Sub-option code for a Cisco Aironet 1510 AP

What is the sub-option code that has to be delivered as part of a DHCP Option 43 response for a Cisco Aironet 1510 AP?
Thanks,
Adrian

i think you're looking for the following:
option 43 ascii
ie:
option 43 ascii "10.10.10.2, 10.10.11.2"
please see this link for more info:
http://www.cisco.com/en/US/products/ps6548/products_quick_start09186a00806b5d00.html#wp45319

Similar Messages

Cisco Aironet 1510

On the Cisco Aironet 1500 Series Lightweight Outdoor Mesh Access Point spec sheet from the Cisco.com website, it states that the input power for the DC inline POE is 28.5 W at 48 VDC, nominal. What is the maximum power at 48 VDC? On AC, the nominal power is 57.8W at 120 VAC. What is the maximum power at 120 VAC?
Also, I see that the Cisco 1510 only uses AC as a source. Does Cisco have a device for the Cisco Aironet 1510 that uses DC as a source? For example, instead of using the POE Injector that Cisco has, which uses an input of 120VAC (1.5A) and outputs 48VDC (1.2A), does Cisco have a POE Injector that uses an input of 12VDC and outputs 48VDC (1.2A).

I think the maximum draw (with both radios and heater on) is 57.8 Watts, but with the heater not active it's much lower around 36.84 Watts.

Cisco aironet 1510 AG

Hi everybody.
I was reading about cisco aironet 1510 AG and found it has two N series connector for antenna.
Cisco Aironet 1510AG
Expansion / Connectivity
Interfaces
1 x network / power - Ethernet 10Base-T/100Base-TX ¦ 2 x antenna - N-Series connector
1) we have two N series connector for antenna why do we need two antenna?
thanks and have a great weekend.

Hi,
Two Antennas are used for diversity. Because there are too many factors that may affect the RF signal (Refraction, reflection, etc), the signal will follow different pathes to reach the destination (called multipath). Having two antennas to send/receive will make the receiver hear two signals (or more). If one of the signals is malformed then error correction will be better this way. This will make it faster than requesting the re-transmit again from the sources.
802.11n access poins usually have 3 Antennas for each radios because they use MIMO.
Also, this link will give you better information about Diversity and Multipath distortion:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008019f646.shtm
HTH
Amjad

Need a Floorstand for a Cisco Aironet 1242AG WAP

Could you please advise us on a good floorstand for a Cisco Aironet 1242AG WAP?
We need to find a floorstand that would provide an effective mounting solution for our Wireless Access Point (Model Cisco Aironet 1242AG, images of the back and front are below). It should be at least 5 ft high (1.5 m) with pins/knobs or something to mount our WAP. Any ideas? Need answer asap.
Thank you for your help!!

Is the floor stand to do surveys or is it for a permanently mounting ? These normally are mounted to the celing tile.

Part codes for any Cisco part

Hi,
Any one knows in single file/url where we can check Part codes for any Cisco part.
I need mostly for SPFs modules.
Thanks
Venkat

http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL632702.html
http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/gbic_sfp_modules_install/5067g.html
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6578/product_data_sheet0900aecd801f931c_ps5000_Products_Data_Sheet.html
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6576/product_data_sheet0900aecd80582763.html
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/data_sheet_c78-455693.html

Client association between RAPs & MAPs (Cisco Aironet 1510)

How do you fix the association bugs that the 1510s have?
My problem is when a client (like a laptop) associates to the MAP (Mesh Access Point) or RAP (Rooftop Access Point), the client doesn't hand off it's wireless connection to the access point with the better signal strength. Is there a setting or configuration on the Wireless LAN Controller that would help this problem?

There are no issues roaming between RAP. Try upgrading the code of WLC to 4.0.179.8 and also try upgrading the client software since it is the client which should to access point with better signal.

[solved] Cisco Aironet 350 package

Hi guys,
Is there a package for the Cisco Aironet 350 anywhere? I have to set up a thinkpad x31 that has one, but I can't find any package for the driver, neither in the normal repo, nor in the AUR. Maybe it's too early in the morning ;-)
Last edited by rochus (2007-10-10 08:16:25)

omg I shouldn't wake up, go to the PC, turn it on, read some stuff and don't check the wireless drivers that ship with the kernel.
It's already there...

