit 5). This setup has had no issues. I have just acquired an external monitor (Benq T2200HD), which I am using with a thunderbolt to VGA adaptor (a cheap Chinese knockoff adaptor).
To start - I plugged the monitor in with the thunderbolt adaptor, and it powers up and works fine. However, there is a nasty buzz coming from the speakers. I did some research and it looks like a simple ground loop issue. I did a bit of troubleshooting, and this is where things get weird.
What I found is - If I unplug the MBox, the monitor loses signal from the computer (displaying ‘No Signal Detected!’). Further, if I keep the MBox plugged in, however unplug both the cables from the MBox to the speakers, the monitor loses signal. It doesn’t matter if the speakers are turned off, however they need to be plugged in (or the monitor loses signal). Weirder still, I can unplug the MBox, however the monitor will work if I plug in the speakers through my macs headphone jack.
Simply put, the monitor only works if there is a direct connection between the computer, the speakers, and the power source. What is going on here? Is the monitor grounding through the computer port, to the speakers (I don’t know how this works, is this possible?). Could it somehow be the cheap VGA adaptor I am using?
Some other information:
- Everything is plugged into the same multi-box for power. I have tried plugging things into separate sources, and the result is the same.
- If I unplug the thunderbolt adaptor, then the speaker noise disappears straight away.
- The ground noise doesn’t appear in my headphones, which are plugged into the MBox.
Any information would be great – am I missing something here, or is this genuinely weird?

Well, I went back into Best Buy to test on 3 other laptops (2 Asus, and their floor model for this Sony). It seems to be doing the same problem so at least I was able to rule out broken hardware issue on my particular laptop.
Here's what I did to test:
Since I couldn't really install Adobe Premiere on their machines, I used the DVIO software (http://www.carr-engineering.com/dvio.htm) and a 5 min clip I captured. I transferred onto their machines, hooked up my Sony D8, and attempted to play the video. It would play for 15 seconds and then stop and jitter with a loud noise (like it does on my laptop). I even tried changing each machine's firewire driver to the legacy one and same results. I pulled a brand new 4 pin to 4 pin firewire cable off their shelf and still the same problem.
I think I've nailed it down to Win7x64 bit Home Edition not playing nice with Firewire driver. Very annoying. I can't find any concrete evidence of this from other users on any of the forums that have my particular problem, but from my own testing, it's all I can conclude.
I have 2 other things I can try:
1. Opening the laptop and looking at the firewire to maybe find appropriate driver (ugh, I don't want to have to open this thing up).
2. Upgrading to Win7x64bit Pro and possibly testing with XP on the new MS Virtual PC (http://www.microsoft.com/windows/virtual-pc/). I can't do it with my Home edition apparantly.
Who needs to view video on an external TV anyways....sheeesh...(scarcasm).
Tim

Strange issue with WEBI schedule Report

Hi All,
I have a strange issue with schedule WEBI reports, a schedule report runs for Hours , i reschedule it again by deleting the instance and the schedule report never got succeed even after running for hours.
Any idea???
regards

Hi Manoj,
1. Try to put some filters in the report and then run the report. if it takes less time, then probably your query is fetching very large data.
2. MDX query error may be the reason , this error come when a query runs endless, please try running the query 2-3 times, or when load on server is less.
Hope this will help,
Anamika.

Strange issue with RAM upgrade: It works but it doesn't! Please help.

Hello Everyone,
I have a very strange issue with my iMac since upgrading my RAM from 4 to 12 gig. When I first installed the new RAM it booted up and ran great. The next time I went to boot the iMac up it swtiched on but didn't get as far as the first white boot up screen. I tried turning it off and on a few times using the power on/off button but still no success. I decided to remove the RAM and reseat it. The computer then booted up again fine. Here's the problem though: when I went to switch my iMac on the next day it wouldn't boot up. Again, I took the RAM out and put it back in and the iMac booted up fine. I've checked the status of the RAM in the system profiler and it reports that everything is OK. So, I'm at a loss. Obviously, I don't want to go through this process every time I want to start up my Mac. Any ideas/solutions would be very gratefully received.
Many thanks in advance.

I completely agree with you. It will be one of the 3 issues you outline. The machine was bought brand new and has never given me a problem. It is just the introduction of the new RAM that has started a problem. However, I did just risk a restart and it booted up fine. I don't know if a restart is any different to shutting down and then pressing the on/off button to start the computer. Maybe my last reseating has done the trick or maybe my thinking is flawed because restarting involves a different process to booting up by pressing the on/off button. I don't know.
In the part of the world I'm sitting in it's night time now so I will leave the diagnostics running and check the results in the morning. I hope the issue is now resolved anyway. This sort of thing takes me back to my dark PC days although in this case I know it's probably not the Mac's fault.
Thanks again. Very much appreciated.

