Strange USB mount error: Solved

when I plug in my SD card reader I get the following message.
It works as root and the last time I tried it worked as user.
Using KDE and testing.
solved by adding my user to the storage group
A security policy in place prevents this sender from sending this message to this recipient, see message bus configuration file (rejected message had interface "org.freedesktop.Hal.Device.Volume" member "Mount" error name "(unset)" destination "org.freedesktop.Hal")
I did a more careful forum search.
:oops:

ataraxia wrote:
You have no swap configured? Konqueror and Firefox are both huge memory hogs. You could easily use all your memory doing ordinary things (especially if you use KDE or other large things).
Configure some swap. If you have no free partitions, but a little free space, you can swap to a file: http://www.netadmintools.com/art1.html I suggest at least 1 GB of swap.
a was forgoten activate the swap .
1 0x00 1 1 0 0x83 254 63 1023 63 20000862
2 0x00 254 63 1023 0x83 254 63 1023 20000925 80003700
3 0x00 254 63 1023 0x82 254 63 1023 100004625 996030 << that is the swap
4 0x00 254 63 1023 0x83 254 63 1023 101000655 524136690
thankz
PD: sorry for my english

Similar Messages

Cifs mount error(56): Invalid request code

I am trying to cifs mount my Arch server (called server) to an SMB disk on a router (experia). This keeps throwing me error messages. Invalid request code.
So I decided to test this on my Arch client (called kastje). Same issue:
[david@kastje ~]$ sudo mount -v -t cifs //experia/testshare /mnt/temp -o username=testuser,password=testpass
mount.cifs kernel mount options: ip=192.168.178.1,unc=\\experia\testshare,user=testuser,pass=********
mount error(56): Invalid request code
Refer to the mount.cifs(8) manual page (e.g. man mount.cifs)
However, mounting through gvfs-smb (PCmanFM) works fine, so it seems that both my client and the router are configured correctly but I am failing at using mount.cifs. But I just cannot find out what. Searching for the mount error(56) turns up some result but none are really helpful, as they do not solve the issue .
I hope someone can point me in the right direction.

From my fstab:
//Server/Shares /mnt/Shares cifs guest,uid=1000,x-systemd.automount,iocharset=utf8,file_mode=0777,dir_mode=0777 0 0
//Server/Homes /home/pat/Server cifs credentials=/home/pat/.smbcredentials,x-systemd.automount,iocharset=utf8,sec=ntlm 0 0
Does your router have a smb.conf? Or, I should be asking, is a samba server running on your router? You may find that an NFS share might work better than samba, especially if you don't have a setup like mine.

Mount Error Message

Hello, when I plug in my USB stick, thunar-volman throws up this error:
A security policy in place prevents this sender from sending this message to this recipient, see message bus configuration file (rejected message had interface "org.freedesktop.Hal.Device.Volume" member "Mount" error name "(unset)" destination "org.freedesktop.Hal")
I haven't changed any of the files in /etc/dbus-1/
I belong to the following groups:
disk wheel games dbus hal network video audio optical storage scanner users shutdown
Much appreciated, thanks.
Last edited by Manifold (2007-01-28 21:54:01)

i also tried this how to
the cd work good but not the usbstick
fdisk -l
Disk /dev/sda: 120.0 GB, 120033041920 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 2550 20482843+ 7 HPFS/NTFS
/dev/sda2 14533 14593 489982+ 82 Linux swap / Solaris
/dev/sda3 2551 13579 88590442+ f W95 Ext'd (LBA)
/dev/sda4 14047 14532 3903795 83 Linux
/dev/sda5 2551 13324 86542123+ 7 HPFS/NTFS
/dev/sda6 13325 13579 2048256 b W95 FAT32
Partition table entries are not in disk order
Disk /dev/sdb: 254 MB, 254803968 bytes
16 heads, 32 sectors/track, 972 cylinders
Units = cylinders of 512 * 512 = 262144 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 972 248816+ 6 FAT16
Last edited by dids22 (2007-02-21 23:54:20)

Disk image could not be mounted - error

Ok, I've been using TC (Time Capsule) for a week now, and it was working great. Then in the middle of the week I decided to change the password for TC. Now when I reboot my iMac, TM (Time Machine) will not back up and it gives me a failed - "the backup disk image could not be mounted" error. Then if I go to the AirPort Utility and reboot TC, all of the sudden TM works. Couple of days go by and when I reboot the iMac again, I have to do the whole process again of rebooting TC to get TM to work. Has anyone encountered this issue? I think I explained it well...

