Stuck with Management mode firmware upgrade..see pic

Management Mode
Firmware Upgrade
File Name:___________________  Browse
Apply    Reset
How do I get around this.  I upgraded to WRT54Gv5v6_1.02.5.002_fw.bin and now when I reboot this is all I get.  If I try to go to another version I don't get connectivity.  I only have connectivity for this part then I lose it. 
Every time I type in 192.168.1.1  I always get this display....
I've tried to hold the reset up for 30sec the first time then 1min.......then unplug for 10 to 20 seconds, (still holding down the reset button) and reconnect.  Letting go of the reset button once it's connected.
Is the router gone?  Will I have to get another one?  Would like to get your input.
Thanks

Download firmware file again. And browse for it, and upgrade it. Reboot router, it might work.

Similar Messages

  • I was trying to update sofwatare for my iphone 4s, i got stuck with recovery mode and only option i see is to restore from factory setting. Do i lose all the the datas ? i did't had any backup. What is a solution?

    I was trying to update sofwatare for my iphone 4s, i got stuck with recovery mode and only option i see is to restore from factory setting. Do i lose all the the datas ? i did't had any backup. What is a solution?

    If you didn't back it up, your data is gone. There is no "solution" after the fact.

  • Stuck with run mode

    Hi
    I am stuck with run mode on one of my VI (I can't edit it or even see the diagram). here's what I verified
    1. tools>option>miscellaneous> I uncheck "Open VIs in run mode"
    2. I hit Ctrl+M, it is still in run mode
    3. I close LabVIEW and reopen, it's still in run mode
    4. I check the VI file type, it's not a read only
    Do u have any idea about how I can go back to edit mode to modify the diagram? I'm using LabVIEW 7.1
    Thanks

    Without having the VI in front of me it is difficult to say exactly what settings you have turned on.
    I would suggest trying the following things to get your VI out of run mode.
    1) Ensure that "Open VIs in Run Mode" is turned off in Tools->Options->Miscellaneous
    2) Open the VI by dragging it into another block diagram and double clicking on it
    3) With the VI open hold down control and press the '.' key. This is the same as pressing the "Abort" button.
    4) Hold down control and press 'M' to switch out of run mode
    If you can reproduce the behavior in a VI which you are able to post on the forum, I am sure we will be able to figure out what steps are needed to edit the VI.
    Scott Yellig
    Applications Engineer
    National Instruments

  • HT3529 My iphone 3GS is stuck in recovery mode since upgrading to ios 5 and still, after upgrading to ios 6.  What's up ?

    My iphone 3GS is stuck in recovery mode since upgrading to ios 5 and still, after upgrading to ios 6.  What's up ?

    I just went through this yesterday and because i am no where around my computer i lost everything and now my battery drains very fast...you are going to have to recover your phone  i hope you have everything backed up and are next to your computer...if you are push and hold your home button and plug into PC at same time and continue to hold the home button untill you see your USB on your pc screen light up (depending on what type of pc maybe i dont know what you have)
    push home button
    Plug into pc usb
    usb on pc screen lights up..let go of home button
    follow instructions for restore/sinc
    hope it helps

  • IPhone 5 stuck in portrait mode after upgrade to iOS 8

    iPhone 5 stuck in portrait mode after upgrade to iOS 8.
    Phone was fine before the upgrade, iOS 8.1 did not fix the issue.
    Have done a factory reset at Genius bar and they say it's a hardware issue and have gotten this response below:
    "Now, when you perform an update to any iOS device many system checks are run to verify that all components are working as they should. This is part of the firmware update process. When these checks are run sometimes issues are detected, even if all seemed to be running well previously. When this happens one of two things can occur. Either the hardware will be deactivated completely, or it will be locked in a state of use so that the device can still be used. In the case of the gyroscope for screen rotation, the firmware locks in place so that while not perfect, the device can still remain on some functioning level. This is what appears to have happened when you updated. The software itself did not cause any failure, but it detected a currently upcoming issue and prevented it from becoming worse."
    All I want is a replacement but they want me to pay £199 since it's out of warranty.
    Anyone have the same issue?

    If the device is out of warranty you must pay the out of warranty replacement fee to have your iPhone replaced. If the phone was still under warranty the phone would have been replaced at no charge.