Strange issue with rights of account, used by SSIS (Foreach Loop Container does not return file names without Admin rights on server)

Hello everyone.
Faced very strange issue with account, which is used to run SSIS package.
The specific package uses Foreach Loop Container to retrieve file names within the specified folder, and put them into Import file task.
The package is set up to run under specific service account. This service account is given all permissions (Full control) to the folder where source files reside.
So the issue is: SSIS package fails to execute this task (Foreach Loop Container and then Import), and shows that no files are found in the directory (although files ARE there).
Once we're adding the service account into local Administrators group on the SQL Server, it works! Removing - does not work again. We cannot leave the service account as SQL server's admin as it's prohibited by our IT policies, and is just a bad practice.
Any ideas, please?
MCP

Here's the real log output:
Date 16.04.2014 12:47:09
Log Job History (RU-BW: Update)
Step ID 1
Server Server
Job Name RU-BW: Update
Step Name bw_import_cust_master_data
Duration 00:00:02
Sql Severity 0
Sql Message ID 0
Operator Emailed
Operator Net sent
Operator Paged
Retries Attempted 0
Message
Executed as user: service_account Microsoft (R) SQL Server Execute Package Utility Version 10.50.4286.0 for 64-bit Copyright (C) Microsoft Corporation 2010. All rights reserved. Started: 12:47:09 Error: 2014-04-16 12:47:11.45
Code: 0xC0202070 Source: bw_import_cust_master_data Connection manager "Input" Description: The file name property is not valid. The file name is a device or contains invalid characters. End Error Error:
2014-04-16 12:47:11.47 Code: 0xC0202070 Source: bw_import_cust_master_data Connection manager "Input" Description: The file name property is not valid. The file name is a device or contains invalid characters. End
Error Error: 2014-04-16 12:47:11.48 Code: 0xC0202070 Source: bw_import_cust_master_data Connection manager "Input" Description: The file name property is not valid. The file name is a device or contains invalid
characters. End Error Error: 2014-04-16 12:47:11.48 Code: 0xC020207E Source: Import file Flat File Source [1] Description: The file name is not valid. The file name is a device or contains invalid characters.
End Error Error: 2014-04-16 12:47:11.48 Code: 0xC004701A Source: Import file SSIS.Pipeline Description: component "Flat File Source" (1) failed the pre-execute phase and returned error code 0xC020207E.
End Error DTExec: The package execution returned DTSER_FAILURE (1). Started: 12:47:09 Finished: 12:47:11 Elapsed: 2.324 seconds. The package execution failed. The step failed.
MCP

Strange issue with external monitor, only working when external speakers plugged in

Hey – I am having a very strange issue with my external monitor; where it only works if my external speakers are plugged in and connected.
I am using a late 2011 Macbook pro, running Mavericks 10.9.4, along with an MBox 2 (USB Audio Interface), and two powered speakers (KRK Rokit 5). This setup has had no issues. I have just acquired an external monitor (Benq T2200HD), which I am using with a thunderbolt to VGA adaptor (a cheap non-apple adaptor).
To start - I plugged the monitor in with the thunderbolt adaptor, and it powers up and works fine. However, there is a nasty buzz coming from the speakers. I did some research and it looks like a simple ground loop issue. I did a bit of troubleshooting, and this is where things get weird.
What I found is - If I unplug the MBox, the monitor loses signal from the computer (displaying ‘No Signal Detected!’). Further, if I keep the MBox plugged in, however unplug both the cables from the MBox to the speakers, the monitor loses signal. It doesn’t matter if the speakers are turned off, however they need to be plugged in (or the monitor loses signal). Weirder still, I can unplug the MBox, however the monitor will work if I plug in the speakers through my macs headphone jack.
Simply put, the monitor only works if there is a direct connection between the computer, the speakers, and the power source. What is going on here? Is the monitor grounding through the computer port, to the speakers (I don’t know how this works, is this possible?). Could it somehow be the cheap VGA adaptor I am using?
Some other information:
- Everything is plugged into the same multi-box for power. I have tried plugging things into separate sources, and the result is the same.
- If I unplug the thunderbolt adaptor, then the speaker noise disappears straight away.
- The ground noise doesn’t appear in my headphones, which are plugged into the MBox.
Any information would be great – am I missing something here, or is this genuinely weird?