This happened to me too.
I called Apple (they'll talk to you for 90 days after you buy your Time Capsule and solve all your problems.)
The solution was to rename the Time Capsule. Here's how:
Open Time Capsule in System Preferences, click on Change Disk, and choose None from the list.
Open Airport Utility (choose Go from the Finder Menu, choose Utilities from the list, then Airport Utility), highlight your Time Capsule when its picture appears in the left side bar. Click Manual Setup in the main window, then the Disk icon on the top. Highlight the lower of the two names Time-Capsule Disk and change it to something short and one word, like Disk. Click Update, then close Airport Utility after your Time Capsule restarts.
Go back to Time Capsule Preferences and click on the Choose Disk button in the center of the main part of the window, then choose your newly-named Time Capsule (If you see more than one Time Capsule name there, restart your computer first).
This solved it for me. The guy on the phone said that in the tech help people's experience the Time Machine program doesn't like long names or ones with "higher" ascii characters in them.
Good luck.
jmb

Error:metricsCCBasebandReset { reason: "modem reset: USB Fatal Error: Interface is inactive(Select Exception)"

Hi,
I m having troubles with my iphone 4s since day one of its activation: status bar displays searching every now and then, and i m loosing a lot of calls.
I have upgraded the ios to the 9A406 but this did not solve it.
i knew how to get the logs : Settings ==> About ==> Diagnostics & Usage ==> Diagnostic & Usage Data ==> and then check the awdd log.
and found it to be related to a modem reset error logged as follow:
deviceId: "546356ff6e1e8289929f00ec8dd48f4c20b5a9f7"
isAnonymous: true
deviceConfigId: 101
triggerTime: 1326539111279
triggerId: 524310
profileId: 10129
investigationId: 0
metricsCCBasebandReset {
reason: "modem reset: USB Fatal Error: Interface is inactive(Select Exception)"
inVoiceCall: false
rat: 1
PLMN: "60201"
timestamp: 1326539111279
I have plenty of logs like this:
If someone managed to get this fixed, thanks to advice what was performed??

Same with me on iOS 5.1.1

Audio usb ALSA error: No suitable mixer element found

Hello everybody.
I've installed arch last week. I've some problem with my usb audio. The audio usb device works but i can't use a mixer, so audio control is everytime set on max.
I can't use my normal intel audio 'cause is broken. This is my aplay -l output:
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC268 Analog [ALC268 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: ALC268 Digital [ALC268 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: AUDIO [USB AUDIO], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
When i try to play audio files on audacious, arch give me following error: Audio usb ALSA error: No suitable mixer element found.
I've set the audio usb device as default with asoundconf. If i try to use hd intel audio, the mixer works good, but when i get back to usb audio, mixer is absent. There is a way to set a mixer for the usb audio device?
Last edited by Kalamaius (2014-05-23 14:34:13)

emeres wrote:
As for the usb sound card I would try setting those parameters:
autoclock=0/1
ignore_ctl_error=0/1
Kalamaius wrote:Intel audio is broken, I've a crackling sound all time. I changed the previous sound card but the new one that my personal computer technician mounted never works properly, isn't a new card but a used one.
Probably related to module options.
If you simply want to control the volume it would be easy to implement a softvol plugin. But this headset should have a volume control. What is the output of:
tree /proc/asound
tree /proc/asound
/proc/asound
├── AUDIO -> card1
├── card0
│   ├── codec#0
│   ├── codec#1
│   ├── id
│   ├── pcm0c
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── prealloc
│   │   ├── prealloc_max
│   │   ├── status
│   │   └── sw_params
│   ├── pcm0p
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── prealloc
│   │   ├── prealloc_max
│   │   ├── status
│   │   └── sw_params
│   ├── pcm1p
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── prealloc
│   │   ├── prealloc_max
│   │   ├── status
│   │   └── sw_params
│   ├── pcm6c
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── prealloc
│   │   ├── prealloc_max
│   │   ├── status
│   │   └── sw_params
│   └── pcm6p
│   ├── info
│   └── sub0
│   ├── hw_params
│   ├── info
│   ├── prealloc
│   ├── prealloc_max
│   ├── status
│   └── sw_params
├── card1
│   ├── id
│   ├── pcm0c
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── status
│   │   └── sw_params
│   ├── pcm0p
│   │   ├── info
│   │   └── sub0
│   │   ├── hw_params
│   │   ├── info
│   │   ├── status
│   │   └── sw_params
│   ├── stream0
│   ├── usbbus
│   ├── usbid
│   └── usbmixer
├── cards
├── devices
├── hwdep
├── Intel -> card0
├── modules
├── oss
│   ├── devices
│   └── sndstat
├── pcm
├── seq
│   └── drivers
├── timers
└── version
20 directories, 63 files

