Strange PXE Boot Issue

This issue has me stumped. I've ordered in a new Dell system (Optiplex 3030 AIO) and I'm having issues PXE booting it, but only on some vlans. If I pxe boot in my work room where I do most of the imaging it pxe boots fine. If I try to pxe boot out on the
floor (same site) then it loads the boot.sdi but after this it tries to load the WIM file and it is very slow and it eventually fails. The message is that there is an inaccessible boot device.
The strange thing is if I take another modal desktop or even laptop, it pxe boots fine in those locations.
Something to note is I do have an SSD in the Optpliex 3030, however I have had SSDs in my laptops as well.
I have investigated the smspxe.log file and found that when it starts to load the WIM file I get an error saying "Failed to read PXE settings. The system cannot find the file specified. Error 80070002. This is further followed up with some warnings
about certificates not set.
I should also mention that I have played around with the PXE registry setting RamDiskTFTPBlockSize. I have tried all values up to 16384 with no change noticed.
Does this make sense at all?

Hi,
Really weird :( I never had this issue, but based on your input, the issue appears before the wizard so I don't think it has anything to do with the task sequences, OSes or Applications. Here's what I would do to investigate further :
Check UnattendPE_x86/64.xml to verify if there is a step running before litetouch.vbs that could cause this issue
Check WinPE log files (Netsetup.log, wpeinit.log) for additional info
If possible Try without drivers on a Hyper-V VM (Hyper-V additions are already part of the core Win7 image, so no need to add drivers)
Good luck, if you find anything, please share the solution here :)
David Sebban | Nelite North America | http://www.nelite.com/community/b/dsebban/default.aspx

Similar Messages

PXE boot issues with Windows Deployment Services

I am trying to move from FOG to WDS after running in to serious UEFI issues with FOG.Right now I'm stuck with machines PXE booting to WDS server.I keep getting the message ProxyDHCP service didn't reply to request on port 4011.WDS and DHCP are on different servers. There are plenty of IP addresses available, and they are on the same subnet. I did originally configure DHCP option 60, but deleted that option after troubleshooting. I have configured Windows Firewall to allow inbound and outbound connections on UDP ports 67-69 and 4011 on both DHCP server and WDS server. I have also tried just using IP address in DHCP option 66. As for option 67, I don't even know the right bootfile name to use at this point, figured I'd tackle that if I ever get past this error message.I have tried restarting the WDS service several times, as well as the...
This topic first appeared in the Spiceworks Community

After working with many companies in their Office 365 Change Management and End User Adoption strategies, we’ve found that companies who make it fun have very high success rates. So what can you to make it fun?Host an Office 365 Showcase.We’ve helped companies produceOffice 365 Showcases, which have a lively, trade show flair. Kiosks are set up in a cafeteria, meeting room or other convenient location. Hosting each kiosk is a departmental Office 365 Power User who demonstrates a unique aspect of the software to everyone who stops by.Read more about how to make Office 365 Change Management and End User Adoption Fun

PXE boot issue with DHCP and SCCM server on different subnets

I'm working with a client on the operating system deployment module of SCCM.
Their network configuration currently has a single large subnet for client
computers with a DHCP server on the same subnet. The SCCM subnet is
configured on a seperate subnet with no DHCP server on the subnet. We want to
configure client computers to be able to boot using the PXE client to deploy
OS images to the machines but can not get PXE-boot to work correctly.
Also, the client does not want to make changes to their network
infrastructure routers or switches to remedy this problem. Are there settings
on the DHCP or SCCM servers we can implement to make this work? If so, what
needs to be installed or configured on each server. We currently already have
WDS installed on the SCCM server and the SCCM server is configured as a PXE
Service Point within SCCM. Both WDS and the PXE Service Point seem to be working fine.
Any help would be appreciated.
Thanks,
Gary

I am Brazilian,
sorry for wrong english
My DHCP is on linux,
in my own structure VLANS
The system center is on the network
10.0.4.0/24
The machines on the network 10.0.5.0/24
The problem is that the machines that
are not on the same network system center
can not boot
I tried configuring / etc/dhcp3/dhcpd.conf
follows
option vendor-class-identifier "PXEClient";
option bootfile-name "\
\ SMSBOOT \ \ x86 \
\ wdsnbp.com";
option tftp-server-name
"10.0.4.101"; ---->
IP server
But it did not work, anyone know
how to configure?

