Stream7 - bluetooth audio streaming goes off when i turn the display off!
I have a hp stream 7 that is connected via bluetooth to my loudspeakers.
Everything is fine until the display turns off or i press the power butten to turn off the display.
When i turn on the display(press power button) the sound starts and play normally.
I can't find any option to turn off this behaviour in w8.1. Can you help?
The microsoft music player that is on the tiles metro section of windows supports music playback when the connected standby is activated. Unfortunatly if you are looking to go any further than this you will need to change over all your power control settings to that of a laptop.
I instructed another user of it in this post here, http://h30434.www3.hp.com/t5/Windows-Tablets/Stream-7-Can-t-Turn-off-screen-without-putting-tablet-i...
Similar Messages
-
When I take a picture with my iphone 4 and the flash is on I get a blue flash and a big blue screen with no pic. When I turn the flash off the pics come out
fine. I turn the flash on to take a pic in low light I just get a blue screen. How do I remedy this?Try a reset or restart of the device.
If that doesn't work attempt a restore of the phone's iOS -
I have to reenter my Wifi password every time I restart my Ipod touch. It used to retain the password but now it drops out when I turn the Ipod off. Any suggestions?
Try:
ipod touch wont remember wifi password: Apple Support Communities
Also, have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"? -
The light on the back of my phone will not turn off, even when I turn the phone off. Help?
The light on the back of my iphone 4s will not turn off. Even when I turn the phone off the light stays on. Can someone help? I did notice that the camera on the back has a little bit of moisture. (I have 3 small kids).
You will need to have the hold switch replaced.
-
Unmute not working model 4S
My iphone 4S has mute activated. It will not un-mute by taping the mute button or when I turn the phone off then back on.Hi Lukeohiggins,
If you are having issues with your iPhone unexpectely powering off, you may want to try the troubleshooting listed under Power/Battery > Will not turn on, will not turn on unless connected to power, or unexpected power off in the following article:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Cheers,
- Brenden -
My iPad iTunes store isn't working.. When I add a wifi I can't get into any websites and when I turn the wifi off I can but without wifi I can't download on iTunes :/
Ashotiffo wrote:
My iPad iTunes store isn't working.. When I add a wifi I can't get into any websites and when I turn the wifi off I can but without wifi I can't download on iTunes :/
When you add a WiFi you can't get into any websites??? But if you turn WiFi off you can access websites?
You can access websites without WiFi? Do you have a 3G/4G iPad? -
I can't get iPad off. It is like in a loop. When I held the on/off button and swipe it just does nothing.
Try rebooting your iPad. Press and hold BOTH the power and home buttons at the SAME time for at least 10 seconds (ignore the red slider to shut down) until the Apple Logo appears, then let go of both buttons and your iPad will restart. See if you can shut down then......
-
Should we turn the device off or just turn the tv off?
We just purchased our Apple TV tonight and was wondering if we should turn the box off when not watching.
It doesn't turn off (apart from unplugging), you can put it to sleep (or set the timer to do so). However, it uses very little power so it's not an issue to leave it running.
-
HT1807 My iPhone turns off when I turn the GSM radio on.
The iPhone 4 reboots when GSM radio is turned on. You can use it when it's on a charger, but turn off fast when you use the GSM radio.
Basic troubleshooting steps as outlined in the User Guide are restart, reset, restore from backup and finally restore as a new device. If you've tried ALL 4 of these steps and you're still having problems, by all means, bring your phone into an Apple sotre for evaluation.
-
Hello yal.
My ipod nano's music stops playing when i sleep the ipod... and sometimes the screen is unresponsive. It is a little bit smasshed so yeah... could that be a factor?Your nano is pausing playback when the screen goes dark (Either when it goes dark on its own or when you click the sleep/wake button). The reason for this is that it is not detecting your headset. You may be able to hear music, but the headset jack is not inserted enough for the nano to detect that it is there (or something is blocking the connection). Here are your three options:
Insert the headset jack harder. Most folks find that this solves their problem. If you can see ANY of the silver of the plug when it is inserted, it is NOT fully inserted. You should feel and hear a click" when it is fully inserted.