Bugcode-usb-driver error

System: windows 8.1 Every day, sometimes a couple of times a day, the pc shuts down and restarts. A couple of times a week, i get the message,Error : Bugcode-usb-driver
What do I do to resolve this problem please. I've tried to search out the answer but would feel more confident with the expert guidance.
thank you

Hello @jjwalters,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you are getting the Bugcode-usb-driver error on your computer running Windows 8.1 and are seeking assistance, I would be happy to assist you, but first I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As with this I can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Please re-post with the requested information and I would be happy to provide you with assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Strange system log error from Photoshop CS4

Hi.
I keep getting this strange system log error from Photoshop CS4.
It comes after a wile when using PS CS4.
I tried to chance the memory settings and scratch disc to see if that helped. It didn't.
I also checked all my ram for anything bad. 16GB in my Mac Pro Intel OS X 10.5.6
Everything is updated to latest included Adobe apps.
This is the system log error
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** set a breakpoint in malloc_error_break to debug
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: Adobe Photoshop CS4(305,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 7 16:04:03 mugge [0x0-0x28028].com.adobe.Photoshop[305]: *** error: can't allocate region
And it keeps on until i close Photoshop.
Please anybody ?? i cant figure out what this means.
Thx for help.
Erik S

Now i get this system log error ?
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: Adobe Photoshop CS4(651,0x6a73720) malloc: *** mmap(size=132911104) failed (error code=12)
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** error: can't allocate region
Apr 29 14:45:02 mugge [0x0-0x32032].com.adobe.Photoshop[651]: *** set a breakpoint in malloc_error_break to debug
and this from Bridge ???
Apr 29 16:35:45 mugge Adobe Bridge CS4[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0x29777980: double free\n*** set a breakpoint in malloc_error_break to debug
Apr 29 16:35:45 mugge Adobe Bridge CS4[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0xcb73827b: Non-aligned pointer being freed\n*** set a breakpoint in malloc_error_break to debug
Apr 29 16:35:45 mugge Adobe Bridge CS4[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0x29777980: Non-aligned pointer being freed (2)\n*** set a breakpoint in malloc_error_break to debug
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0x29777980: double free
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: *** set a breakpoint in malloc_error_break to debug
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0xcb73827b: Non-aligned pointer being freed
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: *** set a breakpoint in malloc_error_break to debug
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: Adobe Bridge CS4(650,0xb0e8f000) malloc: *** error for object 0x29777980: Non-aligned pointer being freed (2)
Apr 29 16:35:45 mugge [0x0-0x31031].com.adobe.bridge3[650]: *** set a breakpoint in malloc_error_break to debug
Chris. also read my post just before this one plase. thx

USB Power Error with iPod Touch and 2012 MBA

I am getting a USB power error when I connect my current generation 32 GB iPod touch to my 2012 MBA.
Since both iPod and MacAir are running current software. I am also starting to get errors from iTunes telling me that my iPod can not be accessed. Any ideas? Mac or iPod problem, or BOTH? Closest Apple store is 250 miles away, but MBA is still under original 1 year original warranty. Might be time for a visit.

If a 5G iPod,
Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.

Mount error when installing xcode 3 and iOS 4

Hi,
I ran into mount error when installing xcode 3.2.6 and iOS 4.3 downloaded from https://developer.apple.com/devcenter/download.action?path=/Developer_Tools/xcod e_3.2.6_and_ios_sdk_4.3__final/xcode_3.2.6_and_ios_sdk_4.3.dmg.
I work on Mac mini with Mac OS X 10.6.
Could anyone help? Thanks!
Regards,
Emily

Hi Ken,
Thanks for your advice! I would try to clean up for more free space. I just downloaded one dmg from another website linking to apple. I could successfully install that one, but very often the content in gdb window is empty. Even if the gdb works for some time initially, after loading some specific project, the gdb doesn't provide info any longer :-( Any idea?
It might be the best season in Shenzhen now. It is sunny, but not hot, with temperature from 25 degree centigrade to 30.
Regards,
Emily

Make USB mount read only.

Hello again,
I am looking to make any USB mounted devices read only by default. Is there a way to do this in Leopard?

