Stuck on the login screen

nm
Solved!
Go to Solution.

Just hold it until it vibrates ONCE
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Similar Messages

My MacBook Air is stuck on the login screen, each

My MacBook Air is stuck on the login screen, each time I enter the password it stops (but does reject an incorrect password)

Restore OS X.
If your Mac has v10.7, v10.8, or v10.9 installed, startup your Mac while holding down the Command + R keys. From there you can restore OS X using OS X Recovery
For OS X prior to v10.7, boot from your install disc while holding down the C key.

I turned on filevault but after restarting i got stuck at the login screen.

I turned on filevault but after restarting i got stuck at the login screen. my trackpad is working but not clicking. i tried random keys and finally got to enter my password via keyboard. now i am afraid of shutting my mac , what to do?

There is a known problem and I am having exact same issue. Power cycling and internet cache does not fix the issue. When a connection to a server fails it has nothing to do with caching issues. It is a network issue on AT&Ts end in a localized region. It works in multiple towers in various locations but does not work where I am. I have reported this to AT&T.

Macbook Pro stuck at the login screen

This morning I dropped my laptop by catching the charging cable the laptop fell on the floor but everything seemed to be normal.
I then decided to back up straight away so I started time machine. I stupidly started doing some user instensive things on my mac whilst this was going on e.g. playing a game which can sometimes crash. When it did crash I left it for half an hour or so to see if it would bring up force quit or switch out of the crashed programme. This didn't happen so, like i've done in the past, I hard reset holding down the power button.
When I turned on the mac everything seemed normal I got to the login screen and it offered to startup the computer as it was before I restarted. This was a bit odd as I normally get this message when i've actually logged in. My Backup drive also asked for a password which was also strange for the same reason. I then attempted to login to the computer I typed my password in. It was accepted and the screen went white and then went back to the login screen.
I repeated this a few times, restarting etc before I tried using disk utility in recovery mode. When verifying the disk no problems were found. Disk permissions found two problems, which unfortunately I can't remember (1 was to do with the library), I then repaired disk permissions. I tried to start again but got the same problem.
I then stared in safe mode. I'm now meant to be in safe mode but i'm not 100% sure as everything seems the same except everythign is very slow.
Midbackup my computer crashed so i'm wondering if there are any problems there (especially as it was the first backup I made on my new external HD). I'm now trying to backup in safemode but i'm not sure if that's the best thing to do (as not everything might not copy over and I could potentially ruin the first backup to my new external HD). Can anyone give me any advice on what to do next, tell me where I can test whether i'm in safe mode or not and let me know if I should be backing up in safemode.
Thanks in advance
Alex
Macbook Pro August 2011 13 inch
500GB HD
4GB RAM
2.3 GHz Intel Core i5
Lion 10.7.3
UPDATE
After entering successfully what appeared to be safe mode, I restared the computer and tried logging in normally. I got the white screen (as normal) before I reached the login screen, and after entering my password it eventually did log me in. Everything seems normal but I still want to be sure. My computer seems very slow. I only have 1.25GB/4GB free of RAM and I only have two safari tabs open. I'm backing up now but i'm still a bit concerned.
Message was edited by: Alexander Richardson

there is no installation cd, i have hit the command r function and attempted to reinstall from the recovery option stored on the computer. I am connected to the internet. It keeps saying downloading extra components and then once completed just goes b ack to main screen with my old log in informaiton as if nothing has happened. I also attempted to try to do a back up from a restore log and nothing on that as well.

After 10.5.2 install stuck at the login screen. Help please!

Hi all,
After installing 10.5.2 my computer rebooted to the login screen, but no matter what account I select (I have 3) it goes to a blue screen for a few seconds and then right back to the login screen. I've tried booting in safe mode and also resetting the PRAM. I've been reading this forum, but don't seem to see anyone else having this same exact problems.
Any suggestions?

I have had problems after the 10.5.2 update. I ended up with a frozen computer - unable to restart or shut down etc. Also ended up at one stage with Set Up Assistant screen. With the help of a computer savvy friend, at least I am able to use my computer again.
It appears the actual download did happen but it did not install and the computer tells me I need to "re-start". When I did this, window appeared on plain blue screen saying it was installing software but absolutely nothing happened - no blue scrolling bar etc.
My iMac computer is still under Apple Care Plan and technician told me they are many problems surfacing across the various machines with this upgrade. He has asked me to delay updating the software and to ring back in a couple of days because their technicians are currently working on the problem and he hopes for an answer soon.

I am trying to log into my account but get stuck at the login screen

Whenever I try to log into my account it starts thinking for a minute or two and then brings me back to the login screen.Is there something wrong with the account access?

There is a known problem and I am having exact same issue. Power cycling and internet cache does not fix the issue. When a connection to a server fails it has nothing to do with caching issues. It is a network issue on AT&Ts end in a localized region. It works in multiple towers in various locations but does not work where I am. I have reported this to AT&T.

Polycom CX500 stuck on the login screen !