Clean out the crud in the headset port. If you have tried #1 and it just won't insert all the way, it is likely that you have crud in your headset jack. Shine a light in there. The entire inside of the jack is white, so if it looks dark down at the bottom, there is probably crud down there. You can try blowing it out or using canned air. Just understand that shoving anything else in there to clean it out will be taking your warranty into your own hands! However, I have cleaned mine out using whatever was handy and small enough to fit in there and so far so good. Your results may vary!
Take it to the Apple store. If you have really tried with 1 and 2 and it is still happening, then there might just be something up with your headset port or your headset jack. If it is the headset jack, you can look closely at that and be pretty sure if that is the problem. Try another headset to make sure. If you have worked all the way through to this point and it is still happening, it is time to take it to the Apple store.
i -
Does IMessage turn off when someone turns their phone off?
If you both have IMessage and they turn their phone off will it automatically revert them back to text message instead or should their Imesssage icon still be available?
Even if you select Shutdown and then close the lid before it is able to it will go into sleep mode. This is normal and has been consistent for quite a long time. Even though it is in the process of shutting down the system is still running while it happens so will respond to certian actions until it actually does… like asking it to sleep (by closing the lid). All you need to do is wait a few seconds for it to shutdown before closing the lid.
-
Basically yesterday my iphone started requiring me to go through the activation process (connecting to wifi, logging in to itunes,etc.) I have tried r
I have tried restarting it but each time it requires me to log in again.
-
my i phone wont connect to my cellular network but will connect to my wifi. it recently crashed so i restored it via itunes it restored fine and then wouldnt let me use my internet or send messages because i have no 3G how can i fix this?
No try this go to settings>general>reset>reset all settings "please note you will need to reput your wifi password in and nothing will be erased"
please let me know if this helps d:-)
jaydin curl "first level apple care rep" -
I have the dumbest question. Is there an off button just for the music? I can't get my music to stop playing. When I turn the sound off, the music goes on and on and the sound won't work on other apps. Am I doing something worng? Haven't had this thing very long.
You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download this guide to your iPad.
iPad User Guide for iOS 5
http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
Cheers, Tom -
I do not know what the problem is, but after the latest update it is really hard to send text messages. It is taking alot of time to send the messages, it is not the problem with the carrier because sending text messages with the same number in the same area is really easy on my normal nokia 1100. Please suggest me what I should check. Second problem I am facing is the carrier signal drops to nothing when I turn on the cellular data. It has to then search for the network and connect again the same happens when I turn the data off again. Please tell a solution. I do not think it is the problem with the hardware because the phone is hardly 2weeks old and everything was working properly with ios 6. It initaly had problem with the battery on updating to ios7 but that was rectified with the new update but again these are the new issues am facing.
This may sound stupid, but I'm gonna throw it out there anyway. Is it possible, that if I have enough junk on my desktop it might disrupt the signal? It seems odd, but it kind of looks like my signal is strong and relatively steady now that I've cleaned my desktop. I do tend to get very cluttered. I use a lot of reference images and save text clippings to use later... it just piles up very quickly.
So, I wonder if all that extra effort my system has to do keeping up with the junk might have something to do with the drop outs?
Maybe you are looking for
-
HP Deskjet F4440 not printing from cups, do I need ppd? Where can I find it?
Hello!, I am trying to get my HP Deskjet F4440 connected to my linux server through the use of "cups". I am using Tiny Core Linux. Linux box 3.16.6-tinycore #777 SMP i686 GNU/Linux I have installed and configured cups.tcz. When I visit the cups admin
-
Flex Builder debugger breakpoint folows wrong lines
this morning i start seing strange things happening with flexbuilder, first it seeme that it was entering code that was physically impossible; things like entering "if" clause and then immediately entering " else " clause, finally i realized debugger
-
Problem with "describe requirement"-function by creating SC
Hi all, I have a problem by creating a SC with the "describe requirement"-function. If I use this function a regular SC is created and a purchase order is also created with the stauts hold. I do not want to create a purchase order because if the shop
-
I can't install Photoshop on my Mac. The installation bails halfway through...
I get the error message: "The Installation Failed. The installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance." I have enough memory and all other software is up to date..
-
Any Explanations y this query is not ordering ?
SELECT dept_id, salary, job_id FROM employees ORDER BY ( SELECT dept_id FROM departments WHERE last_name='Abel'); Assumptions: 1. The inner subquery gives a value of 10 only. 2. There is no 10th column in the Table Employees. 3. There is only 1 emplo