Greetings,
While you can make a USB device read only, you can't make a port read only. There are ways to disable a USB port, but that's about it.
You can also use a OS X Server and with it, you can deny access to the device, but to make it (the port) read only, I don't think that's possible with any OS. You could mark the internal hard drives read only, as well, but that would be a major pain.
I have hundreds of machines, and the open labs are the only ones I disallow the use of USB devices for security reasons, PeeCee or Mac. Using the OS X Server, we can apply restrictions, as I do with Active Directory for the PeeCees.
Cheers,
M.

Mount error when mounting Windows Server share

Trying to mount a share on a Windows Server I have in my home.
When I use:
smbclient -L SERVERNAME -U administrator
and I enter the password after the prompt
It returns a list of all the shares in the server like so:
Domain=[SERVERNAME] OS=[Windows Server 2003 3790 Service Pack 2] Server=[Windows Server 2003 5.2]
Sharename Type Comment
SHARE1 Disk Shared folder
SHARE2 Disk Shared folder
SHARE3 Disk Shared folder
Domain=[SERVERNAME] OS=[Windows Server 2003 3790 Service Pack 2] Server=[Windows Server 2003 5.2]
Server Comment
Workgroup Master
but when I try to mount of the shares with
# mount -t cifs //SERVERNAME/SHARE1 /mnt/mountpoint -o user=administrator,password=password
it returns an error
mount error: could not resolve address for SERVERNAME: Unknown error
Am I doing something wrong?
Thanks,

the SERVERNAME in these commands is a netbiosname and can differ from the hostname.
Smbclient seems to use it's own method to resolve netbiosnames, possibly the mount command uses a different method.
Try the mount command with the ip-address of the server instead of SERVERNAME to verify mounting the share works.
If the share can be mounted by //ip-address/SHARE1 , you may need additional options for the mount command to make netbios name resolution work correctly.
check man mount.cifs .
edit : typo's
Last edited by Lone_Wolf (2013-08-10 12:40:47)

