Streaming Video through xbox 360 causing router to...

Can anyone help with this? I have recently got SKY player and my router just reboots randomly which is so annoying!! I have had a BT engineer come over a few weeks ago and he said my line was fine.

BT speedtester is now working:
FAQ
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
7892 Kbps
0 Kbps
21000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 7892 Kbps
For your connection, the acceptable range of speeds is 4000-21000 Kbps.
Additional Information:
Your DSL Connection Rate :10279 Kbps(DOWN-STREAM), 1016 Kbps(UP-STREAM)
IP Profile for your line is - 9069 Kbps
2. Upstream Test: -provides background information.
Upload Speed
816 Kbps
0 Kbps
1016 Kbps
Max Achievable Speed
>Upload speed achieved during the test was - 816 Kbps
Additional Information:
Upstream Rate IP profile on your line is - 1016 Kbps

Similar Messages

Stream iPod Touch Through Xbox 360

I want to stream my iPod Touch through my xbox 360. I heard that it doesn't work because the xbox sees it as a computer rather than an MP3 player. Is there any way around this?

yeah. that would be slightly difficult though since the creator would need to contact someone from Microsoft who deals with Xbox software, in order to get the codes (or whatever) needed to get the app to work. it still would be great though.

PS3 / Xbox 360 / PC Router Guide For GAMERS

Downloadable for Wordpad or Microsoft Word: http://www.filefactory.com/file/b1e67ga/n/Gaming_Router_Guide.rtf
Or just read below:
PS3, XBOX 360, PC GAMING
Router Guide and Modem Guide
Introduction:
Having issues trying to get your PS3, or XBOX 360 from Strict, or Moderate NAT? Want to get Type 2, "Open" status? Then follow this guide step for step.
(Please refer to your manual or other posts if you are unsure how to access a certain step, or post a quick reply on the forum. You can usually access your Linksys router via Internet Explorer by typing 192.168.1.1 - password is usually admin, username blank or admin as well.)
All of these steps were performed on the following test setup:
1 - Laptop PC (Windows XP)
1 - PS3 Console
1 - Motorola Cable Modem (SB6120)
1 - Linksys Router (WRT310N V1)
Firmware Update:
1)   Download the latest firmware for your router
2)   Install firmware onto router.
3)   Wait 1 minute after it has finished
4)   Unplug your Cable or DSL Modem's power, and ALL other devices that connect to the router. Leave them off.
5)   Click the "Reset to factory defaults" button in the router."
6)   Wait 1 minute after the lights stop flashing erratically.
7)   Physically go to the router, using a pointed object press the "Reset" button and HOLD for 30 seconds, then release.
8)   Access the router interface (example: 192.168.1.1)
Quick Tips and Information:
*The following settings are assuming you are now at "Default" settings. If you are not, than some settings may have been overlooked and you may have the wrong settings.
*You MUST use a WIRED connection for these steps. You can even use your PS3 or Xbox 360, and use the browser to access the router if your console is a wired connection. That is what I had to do, because my laptop is wireless only.
*The biggest mistake people make, is not clicking "Save Settings" at the bottom of each page, before moving to the next section. You MUST click "Save Settings" on each little page. Including the sub-pages. This is a huge deal. Even though the settings will "Stay" how you clicked them, they do not actually go into effect unless you hit "Save Settings" on every page.
*At this stage, any unnecessary devices must be turned off. Only the router and one device should be connected through wired Ethernet. Use that device to perform the following steps:
SETUP > Basic Setup
9)   Internet Connection Type: Automatic DHCP
10) MTU: Manual, 1500
11) DHCP Server: Enabled
12) Start IP Address: 192.168.1.2
13) Maximum Number of Users: 2 (set for how many devices you have. 1 laptop, 1 ps3 = 2)
14) Client Lease Time: 0
15) Time Zone: Set for your time, and "Check" automatically adjust for daylight savings.
*Click “Save Settings” before moving to another tab.
16) DDNS and Mac Address Cloning tabs should have "Disabled" option set.
*Click “Save Settings” before moving to another tab.
WIRELESS > Basic Wireless Settings
17) Change to "Manual"
18) Network Mode: Wireless-G Only (My laptop is wireless and has a G-card. Set accordingly)
19) SSID: set this to something you like: (example Pro Gamer)
20) Standard Channel: 11
21) SSID Broadcast: Disabled
22) Wireless Security and Mac Filter tabs should have "Disabled" option set.
      *Click “Save Settings” before moving to another tab.
WIRELESS > Advanced Wireless Settings
23) AP Isolation: Disabled
24) Frame Burst: Enabled
25) Basic Rate: All
26) Transmission Rate: 54 Mbps (I am using wireless G. Set accordingly, but do not use auto.)
27) CTS Protection Mode: Disabled
      *Click “Save Settings” before moving to another tab.
SECURITY > Firewall
28) SPI Firewall Protection: Disabled
29) "Uncheck" ALL options: Filter Anonymous Internet Requests, Filter Multicast, Filter Internet NAT Redirection, Filter          IDENT, Proxy, Java, Active X, Cookies.
