Stuck in an update loop, 3 of 3, do not turn off your computer

Hello,
We have all the updates ,update automatically.  During this last one, today, our server has shut down and is in a constant loop.  We are getting that the drives are both fine, but there is one error on the start up that has me concerned:
BMC System Error {SEL} Full
The system goes through "Configuring updates" Stage 3 0f 3, do not shut down, then on to a blank screen, then restarts on its own, goes through the whole start up, everything looks good except for that BMC error, than the microsoft is loading...and
right back into "Configuring updates", blank screen - its been on a continuous loop for about a half hour now.
Suggestions?  The computer does not stay on long enough to do anything, and it never actually gets to a start menu..
Thanks,
Kelly Campbell

Hi,
Before going further, would you please let me know the version of operation system that you use?
Meanwhile, please refer to resolution steps in the following KB. Then check if can troubleshoot and solve your issue.
"Failure configuring Windows updates. Reverting changes. Do not turn off your computer" error when you try to install Windows updates
http://support.microsoft.com/kb/949358/en-us
Regarding to the error message, should the complete information of this error be “02A2: BMC System Error Log (SEL) Full.”? If so, please refer to the following article
and check if can solve this error.
02A2: BMC System Error Log (SEL) Full.
http://clintboessen.blogspot.in/2013/05/02a2-bmc-system-error-log-sel-full.html
If I misunderstand, please don’t hesitate to let me know.
Hope this helps.
Best regards,
Justin Gu

Similar Messages

  • Help! My s3 is stuck on a "DOWNLOADING... Do Not Turn Off Target!!" page!

    I've had the worst time charging my phone since the new kitkat update. Today while my phone was plugged in to "charge" instead of the battery level increasing...it went down!
    I switched chargers and that didn't help, so I pulled the battery. Ten or fifteen minutes after putting the battery back in and turning on my phone, it acted like it was rebooting and then suddenly a green android guy popped up on my screen with the words: "DOWNLOADING... Do Not Turn Off Target!!" under it. In the upper left hand corner it says "factory mode". I didn't push any random combination of buttons...just the power button. I don't know what to do! Someone please help, I can't not have my phone.

    *update*
    My phone got past the android guy...but it won't charge still. It's stuck on the "charging" screen that shows up when the phone is off... but it won't boot up completely. It'll through the boot up process but once it gets to my main phone screen (where I can see my background and apps) it turns itself off again.

  • HT4623 How do I turn off aps with my new updated software?  They are not turning off like they used to.

    I just updated my software, now I don't know how to turn off aps.  I used to double tap the home button then hold down the ap until it shakes and the minus signs appear.  Now, I get no shaking and no minus sign.  What do I do?

    This short video show you how to do it:
    http://youtu.be/4cQNjSsd1xg
    It's a youtube video showing how to close apps in ios7 for iphone or ipad and save battery life.
    For those who like visual demonstration, hope this helps.

  • HT4061 My iphone 4 froze up. It is stuck on one of my contacts and will not turn off, let me answer the phone, or do anything else. Any suggestions?

    My iphone 4 is stuck on a contact and will not do anything. I can't even turn it off. Help me please!!

    See Here for  >  Frozen or unresponsive iPhone
    Try this First...
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...

  • IPhone 4s hang up after updating to ios 6.does not turn off screen goes to zoom.revert to normal after reset.occuring everyday when in locked mode.

    hi kindly help out what can be problem. mostly at same time in evening it happens

    To disable Zoom double-tap the screen with three fingers.
    Go to Settings > General > Accessibility > Zoom and turn this OFF.

  • My LG G3 gets stuck in an "updating" loop and not load new emails. How do I fix this?

    My LG G3 gets stuck in an "updating" loop and not load new emails. How do I fix this?

    If you toggle Airplane mode On/Off, does it resolve?

  • Hello i have an iphone 4 its stuck in the apple loop. when ever i unplug it from the computer it shuts down and when i plug it in it shows me on itunes its in recovery mood and every time i click restore i get this error the iPhone could not be restored.

    hello i have an iphone 4 its stuck in the apple loop. when ever i unplug it from the computer it shuts down and when i plug it in it shows me on itunes its in recovery mood and every time i click restore i get this error the iPhone could not be restored.an unknown error accurred (2001)

    Error 1 or -1
    This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
    http://support.apple.com/kb/TS3694#error1

  • My itouch will not turn off and is stuck with the apple symbol as if it is downloading an update.

