Stuck On Apple Logo (boot menu) HELP!!!!!

Hello, I recently jailbreaked my ipod touch 4g and all i wanted to do was to instal siri. I followed the instructions as they were given but after my device rebooted its stuck on the white apple logo now what can i do? Also I tried to restore it using itunes and i get error "3194" and after getting help from the internet it told me to downoad TINYUMBRELLA somehow, the error 3194 is removed but instead of that another error shows up when it says "veryfying the restore with apple" and that is error "11" please I need help can someone tell me what to do????

Check for hardware issues
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the alert when you update or restore, contact Apple support.
Common errors: 1, 10-47, 1002, 1011, 1012, 1014, 1000-1020.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar                                      

Similar Messages

  • My iphone 4 regularly gets stuck on the apple logo screen and stays there until it runs out of battery, and even during charging. what can i do? I have restored it, still it gets stuck on apple logo, anyone pls help.

    my iphone 4 regularly gets stuck on the apple logo screen and stays there until it runs out of battery, and even during charging. what can i do? I have restored it, still it gets stuck on apple logo, anyone pls help.

    Jai141 wrote:
    ... and im not sure as i brought the phone of someone else..  i will have to ask them
    Good Luck.
    Jai141 wrote:
    Thanks
    You're Welcome.

  • MacBook stuck on apple logo. Repaired disk using disk utility, but when I restart, I'm still stuck on apple logo. Please help!

    My MacBook is stuck on apple logo and heats up. I tried restarting in safe mode but it's still stuck. I also tried to repair the disk using disk utility. It says that HD is ok, so when I restart, I'm still stuck on the logo. Is there a way I could fix this without loosing my files?

    Restart your Mac while holding down the Command + R keys so you can access OS X: About OS X Recovery
    From there you can reinstall OS X, repair the startup disk, and restore from a Time Machine backup.
    FYI ... wiht ML installed, the only way to repair the startup disk is OS X Recovery, not the Disk Utility app installed on your Mac. You can verify but not repair.

  • My Mac g5 is stuck on apple logo screen, please help!

    I have a Mac g5 before they had intel (so its pretty old) and today it was stuck on the apple logo screen and the fans become really loud. I don't know what's wrong with it, I'm scared to do anything as I don't wanna lose all my files. I was going to take it to the apple store to get it fixed but if there is nothing they can do I don't wanna take a 45 min drive to get there. Any info will help! Thanks!
    Megan

    Hi Megan,
    Most Apple stote don't know what a G5 is, nor will most even look at them or work on them, so call 1st if deciding to try that.
    If worse comes to worse we can easily pull the drive(s) & get the info back most likely.
    You'll have to power off, then hold alt key at bootup to see if any boot disks show up.
    If not...
    Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
    /sbin/fsck -fy
    Repeat until it shows no errors fixed.
    (Space between fsck AND -fy important).
    Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
    http://docs.info.apple.com/article.html?artnum=106214
    Do you have the G5's Install Disc?

  • Ipod touch stuck on apple logo. Please Help!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    Ok, So Heres the whole story. I was trying to download the app "shozu" on my ipod from the wifi app store. a pop up came on my ipod and said that it was unable to download and it will be a available next time i sync my ipod with itunes. So i pluged in my ipod to my copmputer and itunes opened, it started to sync my ipod, it went through the long back up and then said syncing shozu to ipod. so i was waiting and noticed it said ipod sync complete, but i looked at my ipod and saw it was stuck on the sync in progress screen with the slide bar saying slide to cancel sync, but my ipod was froze. i waited awhile and it still was stuck on that screen so i disconected my ipod and held the sleep button and home screen button till my ipod shut off and the apple logo appeared. Its now been stuck on the apple logo for about 5 houre now. When i connect it to my computer, it takes about 10 minutes for itunes to reconize my ipod then it says syncing ipod in the itunes screen but my ipod is still stuck on the apple logo. pleaase help me fix my ipod. i desperatly need my ipod. i apreaciate any help at all. thank so much.