      *Click “Save Settings” before moving to another tab.
30) VPN Pass-through tab: should have everything "Enabled"
      *Click “Save Settings” before moving to another tab.
APPLICATION AND GAMING > All Tabs
31) Skip this section for now, however if you did NOT reset your router to defaults before beginning. UNDO anything you         already have enabled on each of the five tabs.
ADMINISTRATION > Management
32) Router Password: change to something you use
33) Web Utility Access via Wireless: Disabled
34) Remote Management: Disabled
35) UPnP: Disabled. Including the 2 options below it.
      *Click “Save Settings” before moving to another tab
36) On the Diagnostics tab, click "Reboot" (may be located on very first page under “Setup”)
37) Restart whatever machine you are currently using to do this.
38) Turn on all devices that will be connecting to the router, except the cable/dsl modem.
39) Log into the router with your new password. On the first, page you should see "DHCP Reservation" click this. At the top, you should see one device named PS3-something probably numbers. If it is blank but there is an IP address, that is okay too. Click the box to the right side of it. Your other devices should be there too, such as laptops and consoles, etc. Click the box next to each of them. Then Click, "Add Clients" Now you have just assigned a Static IP Address without going through the hassle of doing it manually. Now you will always have the same IP Address for each device.
      *Click “Save Settings” before moving to another tab
40) Go to "Application and Gaming" click on the "DMZ" tab. Change DMZ to "Enabled."
Source IP Address: "ANY"
41) Now for the most important part. Most people use destination IP Address. However, if for some reason your IP address of your device changes, well then you are screwed. So instead, click MAC Address, then click "DHCP Client Table" and then "Select" the device that you GAME on, such as PS3 or Xbox360. Click "Close."
      *Click “Save Settings” before moving to another tab
***** IF you game on multiple devices, such as a desktop computer, and a ps3. You must DISABLE DMZ, and instead ENABLE UPnP. Please be sure to also enable the 2 options right Below UPnP. Many people do not enable the third, and sometimes even the second option. This causes hosting/joining issues, as the ports do not open/close properly. If you only have 1 gaming device, DMZ is the better choice. However, if you game on more than 1 device, use UPnP.
***** DO NOT ENABLE DMZ & UPnP TOGETHER.
42) Go to "Administration" > "Diagnostics" > "Reboot"
43) Restart ALL devices (Except cable/dsl modem) then connect them to the router.
44) I would connect my laptop now, by using the dell wireless manager I have, use the wizard to find "Non-Broadcasting"       devices. Then I manually type in my SSID: (Pro Gamer) it pops up. Click "Connect,” then "Lock" then "Apply"
45) For my PS3 I turn it on, go to Network Settings, then Connection Settings, "CUSTOM"
      Leave everything Automatic or "Default" except for these:
      MTU: 1500 / UPnP: Disabled (If DMZ is enabled on the router) / UPnP: Enabled (If UPnP is enabled on the router)
If your console (ps3/xbox360) was the wireless device, then simply select, "Wireless" and click manual SSID type "Pro Gamer" or whatever your SSID is, then continue with the rest of the settings. Security should be none/disabled.
ALMOST DONE!
This next tip is almost completely UNKNOWN by the gaming community. However, it is spectacular. Did you know the cable companies increase their speeds over time for FREE? Here is how to get your free upgrade. Even if your speed does not change, this will upgrade your Cable Modem's firmware! (DSL modems must be done manually, check online.)
Use a 7/16 wrench if connections are too tight.
While the Modem is OFF, unscrew the coax cable from the modem. PAY ATTENTION to this step. Now unscrew the other side from the wall or splitter. Then, REVERSE them. Reconnect the coax cable to your modem using the OTHER side (the one that was plugged into the wall), and vice versa. Make sure they are snug, but do not over tighten.
What does this do? Well I do not know the exact inner workings, but my friend who works for Comcast told me about this trick. It forces their system to re-register your Cable Modem. So now, you get a new IP Address, and it forces your modem to check for the latest firmware update. Along with that, come your increased speeds for FREE.
a)   Now, plug in the power to your modem. Wait until all lights are steady.
b)   Then go to your computer, (Do not use the PS3 or Xbox for this step)
c)   Type 192.168.100.1 (might be different for your modem, Google it)
d)   This is your MODEM's page.
e)   Look around for an option that says, "Reset to Defaults"
f)   Click "Reset to Defaults"
g)   Wait 30 seconds. It will not do anything.
h)   Now, you must click the other option, "Restart Cable Modem"
It will now clear out the memory, check for new firmware, get an updated IP address, and hopefully give you improved speeds!
That is all. Happy gaming! Visit www.speedtest.net and www.pingtest.net to test your connections.