SCCM 2012 pxe boot issue

My test machines cannot PXE boot.
My lab environment is very simple:
10.10.0.0/24 subnet
10.10.0.5 = Server2012, DHCP, DNS, SQL Server 2008 R2 Sp2
10.10.0.7 = Server2012, SCCM2012
All machines are Oracle VM Box virtual machines connecting through the same virtual network.
Setup the PXE service from DP properties. I let SCCM install WDS. WDS in Server
Manager does not have a server node, but the WDS service is running. DP PXE tab is configured as follows:
"Enable PXE support for clients" is checked
"Allow this distribution point to respond to incoming PXE requests" is checked
"Enable unknown computer support" is checked
"Require a password when computers use PXE" is not checked
"User device affinity" is set to "Allow user device affinity with automatic approval"
PXE is configured to respond on all network interfaces
The PXE server response delay is 0 seconds
The DHCP server has options configured as follows:
Option 66: 10.10.0.7
Option 67: smsboot\x86\wdsnbp.com
Both DP and MP on SCCM server are configured for HTTP.
Both x86 and x64 boot images have been distributed to DP. The media was updated after
PXE was enabled on the DP.
Both x86 and x64 boot images have "Deploy this image from the PXE service point" enabled on the Data Source tab of their properties
SMSPXE.Log
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777219" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
]LOG]!><time="15:05:09.346-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="libsmsmessaging.cpp:6544">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: no advertisements found]LOG]!><time="15:05:09.346-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: No boot action. Aborted.]LOG]!><time="15:05:09.441-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: Not serviced.]LOG]!><time="15:05:09.441-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="database.cpp:483">
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777219" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
]LOG]!><time="15:05:09.705-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="libsmsmessaging.cpp:6544">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: no advertisements found]LOG]!><time="15:05:09.705-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">

Resource ID is already present in the Unknown Computer (Windows 7) Properties please look into it and
OSD Task Sequences is there :(.

Troubleshooting PXE boot issue

SCCM R2 not able to PXE boot from Surface pro. I am new to environment. How can I tell if PXE broadcasts are making it to device and to sccm ? I recieve the following output in CMTRACE in SMSPXE.log .. Am I doing something completely wrong ?
Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16781189" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction LastPXEAdvertisementID=""
LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
Mj

smspxe.log will display the MAC address if the broadcast reached the server.
You have to use Wireshark or Netmon if you want to find out if the response reaches the client.
Torsten Meringer | http://www.mssccmfaq.de

PXE Boot issues with Latitude E5450.

Our SCCM 2012 is SP1 and it does not support Windows 8.1.
I had tried to capture the OS through network but there were issues connecting and smsts.log indicated share not reachable. Hence, I captured the OS in the D:\ of the machine.
Now after creating TS and deploying the OSD machine boots to PXE and starts to download boot image files and instantly restarts to Windows. I have performed below steps..
1. Got the network drivers and updated the boot image with the same
2. Checked the BIOS settings and time is updated correctly
3. Used an old boot image that was used to capture another model laptop with Windows 8.1 and still same issue.
Getting the below errors in smsts.log
uExitCode == 0, HRESULT=80004005 (e:\nts_sccm_release\sms\server\pxe\tspxe\tspxe.cpp,185)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
Failed to download pxe variable file. Code(0x00000001)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
PxeGetPxeData failed with 0x80004005 TSPxe
3/26/2015 6:29:17 PM 792 (0x0318)
HRESULT_FROM_WIN32(dwError), HRESULT=80004005 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmbootstraputil.cpp,1416)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
TSMBootstrapUtil::PxeGetPxeData(&bPxeBooted, sVariablesFile, sPxePasswd), HRESULT=80004005 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,2623)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
oTSMediaWizardControl.Run( sMediaRoot, true, sTSLaunchMode ), HRESULT=80004005 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmbootstrap.cpp,1078)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
Execute( eExecutionEnv, sConfigPath, sTSXMLFile, uBootCount, &uExitCode ), HRESULT=80004005 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmbootstrap.cpp,1183)
TSPxe 3/26/2015 6:29:17 PM
792 (0x0318)
Exiting with return code 0x80004005 TSPxe
3/26/2015 6:29:17 PM 792 (0x0318)
Any advise would be helpful..