    My itouch is stuck with the apple symbol as if it was downloading something.  I have tried to reset it by turning it off but it will not turn off.  Any suggestions?

    Hi,
    Try placing your iPod in Recovery Mode and restoring it via iTunes:  http://support.apple.com/kb/HT1808. 
    Hope this helps! 
    ---likeabird---

  • I tried updating my ipod, and then it turned off, and then just said connect to itunes, and when i did, it said i had to restore it. so, i restored it, and it did nothing and still said connect to itunes. help?

    i tried updating my ipod, and then it turned off, and then just said connect to itunes, and when i did, it said i had to restore it. so, i restored it, and it did nothing and still said connect to itunes. help?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     
    or
    Maybe:
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
    Next try placing in DFU mode and then restoring.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    Then try restoring on another computer.
    Last, make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • HT201210 i updated my 4s yesterday, but my phone will not work at all now, and will not turn off. It has a itunes image on the screen with an arrow undernieth and what looks like the charger lead. i've had it on charge! is there anything else i can do?

    i updated my 4s yesterday, but my phone will not work at all now, and will not turn off. It has a itunes image on the screen with an arrow underneath and what looks like the charger lead. i've had it on charge! is there anything else i can do?

    Cconnect it to your computer with the latest version of iTunes installed.

  • I tried to eject a cd, didn't work so I turned off the computer and now it keeps getting stuck at the gray screen. How do I fix it?

    Here are a few more details. I put in a game cd for a windows computer, once I opened the folder on the desktop I noticed the install application was .exe so I tried to eject the cd but no matter what I tried on the computer it wouldn't come out. I will say though that I didn't try the manual cd eject cause I didn't have anything small to hit the button in the cd drive with. It was getting late so we decided to just turn off the computer and leave it for the next day. I can't remember if we turned the computer off with apple shut down or by holding down the power button but we walked away pretty quickly before it was fully shut down. The next day the computer won't turn on. When I walked into the room I was the computer stuck with a grey background with the apple logo showing and the circular thing under it frozen. Since no one was in the room I held down the power button and turned the computer off. We tried to start the computer again later but again it keeps getting stuck at the same spot. Now when we hold the power button down to turn it off I'm not sure if it's really turning off all the way. The screen goes dark but it sounds like the fan is still going. I tried disconnecting everything but the keyboard and mouse but when I started it up again it got stuck on the grey screen with just the apple logo. I'd really apprechiate help on this cause I live in Germany right now and support call centers work so much worse when you don't speak the language well... Thanks for any help you can give!

    Restart your computer while holding down left mouse key. That will eject the CD and your Mac will start as normal.
    Lupunus

  • Hot Fix error message for KB979344 "this update is not applicable to your computer", on Windows 7 64 bit with SP1

    I've been having issues with an external Esata drive.  Instead of being seen as a removeable drive, it is seen as a hard drive.  This has caused us nothing but problems since our full disk encryption software automatically starts to encrypt
    the drive rendering it useless.
    The real problem I'm having is installing the Hot Fix, KB979344, for this issue.  when tring to install, I get the message, "this update is not applicable to your computer"  I've looked and this hot fix doesn't seem to be part of SP1, but
    I could be missing it.  Any thoughts? 
    Thanks,
    Keith

    Hi Keithk,
    This hotfix is already contained in Windows 7 Service Pack 1.
    Please add the registry key to check if the issue persists. (For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs.  )
    Navigate to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Storage  
    Create a DWORD Value, name SATAHotplugPolicyOverride,
    set 1 in Value Data.   
    Restart the computer to check if it works.
    Regards,
    Miya  
    TechNet Subscriber Support in forum. If you have any feedback on our support, please contact
    [email protected]
    This posting is provided "AS IS" with no warranties, and confers no rights. | Please remember to click "Mark as Answer" on the post that helps you, and to click "Unmark as Answer" if a marked post does not actually answer
    your question. This can be beneficial to other community members reading the thread.