Cisco Aironet 3700 Autonomous Mode

Hi guys,
I was wondering if the autonomous IOS for the Cisco Aironet 3700 series is fully functional, instead of only supporting the site-survey mode.
Many thanks.

Thanks man.
I saw that IOS on Cisco's site too.
https://software.cisco.com/download/release.html?mdfid=285029866&flowid=48543&softwareid=284180979&release=15.3.3-JAB&relind=AVAILABLE&rellifecycle=ED&reltype=latest
However, I wasn't sure it fully supports it.
Cheers

DHCP Option Code Utility - the return

A long time ago I wrote a utility to make it easy for mere humans to generate the encoded values needed to define DHCP Option Codes for use with Apple's DHCP Server.
This utility was remarkably bug free and even as a 1.0 version worked with PowerPC and Intel Macs all the way from Mac OS X 10.4 to OS X 10.7.5 with zero reported bugs. It did however hit a problem with Mountain Lion 10.8 which I have finally got round to investigating and resolving. It turns out Apple made a change that broke the way my utility was using a standard routine.
I have also taken the opportunity to add built-in support for generating null-terminated strings since it has emerged that some uses of DHCP Option Codes requires this type of string, for example PXE boot servers using DHCP Option Code 67.
The new 1.1 version can be downloaded free from http://jelockwood.blogspot.co.uk/2013/06/dhcp-server-on-os-x-server.html

Nice work John. Thanks for sharing this with the world.
I was pretty shocked when 10.6 server didn't include the facility to do this without going through this...
http://discussions.apple.com/thread.jspa?messageID=9027746
Your GUI looks to be a giant step forward.
Cheers,
Lyle

Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?

Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Setting up Cisco Aironet 1250 for home use

Hey everyone,
I'm rather new to the whole Enterprise Router lines. I've set up countless networks with Linksys routers in the past. However, this Aironet is giving me more trouble than I'd want it to. I was wondering if anyone could help. I've assigned it an IP Address and accessed that In-Browser interface and set up an SSID and activated the two extensions. I've been able to connect to the router with my computer and access the internet without restriction. However, when I attempt to connect a second PC or Laptop to the network, it won't allow network access to the second device. I've been stuck there forever. Is there any specific setup method I need to use to make sure more than one workstation/device? I want to use this router for home use, I often use laptops and move around the house a lot, so the advantage of better connection signal and speed is well worth it. Any help is highly apprieciated. If you need more information, don't hesitate to contact me.

Sorry for my late reply. Here is the config:
It wasn't connected to anything. This was a raw pull from a fresh cold boot.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 150 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 6406144
flashfs[0]: Bytes available: 25462784
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 54:75:d0:dd:b5:12
Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##################################################################################################################################################################################################################
File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01000000
Initializing flashfs...
flashfs[1]: 150 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 6406144
flashfs[1]: Bytes available: 25462784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio 1 A600 8000 0 0 A8030000 30
Radio 1 A600 8000 0 0 B8030000 13
tx_paks 1293
tx_paks 646
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-AP1252AG-A-K9    (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
Processor board ID FTX1423902R
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radio(s)
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 54:75:D0:DD:B5:12
Part Number                          : 73-10425-06
PCA Assembly Number                  : 800-27630-06
PCA Revision Number                  : B0
PCB Serial Number                    : FOC142025F4
Top Assembly Part Number             : 800-29039-03
Top Assembly Serial Number           : FTX1423902R
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1252AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.211: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.039: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.587: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:09.591: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
*Mar 1 00:00:09.591: %SNMP-5-COLDSTART: SNMP agent on host Cisco1250 is undergoing a cold start
*Mar 1 01:37:52.027: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 01:37:52.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 01:37:52.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 01:37:53.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 01:37:53.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 01:37:53.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 01:37:54.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 01:37:54.695: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 01:37:54.703: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.303: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5180 selected
*Mar 1 01:37:58.307: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 01:37:58.307: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.311: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 13 seconds
*Mar 1 01:37:59.307: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 01:38:00.307: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 01:38:02.931: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 01:38:11.919: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar 1 01:38:11.923: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 01:38:12.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Cisco1250>enable
Password:
Cisco1250#show running-config
Building configuration...
Current configuration : 1717 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Cisco1250
enable secret 5 $1$jDeQ$cFdx0aHAd8wj8tk6CCmXq/
no aaa new-model
dot11 ssid Home Network
   authentication open
   guest-mode
power inline negotiation prestandard source
username Cisco password 7 05280F1C2243
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 23D0220D02AE7FA723492AA01E34 transmit-key
encryption mode wep mandatory
ssid Home Network
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption key 1 size 128bit 7 0B4935657C801B3620154AB56630 transmit-key
encryption mode wep mandatory
ssid Home Network
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community Community RW
bridge 1 route ip
line con 0
line vty 0 4
login local
end
They way I connect it in the network is as follows:
BrightHouse Networks ISP Modem --> Cisco Aironet 1252 --> Incoming connections from computers and laptops.
Any ideas?