    hi i have recently had the same problem but had to restore my ipod touch more than a dozen times since march of this year. i sent an email to apple and within 3 working days they had collected my ipod by ups and delivered me a new one. i can only say what a fantastic service and whats even better i didnt have to download my music again its like it picked up from where it had left. fantastic service second to none, i suggest you try it apple have provided an excellent service. let me know how you get on. also there is a ver helpful book that i purchased from wh smith the rough guide to ipods isbn number is 978-1-85828-060-8 this is very informative and gives you a whole host of info that otherwise you would need a forest to print on line. donny

  • IPod Nano (4th generation) stuck on Apple logo! URGENT HELP!

    So it all started out when i had to reset it (which is menu + middle button).
    and it never came back from the Apple logo
    I have tried every thing! the five steps from Apple (reset, restart, restore, etc.), disk mode, restore..
    **BUT I GET NOTHING DIFFERENT FROM THE APPLE LOGO SCREEN!!**
    i have tried the tutorial on this page.. http://www.sharp-tools.net/archives/000240.html .. because the guy had my same problem but he resolved it with those steps...
    But in the diagnostics mode, he says to test ram & then hit play and blah blah... and then press +fast forward+ to go to DISKMODE entre... in the diagnostics mode i cannot find anything labeled with RAM or DISKMODE.
    i already know how to go to the diskmode MANUALLY (reset ipod > center button+play button) and it didnt help either.
    some one pls pls pls PLS PLS help!!

    Have you done a Reset (restarts iPod)?
    http://support.apple.com/kb/ht1320

  • HT201210 After i installed somethin on cydia (ACiD Siri iOS 6) It says Error then shut down then it is Stucked on Apple Logo! PLEASE HELP! whn im doing an Restore it says '3194' A little help?

    Sorry for my English please Understand =))

    This is user to user support site hosted by Apple, who don't want you to jailbreak your device, and don't like jailbreaking to be discussed here. You may get more help on sites that discuss Cydia, or you could try unjailbreaking the device.
    tt2

  • Iphone stucking at apple logo

    hey i changed my iphone touch screen and my iphone doesnt come up anymor it stuck on apple logo please someone help me !!!!

    Nothing that we can help you with.  You screwed up your phone trying to fix it yourself.  What would you like us to do?
    Apple won't even touch your phone now.  Either buy a new phone or bring it in to a 3rd party repair shop and see if it can be salvaged.

  • HT1267 stucked in apple logo

    My iphone 4 stucked in apple logo. Please help me!

    Firstly, have you changed any setting prior to getting this? Try restoring from itunes.

  • IPod Touch stuck on Apple Logo HELP!!!

    My iPod Touch 4g is stuck on the Apple logo. I have tried the home button and power button together and it keeps going back to the Apple Logo. And then it is stuck there. Please help!!!

    http://ipod.about.com/od/iphonetroubleshooting/f/Iphone-Stuck-At-Apple-Logo.htm
    Basic troubleshooting steps  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
     In Memory of Steve Jobs 

  • Mac stuck on apple logo, can't boot to disk utility...

    iMac 2010 running Yosemite.
    Stuck on apple logo with loading wheel but does not progress from here. Have booted in single user mode and proceeded to do the /sbin/fsck -fy steps until the volume was reported as okay, this did little to help. I can boot using the option key and can see the hard-drive and recovery partition are there however cannot boot using command+R to access the disk utility as it simply stays on the apple logo.
    Was wondering if anyone could advise what to do from here.
    Thanks in advance.

    Have you tried safe mode?

  • HT1414 After factory restore iPhone 3G is stuck on apple logo anyone help me ???