Hey thanks for this, but one thing I have to ask is about the modem part. I unhook the cables and reversed them and then turned on the modem the lights are on and stable now. I have a sb6121 and when the modem is completely active it goes green, blue, blue, green, which is power, downstream, upstream and then online. But when I did what you said it is green, blue, "green"!, green. So since its different do I wait for the upstream to turn back to blue, or do I have to call comcast and give them the mac address again? I have been waiting for 5 mins so far and don't want to restore defaults and restart till I know I should for sure.

Streaming videos through apple tv

Since the upgrade to iOs8 I cannot stream videos to my tv through appletv. If they work, it crashes a few seconds into it.
Also, the little icon on the bottom right corner of the video where I would choose which device to play the video on (phone, and other apple tvs), is gone. Do we have to go to settings and enable air play every single time?
I want that icon back.

I am having the same problem. Since the IOS8 Upgrade,I have been unable to stream videos without it crashing every few minutes. Nothing else has changed. Same router, same devices all with the same wiFi connection. Most of the time when it crashes and I finally get it to start again, the video always starts from the beginning again, very annoying. Before the upgrade.... no problems at all. I also checked out the link to resolving issues with airplay etc. and nothing there has solved this problem. I hope Apple will address this problem and come up with a fix. I love my Apple products, but love them even more when everything works properly

Iphone 4 Video and Xbox 360 as my PC's Windows Media Center

I noticed that all video formats play perfectly over my Xbox 360 except for video shot with my iphone 4. It plays the video in slow motion while the audio is at regular speed. It's very annoying. Is their a fix for this or do I just need to convert the iphone 4 videos to h264 mp4, or regular mp4? Any quick fixes so I don't have to do the converting? When I play them on my HP they play just fine. I'm assuming it has something to do with the Xbox 360 not having an updated codec. Any ideas will be tried.
Thanks

I'm in the same Xbox 360 boat. I'm also amazed at the lack of information on this problem since the iPhone 4 has been out so long and the Xbox 360 received an update long after.
It has to be a codec issue since the Xbox 360 can play 1080p content. The iPhone 4 720p video can't be more intensive than 1080p.
While I'm at it why can't the Xbox 360 play iTunes Plus and iTunes Lossless audio, they're DRM free (I use Connect360 to get around the issue)? Seriously, Microsoft has to be doing it on purpose. Every attempt I've made to get this question answered has been met with a MS wall.

No Longer Able to stream content to Xbox 360

I have just installed Lion and can no longer stream media to my Xbox 360 using Rivet. I had no problems streaming them before, and am still able to stream the media on my 2TB NAS drive but it says the format is not supported on my Xbox when I try to play media on my MBP (with Lion). All of the files are regular .avi files, and play fine on my machine. Anybody else having issues streaming to xbox 360 since upgrading to Lion?
Thanks

It happened the same to me using Rivet and streaming (from my iMac) to my TV directly (has Wifi).
In Rivet webpage says that Rivet is no longer supported by them (so I supose that there is no update for Lion). Nevertheless, I have tried with other media servers (like Serviio or Majestic) and doesn't work either...
Anybody know if there is going to be a patch or a solution?
Thanks a lot, greeting from Spain :-)

ITunes 7.4 will not stream video through front row

I just updated both my macbook pro and my mac mini to iTunes 7.4.1(2). I also updated the firmware for my airport extreme base station. I can no longer stream video using front-row. This happened before when I updated to iTunes 7.2! I suspect, like before, apple will have to send out a patch. Anyone else expierenced this?

Try turning IPv6 ON in your network preferences - this is helping SOME people with this problem. It won't help you at all if your network router doesn't do IPv6.
To turn on: go to Network Preferences, select the interface you use, under teh TCP/IP tab click 'Configure IPv6', and choose 'Automatic'. Save changes.

Streaming Video through Web Content Overlay

Really would appreciate some help here. Whenever I link an HTML file containing a MP4 video through the Web Content Overlay, all the other body text in the pages no longer render as vectors (the text becomes pixelated). The video is in H.264. Any ideas?

Does the video streaming source link has the same page resolution as your folio is? Did you check the option "scale content to fit" is web content overlay?

Stream ipod to xbox 360?

my ipod doesnt work on any xbox 360s. i was wondering if there was a program that can share/stream my ipod music from itunes to my 360. i found a program called connect360 but it only browses my itunes library, not my ipod. all my music is on my ipod to save harddrive space. thanks

Hi viceng,
I've been using connect360 (paid the $20) and it's a fantastic program, it was designed to be a streaming plug-in to your media library. I've yet to find a similar program that allows you to access the mounted iPod and stream it out across the network.
With that being said, the iPod was not designed to be the only location for your music. My understanding is that Apple always envisioned the iPod to be a way to take the media on your computer with you, not have it as the primary storage location.

