Stuck at white screen with grey apple logo

When I turn on my MacBook Pro, it is stuck at the white screen with grey apple logo. What do I do?
Thank you!

I was looking at this and it helped! http://support.apple.com/kb/TS2570
1) Disconnect, test peripheral devices and network cables - didn't work
2) Perform a Safe Boot - didn't work
3) Reset the NVRAM / PRAM - worked, yay!

Similar Messages

Macbook starts up with chime then white screen with grey apple logo and spinning gear appears and continues to spin

Help, Turned on MacBook Pro this morning and just get a white screen with grey apple logo and spinning gear. Cannot access desktop.

Computer starts up in Safe boot by holding down the shift button. But when I go to restart the same thing happens. What should I do?

Mac Stuck at Startup Screen with Grey Apple Logo,Empty Progress Bar and a Spinning wheel

Last night the electricity went out and my power surge protector was not working so my iMac just force shut downed.
So, when the electricity came back i turned on my Mac but it is *Stuck in the Startup/Boot Screen with a Grey Apple Logo,a Empty Progress Bar with stays for 1 or 2 minutes and a small Spinning Wheel which would Spin Forver! I Have tried the SMC and Pram reset but no use, i have also tried to insert my OS X Lion 10.7 Installation disk and it would not load if i hold the C Key in the Startup, I Have Managed to go to Disk Utility Through "Recovery HD" but the Volume "Macintosh HD" is Greyed out and Unmounted and i cannot repair it. There are some files that i'd like to Recover if there is a way to fix it without deleting files.
**PLEASE HELP ME FIX THIS!**
Details about the iMac:
iMac 21.5 Inch i think from Mid 2010,
OS X Lion installed maybe 10.7.2 or 10.7.3 (im not sure)

kernel
Grey screen with Metallic Apple and spinning gear
Sounds to me like your hard drive failed on you as a result of the power going out.
http://www.apple.com/support/imac-harddrive/
If your iMac is a Mid 2010 you qualify for the hard drive replacement program from Apple.
Apple has determined that certain Seagate 1TB hard drives used in 21.5-inch and 27-inch iMac systems may fail. These systems were sold between October 2009 and July 2011.
I hope I helped you with your problem.
- Brandon

TS2570 tried restart and hold c key, but still only getting white screen with grey apple logo and spinning loading icon, what do I do next?

nephew had mutliple tabs open and shut down the iMac by hitting the button on the back instead of closing everything corectly. Now the only screen i get is the white with apple logo and the loading circle icon. i have attempted restart and c key with disk in but cant even get a menu to come up. What can I attempt from home before having to haul this into the store?

wireless keyboard and mouse were working prior to safe mode attempt, i was able to eject disk. still waiting on the safe mode restart. I'm not sure what I should be looking for to confirm safe mode and what the screen should look like if successfully processing. it seems to be putting off a lot of heat. BRB
Message was edited by: FeydakeeeeenHelpMePlease

Iphone stuck on white screen with black apple logo

I was updating my Iphone 5 to the new update and left it plugged in to finish the update. When I came back it was stuck on the white loading screen and a message on the computer said iTunes could not connect to the Iphone because it was locked with a passcode and wants me to enter the passcode. However I cannot enter the passcode because the phone won't let me. I cannot get the iphone to shut off or restart as my top button hasn't been very responsive lately. Any suggestions I leave the country for a month on the fourth and need a working phone asap.

You should contact Apple. There is a replacement program for defective power buttons.https://ssl.apple.com/support/iphone5-sleepwakebutton/

My iPad wont turn on, its black screen then i press home power buttons together and white screen with black apple logo come out after 5 seconds black "lighten" screen comes out and its stuck just like that! Whats the problem?

HI
this happened today suddenly while i was working on my iPad it kicked my out of the app that i was using then white screen with black apple logo came out, i thought it was an ordinary thing cause this happens all the time with me, but this time it refused to turn on! After the white screen with the black logo vanished i wad waiting for my lock screen but no, a black screen showed up just like that! And could tell it was black "lighten" screen i tried more than 10 times to do the home+power thing but it wont work, whats wrong with my ipad!

