Stuck on start up screen, little wheel turning and progress bar hasnt moved. What can i do?

Stuck on start up screen, little wheel turning and progress bar hasn't move
Help
Thank you!

Useful article here on the causes of the Spinning Beach Ball and how to troubleshoot it:
http://www.computerworld.com/s/article/9177479/Troubleshoot_the_spinning_beach_b all?taxonomyId=89&pageNumber=1
and also this:
http://www.thexlab.com/faqs/sbbod.html

Similar Messages

  • I get a white screen with apple logo and progress bar on my imac mavericks

    I get a white screen with apple logo and progress bar ,then computer shuts down
    when I turn my imac back on same thing happens,every time same thing
    pprogress bar only goes half way then computer shut down
    is there a solution ?
    if not is there a way to at least salvage some files and docs?
    i Have the latest imac 27

    Thanks I tried it but after I repaired my disk via disk utility at start up, it told me that
    my disk can't be repaired and to try to back up my files so I can format it
    but is there to back up my files?
    also what I get is white screen with the progress bar not grey

  • My iphone 4s is frozen on the screen, of a plug and a itunes logo. What can i do to reboot it?

    My iphone 4s is frozen on the screen, of a plug and an itunes logo. What do i do to reboot or reset it?

    Your phone is in Recovery Mode. You need to connect it to the computer and iTunes and restore the device. Try this support document. http://support.apple.com/kb/HT1808

  • Updated iPhone 4s to ios8 but screen is stuck on white screen with apple logo and progress bar

    I updated my phone last night and my iPhone screen is white and has a gray apple logo and a progress bar which has been the same for 12 hours. The bar looks almost completel but it hasn't moved at all. my phone was also unplugged accidentally during the night while it was on this screen. would that have any effect?

    Turn it off, go into recovery mode (command R at boot), wipe everything, go back and install Yosemite. Its suggested that you are using ethernet as it goes a lot faster that Wifi and more reliable. If you do not have a ethernet cable, you can still use Wifi. Hope this fixes your problem.

  • Getting Grey Screen with Apple..and progress bar..  This is what I get

    Greetings all,
    I desperately need help..My macbook pro was running slow, and so looking online I found something about resetting smc and pram. Well I did both and the computer booted up fine. Then on my next reboot the machine wouldn't start. I'm getting the grey screen with the apple. A progress bar shows for a second but then goes away. I'm not able to get into safemode. But I was able to run the disk utility program from the snow leopard cd. Basically tellls me that the keys are out of order and then says "Error: Disk Utility can`t repair this disk...disk, and restore your backed-up files." This has to be bad.. I don't have a backup.. but luckily most of my stuff was on my macmini (I just had a baby so I had alot of pictures)
    Is my only option to erase? Right now the hard drive won't mount (atleast through the disk utility, since it can't repair it)
    Please tell me I have other choices.

    So you also have a Mac Mini? Then you might be able to retrieve files from the bad hard drive using FireWire Target Disk Mode:
    http://support.apple.com/kb/HT1661
    FWTDM will allow you to mount your Mac's hard drive on the Mini's desktop and it will be just like any external hard drive. You will be able to copy files from it.
    Another option would be to remove the drive from your Mac and place it in an external enclosure, which would essentially turn it into an external drive. You would then install a brand new drive into your MBP.
    It is possible that you could repair the drive with a stronger utility such as Disk Warrior. However, DW only repairs the complex software on your drive--it cannot repair a drive which is beginning to fail, which could well be the case with yours. You don't say exactly which MBP you have, but the average useful life of a laptop hard drive is 3-5 years, and many fail within the first year. Often the kind of problems you are seeing are due to a drive beginning to fail, so your first priority will be to get your data off of the drive.
    Since you were also seeing slowness, I suspect that your hard drive is headed south. If so, there wouldn't be much point in reformatting. It would just destroy your data, and your drive may still not ever work properly again. You can get a new drive for less than the price of Disk Warrior, although it's possible that DW can fix the corruption on your drive, at least for a while.
    Also, how full is your drive? If too full, that could be a contributing factor.
    If you do decide to try Disk Warrior and succeed in getting up and running, you should run SMART Utility:
    http://www.apple.com/downloads/macosx/systemdiskutilities/smartutility.html
    You can download the demo and run it several times for free. It will give you a comprehensive view of the physical health of your hard drive.
    What I would recommend is that you try FWTDM first and try to get everything off of the drive that you care about. If the drive is failing, it could fail completely at some point, so getting your stuff off of it is your most important priority.
    If FWTDM doesn't work, then the next thing to do is to remove the drive and put it in an enclosure and see if it will mount that way.
    The newer unibody Macs are designed so that you can replace the hard drive yourself. If you have an original MBP, you may want to get an AASP to install a new drive and give you the old one back in an enclosure. If you are under warranty, this won't void your warranty. If you are under warranty, Apple will replace a failed hard drive, but you won't get to keep the old one.
    If you are out of warranty, you could consider replacing the drive yourself using the directions at ifixit.
    Once you have gotten out of this fix, it's time to set up a backup strategy.
    Good luck! Post back if you have further questions.

  • My MacBook Pro is on, and with full batery but the screen does not turn on, only the keyboard does. what can I do?

    Please help!

    Call Apple Support and schedule a appointment for a hardware check, or take it into a Apple Store.
    We can't help you with that problem.
    Good Luck

  • On start up I get grey screen with wheel turning but it goes no further

    On start up I get grey screen with wheel turning but it goes no further

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
         a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, boot from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.   
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • My MacBook Pro is stuck on grey loading screen with apple logo and spinning wheel.

