Strange reconciliation issue

New blackberry curve verizon user here. Successfully added my .edu IMAP account and can send and receive emails.
After reading messages on the curve, they show as read on outlook and on the university's webmail site.
If I delete a message on the curve, it still appears when i access my email through my computer. If I delete the msg with my computer, it still appears on the curve.
In addition, emails sent from my curve won't appear as sent mails when i logon through my computer. same goes for emails sent from my computer first.
Any way to fix this deletion/sent mail issue?

Does your .edu account have web access too? Just to make sure there are no problems with your client configuration I would check through web access.
That said, under Messages > Options > Email Reconciliation
for the message service that is your edu account is wireless reconcile on and is delete on set to mailbox & handheld?
If you've found a solution through a post; please mark it as a solution.
If someone's was particularly helpful, give them kudo's!.
Get busy living, or get busy dying.
http://blog.port3101.org/hdawg/

Similar Messages

Strange performance issue with 3510/3511 SAM-FS disk cache

Hi there!
I'm running a small SAM-QFS environment and have some strange performance issue on the disk storage part, which somebody here might be able to explain.
Configuration: one 3510, dual controller, RAID-5 9+1, one hot spare and one disk not configured for whatever reason. The R5 logical drive hosts a 150GB LUN for SAM-QFS metadata (mm in SAM-FS speak) and a 1TB LUN for data (mr in SAM-FS speak). Further, there are two small LUNs (2GB, 100GB) for some other purpose. Those two LUNs have nearly no I/O. All disks are SUN146G. Host connection is 2GBit, multipathing enabled and working.
Then the disk cache became too small, and the customer added a 3511 expansion unit with SUN300G disks. One logical drive is a RAID-1, 1+1, used for NetBackup catalog. The other is a RAID-5, 8+1, providing two LUNs: 260GB SAM-FS metadata (mm) and 1.999TB SAM-FS data (mr).
For SAM-FS, the LUNs form two file systems: one "residing" in the 3510, the other "residing" in the 3511 expansion. Cabling is according to the manual and checked several times by several independant people. Operating system is Solaris 10, hardware is a V880.
The problem we observe: SAM-FS I/O on LUNs on disks inside the 3510 is fine. With iostat, I see 100MB/s read and 50MB/s write at the same time. On the SAM-FS file system which is running on the two LUNs in the 3511, the limit seems to be at 40MB/s read/write. Both SAM-FS file systems are configured the same in regards of block size.
In case I have activity on both SAM-FS file systems, I see 100MB/s+ on the LUN running inside the controller shelf and another 40MB/s on the disk runnin in the 3511 expansion chassis. So, the controller is easily capable of handling 150MB/s.
Cache settings in the 3510 controller are default I think (wasn't installed by me), batteries are fine.
Is this 40MB/s we experience a limitation by the expansion shelf? Don't think so. Anybody has any ideas on this? What parameters to check or to change? Any hint appreciated. I can also provide further details if needed. Thank you.
wolfgang

SUN300G disks sound like 300GB FC disks.
Depending on how many files are in the SAMFS file system, sharing the mm and mr devices on the same RAID array can be a pretty horrible idea. In my opinion and experience, it's almost always better to NEVER put more than one LUN on a RAID array. Period. Putting more than one LUN on an array results in IO contention on that array. And large, unnaturally configured (9+1? Why?) RAID arrays will have problems from the start.
What are the block sizes used on the RAID arrays? It wouldn't surprise me to see that the RAID array on the expansion tray has a very large block size. Larger block sizes are, in general, not better. Especially for SAMFS metadata - which IIRC is something like 8k or 16k blocks.
I suspect what is happening is most of the metadata updates are going to the mm device on the new array, contending with the IO operations on the file data.
How much space is left on each mm device? What does "iostat -sndxz 2" show when you're having the IO problems?