  • IPhone 3gs stuck in recovery mode, firmware iO 5

    My iPhone is stuck in recovery mode. I have a 3gs, firmware 5.0.
    Before I tried to restore it, my iPhone would randomly shut off, turn back on, and display a notification that said "Activation Required." Now, sometimes my phone would shut off again and return to it's previous working state. However, this time it did not. I put the phone into recovery mode and tried restoring it on my Acer Aspire 1 with Windows 7. iTunes put the phone through the various stages of restoration; Extracting Software, Preparing iPhone for Restore, Restoring Software, Verifying Restore, Restoring Firmware. After all of this, a nice little error message pops up that reads, "The iPhone 'iPhone' could not be restored. An unknown error has occured (1)."
    After this little mishap occured four more times, I decided to click "More Information," and was promptly brought to the help page set up here. I proceeded to troubleshoot by updating to the latest version of iTunes, updating my security, restarting my computer, and so forth until all the necessary precautions were performed. Now it was back to iTunes to try my luck at getting my life back.
    To my delight, I found that this time the restoration process took upwards of forty minutes to complete. However, to my despair, a nice little error message popped up that read, "The iPhone 'iPhone' could not be restored. An unknown error has occured (-1)." Ah, a different error message! i thought, feeling as if there was hope in fixing my phone. I clicked "More Information" and skimmed through the specific error messages, looking for that lucky -1. Nothing.
    I need help. I have attempted to restore my phone a dozen times since this occurence, and I'm growing tired of going through the same process over and over and getting the same result. My phone is stuck in recovery mode now. I've tried restoring the phone on 2 different computers, to find out if, in fact, the problem was my iPhone and not my computer.
    Some important information you may need to know in order to help me solve my problem:
    iPhone 3gs
    Running iOS 5.0
    Using iTunes 10.5
    On an Acer Aspire One Netbook
    Running Windows 7
    All security updates installed as of November 7, 2011
    Also iTunes 10.5 on Acer Aspire 57354774 laptop
    Running Windows 7
    Reply ASAP with a solution please!

    Hello,
    I have an iPhone 3GS which I updated with the last firmware (iOS 5) 2 weeks ago. Everything goes ok.
    And suddenly, while the phone was recharching. It asked me to activate it but I was unable to do it as it was rebooting constantly every time I connected it to iTunes.
    I tried both 2 restore modes (Restore and DFU) but since I can't achieve a restore with the last Apple iOS 5 firmware. I got the error code 1.
    I I tried on 3 different computers but same error. I really don't know what to do next...
    I already called Apple Customer Care and I'm still waiting for an answer. I let you know.
    And you, did you manage to get your iPhone back alive ?

  • HT4528 Iphone 4 stuck in recovery mode during upgrade to ios 7 software. How to get it unstuck without losing data. Thanks.

    I tried to upgrade my Iphone 4 software to ios 7.It then got stuck in recovery mode.  I tried to work with Itunes but screen said phone was in recovery mode and had to be fixed in order to use itunes.  I would like to know how to get in Unstuck without losing my current data, if at all possible. Thanks in advance for your help.

    If the phone is in recovery mode, the access to the data is already lost. See this support document to restore your phone. http://support.apple.com/kb/HT1808
    IF you did the update via iTunes, the first thing iTunes would have done was to create a backup. Check and if it did, then you can restore to that backup.
    Message was edited by: ChrisJ4203

  • Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

    Hi,
    I upgraded my device after I got an email that there is a new firmware:
    An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
    I installed the update but now it is stuck at 95% after rebooting.
    Never had any problem before the firmware upgrade. 
    Any advice?

    Hello BelgianTomas
    I recommend that you first power down the unit if the unit has not completed the boot process.  Then re-seat all disks and try booting the unit again.  Please do not try to access the web interface until the power led is solid white.
    Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot. 
    If that does not help, LenovoEMC suppor should be contacted for more advanced options.
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • Problems with the latest firmware upgrade

    I found a problem with the 01-10-2006 firmware upgrade. Now that it is inside my ipod certain videos don't play properly anymore. Actually the video starts, it plays normally for a while and then it goes still for a few seconds and then, when it plays again, the audio is gone.
    It always happens in the same point with the same video. In particular, just in case someone wants to try, it happens in the latest nasa video podcast.
    I don't know what to do!
    I'll try to step back to the 1.0 version...

    I'm having this problem as well. Sinse I updated the firmware all of my movies get stuck about every 10 seconds then if I wait a few seconds they start up again but with no audio. I'm quite certain that this is a problem with the firmware sinse the videos play fine on quicktime, they used to play fine in my ipod before I updated it, and I can get it to play the parts it gets stuck at if I rewind it but it happens very frequently and each time takes a while to reload. If anyone has found a way to solve this problem please let us know.

  • Ipad2 stuck in recovery mode following upgrade attempt

    Hello,
    I tried to upgrade my iPad (after endless prompts from Apple) but it fails near the end, and is now stuck in what I guess is "recovery mode".  I see a symbol of a plug and the red iTunes icon.  I do not want to restore the whole iPad - I have no idea whether my things are backed up on iCloud - because that usually gets some sort of error message too.  How can I just get the thing to unfreeze and go back to the operating system?
    Many thanks,
    Patricia

    Yes, there is a way to get out of Recovery Mode. This link is to an Apple Support page that describes the steps to take to get your iPad working again.
    Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
    Once the iPad has been Recovered you can restore your data from a recent backup if you have one. If you don't periodically backup your iPad this is a good lesson into why you should. All computer and computer like devices can experience problems where data loss occurs.
    If you do not have a backup, you can recover all purchased or downloaded apps and music without paying for them again as long as you use the same Apple ID that you used to download the stuff originally.