    Just wondering can anyone help me iPhone 3G 4.2.1 factory restore stuck on apple logo after restore its been 5 days now tried everything I could think of no luck was in recovery loop with connect to iTunes thingy but got it out of that seems like it finished restore then when it's suppose to sync with iTunes just stays on apple logo every once in a while it will act like its booting but goes right back to apple logo

    Try forcing it into recovery mode and restore it (seehttp://support.apple.com/kb/ht1808).  It you pc still won't recognize it follow the troubleshooting steps in #5 at the bottom of this article:http://support.apple.com/kb/TS1538 under "If device not recognized in Recovery Mode".

  • My Macbook is stuck on Apple logo when booting up!

    Hello,
        I have a Macbook Core 2 Duo that is stuck on apple logo, And I already tried inserting the mac OS x leopard disc but when I insert the disc and power up the Macbook it shows this picture down below. So if you have any answers that could solve my problem please comment down below Thanks!!!!

    OS X- About kernel panics
    OS X- How to log a kernel panic
    Visit The XLab FAQs and read the FAQ on diagnosing kernel panics.
    Note that panics at startup usually signal a hardware failure.
    Question (?) Mark, Blinking Folder, or Gray Screen at Startup
    These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
    A flashing question mark appears when you start your Mac
    Mac OS X- Gray screen appears during startup
    In most cases the problems may be caused by:
    Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
    Boot drive's directory has been corrupted - Repair with Disk Utility.
    Critical system files are damaged or deleted - Reinstall OS X.
    The disk drive is physically non-functional - Replace the hard drive.
    Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
    Boot From The Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Reinstall Snow Leopard Without Erasing The drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.
    Reinstalling Lion/Mountain Lion Without Erasing The Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • My iphone 3g is stuck on apple logo please help

    Hi my 3g is stuck on apple logo after a reset, I bought it second hand and was just removing the other persons settings, it now wont do anything, wont even recognise in itunes to restore, please help,

    Try forcing it into recovery mode and restore it (seehttp://support.apple.com/kb/ht1808).  It you pc still won't recognize it follow the troubleshooting steps in #5 at the bottom of this article:http://support.apple.com/kb/TS1538 under "If device not recognized in Recovery Mode".

  • I am trying to recover or restore my phone but it either says, error has occurred or it says they cannot find my iphone. It is stuck on the loading apple logo. Please help!

    I am trying to recover or restore my phone but it either says, error has occurred or it says they cannot find my iphone. It is stuck on the loading apple logo. Please help! I dropped it hard, maybe thats why it is not working.. and i put a new screen on it.

    to doublecheck you tried everything error 3194 http://support.apple.com/kb/TS3694#error3194

Maybe you are looking for

  • External HD Crashed

    Because my laptop has a small internal HD, I purchased a 500Gb external HD on which to store all of my iTunes songs. The iTunes app is on my C: drive, but the songs themselves were on an external E: drive. The external HD recently crashed, and needed

  • Does the symbol server work for current version?

    I followed the "Using the Mozilla symbol server" article in order to see symbols for Firefox in a debugger. But i still only get those "firefox.exe+1a05" entries, instead of "firefox.exe+Sleep" for example. All windows symbols work, but I never got a

  • Installing Sap Netweaver Trial Version

    Hi guys! I have installed in my notebook a sap netweaver trial version, but I have another PC with less resources than my computer. I would like to know if there is a posibility to have the sap gui in the second PC and use some like a Sap Route in or

  • FRM-92052 error... unable to connect to server URL /forms/servlet;

    Hi all. I'm on forms 11g 11.1.2.1.0 I'm configuring my form and when I try to run it I have this error: FRM-92052: unable to connect to server at URL /forms/servlet; I have start up weblogic server and everything is ok. When I try to run my form I ha

  • Avoid duplicate manuval document numbering for users screen

    Hai to All.                  Here we give manual docment numbering (user can enter any number that store in docnum) for our screen.It allow duplicate docnum to save.It gave an error as stoped by ui dpi.But it save the record.How can i avoid other tha