Strange import issue .. no longer works in 2.6 or Beta 3

Strange import issue.
I use LR-2.6 everyday but have only played around with the LR-3 for a limited amount of time so the other day I decided check it out and tried to import a handful of RAW(canon) files on a SDxc-8g card via a USB card reader. I set it up to copy and convert to DNG, apply a few keywords and Metadata but when I tried it acted like it imported the first image and then froze. Card reader lights stopped blinking and just stayed on, program task bar doesn’t show any progress, not even for the first image. I then went to the folder that I was going to have the images copies to and it contained a file of the first image, but there is no indication that LR-3 even created it and it doesn’t show up in the catalog. When I tried to close out LR-3 is popped up the “in the middle of a task warning” so I just closed the program and tried it a couple more times to no avail.
So I though o well I will just open up LR-2.6 and import them from there, guess what now LR-2.6 does the exact same thing!!
I thought maybe my card reader was a POS but I was able to drag all the files to a new folder on my desktop and import them from there, nope. Tried rebooting a couple times, even opened a new catalog to test with, in both LR-2.6 and LR-3 and neither will work..
I am stumped any ideas?

Thank you for everyone's assistance
I actually figured out what the problem was, like most issues it comes back to operator error, it seem I had inadvertently chose a "rename file on import" template that I had set up to name the files based on a custom fill-in field in the Meta Data, I normally only used that template when I was exporting images that had been completely edited, so being these images were new imports that field was blank, hence it would import the first image and then do to " don't import subjected duplicates" being checked it would just stop the import process.

Strange Catalog Issue or bug. Help, photos disappeared help?

My images disappeared in the catalog. They are not missing, they are just not visable. I think there is a bug in the Fliter section.
Let me explain. I have one Main folder with 5 Sub folders. All those folders contain random amounts of images. (i.e. the path would be... Photo/2010/BeachShoot, or Photo/2008/PartyPics... etc).
I imported 5 years of images, hence 5 Sub Folders. I was randomly flagging images to be rejected with the 'x' key. Basically routine maintenance... flag so many, then call up only the rejected photos in the grid view, select all, then delete. Remove the Flag Filter... repeat process over and over... Basic, simple work...
Now... doing the exact some thing.. I removed all Flag filters and my images are no longer appearing in the catalog. I tested, by turning on flags, off flags.. etc. The images did not accidentally get deleted. I checked my hard drive location. Images are there. I rebooted the machine, I opened up another catalog, to trick it back... did not work. I tried to re-import the images.. but it says they are already in the catalog.
Strange part: On the Left Sidebar window, under Catalog "All Photographs" it shows the correct number of photos in the catalog. However... the strange part... Under "Folders" in the Left Sidebar beneath Catalogs my Main Folder shows "Zero" number of images. But, if I click on a sub root folder where the images reside, they number changes from Zero to the correct number of images and my images reappear on the screen as normal..
The work around... click on every subfolder...
The solution... Unsure? Help!
john
Strange Catalog Issue or bug. Help, photos disappeared help?
System: Mac OS X 10.7.2
Lightroom 3.6

We all get there sometimes Glad it was so easy!
Beat

Strange Printing Issue With New HP & Pages

Hello!
I have a very strange printing issue with a new HP printer. I have written pages documents heavy in Texts which are located within tables. The documents print fine on a Cannon and Epson printer and look great but when I print the document on my new HP Laserjet Pro 400 Colour M451nw some of the text on some rows come out of the printer looking like they are bold / slightly fuzzy. This only happens with some of the rows of text, not all of them. The font is the same in every row with the same format.
You can see this in the attached image. The first line (Thanks very much) has printed correctly but the subsequent lines look bold / slightly fuzzy.
After a lot of testing the only way I can resolve this is if I copy the content into a new pages document and only then it will print and look ok with the HP printer.
This must be a problem within my origional document. I would simply copy and paste everything into a new document however this would take a very, very long time (over 5 years of work producing teaching materials and over 100 documents and thousands of tables and formatting that cannot be copied and pasted).
Also, on other printers you can see the lines seperating each row of the table. These lines are not visible on the HP print outs, even when the table is copied into a new document.
Has anyone come accross an issue like this before? Is there a way I can fix this without creating a new document? Do I need to get a new another new printer (the 4th printer this week!)?
Any advise, wise words would be greatly apprechiated!
Thanks!

Sorry, Fruhulda. After 4 hours on the phone with Apple care they are taking this issue further themselves. It seems to be a problem with our pages document and the compatibility with certain drivers. We have still not gotton to the bottom of it and Apple are going to get back to me when they have an answer.
We also worked out that the issue only happens when you print via Ethrenet & USB. Printing via Wifi is ok and there are no quality issues.
Very Strange!