ASM Disk Mount Error

Hi,
I am consistently getting the following error since yesterday while mounting the ASM disk.
1. I created the ASM disks successfully and created the appropriate ASM DiskGroups using asmca utility.
2. I was able to see the diskgroups as mounted from asmcmd tool.
3. All of a sudden, all the diskgroups were dismounted yesterday and I see the following error in the alert logs for all the
diskgroups.
4. This is using ASM11g
As I exhausted all my avenues to fix, I have turned to you for further assistance. Please do the needful.
SQL> /* ASMCMD */ALTER DISKGROUP DataVSPSI MOUNT
NOTE: cache registered group DATAVSPSI number=3 incarn=0x7934bf5d
NOTE: cache began mount (first) of group DATAVSPSI number=3 incarn=0x7934bf5d
NOTE: Assigning number (3,0) to disk (ORCL:D01_VSP_SI)
Thu Dec 27 17:38:29 2012
NOTE: start heartbeating (grp 3)
kfdp_query(DATAVSPSI): 11
kfdp_queryBg(): 11
NOTE: cache opening disk 0 of grp 3: D01_VSP_SI label:D01_VSP_SI
NOTE: F1X0 found on disk 0 au 2 fcn 0.0
NOTE: cache mounting (first) external redundancy group 3/0x7934BF5D (DATAVSPSI)
NOTE: starting recovery of thread=1 ckpt=2.1 group=3 (DATAVSPSI)
WARNING: IO Failed. group:3 disk(number.incarnation):0.0xeae44fae disk_path:ORCL:D01_VSP_SI
AU:4 disk_offset(bytes):4333568 io_size:122880 operation:Read type:asynchronous
result:I/O error process_id:32162
WARNING: IO Failed. group:3 disk(number.incarnation):0.0xeae44fae disk_path:ORCL:D01_VSP_SI
AU:4 disk_offset(bytes):4202496 io_size:131072 operation:Read type:asynchronous
result:I/O error process_id:32162
ORA-15080: synchronous I/O operation to a disk failed
ERROR: ASM recovery failed to read ACD
NOTE: cache initiating offline of disk 0 group DATAVSPSI
NOTE: process 32162 initiating offline of disk 0.3940831150 (D01_VSP_SI) with mask 0x7e in group 3
WARNING: Disk D01_VSP_SI in mode 0x7f is now being taken offline
NOTE: initiating PST update: grp = 3, dsk = 0/0xeae44fae, mode = 0x15
kfdp_updateDsk(): 12
kfdp_updateDskBg(): 12
ERROR: too many offline disks in PST (grp 3)
WARNING: Disk D01_VSP_SI in mode 0x7f offline aborted
Thu Dec 27 17:38:29 2012
NOTE: halting all I/Os to diskgroup DATAVSPSI
NOTE: crash recovery signalled OER-15130
ERROR: ORA-15130 signalled during mount of diskgroup DATAVSPSI
NOTE: cache dismounting (clean) group 3/0x7934BF5D (DATAVSPSI)
NOTE: lgwr not being msg'd to dismount
NOTE: cache dismounted group 3/0x7934BF5D (DATAVSPSI)
Also, I think the lower level disk is fine as I am able to write to the disk as follows :
[oracle@rmanqa01 trace]$ dd of=/dev/sdp1
Test Test
0+1 records in
0+1 records out
10 bytes (10 B) copied, 4.97435 seconds, 0.0 kB/s
[oracle@rmanqa01 trace]$ id
uid=500(oracle) gid=500(oinstall) groups=6(disk),500(oinstall),501(dba),502(oper),503(asmadmin),504(asmdba),505(asmoper),506(horcm)
[oracle@rmanqa01 trace]$ ls -l /dev/sdp1
brw-rw---- 1 root disk 8, 241 Dec 28 11:59 /dev/sdp1
[oracle@rmanqa01 trace]$
The oracleasm also lists the disk D01_VSP_SI as follows :
[root@rmanqa01 log]# /etc/init.d/oracleasm listdisks
A01_VSP_SI
ADSK01
ARCH_AMS_SI
D01_VSP_SI
DATA_AMS_SI
DDSK01
DEMO_ARCH
DEMO_DATA
L01_VSP_SI
RDSK01
REDO_AMS_SI
You have new mail in /var/spool/mail/root
[root@rmanqa01 log]# /etc/init.d/oracleasm querydisk D01_VSP_SI
Disk "D01_VSP_SI" is a valid ASM disk
[root@rmanqa01 log]#
kfed tool was giving proper data till yesterday.
Today, I am getting the following :
./kfed read /dev/oracleasm/disks/D01_VSP_SI
kfbh.endian: 84 ; 0x000: 0x54
kfbh.hard: 101 ; 0x001: 0x65
kfbh.type: 115 ; 0x002: *** Unknown Enum ***
kfbh.datfmt: 116 ; 0x003: 0x74
kfbh.block.blk: 1936020512 ; 0x004: T=0 NUMB=0x73655420
kfbh.block.obj: 2147486324 ; 0x008: TYPE=0x8 NUMB=0xa74
kfbh.check: 2886846267 ; 0x00c: 0xac11c73b
kfbh.fcn.base: 0 ; 0x010: 0x00000000
kfbh.fcn.wrap: 0 ; 0x014: 0x00000000
kfbh.spare1: 0 ; 0x018: 0x00000000
kfbh.spare2: 0 ; 0x01c: 0x00000000
ERROR!!!, failed to get the oracore error message
[oracle@rmanqa01 bin]$
Please help.
Thanks
V V
Edited by: user13479556 on Dec 28, 2012 12:00 PM