    PLEASE HELP - Tried to start up my MacBook Pro and I get grey screen w/ apple logo & spinning wheel. It's stuck on this screen. Safe mode didn't help but reveled this: smc read key action error, BOOS key failed, BOPS key failed. Consider rebuild of prelinked kernal com.apple.kext triggers triggered rebuild. IOBluetooth host controller USB transport Suspend Device. I ran verifications/repairs in Disk Utilities, but nothing came back wrong on the reports. I'm a bit panicked, as I use this computer for work and have no other computer to use in the meantime. I should also note that I have very little technical knowledge, so if you can lend your help please keep that in mind when responding. I'd be over the moon if anyone can help.

    Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
    Startup - Gray Screen
    Startup Issues - Resolve
    Startup Issues - Resolve (2)

  • I replaced the screen on my late 2007 laptop, now it won't boot. It Bongs and the wheel turns and then it turns off. I have tried a tech tool pro 3 disk, no results tried the osX tiger disk no results but bong and wheel. any ideas?

    I replaced the screen on my late 2007 laptop, now it won't boot. It Bongs and the wheel turns and then it turns off. I have tried a tech tool pro 3 disk, no results tried the osX tiger disk no results but bong and wheel. any ideas?
    I have not tried disk warrior yet,but will. I had it stored until I could get screen, battery is dead, and to be honest I forgot which OS I have in it, If I can Get screen up maybe I can get my info.
    sbckr

    Hi there sbckr,
    You may find the troubleshooting steps in the article below helpful.
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/ts1367
    -Griff W. 

  • I have a white screen with the apple logo  upon startup. Then the wheel turns and the screen is white.  Can't get past it.

    I have a white screen with the apple logo  upon startup. Then the wheel turns and the screen is white.  Can't get past it.

    Boot with your install disc, launch Disk Utility, and repair the boot volume.

  • TS1367 My MacBook turned on but is stuck on the white screen with the apple and the loading circle.

    My MacBook turned on but is stuck on the white screen with the apple and the loading circle.

    Hi there Mpontari,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/ts2570
    -Griff W.

  • IPhone 4 is stuck in the telephone screen, will not turn off by holding down top button or main menu

    iPhone 4 is stuck in the telephone screen, will not turn off by holding down top button or main menu, can't send texts, emails, check internet etc.,

    Hold down the home and power buttons until the Apple logo appears(about 15 seconds). It should then restart.

  • MacBook will turn on to white screen with gray apple and loading bar, will load very little and then turn off. What do I do?

    MacBook will turn on to white screen with gray apple and loading bar, will load very little and then turn off. What do I do?

    Bescobar23,
    which model MacBook do you have, and which version of OS X is installed on it?

  • My macbook is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page what do i do?

    My macbook Pro is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page with language select what do i do? Also i dont have enough monet to go to the apple store to get it fix and another thing this happen after i tried to factory reset it without the disck uising coomans i found on youtube.Lastly befor doing the comands my macbook would open any applications and the finder would just blink on and off on the dock.
    Heres the link http://www.youtube.com/watch?v=Q5e5thk0O9o

    Shut down your computer and disconnect all peripherals (keyboard & mouse if pertinent) from your computer.  Now reboot.
    If the Mac starts up normally, shut it down again and then plug in one of the peripherals (keyboard or mouse first) and start up your computer again.  If it does so successfully repeat the process, adding one peripheral at a time until your Mac acts up.  At that point, disconnect the last peripheral you added, reboot your Mac and search the peripheral vendor's website for an updated driver. 
    If no driver exists or the problem remain after installing the new driver, try a different cable or a different port on your Mac.
    If none of the above works, again disconnect all peripherals from your Mac, hold down the "shift" key to start up in "Safe Boot" mode. 
    If the Mac starts up correctly, restart without pressing the "shift" key.
    If your computer still does not start up properly, shut it down and restart it while holding down the Apple+Option-P-R keys; keep holding "all 4 keys" down until you hear the startup sound "twice."
    If none of the above work Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
    Select your language.
    Once on the desktop, select Utility in the menu bar.
    Select Disk Utility.
    Select the disk or volume in the list of disks and volumes, and then click First Aid.
    Click Repair Disk.
    (If Disk Utility cannot repair, you will need a stronger utility (3rd party) - Diskwarrior or Techtool PRO)
    Restart your computer when done.
    Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
    Remove any 3rd party ram.
    Reinstall Leopard - This will install a "fresh" copy Leopard without archiving old system files but leaves the rest of your files in place.
    If you still want to restore your computer to factory level...
    Start up from your install disc, go to Disk Utility and select the disk and click erase - to securely erase data click Security Options and Erase Free Space which will entirely wipe your disk, overwriting it with zeros so that no data is recoverable.
    To restore read the instructions in the Mac OS X v10.5 Leopard - Installation and Setup Guide  PDF

  • Why is my Snow Leopard 10.6.8 suddenly giving me a gray screen and progress bar after I've turned it on? The progress bar takes 4-5 minutes to complete then signing on with my password and all other operations are normal. Solution? Many thanks.

    Why is my Snow Leopard 10.6.8 suddenly giving me a gray screen and progress bar after I've turned it on? The progress bar takes 4-5 minutes to complete then signing on with my password and all other operations are normal. Solution? Many thanks.

    It's starting in safe mode > http://support.apple.com/kb/HT1564
    First of all, do a PRAM reset. If it doesn't help, open Terminal and type:
    sudo nvram boot-args=""

Maybe you are looking for