Stuck on Startup screen with 10.5.2

I've tried to install the 10.5.2 update on a G5 iMac ppc, but get stuck on the white startup screen with the apple logo. I've tried re-installing (archive and install) successfully, then applied the 10.5.2 combi update, with the same result. Am I stuck with 10.5.1?

I was able to get past the Apple logo startup screen lockup by repairing my directory with DiskWarrior.

Similar Messages

Mac Stuck at Startup Screen with Grey Apple Logo,Empty Progress Bar and a Spinning wheel

Last night the electricity went out and my power surge protector was not working so my iMac just force shut downed.
So, when the electricity came back i turned on my Mac but it is *Stuck in the Startup/Boot Screen with a Grey Apple Logo,a Empty Progress Bar with stays for 1 or 2 minutes and a small Spinning Wheel which would Spin Forver! I Have tried the SMC and Pram reset but no use, i have also tried to insert my OS X Lion 10.7 Installation disk and it would not load if i hold the C Key in the Startup, I Have Managed to go to Disk Utility Through "Recovery HD" but the Volume "Macintosh HD" is Greyed out and Unmounted and i cannot repair it. There are some files that i'd like to Recover if there is a way to fix it without deleting files.
**PLEASE HELP ME FIX THIS!**
Details about the iMac:
iMac 21.5 Inch i think from Mid 2010,
OS X Lion installed maybe 10.7.2 or 10.7.3 (im not sure)

kernel
Grey screen with Metallic Apple and spinning gear
Sounds to me like your hard drive failed on you as a result of the power going out.
http://www.apple.com/support/imac-harddrive/
If your iMac is a Mid 2010 you qualify for the hard drive replacement program from Apple.
Apple has determined that certain Seagate 1TB hard drives used in 21.5-inch and 27-inch iMac systems may fail. These systems were sold between October 2009 and July 2011.
I hope I helped you with your problem.
- Brandon

IPhone stuck on startup screen, crashes iTunes when I connect

I'm running an original iPhone. I upgraded to v2 of the OS when it came out, and was running apps with no problems until today. Today I bought a couple of new apps. When I connected the phone to my Mac, it backed up, updated the apps, and ran fine for a while. Then I tried one of the new apps (Grocery List). It didn't run. I tried it again. It crashed my phone. I'm stuck on the startup screen (with the centered Apple logo). I've tried rebooting, but I can't get past this screen. iTunes runs fine on my Mac laptop until I connect the phone, at which time I get the spinning beachball. My phone is stuck on the startup screen, and is getting real hot.
Any suggestions? Thanks.

Same frustrating boat. Attempting to force a restore as I type this out. iPhone was fine all since the 2.0 update, and did the 2.0.1 update earlier today. All seemed fine throughout the day. And at the end of the day I decided to delete an app from my iPhone and then decided to restart. That's when the apple logo stayed on the screen for what seemed forever. I've noticed it taking a while in the past, but I let it "work" for about 5 minutes and still the same apple start-up screen. Tried a force restart which did no good. Now as it's restoring I keep thinking about how long it's been taking to do a backup of the phone and so I usually just skip it.
Granted there will always be growing pains when you let hundreds of other developers all "play on your playground" at once (referring to the app store), but I can't help but feel that Apple better (great itunes just told me that the backup is corrupt) fix these problems quick as they're losing the faith of new customers and even loyal early adopters.

MacBook Pro won't get off startup screen with apple logo. Help?

Could someone please tell me how I can get my macbook to get off that stupid startup screen with the apple logo? It won't go past that screen and boot properly. I have tried reinstalling OS X didn't work. I tried running a disk utility test and no errors where found. I don't have the time machine thingy so I couldn't try that. Is there anything else I can do before taking it to Apple and l
paying hundreds of dollars???
thanks in advance!!!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Macbook Pro stuck at startup screen.

I've ran Disk Utility, there were problems that were fixed, but it's fine now (I've ran it again to double check), and I've ran Apple HHardware Test and I received" no trouble found".
But everytime I try to start up it gets stuck on the grey startup screen with the apple and the oration under it. So I'm at a loss at this point.
Thanks for any help you can offer.

System files are missing or damaged so you need to reinstall OS X:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
If you have an earlier version of OS X installed then do this instead:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Upgraded to Network Monitor 1.2 - Stuck on Startup Screen

After upgrading to Network monitor 1.2 it is stuck on the Startup screen with the circle only 7/8 of the way around.
I have rebooted the computer and still get the same issue.
This topic first appeared in the Spiceworks Community

I was able to get past the Apple logo startup screen lockup by repairing my directory with DiskWarrior.