Our issue with the Latitude E5450 ended up being due to a boot image that wasn't being properly updated and/or pointed to during the task sequence set up. There also seemed to be some strangeness with the replication because the WIM file listed on
the server file system was showing as, for example, boot.XXXX.XXXX.wim (double name). As a result, when we would update the boot image with the correct NIC driver, the system was still pointing to, for example, boot.XXXX.wim.
We ended up re-creating the boot image from scratch using our base boot.wim image and using the 19.2.0.0/12.12.50.4 driver version for the I218-LM NIC, found at the download link below. If you recreate the boot image, don't forget to re-add all of the
NIC drivers, redistribute the boot image, and change which boot image your Task Sequence will be pointing to.
http://www (dot) dell (dot) com/support/article/us/en/19/SLN294178/EN

T430 PXE boot issues

First off let me list my hardware/software
MDT/WDS server:
MDT 2012
Windows server 2008 R2
I have a fully working MDT PXE server with a WDS images. Basically I have a MDT server that gets the PXE request and then boots off the WDS image to start the imaging process. This works fine on the lenovo thinkcenters ok and I can boot off the CD from the MDT server. But when I boot from the network card I get no response or no DHCP.
- I have downloaded all the drivers for the Thinkpad and injected them into the MDT and WDS for the WINPE image
- I have updated the BIOS to the latest ver 2.09
- I can boot from the cd just fine to my server and pull an ip
Not sure why this laptop model is failing on the boot process to the network.. Anyone see this issue?
Solved!
Go to Solution.

Resolved by applying settings "Port Fast - Enable" to the port of Cisco Switch connected to the laptop or pc.

Strange Powerbook Boot Issue

I am currently seeing a very odd issue with my 15 inch Powerbook G4 1.5ghz. When the power button is pressed, the notebook will power up, I can hear a chime, but then it powers itself down about 5-10 seconds after the hard drive starts spinning up.
The interesting part is that if I press fn-f7 repeatedly as soon as I hear the chime, video appears on the screen and I can use the option key to select my firewire drive and boot normally. I have tried clearing nvram via open firmware (the keys for clearing PRAM do not work for some reason) and holding down the power button with the battery and power disconnected to clear the power management chip (forgot the exact term.) The fix only works with fn-F7. Using command, option, control-F7 or F7 by itself does not seem to help.
The internal hard drive has been getting ready to check out over the last 6 months ago and recently it gave up the ghost altogether. I can still boot off my firewire backup if i use the F7 trick mentioned above. I suppose that the bad hard drive could be causing the no video/boot problem, but I would not think that hitting F7 would help if that were the case. The notebook was dropped and is not much to look at, but it works great once you see the apple logo on the screen.
I am planning on replacing the drive, but I would love to get this fixed before investing any money in the unit. Any help would be greatly appreciated.
Thanks.
Jake

There might be an issue with your RAM or with the RAM slots on your machine. Try removing one module & running the machine with just the one. You could also try Rember:
http://download.cnet.com/Rember/3000-2094_4-52452.html
To see if it finds any errors.
~Lyssa

PXE Boot Issue

Hi folks,
It's been a while since I last setup my SCCM server to do OSD. I have currently just setup a new server to do this again, but I think I'm missing a few steps to get the OSD working correctly. I have WDS installed, setup PXE Service Point inside SCCM, and also have added the x86 and x64 boot images under OSD section of configmgr console. I can't remember if I have to add those same boot images to the WDS console as well, or what other steps I need to do to get this thing pushing out my os images again. Anyone point me to some docs or soemthing helpful it would be appreciated.
Thanks, Jay

