SUBSCRIBE and INVITE events with Asterisk 401 and 489 response.
Hello group, wondering if I could get your input on something quickly. We are using Asterisk with our SPA525 and SPA514 phones and looking through the capture logs it looks like Asterisk doesn't support the INVITE and SUBSCRIBE events. It typically comes back with a 401 Unauthorized or 489 Bad Event message. If Asterisk doesn't support these features can we prevent the phones from sending them? Your feedback is appreciated.
Ok, got some more data on this issue:
It hung again this afternoon. Would not ping, could not use the web interface, it just hosed. Syslog was running and the SPA112 spit out these two lines before it jumped off the cliff:
Wed Oct 24 15:47:16 2012 10.10.1.10 <29>Oct 24 15:47:16 SPA112 msgswitchd[1385]: MSGSWD RTCP Reqt len 12 Data 2,1092717788,2629110,0
Wed Oct 24 15:47:16 2012 10.10.1.10 <29>Oct 24 15:47:16 SPA112 msgswitchd[1385]: MSGSWD RTCP Reqt len 12 Data 2,2874904,7312,0
Those were its last words, so to speak. The asterisk logs were not helpful, just normal activity right up to where it was unreachable. Problem is I can't reboot this remotely when it gets in this condition. It requires a manual power cycle - this is not workable.
Cisco, you've been quiet - can you help here?
Similar Messages
-
My wife recieved invite event from my PC Outlook. She accepted it, but it never showed up on her iCloud or iCal on our iMac. Then I removed her as an invitee and it did not remove the event from her iPhone. So now she has a event on her iPhone that is not on either her iCloud or iCal. How do I remove it from her iPhone?
1) You asked "Does she need to reconnect to that itunes/computer and if so what do we need to do to remove this folder of pics from her ipod?" Yes, you have to connect the iPod to that computer and go to the Photos pane for the iPod in iTunes and uncheck sync photos and the click on synce/apply. In the future do not check sync photos.
iOS and iPod: Syncing photos using iTunes
2)
Create a NEW account for using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before.
Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card
Then on the iPod go to
- Settings>Messages>Send and receive and sign out your ID and sign into hers. Make sure that only her ID email address is listed.
- Settings>FaceTime sign out of your ID and sign into hers. Make sure that under You can be reached at only her ID email address is listed
- Settings>iCloud and sign out and sign in with hers
Contnue to use the commpn ID/account for Settings>iTunes and App stores. -
How to move Projects and Events with iPhoto video included in iMovie '11?
I work with a group of educators using iPads for video. One method for getting their clips into iMovie '11 is via iPhoto and then using the iPhoto Video link in iMovie to get the footage on a timeline (trying to import directly into iMovie '11, using the iPad as a "camera", has proved inconsistent, especially with footage from iStopMotion or Filmic Pro 1 and 2).
The problem is, when it comes time to copy or move an event and project, the iPhoto clips don't come along; they are dependent on the iPhoto library, so you can't continue editing on a different machine. I tried File > Consolidate Media, but it was inactive (in my test project, all clips came from iPhoto). If I look at Reveal in Browser, it goes to the bowels of the iPhoto library. If I copy the project to another drive, it too, points to the iPhoto library (if I'm on the same machine; otherwise it doesn't see it). I also tried optimizing the footage in the hope that it would create an Event with optimized clips that I could then transfer.
Am I missing something? It seems nuts that you can't transfer work to another machine without manually picking through the bowels of iPhoto. These days, lots of shooting is done on iPads and iPhones. Any help would be appreciated.My suggestion would be that in the future, they upload photos only to iphoto, and upload video clips directly to iMovie. In the early days of iOS, going through iPhoto was the only way, so it is a habit that I have had to break.
With iOS 5 and 6, iMovie now recognizes the iPhone and the iPad as cameras.
I agree that the Consolidate Media command should bring over iPHoto movies along with the photos. I suggest that you go to iMovie/Provide Feedback and let the developers know that you would like this feature. -
I made a movie in iMovie then deleted the clips in it. I have reimported the clips in an event with the same name as previously and some clips in the movie are still saying source slip missing even though they are there. Some clips are fine in the movie, but most are just black and when I hover over them, it says source clip missing. How to I fix this? Thank You
I did that too, then I did a migration assistant to a new Mac and ALL of my movies have Source Clip Missing now, even though the original clips are still in the iPhoto Videos. I can stand to re edit one or two projects, but not ALL.