If the battery is completely drained it may take some time while on the charger before the iPad responds. Plug the iPad into the charger that came with it and plug that into a good wall outlet. Wait one hour. Then reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is 100%. If it doesn't start up make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support. They will examine your iPad and explain your options.

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star that just does that for hours

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I Mac freeze: When powered on all I get is a blank white screen with the apple logo. No "beach ball" nothing more. Tried all the usual restarts. Help?

I Mac freeze: When powered on all I get is a blank white screen with the apple logo. No "beach ball" nothing more. Tried all the usual restarts. Help?

Tried all the usual restarts. Help?
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.
===========
Your profile is a complete blank!!!!
When posting in Apple Communties/Forums/Message Boards.......It would help us to know which Mac model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
CLICKY CLICK-----> Help us to help you on these forums
***This will help in providing you with the proper and/or correct solutions.***

My iphone wont open, i even recovered it but to no avail, all it does is go to the white screen with the apple logo then turn off again

Hey everyone,
This morning i took my phone out of the charger and everything was normal however, once i got in the car i looked at my phone and realized it was turned off. I tried turning it on again as well but all it does is going to the start up screen (The white screen with the apple logo) and then it turns off again as well. I also put it on the charger but it does the same thing but repeatedly. So it just goes to the white screen and off again. At last i resorted to recovering my phone even if it meant losing all my data. Slow internet connection meant it took all night but in the morning i recovered and everything and got to the last step ( It told me its finished but i should leave my phone connected to itunes and it will pop up there) but all that popped up was an error screen. It still broken but now sometimes when i try to turn it on the same white screen with the logo comes on with a bar under it. this bar fills up a little then the screen goes black again. Is there any other way i can try to fix this?
P.S. There are no apple stores in my area so i took it to one of the phone stores here and even they said they couldnt do anything about it

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

I've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?

i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?

Look at this support article:
http://support.apple.com/kb/ts2570
Ciao.

I have a macbook and when I power it on and then select myself as a user...It won't power up. It stays in the white screen with the apple logo. I am online currently under 'guest user'. Is there anything I can do from the keyboard to fix this??? Help!!!

I have a macbook and when I power it on and then select myself as a user...It won't power up. It stays in the white screen with the apple logo. I am online currently under 'guest user'. Is there anything I can do from the keyboard to fix this??? Help!!!

Could you specify the model of MacBook and the OS X it's running, please? Some of the advice or references vary along with the system, so this could be helpful to formulate a reply. I've never used a Guest User selection, but do have more than one User.
If the computer does not have an optical drive, you may be able to boot it into a recovery disk mode or something; in an attempt to see what is wrong and maybe fix it.
Good luck & happy computing!

Plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat.... i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead..... pl

i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s...
plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat....
i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead.....
plugging the phone into the laptop NOTHING!!!!!!!!!!!!!!!!!!!!!
the laptop doe read my phone.....
no ding.....
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on

mariidb wrote:
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s... {snip}
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on
That's the problem. That's what the **** is going on.

HT3964 I am not able to reboot my Mac desktop. When I switch on the Mac, I get a white screen with the Apple logo and the little wheel below that goes round and round but the computer refuses to boot.

Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
Marcus

We need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post.

My iPhone 3gs is stuck on black screen with the apple logo, help

my iPhone 3gs is stuck on black screen with the apple logo, help

then get it replaced if that doesnt work or try to le tthe battery die and recharge

My imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?

my imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
I have started having trouble since i had to upgrade OS the latest in July 12.

http://support.apple.com/kb/TS2570 Follow this article and when it gets to the part where you go into disk utility using your install disc, you'll actually boot up holding down Command and R

Stuck at white screen with grey apple logo

Similar Messages

Maybe you are looking for