How to play iPod through Xbox 360?

If anyone knows how to play an iPod on the Xbox 360, then could you tell me how to please? I know that i have to configure the iPod to play through the USB port but i don't know how to do that so if someone could tell me how to do that too, that would be amazing. thanks

TRY THIS
http://www.xbox.com/en-US/support/systemuse/xbox360/digitalmedia/ipod.htm
and then try updating your xbox 360 console
http://www.xbox.com/en-US/support/systemuse/xbox360/console/systemupdates.htm
let me know what happens
i have the same ipod but not connected yet

Configuring xbox 360 w/ router

I am trying to configure my xbox 360 to my wireless router and am having a little trouble. Any advice will be appreciated.

Still Havin some problem try this ....
Connecting Xbox To The Wireless NEtwork / Wired Network
needed to Go to the System area of the Xbox Dashboard.
Select Network Settings.
Select Test Xbox Live Connection.
The system will perform a series of diagnostic tests, the results of which can help you configure your network to access Xbox Live.
In each case, the More Info section will offer tips for correcting the conditions preventing you from accessing Xbox Live.
any test failed is a point of concern.
In most of the cases i dealt, i provided the Static Ip address to XboX console as in
e:g 192.168.1.55/192.168.1.1 ....
and tested the Connection ....It worked for Me !
To Provide Static ip on Xbox , Tell user to access Edit Settings option !
In edit settings user will find Three or four options Which should be either automatic or manual
1. IP address - Automatic/manual - select manual and give static inf
2. DNS - Automatic/Manual - select manual and give static inf
3. MTU - Automatic (alwayz-important)
Test the xbox live connection , it Has to work after these settings.
This Article Is By me .
happy Gaming n hope it works for u.
~~~Nobudy's Perfect , i try To Be So ! Each n every moment of maH LYF , AND I THINK dat wats make Me "Different" From others....~~~

Streaming video through Windows Media Player using USRP

Is there any document / guide or any example explaining how to do streaming through Windows Media Player using USRP.
Thanks
JK

Joseph,
I have been looking a bit more and have found a few examples that seem similar to what you are looking to do. Here is an example of video streaming using USRP RIO or FlexRIO https://decibel.ni.com/content/docs/DOC-40747. I also found an example of doing wireless streaming of video https://decibel.ni.com/content/docs/DOC-22728. Sorry I was unable to find these in my first post; I hope they help!
Scott B.
AE NI

WRT160N V3 Xbox 360 trouble router randomly resetting PLEASE HELP

For Christmas 2009, I received the wrt160n v3 Linksys by Cisco router. This router worked fine until about early November of 2010, when I would turn on my xbox to play a multiplayer game, and the router would randomly reset and i would lose my connection, as well as all the computers connected to the router would lose their connection to the internet. I actually sent that one back to linksys through an rma and received a new one of the same model and version, and I am still having the same problem. The router even resets when I am not on my xbox, simply just on my laptop. It is incredibly frustrating and cannot seem to find any help on the internet. Does anyone else have this problem? Are there any solutions? Is it my router or could it be my xbox screwing everything up? Any help is welcome, thank you very much

nevermind my router just reset while playing xbox. mtu is 1365, i unchecked that box, and opened my nat type, and it still reset. im starting to get extremely dissatisfied with your products

Problem Streaming Videos Through iTunes U Private

We have recently received reports from students and faculty that they are unable to preview longer videos hosted in iTunes U Private. While this problem seems to affect longer videos with file sizes over 500 MB, there does not appear to be a specific file size or video length that causes the problem (e.g. Some files less than 400 MB do not play, and some files larger than 700 MB do play). This problem only affects people using iTunes client version 10. The same videos that cannot be previewed in iTunes 10 play fine in iTunes 9 without downloading. All files play in all versions of iTunes client after downloading locally.
We confirmed Virginia Tech is seeing the same issue. Can anyone else confirm they are seeing the same issue? If so, please let us know if you have any ideas about the cause, a good workaround or a permanent fix. We have a very angry department chair in Film, Theater and Television that we would like to make happy soon.
Please contact [email protected] if you would like to Discuss.
Thanks in advance,
Academic Technologies at Notre Dame
Message was edited by: atsnd

We are currently investigating this issue. We'll keep you posted on our findings.
iTunes U Team

Stream video through web page..

I am fresh in JMF programming, recently i'm learning video streaming over the Internet (on demand broadcast).
i need to be able to putting the video on my web pages, and JMF client as media player.
Can someone help me? is JMF has web browser plug in?
Thanks a lot

Hello
I'm interested in this subject... if someone can help us i give my email.
[email protected]
Thanks

Streaming Video through xbox 360 causing router to...

Similar Messages

Maybe you are looking for