[solved] Strange Audio Issue

I am experiencing a strange audio issue with my Intel-HDA ICH7:
# lspci -v
00:1b.0 Class 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 30a5
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access>
when I installed Arch linux the first time a mounth ago on this computer, I had a sound problem that was solved in a very strange way.
Everything worked fine until a week or so (I believe from Alsa 1.0.12). Now sometimes sound works and sometimes it doesn't. For example sometime I boot the computer and have no sound, then I reboot it without doing anything, and then sound works.
I have tried messing with the modprobe.conf:
# /etc/modprobe.conf (for v2.6 kernels)
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF version 1.0.11 ---
#alias snd-card-0 snd-hda-intel
#alias sound-slot-0 snd-hda-intel
# --- END: Generated by ALSACONF, do not edit. ---
#options snd-hda-intel model=F1734
options snd-hda-intel model=z71v
options snd-hda-intel position_fix=1
but it was useless. If I put back the modules in rc.conf everything is worse: sound doesn't work at all.
A diff between lsmod in a "working boot" and a "without sound boot" showed that the same modules where in kernel memory.
A diff between dmesg showed this difference:
< hda_intel: azx_get_response timeout, switching to single_cmd mode...
was present in the not working boot. This line is absent in a working boot dmesg.
The only way to make the sound card working everytime is to remove the snd* modules load from the boot sequence and load the modules "by hand" after the login.
Any ideas?
PS : If something is unclear due to my poor English please tell my and I'll try to explain it better.

phrakture wrote:snd-hda-intel is screwed up - on my thinkpad I had to go into the bios and enable the modem for sound to work. Oddly enough, the modem was off by default.
Also, mine has no PCM listed, I need to use "front" as my PCM level... not to mention the UI is way off with 'tpb' (if you have a thinkpad)
Yes it's not an Arch Linux related problem: I had problems with Debian (Etch and Sid based distros like ubuntu) too (but there I had no modprobe issue on the init sequence. Maybe is a problem of shared IRQs, but I have to study the existing documentation as I am a newbie). The difference is that Arch is simple enought for me to try something like modprobing "by hand" in the init sequence. PCM seems to work, however the volume is very low and I have found no way to make the mic work. Under Mepis I was able to make it work only if I plugged it in windows xp and then reboot into Linux. But I can't try it with Arch as I have erased the windows partition...
I will try the new kernel, study the documentation and then report. Hoping this will be usefull to others too.

Very strange backlight issue

I have a 600mhz (16 VRAM) iBook that I'm trying to fix for a friend. It has a strange backlight issue. Everytime the ibook is started, it chimes, and shows the screen (bright and perfect), but as soon as 9.2 starts to load, the backlight goes out. It is not intermittent, it happens at the exact same time every time I start it up (right when the progress bar starts to move). I reset the PRAM, which caused the computer to now look for a startup device, so all the extra time it takes search, the backlight is fine. Here's what I've tried.
In firewire mode, the backlight never comes on
With a hardware test disc, the backlight never comes on
Reset the PRAM (several times)
Reset the PMU (several times)
Any ideas out there?

As an update, I tried a Mac OS 10.4 startup disc which seemed to work, and the backlight came on with no problems. The machine did freeze on the welcome screen right after I selected english as the language of choice. So I tried a 10.3 disc which yeilds a kernal panic of "Unable to find driver for this platform: "PowerBook 4,3". After this, I tried a 9.2.2 disc which boots (takes 20 mins to boot) and when I try to load the installer I receive a "this program can not run on this machine", and it closes. This really seems like a strange problem. Any ideas?

Strange audiobooks issue

I have a strange audiobook issue. For background, I'm running iTunes 7.1.1 on Windows Vista Business, and have a 30GB video iPod.
Ok. I bought the audiobook of "The Great Gatsby" from iTunes. It is in my iTunes as an audiobook, is checked to sync and everything. Also, when my iPod is plugged in, and you expand the little arrow over in the left hand (so you can see what's actually ON the iPod, as opposed to in iTunes) and click on the Audiobooks under the iPod, it shows up, all three parts of the book.
However, when I look on my actual iPod, scroll to Audiobooks on the device, it's not there. But it says it's there (over iTunes) when it's plugged in.
Another audiobook, one that has been on there forever, apparently syncs just fine.
Anyone experience this?
(Please, for the love of Christ, don't anyone post on here and tell me that iTunes is not fully compatible with Vista. I know this. You know I know this.)