-
Is it possible to enter events into a specific iCal calendar, then print a list of those events with the name and date on a single sheet? I don't need the calendar grid. I just want a list of events on a particular calendar, and their dates. Is that possible?
Not easily. Two possibilities:
1) If all the events have some common feature (eg you have included "XXX" in all the summaries), search for that feature then select and copy the found items at the bottom of the window. You can then paste them into TextEdit or a spreadsheet for printing
2) You could write an Applescript to locate the events and write them into a text file for printing.
The first one will probably give you what you want. -
How do you transfer photos to external backup and keep the photos in events with event name or with description name. Each time I have tried to transfer them they only transfer with a jpg number so you don't know what photos are what. When you have several thousand photos it is difficult to determined what is what.
Why does iPhoto have the ability to put photos in events and to give them descriptions if it doesn't transfer this info with the photo. I want to back my photos up to an external drive.The simplest way to achieve what you want is to back up the iPhoto Library. That will get everything.
You sem to be exporting from iPhoto to the Finder. The Finder does not have the same organisation capabilities as iPhoto. If you're going to do that you need to understand some of the differences between the two.
Event Name will become Folder Name.
'Description Name' I guess is the Title you give the Photo
Jpeg Number is the File Name assigned by your camera.
So: File -> Export
Set your Kind to Jpeg
Select your preferred Quality
Check the Boxes at 'Titles and Descriptions' and Location Information
Under FIlename select 'Use Title'
Click on Export. In the Next Window choose a New Folder as your export destination and then Name that as you prefer
Regards
TD -
Can I use AWT elements in a JSP, and so could I generate events with them?
This is because I�m doing a simple JSP that showing a button, my JSP is:
<html>
<%@ page import="java.awt.*" %>
<%! Button b = new Button("Hola!!!"); %>
<% add(b); %>
</html>
But when I tried to see the button in the browser, my JSP generates the following:
Compilation of '/RAID5/weblogic/myserver/classfiles/jsp_servlet/_gep/_alterno/_23_mayo/__mr4.java' failed:
/RAID5/weblogic/myserver/classfiles/jsp_servlet/_gep/_alterno/_23_mayo/__mr4.java:79: cannot resolve symbol
probably occurred due to an error in /gep/alterno/23_mayo/mr4.jsp line 7:
<% add(b); %>
Could somebody help me please?.....
Can I use AWT elements in a JSP, and so could I generate events with them?
Thanks!!!There are 2 ways to run a web page dynamically:
1) Reload the page via use of javascript or some other scripting language.
2) Use an applet to regularly check a URL for the data
Remember, as Paul pointed out, JSP's only generate HTML output. AWT components need to run inside a JVM not a just the browser.
I could recommend an applet but you may have problems with IE6 not supporting java. Otherwise there shouldn't be too much of a prob.
If you prefer to use an AWT/Swing setup (for example an application) rather than a JSP setup, Webstart is good for delivering online applications which operate standalone or remotely.
When you consider that the Java-Plugin and the Webstart puligin are about the same size it's just a matter of weighing up who your target clients are and whats easiest.
Cheers,
Anthony -
Within moments of subscribing I discovered interference with my REckon Elite Tax and Ledger software. I can no longer produce a PDF within the software and this is inpeding my work flow.
Hi elizabethc8523575,
Elizabeth Christodoulou wrote:
Within moments of subscribing I discovered interference with my REckon Elite Tax and Ledger software. I can no longer produce a PDF within the software and this is inpeding my work flow.
Please elaborate your issue. What kind of interference have you observed?
Regards,
Rahul -
Events with Scrpts and JavaScript in ADOBE forms
Hello All,
On an Adobe form I have field for sub totals. I am trying to choose 'Events with Scripts' on the SHOW pull down values and choose JavaScript in the language. I was able to do this some time ago but now, I am able to choose Events with Scripts but not being able to choose JavaScript for language.
I do not have much exp. with Adobe or JavaScript but I checked whatever I could think of but could not figure out. Any body ran into this issue before? Any ideas?