Hi ChrisMullins, thanks x For your post, it may help me in my problem described here: http://social.technet.microsoft.com/Forums/en-US/configmgrosd/thread/a83237d8-55d7-4b99-bc1c-10c3bbf5aef2 .
Please correct me if I wrong:
1.     Network configuration:
1.1.   DHCP options (http://www.networksorcery.com/enp/protocol/bootp/options.htm):
1.1.1. Option 66 - TFTP server name
1.1.2. Option 67 – Boot file name
1.1.3. Option 60 – This is value tell PXE clients where to find the OS deployment server
In other way my DHCP scope must be configured:
# Configure
option 66 "<FQDN of SCCM server>"
option 67 "SMSBoot\X86\wdsnbp.com"
# MUST NOT be configures
option 60 not configured
1.2.   Configure Cisco ( switch or router) options:
1.2.1. Configure allow to transmit all dhcp and bootp packets by using either one of commands:
1.2.1.1.         ip dhcp relay information trust-all (Description: Configure all interfaces on a router as trusted sources of the Dynamic Host Configuration Protocol (DHCP) relay agent information option, use the ip dhcp relay information trust-all command in global configuration mode. To restore the interfaces to their default behavior, use the no form of the command).
1.2.1.2.         ip dhcp relay information trusted (Description: Description: Configure selected interfaces on a router as trusted sources of the Dynamic Host Configuration Protocol (DHCP) relay agent information option)
1.2.2. Configure allow to transmit all dhcp and bootp packets directly to DHCP server using command ip helper-address <IP address>( Description: This subcommand tells the router to forward UDP broadcasts, including BootP, received on this interface to <IP address>)
1.2.3. Configure allow to transmit all dhcp and bootp packets directly to PXE server using command ip helper-address <IP address>
So Cisco must be configured as follows:
# Configure router to permit all dhcp and bootp packets
ip dhcp relay information trust-all
# this will configure forward dhcp and bootp packets to dhcp server
ip forward-protocol udp
interface <ethernet interface to witch DHCP broadcast packets from client go>
ip address <IP address> <mask > # <??? Is it must be here ???
ip helper-address <IP Addres of DHCP Server>
# this will configure forward dhcp and bootp packets to Server with PXE Service point
ip forward-protocol udp
interface <ethernet interface to witch DHCP broadcast packets from client go>
ip address <IP address> <mask > # <??? Is it must be here ???
ip helper-address <IP Addres of PXE Server>
Or more secure manner configuration must be as follows:
# Configure router to permit all dhcp and bootp packets
interface <ethernet interface to witch DHCP and BootP broadcast packets go>
ip dhcp relay information trusted
# this will configure forward dhcp and bootp packets to dhcp server
ip forward-protocol udp
interface <ethernet interface to witch DHCP and BootP broadcast packets go>
ip address <IP address> <mask > # <??? Is it must be here ???
ip helper-address <IP Addres of DHCP Server>
# this will configure forward dhcp and bootp packets to Server with PXE Service point
ip forward-protocol udp
interface <ethernet interface to witch DHCP and BootP broadcast packets go>
ip address <IP address> <mask > # <??? Is it must be here ???
ip helper-address <IP Addres of PXE Server>

Error 25: Disk read error - pxe booting issue

Hello All,
Currently trying to install solais 10 via pxe on a virtual machine on local harddisk.
Running in fully virtualized mode the "Error:disk read error 25"
Also running in Paravirtualized mode i get an "Error: Boot loader didn't return any data!"
Please guide me how to proceed.
Regards,
Maghesh
Edited by: 816522 on Dec 16, 2010 1:21 PM
Edited by: 816522 on Dec 20, 2010 9:59 AM