Intel-based iMac stuck in grey screen with spinning wheel. SMC::smcReadKeyAction ERROR THOP kSMBadArgumentError(0x89)

Hi guys,
since yesterday my Intel-Based iMac doesn't boot normally, its stuck in grey screen with a spinning wheel.
Its an Intel-based iMac 21.5'' purchased in 2011, and i recently (2 months ago) upgraded it to Mavericks.
-2 weeks ago, i installed smcFanControl app
-Tried start up in Safe Mode by holding Shift but its not working. i think i hear fans are working more than they were before the problem occurs.
-entered Single User Mode and i get an error
SMC ::smcReadKeyAction ERROR THOP kSMCBadArgumentError(0x89) fKeyHashTable=0x0xffffff8029fa1000
-followed some instructions found online, but can execute the correct commands in SingleUserMode
tried to remove FanControl as explained here: http://apple.stackexchange.com/questions/110667/errorr-kernel-smcsmcreadkeyactio n-in-console
any ideas what may caused this and how can i fix this?
Thanks in advance

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, boot from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My macbook pro is stuck on grey screen with apple symbol in center with the progress circle under it continusly spinning. After I had turned it on. Prior to turning it on I had to force close and shut down a few hours prior. Please Help?

My macbook pro is stuck on grey screen with apple symbol in center with the progress circle under it continusly spinning. After I had turned it on. Prior to turning it on I had to force close and shut down a few hours prior. Please Help I have tried everything I know to do

Unfortunately this means that there is a problem in the boot sector of your hard drive. It might be indicative of a fundamental corruption in the coding that allows your computer to boot your operating system from your hard drive. I had this problem twice and it resulted in me having to get a new hard drive and restore my data.
In other words, your computer can't talk to your operating system so you can't access your data.
Here is my advice: DON'T CALL APPLE TECH SUPPORT though they are kind and usually helpful it will take you an hour just to explain the situation and they will only tell you to do what I'm gonna say here.
First: Shut down your computer completely
Two: boot up while holding down the following keys: command, option, p, and r. The computer will reboot 3 times. This solution will likely fail so if you're frustrated skip to the next step.
Three: Boot up while holding down the option key. Select recovery drive. Select your default language. Select disk utility, click on Macintosh HD, and select "verify and repair volume." Likely the verification will produce some line like "unused node not erased." Or something like that. If anything using the words "node structure" comes up, you need a new hard drive.
If after verification and repairs you still can't boot I sincerely hope you have apple care because you will need a new hard drive. Set up an appointment to come in to the apple store, they will tell you to go and get data recovery, just ask them to give you the old hard drive. Unless you have an up to date backup in which case you can just restore from that. If you're lucky the only issue is with the boot sector which means that if you ask them to give you the old hard drive, you can buy an enclosure and you have effectively been given a free external hard drive. It still works to store data just not to load an operating system.
If you have a back up drive bring it to the apple store and they'll do the whole thing right there, it should take around an hour and a half but may take longer.
Hope this helps, it's annoying but it's your safest bet.
All the best.

Installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug. is this corect? I am unable to use the phone now. What should i do next? I plug in to itune in my computer and ask me to restore my phone?

installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug.
I am unable to use the phone now. What should i do next? I plug in to itune in my computer and ask me to restore my phone? I will loose all my date?

I hooked up itune and restore. after finished restores, it said my phone is in recovery mode and needs to be finish before using itune, my screen still show the itunes icon and power plug

Last night i was downloading the new update for the Iphone, and after the download was done and trying to install, it errored out. And now my phone is stuck on the screen with the itunes icon and the USB.

Last night i was downloading the new update for the Iphone4 on my laptop through Itunes. After the download was done, it was starting to install, and then an error came up and didnt get a chance to check it. Now my Iphone is stuck on the screen with the USB pointing to the Itunes Icon and wont do anything else. Any advice on how to get this fixed, or do i need to go to the Apple store and have them look at it.

slawdog31 wrote:
Is the sleep wake button at bottom center of the Iphone or on top?
Top
iPhone User Guide

HT1222 i installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug. is this corect?

installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug. is this corect? I am unable to use the phone now. What should i do next?

I hooked up itune and restore. after finished restores, it said my phone is in recovery mode and needs to be finish before using itune, my screen still show the itunes icon and power plug

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

Maybe this might help.
http://support.apple.com/kb/TS2570

I just finished downloading and attempting the install of ios 7 on my iPhone 5. I'm using the newest version of iTunes. And now, I'm stuck at the screen with the iTunes logo and the plug. But no matter what recovery mode wont work

I just finished downloading and attempting the install of ios 7 on my iPhone 5. I'm using the newest version of iTunes.
And now, I'm stuck at the screen with the iTunes logo and the plug. But no matter how many times I try, recovery mode will not work. My phone is currently useless unless I can figure this out.

No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

My iphone 3gs will not retore. Error 3194 keeps popping up and my phone will not turn on. Its stuck on a screen with an itunes logo

Can someone please help me with retoring my iphone 3gs. Error 3194 is constantly popping up. My phone is stuck on a screen with an itunes logo and an apple cord

Make an appointment at an Apple store if there is one nearby.

In the process of reseting phone and got stuck on black screen with spinning logo

in the process of reseting phone and got stuck on black screen with spinning logo
what do I do

Hey amreed2012,
Thanks for the question. The steps in the following resource may resolve your issue:
If you can't update or restore your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT1808
Thanks,
Matt M.

Stuck on Startup screen with 10.5.2

Similar Messages

Maybe you are looking for