Please post and Thank you ...By trial and error, what I did is, chose 'Calculate' in the Show menu then chose JavaScript in the Language pull down menu. Then added my JavaScript code. Then went back and change 'Calculate' in the Show menu to Events with Scripts. Saved and executed it . It worked.
-
Error -200141 when doing buffered events with DAQmx and PCI-6602
When doing buffered events with DAQmx and PCI-6602 I get error 200141 - Data was overwritten before it could be read by the system.
This error is generated ONLY with random inputs >200/sec.
My setup is :
DAQmxCreateCIVCountEdges(taskhandle,"Dev1/ctr3"....
DAQmxCG+FGSampClkTiming(taskhandle,"/Dev1/FPI35",...
DAQmxSetCICountEgdesChan(taskhandlem,"", "/Dev1/80MHZTimeBase")
DAQmxSetChanAttribute(taskhandlw,",",DAQmx_CI_DataXferMech,DAQmx_Val_DMA,0);
Can somebody help ?i'm getting the same Error-200141, while reading semiperiods. (Meas_Buffered semiperiod continous)
while loop ex.rate seems to be pulsewidth*no.Samples to read. in my case PW=60ms
Input buffer size measured with Property node= 10000
why this error happens?? i cant use any mode other than implicit timing for semi-period measurement right??
more info: all the ai channels are used ~ 16 differencial.
i found one solution which is _ reinitializing the whole task if an error occur. is this the right way??
Kudos always welcome for helpful posts
Attachments:
Counter_1_Meas Buffered Semi-Period-Continuous_main_lv09.vi 34 KB
SemiPeriod_Reconnect Counter on Error.vi 35 KB -
My iCal used to default to one hour when I posted an event with a start time and no end time. The user guide says it will default to one hour. Since I started using OS Lion, my calendar doesn't do that. Can anyone suggest a way for me to get the calendar to default to one hour again? Thanks.
Dana,
Here are some iCal data entry tips from iCal Help:
Enter a name, date, and time duration for the event, and then press Return.
For example, you can enter “Super Bowl Party Feb 5,” “Movie with Rebecca on Friday at 7pm,” “Soccer Game on Saturday from 11am-1pm,” or “Breakfast with Jon,” and then press Return.
If you don’t enter a time duration for the event, iCal sets the event’s duration to 1 hour.
If you don’t enter any time information for the event, iCal makes the event an all-day event.
If you enter “breakfast” or “morning,” iCal sets the event to start at 9 a.m.
If you enter “lunch “ or “noon,” iCal sets the event to start at 12 p.m.
If you enter “dinner” or “night,” iCal sets the event to start at 8 p.m. -
IPhoto 11 and one event with 15,000+ photos - help
I am new to Mac, this is my first, but long time PC users (28 years)... so it is a learning curve. My photos were/are on an external hard drive, (due to last computer failure) and undamaged.
I only got my iMac 27 i5 on Friday, and have been importing them. The first time the programme ran - I probably foolishly imported a year's photos in one go (I have since realised the error after it froze).... and when I finally got out of the mess, I discovered I have one event with over 15,000 photographs in.
I have since been importing all my others folder by folder, as opposed to year by year - they go back to 1998.... so a lot in total.
My questions -
1 I have now discovered how to split the events, but it is so time consuming, with so many photos, is there by any chance an easier way.
and whilst I am posting perhaps someone knows how to get around this as well:
2 In Faces, I have gone through - so far - over 5,000 and written in names, but it isn't really very good at recognition, and I wonder whether it is worth carrying on with it - it shows only 2 pictures at a time, go to full screen and all it shows is around 8 - is there any way I can get a load up in one go of the 'same person' - or the computer thinks is the same, and do them in a batch
Thanks for any input, it is appreciated.
CarolI deleted the images of 15k+ and then set about sorting out the duplicates, triplicates and quadruplet folders it seems to have created.... took me ages, and I finally did that.
I had also purchased the Duplicate Annihilator as recommended in another similar thread, but that was going to take almost 4 days, hence I decided that I didn't have time for that to sort it out anyway, so I have done it myself this morning.