Hi Herb
I got a similar error for a PV image. While setting it up I had used dd command to increase its size to add a couple of partitions. It also has a shared disk attached for RAC usage. It was rebooting fine for the first few times. Now after a complete shutdown it is returning the boot error message as below:
Start - /OVS/running_pool/882_szguestvm5_Sharon_RAC_N2
PowerOn Failed : Result - failed:<Exception: return=>failed:<Exception: ['xm', 'create', '/var/ovs/mount/D56A962F3D1046B6AE4839A28EB72B96/running_pool/882_szguestvm5_Sharon_RAC_N2/vm.cfg'] => Error: Boot loader didn't return any data!
>
StackTrace:
File "/opt/ovs-agent-2.3/OVSXXenVM.py", line 57, in xen_start_vm
run_cmd(args=cmd)
File "/opt/ovs-agent-2.3/OVSCommons.py", line 69, in run_cmd
raise Exception('%s => %s' % (cmdlist, p.childerr.read()))
>
StackTrace:
File "/opt/ovs-agent-2.3/OVSSiteVM.py", line 113, in start_vm
raise e
Any help is appreciated.

Strange CD Boot issue - Satellite 1805

I have a Satellite 1805-S207 that cannot boot from the CD. I have went press F12 and then C, but I notice that it doesn't even test the drive (I should get a access light?). I sent the priority order in the BIOS to boot from CD first, but that hang the machine. I thought may be the CD drive is defective, but I can still burn CD and playback works just fine.
I updated the BIOS to the latest version and also updated the DVD drive to the latest version. So far this does not solve the problem. This mean I can't install if my HD goes south :-(.
Any ideas?
One possible work around would be to create a floppy that bootstraps the loading of the CD. Has anyone seem something like that?
Paul

My Satellite 1200 has had the same fault.
Try resetting via the Toshiba HWSetup (the one with a spanner icon) in Control Panel. There you will find a section Boot Priority.
Good luck

Issues with Boot Images & PXE Booting Since SP1 Install

Good Afternoon All -
I recently updated to SP1, had some issues, but they got resolved. Now, though, I'm having an issue booting to PXE as well as updating any boot images created
before SP1 was installed. Booting to USB Bootable media using a newly created boot image seems to work fine.
Boot Images
When I update my DPs for any of my boot images in SCCM, they fail and i get the below error:
Error: The wizard detected the following problems when updating the boot image.
• Failed to install required components into the boot image
The SMS Provider reported an error.: ConfigMgr Error Object:
instance of SMS_ExtendedStatus
• Description = "Failed to insert OSD binaries into the WIM file";
• ErrorCode = 2152205056;
• File = "e:\\nts_sccm_release\\sms\\siteserver\\sdk_provider\\smsprov\\sspbootimagepackage.cpp";
• Line = 4566;
• ObjectInfo = "CSspBootImagePackage::PreRefreshPkgSrcHook";
• Operation = "ExecMethod";
• ParameterInfo = "SMS_BootImagePackage.PackageID=\"BBS0012F\"";
• ProviderName = "WinMgmt";
• StatusCode = 2147749889;
I've even gone as far as removing all drivers from the boot image, but still get the same message. I was able to create a couple of
new MDT boot images which seem to work fine, though. I am not sure which log file is for boot images, but nothing appeared in distmgr.log.
PXE Booting Issue
After trying many things, I removed PXE config from my site and uninstalled WDS then started all over again. Here's what I did and my results. Please tell me what I'm missing...
After uninstall & server reboot, I enabled PXE + every option in DP tab in SCCM
It automatically installed WDS (same server) and added the two boot images I had checked for PXE use. one x64 and one x86.
I checked my DHCP Scope whose values hadn't changed sine it worked (that I know of). They are:
Option #66: 192.168.20.37 (SCCM Server/DP/PXE)
Option #67 \boot\x86\wdsnbp.com. I've tried \boot\x86\pxeboot.com as well as each of these with x64.
When I PXE boot from a workstation, I receive an IP, a bit of info, then it goes to Contacting Server.... When trying one of the boot files above, I was prompted for F12, but receved a blue screen with error. When trying all other boot files,
they just hang at Contacting Server until they timeout.
I looked at SMSPXE.log and found something interesting...
The IDs for the two boot images I have assigned to PXE are ABC003B3 & ABC00B36. In the smspxe.log, though, it keeps repeating "could not find boot image ABC0012F! 12F does exist and is a boot image,
but not the one I want to use by any means and does not have PXE checked.
I went ahead and checked 12F, updated DPs (which failed - see above); unchecked it; then updated the DPs again. PXEBoot.log showed that it was trying to remove the 12F files from RemoteInstall which was a good sign. I then restarted the WDS service
and tried PXE booting again. Yet again, it failed and was still looking for 12F.
Any suggestions / Ideas??? Thanks!
UPDATE 1
I just changed option #67 to \smsboot\x86\pxeboot.com then restarted the WDS service. I booted to PXE and this time was asked to hit F12. I did so and it looked as if it would work.
Instead, I got a blue screen with the following error:
Recovery
Your PC needs to be repaired
The boot configuration disk contains errors or is missing
file: boot\BCD
Error Code: 0x000000f
I think that it's the same error as before, but is blue instead of black due to new Win8ADK perhaps. Thanks
Ben K.