Ok, for anyone coming across this in the future.
I resolved this by changing up the way I was running the MovUser command a little bit.
Previously, I was using MoveUser with the -u option, it would migrate the mailboxes, as far as I could tell, successfully. Then I would update the mailhost ldap attribute myself.
I changed to using the -l option with an ldap url and -A to have MoveUser update ldap, and it seems to be working just fine.
Not sure why first command doesn't work though...

Really strange network issue that is specific to OS X 10.6.8

Really strange network issue that is specific to OS X 10.6.8 on both 2 iMacs and an older intel Mac Pro.
Any system running 10.6.8 is achieving on average 15 –20 mb a sec transfer rates regardless of drive speeds, cables, network activity etc.. I've spent some time removing any cable , drive speed, router issues to the point where one machine dual boots into both 10.6.8 and 10.6.5
The 10.6.5 system has network speeds of 60mb – 80mb p/sec transfer rates.
Our older 10.5.8 PPC mac gets 80mb and my 2011 Macbook Pro 10.7.2 hits 60mb – 80mb consistently as well.
Any idea what the cause is?
Cheers

Since your other Mac running 10.5.8 is not affected, you know that your AirPort router is functioning correctly.
What changed on your Mac? This seems like a post for either the Mac OS X v10.6 Snow Leopard support area, or the support area for your model of Mac.
We normally handle questions about the AirPort Express, AirPort Extreme or Time Capsule in this area, but you can certainly wait to see if you receive a response here.

HP Dm1-1102sa Strange charging issue

Hi,
My laptop (HP dm1-1102sa) has developed a strange charging issue. The laptop will initially charge fine then it will flick between being charging and running on battery constantly. I bought another battery to see if it was that but the problem still occurred. I then took it apart to check for loose connections and voltage. There were no loose connections and the pins on the battery terminals were showing a constant 18.5v. I tried running the laptop with out the battery and the laptop shutdown after a while.
Anyone have any ideas on what I can do next?
Thanks in advance.
Simon

Hi, thanks for the response, I had a look at this page and followed the suggestions, it all came up fine.
What I have noticed is the bi-coloured LED that sits next to the power connection on the left side was white which indicates not charging (so it seems) , even when it was at 73% and plugged in it wasn't charging, I removed the battery and gently blew out the plug and socket and re-connected the battery several times to see if it was a contact issue, I also did the same for the power connector.
The odd thing was it would run perfectly on battery and on mains just not charging.
I downloaded the latest bios revision (not yet installed), so I left it for a while with the battery and the mains lead disconnected, reconnected everything and noticed the bi-coloured LED was now orange so I left it on the desk for a while not running and when I did start it up some time later it was upto 95% charge and then stopped charging again, and again the LED was back to whte.
Today after receiving this message I tried the suggestions as per the document (except I pulgged in the mains first which brought up the orange LED), performed the tests, I had already tried the HP assistant battery test in windows which showed no issues (still wasn't charging, sitting at 73%), now with it running in front of me (not the computer I am using to type this response) the LED is still orange and the message I get now is "99% available (plugged in, charging)".
So for the moment it appears to have righted its self which is a concern, I hope that it stays this way....
JJ

Excise vs account reconciliation issue

Experts plz help me to know how to do Excise vs account reconciliation issue?

Hi,
Could you explain in brief what is the exact query?
Regards,
Hansa Chechani

Can't access root share sometimes and some strange performance issues

Hi :)
I'm sometimes getting error 0x80070043 "The network name cannot be found" when accessing \\dc01 (the root), but can access shares via \\dc01\share.
When I get that error I also didn't get the network drive hosted on that server set via Group Policy, it fails with this error:
The user 'W:' preference item in the 'GPO Name' Group Policy Object did not apply because it failed with error code '0x80070008 Not enough storage is available to process this command.' This error was suppressed.
The client is Windows Server 2012 Remote Desktop and file server is 2012 too. On a VMware host.
Then I log off and back on, and no issues.
Maybe related and maybe where the problem is: When I have the issue above and sometimes when I don't (the network drive is added fine) I have some strange performance issues on share/network drive: Word, Excel and PDF files opens very slowly. Offices says
"Contacting \\dc01\share..." for 20-30 sec and then opens. Text files don't have that problem.
I have a DC02 server also 2012 with no issues like like this.
Any tips how to troubleshoot?