  • IPhone 5 stuck in recovery mode while upgrading

    While upgrading my iPhone 5 to ios 8.0.2, my phone got stuck in recovery mode. Tried with iTunes and it says it is still in recovery mode. First complete it and then connect with iTunes. Finally got Error message 3194. I am using latest iTunes. Phone is stuck with iTunes and connector symbol on the screen.

    Me too. I now have to restore my entire phone and lost a whole bunch of info. So angry with Apple lately.
    As an owner of all Apple products for computing and mobile since the 90's, I am starting to think about moving to Samsung phones. Apple is lacking in innovation and their products (and software) aren't the same quality. So sad.

  • HT4623 my phone is stuck in recovery mode, it has a pic of the phone telling me to connect to itunes

    Help!!! I have a 3Gs and it's stuck with a pic on it telling me to connect to itunes!!

    I still have the Same Problem. 

  • My iphone 4s stucks in recovery mode after upgrading to latest iOS7

    I tried to get out of this loop by pressing home and power buttons for 10 sec and releasing the power one, but it didn't help.. I even tried to restore to factory settings! but it is interrupted by error 9! it's been 3days i'm stucking with this, one of my friend said there would be a hardware problem with the battery! how is it possible and upgrade makes my iPhone such a sick piece ?!

    I tried to,,, but every time I get error 9 ! I tried with different cables and systems but it happens again... the restore can not be finished :~ someone checked my phone and told it could be a hardware issue with the battery! but how come!

  • SRW2024 Stuck in Loop after Firmware upgrade.

    When connected to the serial port the following continues to loop:
    ------ Performing the Power-On Self Test (POST) ------                                           
    UART Channel Loopback Test........................PASS
    Testing the System SDRAM..........................PASS 
    Boot1 Checksum Test...............................PASS
    Boot2 Checksum Test...............................PASS
    Flash Image Validation Test.......................PASS
    BOOT Software Version 1.0.0.03 Built  08-Jun-2004  09:48:10
     CPU - FireFox 88E6218 ARM946E-S processor                  
     64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...
    Decompressing SW from flash
    HOSTG_rscode_file_load: could not load file
     Perform WARM BOOT ...
    When I attempt to do download the new software with XModem the firmware (fw) completes successfully (ls20xx_Salsa-12222.ros) but the boot image fw fails (runtop_boot-101.rfb) and I receive this message:
        Startup Menu
    [1]  Download Software
    [2]  Erase Flash File
    [3]  Password Recovery Procedure
    [4]  Set Terminal Baud-Rate
    [5]  Back
     Enter your choice or press 'ESC' to exit:
    Downloading code using XMODEM.
     -- Download complete --
    Wrong file format. Writing aborted.
    Is there a different version of the firmware perhaps an older version available for download somewhere? Or is there something I am doing wrong?
    Any help would be greatly appreciated.
    We have 2 - srw2024's and 2- srw2016's. Issue only on the one with the fw upgrade.
    Thanks.

    Here is what I've found to be useful and so far seems like a fix for myself.
    I downloaded an older firmware version 1.0086 from here
    http://ip.gliebetronics.com:800/firmware/Linksys%20SRW2024/Firmware/
    runtop-10086.ros
    The other 2 versions may help some other people on this forum.
    Uploaded it through the serial port with Xmodem.
    So far I've been able to boot and now access through web interface. I will post later on how it is doing later in the day.

  • Help! iPad stuck in recovery mode while upgrading to v6.1.2

    I have a 6 month old iPad 64 GB Wifi. It was working perfectly till last week. Then I noticed that an upgrade to v6.1.2 was available and I initiated the update process (much to my regret).
    The upgrade failed and then it gave an error "iPad firmware error (-1)". I have tried all sorts of things like DFU Mode, pressing home button and power button together and still am unable to restore it.
    I went to a authorised service provider who said there is a 4mm dent on the iPad and that has caused all the problems. This dent occured a few months ago and the iPad was working perfectly throughout. The iPad hanged only when the software upgrade to v6.1.2 was done. The service provider says that it is in warranty but that has been denied due to the dent and they are asking me to cough up 520 SGD to replace it which is atrocious!
    Can anyone please advise on this?
    Thanks

    Suggest you try Recovery Mode a few more times.
    Recovery Mode
    1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
    3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
    Note: Data will be lost. You may have to repeat the above many times.

Maybe you are looking for