Thanks Berx for pointing that out.
I deleted the ASM disks and the diskgroups and re-created a fresh and was able to start the ASM instance and mount the DGs.
Now the mount is persistent, but the dbca fails with the following error in the alert log. Under what situations can this error be seen ?
NOTE: Loaded library: System
SUCCESS: diskgroup DATAAMSSI was mounted
SUCCESS: diskgroup ARCHAMSSI was mounted
ERROR: failed to establish dependency between database R3AMSSI and diskgroup resource ora.DATAAMSSI.dg*ERROR: failed to establish dependency between database R3AMSSI and diskgroup resource ora.ARCHAMSSI.dg*Mon Dec 31 20:25:25 2012
SUCCESS: diskgroup LOGAMSSI was mounted
Mon Dec 31 20:25:25 2012
ERROR: failed to establish dependency between database R3AMSSI and diskgroup resource ora.LOGAMSSI.dg
Mon Dec 31 20:25:25 2012
Successful mount of redo thread 1, with mount id 784925673
Completed: Create controlfile reuse set database "R3AMSSI"
MAXINSTANCES 8
MAXLOGHISTORY 1
MAXLOGFILES 16
MAXLOGMEMBERS 3
MAXDATAFILES 100
Datafile
'+DATAAMSSI/R3AMSSI/system01.dbf',
'+DATAAMSSI/R3AMSSI/sysaux01.dbf',
'+DATAAMSSI/R3AMSSI/undotbs01.dbf',
'+DATAAMSSI/R3AMSSI/users01.dbf'
LOGFILE GROUP 1 ('+LOGAMSSI/R3AMSSI/redo01.log') SIZE 51200K,
GROUP 2 ('+LOGAMSSI/R3AMSSI/redo02.log') SIZE 51200K,
GROUP 3 ('+LOGAMSSI/R3AMSSI/redo03.log') SIZE 51200K RESETLOGS
Stopping background process MMNL
Stopping background process MMON
Starting background process MMON
Starting background process MMNL
Mon Dec 31 20:25:28 2012
MMON started with pid=17, OS id=10452
ALTER SYSTEM enable restricted session;
Mon Dec 31 20:25:28 2012
MMNL started with pid=18, OS id=10454
alter database "R3AMSSI" open resetlogs
RESETLOGS after incomplete recovery UNTIL CHANGE 945183
Errors in file /u01/app/oracle/diag/rdbms/r3amssi/R3AMSSI/trace/R3AMSSI_ora_10434.trc:
ORA-00313: open failed for members of log group 1 of thread 1
ORA-00312: online log 1 thread 1: '+LOGAMSSI/r3amssi/redo01.log'
ORA-17503: ksfdopn:2 Failed to open file +LOGAMSSI/r3amssi/redo01.log
ORA-15173: entry 'redo01.log' does not exist in directory 'r3amssi'
Errors in file /u01/app/oracle/diag/rdbms/r3amssi/R3AMSSI/trace/R3AMSSI_ora_10434.trc:
ORA-00313: open failed for members of log group 1 of thread 1
ORA-00312: online log 1 thread 1: '+LOGAMSSI/r3amssi/redo01.log'
ORA-17503: ksfdopn:2 Failed to open file +LOGAMSSI/r3amssi/redo01.log
ORA-15173: entry 'redo01.log' does not exist in directory 'r3amssi'
Mon Dec 31 20:25:29 2012
Checker run found 5 new persistent data failures
Mon Dec 31 20:27:07 2012
I can verify from asmcmd that the redologs mentioned above as missing is very much present in '+LOGAMSSI/R3AMSSI'
Thanks
V V

Strange ORA-01044 error

Hi Guys,
I'm getting a very strange ORA-01044 error:
Oracle.DataAccess.Client.OracleException ORA-01044: size 87160000 of buffer bound to variable exceeds maximum 288212783965667328 at Oracle.DataAccess.Client.OracleException.HandleErrorHelper(Int32 errCode, OracleConnection conn, IntPtr opsErrCtx, OpoSqlValCtx pOpoSqlValCtx, Object src, String procedure)*
at Oracle.DataAccess.Client.OracleException.HandleError(Int32 errCode, OracleConnection conn, String procedure, IntPtr opsErrCtx, OpoSqlValCtx pOpoSqlValCtx, Object src)*
at Oracle.DataAccess.Client.OracleCommand.ExecuteNonQuery()
As you can see, the buffer size does not exceed the maximum stated, yet it is still causing an exception.
Some background.. A new parameter has been added to a stored proc that was originally working fine, this new parameter is an associative array of numbers.
On the ODP.Net side, I create a parameter that has a collection type of "*PLSQLAssociativeArray*" and Oracle DB Type of "*Int32*".
Any ideas as to what might be causing this problem?

Hi,
What db version?
There is an older bug where this error would be raised if the requested buffer size exceeded the granule size of the SGA. That was from the 9.2 timeframe as I recall.
Regards,
Mark

Mount error: ...not superuser and mount.cifs not installed SUID

I'm trying to automount Samba shares but get this everytime I try to mount the partition:
mount error: permission denied or not superuser and mount.cifs not installed SUID
I have this entry in the fstab:
//192.168.2.1/Capsule /media/capsule cifs auto,noserverino,username=xxx,password=xxx,workgroup=WORKGROUP,iocharset=utf8,file_mode=0777,dir_mode=0777,suid,users 0 0
I tried different options (suid,users or without them) same results.
I also tried to chown like this:
chmod u+s mount.cifs
But still no luck
Need help please.

It seems that mount.cifs will only let you mount at directory that you are the owner of. I think this may be changeable with the UID option but I have not figured it out.

Strange USB mount error: Solved

Similar Messages

Maybe you are looking for