Hello cgoldberg11
Please go to the below link to test if you are having a speaker hardware failure.
Testing for Hardware Failures (Windows 7)
This will rule out hardware failure, let me know how that goes.
Thanks
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP. .....
Reguards,
Mo

Strange issue with Spry Accordion Panels

Hi, I'm having some strange issues with the Spry Accordion
Panels.
Here is the page:
http://www.bellaclientcenter.com/browncollege/aboutus.html
For some reason when I preview this message it adds extra
characters to the url above, so just delete those off to see the
correct url.
The only browser this does NOT happen in is safari, I'm
seeing it all of my other browsers. You'll notice when you first
load up the page, you'll see that the active panel header
background is green, and the non active is a dark grey. But when
you click one of the other panels they all turn a strange neon blue
color. This is very apparent in firefox.
Any thoughts on this? I've attached the spry css code in case
the problem is there.
thanks so much!!
Jeff

That is because your page is currently invalid. And renders in IE quirksmode..
<base href="http://www.industrialwebsearch.com/">
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd">
So make sure your page is valid, and the animations will go smooth in ie

Strange issue with speaker - stays on after a call has ended

Hi all,
I have the latest iOS version (7.1) on my iPhone 5.
I haven't had any hardware issues before, but 2 days ago something strange has began happening.
Strange issue with speaker - it stays on after a call has ended and plays the sounds that it gets from the microphone.
Only way to stop it is to make another call and hang up.
Any ideas?

oops...we're in the same boat....look m8 that ios 7.1 is rubish i recently after updating mine the ear stop working i called apple customer care we went throu wiv that adviser we restore the phone up 2...3 times nofin happen then da guy told me finally it was not a software problem....but hardware problem and they booked me up 2 take it 2 the near apple store because it is only from apple u can get da matter fixed however if your phone where unlocked outside your network provider or again from the coner street tech....? 4get cos once those form street unlock your phone you just have the same cover or boby let say it ....but your IMEI and all manufacture detail will changed........the good news is if your phone still have manufacture waranty iz free from apple if your waranty run out? apple will ask you 2 pay up 290£.....
hope this replay may hel you m8
stay bless

Strange issue with Exchange system

Hello,
I'm experiencing a strange issue with one of the Exchange 2013 mailbox servers running on Windows 2012. When trying to upgrade it to the new CU5, I'm getting the following errors:
Error:
The local domain needs to be prepared using Setup /PrepareDomain before server roles can be installed.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DomainPrepRequired.aspx
Error:
The Mailbox server role isn't installed on this computer.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.UnifiedMessagingRoleNotInstalled.aspx
Error:
The Mailbox server role isn't installed on this computer.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.BridgeheadRoleNotInstalled.aspx
Error:
An unsupported operating system was detected. Exchange Server 2013 Client Access, Mailbox, and Edge Transport server roles support Windows Server 2008 R2 SP1 or later and Windows Server 2012.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.ValidOSVersion.aspx
In the Exchange organization there are 2 CAS servers, 2 MBX servers.
Memento Mori

Hi Vick,
Based on my research, I suggest you should upgrade the AD first.
1. Exchange 2013 CU5 contains schema changes. To upgrade the Schema to CU5 you can execute the following command:
Setup.exe /PrepareSchema /IAcceptExchangeServerLicenseTerms
2. And you also should upgrade the
Configuration Partition and the Domain Partition with the following command:
Setup.exe /PrepareAD /IAcceptExchangeServerLicenseTerms
Setup.exe /PrepareDomain /IAcceptExchangeServerLicenseTerms
3. After finished above two steps, now you can start to upgrade an Exchange 2013 server to CU5. Open a command prompt and enter the following command:
Setup.exe /Mode:Upgrade /IAcceptExchangeServerLicenseTerms

Strange issue with the render percentage indicator

Hello,
I'm getting a strange issue with the FCPX interface - the little gauge that shows the percentage complete a render is - seems to have gone crazy! and is spinning round. I've tried changing project/ restarting fcpx and also restarting the mac!
heres a screen capture of it in action... https://www.dropbox.com/s/o9bwexyuntx0jxd/what.mov

This is traced back to a backup issue.. Hopefully a fix will come with 10.1.4
At this time, the solution is to turn off backup per library...
10.1.3 update "backup" mess

Strange Issue With QIP 7100 STB and Sony Bravia TV

Similar Messages

Maybe you are looking for