I was then asked to rebuild the database, so I set that going at just before 1300 (just over 2 hours ago), I came up from lunch and it was showing 97%.... and 80 mins it is still 97%
I am checking the activity monitor and it shows that it seems to be doing something, ie the nmber of threads stays at 26 but the %CPU keeps chaning, from 101.6 to 101.7 - so is it actually doing anything....iphoto has a black sectin with the circle thing going around in the centre....nothing else showing on the screen... actually watching it for the last minute or so and nothing is happening ... so is it working....
What should I do...
TBH I thought this would all be straightforward, and beginning to regret my choice of computer.... all I can say is it looks great, but isn't working as it should....
On top of that Time Machine has also now told me I need to start a new back-up but no idea where to find start a new back-up.... googling, and using spotlight hasn't brought up the answer yet
Still on 97%
Carol -
Can't create events with times between 10:01 and 19:59
I've recently updated to OSX 10.4.9, and now can't create events with times that start with a '1'. This only seems to be a problem on the day British Summer Time begins on 25 March.
I usually create my events in the month view, and input the start and end times by clicking in the time boxes and typing in the hours and minutes. However when I try to put in a start time of, say, 11:00, it puts in 21:00 instead. The only way around this seems to be to put in a time it will accept, like 09:00, and using the arrow keys to move it to the time I want. Or creating the events in the day view and clicking on the start time there.
Any ideas?Looks like you have found a wee bug. I can replicate it. You could report it though OS X Feedback or better though ADC, but for the latter you have to register first.
I usually create events by double-clicking in week view; often this gets the start time right, but if not then edit the start time in the info pane. Your bug is there with events created in day and week views too.
AK -
I'm locked out of my Blackberry again because it appears to be malfunctioning. When I type the password, it shows what I'm typing, instead of masking it with asterisks, and reverts to the alphabet unless I press Alt+ the key. Even when I carefully enter the correct password, it always says it's wrong. I have 2 or 3 tries left. Last time this happened a few months ago, it ended up wiping everything. I would like to avoid losing some valuable audio files that are stored only on the phone. Thanks!
Solved!
Go to Solution.I think you have a couple misconceptions about BlackBerry device passwords.
1. When you have entered the password incorrectly about five times, the ****** mask will show you the actual characters you are entering with the intent to help you see what you're entering.
2. Often users who have multiple numerals in their password will only press the ALT key for the first numeral and not those following, so for instance, if your password were "1234", you might have been pressing "Alt 1234" on the device, which makes the actual password to be "1ers".
Does that make sense? Does it sound familiar to your usage? So check the way you enter your password on the device... do you think you are entering multiple numbers but actually are not?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
I am a Creative Cloud subscriber and Acrobat XI Pro is asking for a serial number. When I enter my CC serial number, it indicates that the serial number is invalid
>enter my CC serial number
I don't know how that is possible, since Cloud accounts do not use a serial number... you download & install & activate Cloud programs with your Cloud log in to your paid account
Ask for serial number http://forums.adobe.com/thread/1234635 has a FAQ link
http://www.adobe.com/products/creativecloud/faq.html
http://helpx.adobe.com/creative-cloud/help/install-apps.html
http://forums.adobe.com/community/download_install_setup/creative_cloud_faq
what is http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html
Cloud Getting Started https://helpx.adobe.com/creative-cloud/topics/getting-started.html
-Install, update or UNinstall, and launch after installing
Maybe you are looking for
-
I got a new computer and don't know how to get music from ipod touch to itunes library
I recently got a new computer and don't know how to get music from my ipod touch to show on my itunes library.
-
Replacing Ampersand character - &
Hi All, I am working on the PO Layout for Oracle Applications. I have managed to get the program to show long text notes associated with the purchase order lines. However some notes include ampersand characters. I have no control over the generation
-
Lost my document icon on bottom of screen.
I lost the document icon on the bottom of my screen. How can I get it back?
-
Adding a watermark from App-Level script
Hello all, I've have a folder-level script that puts a button on the toolbar. This button calls a function that will insert watermarks and append several PDF documents to the current one. I've hit a roadblock with this.addWatermarkFromFile(). Whe
-
How to produce NameAlreadyBoundException using a client program?
Hi, I am trying to produce javax.naming.NameAlreadyBoundException using client program. I tried to add differnt objects for the same name repeatedly to produce it. But in vain. here is my code. what is the way to produce it in general. My actual aim