Update 4
Sorry to make this the longest post ever :)
I just read that others with this error checked DISM.log. I did so when running a DP update for the boot image and got the below errors:
2013-01-11 16:27:04, Info DISM DISM Provider Store: PID=1636 TID=5104 Failed to get and initialize the PE Provider. Continuing by assuming that it is not a WinPE image. - CDISMProviderStore::Final_OnConnect
2013-01-11 16:27:07, Info CBS Failed to find a matching version for servicing stack: C:\Windows\TEMP\BootImages\{DADCFE01-3557-4058-99CC-2A15EDF905AF}\mount\Windows\WinSxS\amd64_microsoft-windows-servicingstack_31bf3856ad364e35_6.1.7600.16385_none_655452efe0fb810b\
[HRESULT = 0x80070490 - ERROR_NOT_FOUND]
2013-01-11 16:27:07, Info CBS Failed to find servicing stack directory in online store. [HRESULT = 0x80070490 - ERROR_NOT_FOUND]
2013-01-11 16:27:07, Warning DISM DISM Provider Store: PID=4104 Failed to Load the provider: C:\Windows\TEMP\0555ABC5-006D-4C3F-B79F-EA0E723FA971\MsiProvider.dll. - CDISMProviderStore::Internal_GetProvider(hr:0x8007007e)
2013-01-11 16:27:07, Warning DISM DISM Provider Store: PID=4104 Failed to Load the provider: C:\Windows\TEMP\0555ABC5-006D-4C3F-B79F-EA0E723FA971\TransmogProvider.dll. - CDISMProviderStore::Internal_GetProvider(hr:0x8007007e)
2013-01-11 16:27:07, Error DISM DISM Package Manager: PID=4104 The package WinPE-Scripting-Package is not applicable to the image. - CPackageManagerCLIHandler::Private_ProcessPackageChange
2013-01-11 16:27:08, Info DISM DISM Package Manager: PID=4104 Error in operation: the package is not applicable. (CBS HRESULT=0x800f081e) - CCbsConUIHandler::Error
2013-01-11 16:27:08, Info CBS Failed to unload offline registry: {bf1a281b-ad7b-4476-ac95-f47682990ce7}C:/Windows/TEMP/BootImages/{DADCFE01-3557-4058-99CC-2A15EDF905AF}/mount/Windows/System32/config/SOFTWARE,
the client may still need it open. [HRESULT = 0x80070005 - E_ACCESSDENIED]
(The above one appears 8 times - almost in a row)
2013-01-11 16:27:08, Error DISM DISM Package Manager: PID=4104 Failed while processing command add-package. - CPackageManagerCLIHandler::ExecuteCmdLine(hr:0x800f081e)
Help! Thanks :)
Ben K.