I cannot enter the key code for updating to QuickTime Pro 7 as there is no Icon in Preferences and no Registration option in menu?

I have followed the clear instructions to enter the purchased key code for QuickTime Pro 7. There are two options offered:-
1. Go into Preferences and select the QuickTime Player icon and enter the code that way.
2. Open QuickTime Player and open up ‘registration’ and enter the key code.
For whatever reason I have neither option available to me although QuickTime player is on my system and I use it regularly. It is version 10 build (118). I have run software updates and there is no upgrade available. I have downloaded the latest version and tried to load it but this fails because the system finds a version already available. I have attempted to uninstall but whilst it moves it from the Application folder, it remains on the Mac as it is part of the system files. So I cannot use the Pro version. The iMac is a 27” Intel about a year old and has all the software updates available to me installed.
Any offers for suggestions or past experiences that can help me overcome this conundrum?

Both answers were spot on. I made the mistake yesterday of downloading the version for Leopard in my haste. I also thought the issue was related to having to uninstall the current version X.
So the moral of the episode is check the version you have and make certain you download the correct version for your system. All works now.
Thanks chaps!

Can i have html code for date select options (SEARCH HELP)

Hi frinds,
I have a BSP Page with input as date.
Can i have html code for date select options (SEARCH HELP)
Moosa

Hi
Please find the sample code below.
FROM DATE
      <htmlb:inputField id        = "dd"
                        width     = "45%"
                        type      = "DATE"
                        showHelp = "X" <- Search help
                        alignment = "CENTER"
                        maxlength = "10"
                        disabled = "TRUE"
                        value     = "<%= w_FROMDATE %>" />
TO DATE
      <htmlb:inputField id        = "dd"
                        width     = "45%"
                        type      = "DATE"
                        showHelp = "X"
                        alignment = "CENTER"
                        maxlength = "10"
                        disabled = "TRUE"
value     = "<%= w_TODATE %>" />
Thanks
kalyan

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

DHCP Option 60: Go HERE.

Standard Match Code for Selection Options with Example

Hi Guys,
             Can anybody tell me Standard Match Code or Search help for Selection Options.
         ex: MBEW-MATNR , MBEW-BWKEY and MBEW-BWTAR. can anybody tell how to keep Search Help or Match Code for the Above Fields in ECC 6.0 with Example
          Very Urgent.
Thanks,
Gopi.

Well Gopi.. as per your requirement no need to use collective search help.
I guess you have three fields in selection-screen,out 3 fields you have two fields contains search help.
Create your user defined search help BWTAR ..
Check the below links for creation search help :
http://help.sap.com/saphelp_46c/helpdata/EN/cf/21ee2b446011d189700000e8322d00/frameset.htm
http://help.sap.com/saphelp_nw2004s/helpdata/en/41/f6b237fec48c67e10000009b38f8cf/content.htm
Hope you got it.
Thanks
Seshu

Sub-option code for a Cisco Aironet 1510 AP

Similar Messages

Maybe you are looking for