Hi,
Based on your description, you could access shares on DC via
\\dc01\share. But you couldn’t access shares via \\dc01.
Please check the
Network Path in the Properties of the shared folders at first. If the network path is
\\dc01\share, you should access the shared folder by using
\\dc01\share.
And when you configure
Drive Maps via domain group policy, you should also type the Network Path of the shared folders in the
Location edit.
About opening Office files very slow. There are some possible reasons.
File validation can slow down the opening of files.
This problem caused by the issue mentioned above.
Here are a similar thread about slow opening office files from network share
http://answers.microsoft.com/en-us/office/forum/office_2010-word/office-2010-slow-opening-files-from-network-share/d69e8942-b773-4aea-a6fc-8577def6b06a
For File Validation, please refer to the article below,
Office 2010 File Validation
http://blogs.technet.com/b/office2010/archive/2009/12/16/office-2010-file-validation.aspx
Best Regards,
Tina

Strange power issues

I am having some strange power issues with my six week old Macbook. The symptoms are as follows (I apologise in advance for the length of this post) :
1) If the battery charge is below 50%, and you connect the magsafe charger prior to power-on, the charge light will illuminate until the grey boot screen comes up. Then the charge light turns of completely & the Macbook boots up using battery power. If I disconnect the magsafe connector, followed by the mains and reconnect in the reverse sequence, the light turns green momentarily and then orange (as it should for charging)
2) If I start the coconutBattery application after booting into OSX, while the charge is still below 50%, the same issue occurs again with the magsafe. It appears to happen at the exact time the application queries the battery. I can get the charger working if I follow the same disconnect/mains/reconnect sequence.
3) The issues above also seems to occur when the battery updater checks the battery. The Macbook does not recognise that the charger is plugged in.
4) If the charge is above 50%, then all works as expected. The coconutBattery application does not affect the charger. The Macbook works as normal.
I have tested with a brand new magsafe & a new battery - symptoms are identical. I have noticed several other non-consistent issues - the flashing green light/orange light on the magsafe connection, unusual battery life calculations (70+ hours).
I have performed calibrations & reset the PMU and the PRAM, and have all current updates. And I have spent a large amount of time in the forums looking at similar issues without much success. I am beginning to suspect the logic board (DC chip) is at fault, however I dont relish the idea of dropping my new Macbook at my local Apple Repair centre & getting it back three weeks later with the same issue.
My current cycles (on this new battery) are at 2 with a full charge capacity of 5142 mAh.
My questions to the community are:
Does anyone have a similar experience with these types of symptoms?
Or can someone illustrate on what would cause the Macbook to believe that the magsafe was disconnected? Whatever internal system call the coconutBattery application uses to recover details from the battery appears to trigger this behavior.
I would appreciate any thoughts on this one.
Macbook Core 2 Duo - 2GB RAM Mac OS X (10.4.9)

Just another observation, based on reading some of Apple's documentation regarding the AC charger:
"If the adapter works after this 60-second "rest," you most likely have a line noise issue with your power source that will require you to reset the adapter (by repeating this moment of rest) periodically. This happens when the AC adapter's over voltage protection feature senses ground noise and then turns off the adapter."
Could a sudden draw of power required at a 50% and below charge trip this over voltage protection feature? I know the charging draw varies based on current battery level.
I have tested this in UPS protected boards with the same result.

Strange Database issues while trying to create new user through EM...

I'm attempting to configure my local Oracle 11g database in order to create a Content Server user in order to setup a Fatwire installation. I'm getting some strange issues with my database that I was hoping maybe someone could help me out with.
The guide I'm following starts with this:
+1. Determine the Console Server port:+
a. Open the emoms.properties file in a text editor. The file is located in:
+<ora_home>/<servername>_<SID>/sysman/config/+
b. Find the line,
oracle.sysman.emSDK.svlt.ConsoleServerPort
and make a record of the port number value at the end of the line.
When I open the emoms.properties file in Notepad++, I'm unable to read the contents - it's all symbols/jibberish.
The next step says this:
+2. Log in to the Oracle Enterprise Manager console:+
a. Execute the following command: emctl status dbconsole
When I execute that command I get the following error:
Environment variable ORACLE_UNQNAME not defined. Please set ORACLE_UNQNAME to database unique name.
The third step says this:
Open a browser and go to the URL highlighted in bold in step a above. If you see
a “Security Mismatch” error, ignore it (the error appears if you are using a selfsigned
certificate).
I skipped to this step because I'm assuming the link it wants me to go to is my EM console (https://localhost:1158/em/console/aboutApplication), however when I browse to that URL I get the following error:
503 Service Unavailable
Service is not initialized correctly. Verify that the repository connection information provided is correct.
Clearly, something isn't right here. What's going on? Any help would be appreciated.