Hello ladies and gentlemen :)
Recently bought a Polycom CX500 and I literally want to commit a suicide because of this phone ! Can someone help me or guide me how I can bypass the lync setup or tell me how to access the menu of this phone ?
My problem is that I don't have a lync account and when the phone boots up it asks for an extension or phone number -> then the PIN number !
Any other ways to login or skip this step ! The phone is currently running on firmware version 4.0.7577.4372.
I just want to enter the phone menu and check its parameters and what can be done, but since I can't actually get into the phone, don't really know how to deal with that.
Thanks for your time and help.
Dementor H

Hello Dementor H
the CX500 unlike the CX600 and CX3000 do not have a USB port to bypass the LYNC PIN and Extension login method.
You will require to setup a DHCP server to provide Option 43, 120 and the NTP server.
Without that the phone cannot sign into LYNC. If you do not have an on premise LYNC server providing this the phone cannot be used. There is no Menu where you could add any details once the phone has signed in.
Best Regards
Steffen Baier
Steffen Baier Polycom Product Support Specialist, EMEA Escalations

My Computer is stuck on the login screen!!!!! HELP!

i help down command+v during startup to see what was going on, and i get stuck on this command:
Jan 20 20:22:27 KYII com.apple.launchd[1] (com.apple.mDNSResponder[19]): posix_spawnp("/usr/sbin/mDNSResponder", ...): No such file or directory.
My computer was working fine and i shut it down, and then this occured when trying to start it up. hoping someone can tell me whats wrong. Thanks a lot, Kevin

im getting this same error on my old PB G4!
i did a new install of 10.5, then combo update to 10.5.6 and software update, so far all worked.
then i set up sharing and some sys pref params. after shutdown i cannot restart and get the above error (in single user or verbose mode)
the HD does not show any errors with diskutility, i did a PRAM reset. i erased the HD completely, reinstalled the OS, but the same error happens: spinning wheel and mDNSResponder file not found.....
any hint is appreciated

Problem starts with version 3.6 & later. webpage stuck on the login screen instead of open the subsequent pages.

do not have this problem with either IE or Chrome or earlier firefox. after loggint into the webpage(my work site), the page refreshes itself instead of opening to the secured pages.

Clear the cache and the cookies from sites that cause problems.
* "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
* "Remove the Cookies" from sites causing problems: Tools > Options > Privacy > Cookies: "Show Cookies"
If clearing the cookies doesn't help then it is possible that the file cookies.sqlite that stores the cookies is corrupted. 
Rename (or delete) cookies.sqlitecookies.sqlite-journal and cookies.txt, if they exist, in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder] in case cookies.sqlite got corrupted.
* http://kb.mozillazine.org/Cookies#Removing_cookies

Can't get past the login screen - Login fails [SOLVED]

Dear Arch community,
I have just installed xfce4. To make it perfect, I've installed slim and added it to the daemons. It works flawlessly...unfortunately I am not able to login. It does not seem to recognize my user name and/or password. After going back to the prompt (strg+alt+F5), I am able to login. Also: If I log in and try to go back with srtg+alt+F7 I am stuck at the login screen again.
The problem:
Slim is not able to access user and password - How do I get it to do so?
On the other hand...from my point of view it could be anything.
Any help is very appreciated.
Last edited by 3xp10r3r|X13 (2012-08-26 18:05:14)

3xp10r3r|X13 wrote:
all I've got in it is:
exec xfce4-session
I guess that is a bit too less.
Actually according to the wiki it should be just
exec startxfce4
when using slim. Have you made your .xinitrc executable?
chmod +x ~/.xinitrc
Last edited by bgc1954 (2012-08-26 16:18:53)

So on my MacBook Pro, a friend tried signing into the guest account. It's been stuck on the loading screen for 3 days and hasn't let me cancel the request and login to the original account. What can I do?

So on my MacBook Pro, a friend tried signing into the guest account. It's been stuck on the loading screen for 3 days and hasn't let me cancel the request and login to the original account. What can I do?

Hold the power button down for 10 seconds. It will power down your Mac. You can then start it up again and see if you can log in normally.

I updated my MacBook Pro, and now it's to fully restarting.. It's stuck on the grey screen with the loading sign at the bottom of the apple.

How do I fix this issue???

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

I have the same problem - it is maddening. I rely on this iPad for work so this is not just an annoyance! The above solutions of changing the appleid on the device or on the website do not work.
The old email address no longer exists - I haven't used it in a year probably and I no longer have the account. I logged into the appleid website and there is no trace of the old email address so there is nothing that can be deleted or changed there. On the iPad there is no trace of the old email address so nothing can be deleted there either. I have updated the iPad software and the same problem comes right back. Every 2 seconds I am asked to log in using the old non-existent email. The device is currently useless.
The only recent change to anything was the addition of an Apple TV device, which was set up using the correct login and password.
Does anyone have any ideas? The iPad has been backed up to the iCloud so presumably it now won't recognize the current iCloud account? So restoring may notbe an option?

My MacBook is stuck on the loading screen. Please help! Not sure what to do

Hi, so my MacBook has stopped working for some reason
I've just tried switching it on but it has stopped on the loading screen.
I am scared and not sure what to do.
Please help!!!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

My nephews iPad Mini is stuck on the lock screen. It's frozen and you can't slide the unlock bar. I tried rebooting it and it didn't work. What can I do to fix it?

My nephews iPad Mini is stuck on the lock screen. It's frozen and you can't slide the unlock bar. I tried rebooting it and it didn't work. What can I do to fix it?

How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

Stuck on the login screen

Similar Messages

Maybe you are looking for