Toshiba L755 is the only one that will not PXE BOOT

I have a few host on my network which it has VMWare 10 installed, successively performed deployment into those machines(Hosts and created VM"s). Now, I do have also a Toshiba L755-S5258 that will not complete the process, it does not give any
errors. The following is the messages it gives.
Client MAC ADDR: xx xx xx xx xx xx GUID: XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXX
Client IP:XXX.XXX.X.XX MASK: XXX.XXX.XXX.x DHCP IP: XXX.XXX.X.X
Gateway IP: XXX.XXX.X.X
Downloaded WDSNBP...
Press F12 for network service boot
Windows Deployment services: PXE boot Aborted.
PXE-MOF: Exiting Intel PXE ROM
This si the only unit that does not follow through with the deployment
Note that I've deleted other machines that I successively deployed to from the Known Computers on Active Directory User and Computers, with not good results
Please any one help me decipher this headache

Hi,
Are your using the WDS for the Windows deploy? A network boot program (NBP) is the first file that is downloaded and executed as part of the network boot process and it controls
the beginning of the boot experience (for example, whether or not the user must press F12 to initiate a network boot). NBPs are specific to both the architecture and firmware of the client. You must accounting the screen press F12 to allow the system boot
from the WDS. The VMware® workstation PXE booting issue please ask your software vendor.
The related KB:
Managing Network Boot Programs
http://technet.microsoft.com/en-us/library/cc732351(WS.10).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Pxe boot sun x4170-m2 LSI raid 5 disks issues 2.10_u9 rel

Hi Gurus,
I am trying to image sun fire x4170-m2 series servers with Latest solaris 10.u9 patch set using Raid-5 disks setup with one hot-spare. Pxe boot works but i minboot not able to find raid-5 disks which is about 1.2 TB disks size. Where as if i used DVD to boot the servers it works properly. What i am missing. Here is my pxe entry and menu.list<mac-address> entry. I tried to insert driver LSI megraid driver with x86.miniroot, but it's already available into kernel/drv.
-dhcpd.conf entry.
host foobar { hardware ethernet 00:21:28:8E:3D:F2; fixed-address 10.228.150.14; next-server 140.87.100.21; filename "010021288E3DF2"; option host-name "foorbar.us.oracle.com";}
menu.1st.<mac-address>
cat /tftpboot/menu.lst.010021288E3DF2
default=0
timeout=30
min_mem64 1024
title Solaris_10 install_x86_64_2.10_u9
kernel /I86PC.Solaris_10-9/multiboot kernel/unix - install - nowin -B console=i86pc,install_config=140.87.100.21:/export/jumpstart_x86_64_2.10_u9,sysid_config=140.87.100.21:/export/sysid_2.10_u9/10.228.144,install_media=152.68.248.67:/vol/local/x86/solaris/100/base/u9/mar2011,install_boot=140.87.100.21:/export/install_x86_64_2.10_u9_new/boot -v -m verbose
module /I86PC.Solaris_10-9/x86.miniroot
Please let me know if you have any solution for this issue.
Thanks & Regards,
-Sunil.

Hi.
Read thread:
X4x70 (M1) with extremely slow disk I/O
Try workaround the problem by adding the following line to /etc/system and then reboot:
set idle_cpu_no_deep_c = 1
Regards.

Issues with PXE booting

Hello guys I'm having some issues with PXE booting on my DP.
I've installed them on a single server with SCCM installed and using it as a DP.
When I've tried to PXE boot I'm having some issues. Please see the screenshots below:
Here is the PXE log:
Below are my pictures of 066 and 067

Hi,
have you run the
WDSUTIL /Set-Device /Device:<name> /ReferralServer:<ServerName>
command?
From:
Managing Network Boot Programs
https://technet.microsoft.com/en-us/library/cc732351%28v=ws.10%29.aspx
"If you are not using DHCP options 66 and 67, in order to configure a network boot referral, you must prestage the client and you must run
WDSUTIL /Set-Device /Device:<name> /ReferralServer:<ServerName> to specify the server that the client should use."
Regards,
Stoyan
Hi Stoyan I have not, as I'm using the DHCP optioins

Strange PXE Boot Issue

Similar Messages

Maybe you are looking for