  • Windows Server 2008 R2: "The update is not applicable to your computer"

    ALCON,
    I'm trying to install a "Windows Update Standalone Installer" file (Windows6.1-KB3032323-x64.msu) along with other .msu files and I keep getting the same message: "The update is not applicable to your computer".  The server is a
    virtual machine and is also the vCenter server for the system, so I REALLY don't want to mess this installation up and break the system but the installation is needed and mandatory.  How can I go about installing these .msu files. 
    *Note*  The system is located in a classified environment so it doesn't have a connection to the outside (unclassified) world.  But I'm able to have the .msu files placed on the system at any time. 
    Thanks!
    V/r,
    Stanley L. Johnson Jr.

    Hello,
    do you use SP1 for Windows Server 2008 R2?
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://blogs.msmvps.com/MWeber
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
    Twitter:  

  • The Update is Not Applicable To Your Computer when installing patch on Windows Server 2008 R2 machine

    When I try to install security patch KB2525694 and KB978542 on my Windows Server 2008 R2 machine, I get the message "The Update is Not Applicable To Your Computer".  I am using the following files:
    Windows6.1-KB978542-x64 (KB978542)
    Windows6.1-KB2525694-x64 (KB2525694)
    I believe these are the correct files but no luck installing it.  Any help would be greatly appreciated!

    When I try to install security patch KB2525694 on my Windows Server 2008 R2 machine, I get the message "The Update is Not Applicable To Your Computer".  I am using the following files:
    Windows6.1-KB2525694-x64 (KB2525694)
    This update has been superseded many times.
    If you already have installed one of the superseding updates below, KB2525694 will not be applicable.
    For the list of superseding updates, check this list:
    http://catalog.update.microsoft.com/v7/site/Search.aspx?q=2525694%20r2%20x64
    (click on the result, then click on the "Package Details" tab to get the list below..
    This update has been replaced by the following updates:
    Security Update for Windows Server 2008 R2 x64 Edition (KB2555917)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2567053)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2639417)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2641653)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2660465)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2676562)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2709162)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2718523)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2731847)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2761226)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2778344)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2778930)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2779030)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2808735)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2829361)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2850851)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2876315)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2883150)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2893984)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2913602)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2930275)
    Security Update for Windows Server 2008 R2 x64 Edition (KB2973201)
    Don
    (Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
    This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

  • Did the most recent update and now my TB Display turns off randomly on both my air and mini. I running  TB Firmware Version:     23.6

    did the most recent update and now my TB Display turns off randomly on both my air and mini. I running  TB Firmware Version:
    23.6

    When did you get this firmware version?  My TBD is at 22.2 and the TBD bus is at 23.4.  I thought I had the latest firmware.

Maybe you are looking for

  • Why am I not able to use iCloud Drive with the Mail app?

    I have an iPad Air and recently updated to the latest iOS currently version 8.0.2.  I understand that Apple just opened up iCloud Drive to be able to access your documents or anything within your iCloud account.  I like the feature of being able to a

  • Files moved from VirtualPC for Mac show up as being "written" in the future

    hi kids i have a windows app i use in VPC 7.0 on my ibook with OSX 10.5. i plug in my 1GB usb drive, unmount it from the Mac and mount it in VPC. i backup some .mdb (microsoft database) files from the Windows app to the usb drive, and when i mouse ov

  • XMLQuery fails when executed as a job

    Hi all, I build a query that checks the data server connections, using the string server://XMII/Illuminator?Service=SystemInfo&Mode=Status&Content-Type=text/xml The query works fine by itself and executed in a BLS. However, when I schedule the BLS, N

  • Smart switch app problem

    I have been trying to use the Samsung app, Smart Switch Mobil to transfer a lot of contacts, photos etc from my Galaxy S3 to my new Galaxy S5.  I have the app on both phones and have followed the directions exactly.  The files begin to transfer, but

  • Reading pdf files on N73 problem

    Hello, When I open pdf files on my N73 mobile, I get the error message Not enough memory. Although I have got memory space is available. Thanks [signature delted by host]