Alfonso Vicente wrote:
Did you try what I suggested?Yes, thanks for the advice. Now I'm having some additional issues. When I run emctl status dbconsole I get the following error:
OC4J Configuration issue. C:\app\john.smith\product\11.2.0\dbhome_1/oc4j/j2ee/OC4
J_DBConsole_ORCL-SMITH.company.com_localhost_orcl not found.
This is appearing after I made the appropriate changes to the emoms.properties file and set ORCL_UNQNAME to "localhost_orcl" <-- is that correct? the path to my emoms.properties is:
C:\app\john.smith\product\11.2.0\dbhome_1\localhost_orcl\sysman\config
Here is my emoms.properties file, does this look right?
#Mon Mar 19 17:56:05 EDT 2012
oracle.sysman.emSDK.svlt.ConsoleServerName=localhost\:1158_Management_Service
oracle.sysman.eml.mntr.emdRepPwd=2ad171ddf6ce91aebf1c2f2c371ee5a315591a1be21f37965a88d54126d7528aa1091f543569e58b
emdrep.ping.pingCommand=/bin/ping -c 3 -w 30 <hostname>
em_oob_shutdown=false
LargeRepository=false
oracle.sysman.eml.mntr.emdRepPort=1521
em_email_address=
oracle.sysman.eml.mntr.emdRepPwdSeed=8622625238442107993
em_oob_crash=false
em.oms.dumpModules=omsThread,repos
oracle.sysman.emRep.dbConn.statementCacheSize=50
oracle.sysman.db.isqlplusUrl=%ISQLPLUS_PROTOCOL%\://%ISQLPLUS_HOST%\:%ISQLPLUS_PORT%/isqlplus/dynamic
em_oob_startup=false
oracle.sysman.emSDK.svlt.ConsoleServerPort=4889
em_from_email_address=_NOT_AVAILABLE_
oracle.sysman.eml.mntr.emdRepPwdEncrypted=TRUE
oracle.sysman.db.isqlplusWebDBAUrl=%ISQLPLUS_PROTOCOL%\://%ISQLPLUS_HOST%\:%ISQLPLUS_PORT%/isqlplus/dba/dynamic
oracle.sysman.emSDK.svlt.ConsoleServerHost=localhost
em_from_email_name=_NOT_AVAILABLE_
oracle.sysman.emSDK.svlt.ConsoleServerHTTPSPort=1159
em_email_gateway=
oracle.sysman.eml.mntr.emdRepServer=localhost
oracle.sysman.eml.mntr.emdRepSID=NO_VALUE
oracle.sysman.eml.mntr.emdRepConnectDescriptor=(DESCRIPTION\=(ADDRESS_LIST\=(ADDRESS\=(PROTOCOL\=TCP)(HOST\=localhost)(PORT\=1521)))(CONNECT_DATA\=(SERVICE_NAME\=orcl)))
oracle.sysman.emkeyfile=C:\app\john.smith\product\11.2.0\dbhome_1\localhost_orcl\sysman\config\emkey.ora
em.ip.ui.enable=true
oracle.sysman.eml.mntr.emdRepUser=sysman
oracle.sysman.emSDK.svlt.PublicServletEnabled=true

Strange keyboard issue on a Satellite P300

Hi,
Since a week i have a problem with my keyboard on my P300.
The keyboard doesn't work when the power supply is on. The keyboard is inactive on vista and in the BIOS.
When i cut the power and the PC is on battery the keyboard is OK.
Do you have any infomations about this problem ?
Thanks.
oliv

Hi Oliv
Such issue is not known to me and I think it must be hardware related issue.
What you can do about it? Not much except to try with BIOS update but I dont think it will help.
Satellite P300 is not the newest notebook model. Since when you have noticed such strange keyboard behaviour?
To be honest I think you should contact Toshiba service in your country. Let them check keyboard and keyboard controller using diagnostic tools. They can tell you what the problem is and how to fix it.

Strange reconciliation issue

Similar Messages

Maybe you are looking for