Substitution: optical drive to 3.5mm HD

Hi all,
Can I substitute the optical drive from a mid 2010 MacBok Pro to a 3.5mm Hard Disk, or it must be 2.5mm?
Thanks in advance,
Pedro.

Must be a notebook drive. There's no room for a full-sized disk drive. Notebook drives are 2.5" (not mm) and full-sized drives are 3.5" (not mm.)
Visit OWC to see their DataDoubler kit that lets you install another drive in the space used by the optical drive.

Similar Messages

2nd caddy replacing optical drive help

hi guys
i would like to know which type of caddy drive can be use to replace the optical disk in my macbook 5.1 aluminium unibody late 2008?
whats the connection type? sata?
how thick is the optical drive? 9.5mm? 12.7mm?
thanks in advance
erwin

You can probably just tape it down with package sealing tape. I would just re-use the old stuff. On my recent upgrade, my tape just barely had enough sticky left.
Edit:
Here is a source I found:
http://www.stewmac.com/shop/Electronics,pickups/Supplies:_Shielding/Conductive_CopperTape.html
Pretty cheap, too.
Message was edited by: Keith Barkley

Macbook mid 2007 optical drive replacment

Did anyone tried to replace an optical drive? Is it expensive?

The only limit on hard drives is height. It must be 9.5mm or less. The largest drive now available is a Samsung 1tb http://eshop.macsales.com/item/Samsung/HNM101MBB/ but it's only 5400rpm. There's a Seagate 7200rpm 1tb but it's 15mm high.
For 7200rpm drives the largest that will fit are 750gb http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&N=100007605%2060000334 0%20600030599&IsNodeId=1&name=750GB

2nd HDD caddy replacing optical drive for HP Pavilion 15-e073ca Notebook PC & Windows 10

Hello ! I am planning to add a SSD to my two-years-old HP Pavilion 15-e073ca Notebook PC. I found on some sites that I can remove the optical drive and put a second drive using a caddy adapter into the optical drive bay. I found that some people on the forum have done it successfully, but nothing about my PC model. I want to know if it could work with my product. In other words, there is my plan:1-Remove the actual HDD from the hard drive bay and replace it with the new SSD.2-Remove the optical drive and replace it with the caddy adapter containing my old HDD.3-Do a clean install of Windows 10 on the SSD, using a USB recovery flash drive made with my actual Windows 10 system (which was updated from Windows 8.1). I am planning to buy the following parts:1- a HDD / SSD caddy adapter for HP Pavilion 15 (model OBHD9-SATA-SATA-BU9), from NewmodeUS (http://www.newmodeus.com/shop/index.php?main_page=product_info&cPath=2_5&products_id=583)2- a 128 GB SSD drive (item SDSSDHP-128G), from SanDisk (http://www.sandisk.com/products/ssd/sata/ultra-plus/?capacity=128gb) I have some questions before buying the parts:1- Will the two drives (my old HDD and the new SSD) be recognized by the motherboard / BIOS and the operating system (Windows 10)? Is there a limit of one unique HDD/SSD drive on the computer?2- The height of the SSD is 7mm, and it seems that my old HDD is 9.5mm height (model WDC WD10JPVT-60A1YT0). Would it cause any problem (would I need to add spacers)?3- Do these parts work together and with my computer (size, compatibility)? Do you expect any problem with this upgrade?4- Will the clean install of Windows 10 work, since I plan to install it on a different drive than the one I used to create the USB recovery flash drive? I have never done a clean Windows installation before. Thanks in advance for your replies.Haghe

Hi:
Use the W7 32 bit drivers and software from the Probook 450 G2 except the graphics, firmware and BIOS files.
http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=6943827&swLangOid=8&swEnvOid=4053
Graphics:
First install the Intel chipset installation utility from the above model and reboot.
Second, install the Intel HD graphics driver and reboot.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=24246
Then install the nVidia graphics driver and reboot.
http://www.nvidia.com/download/driverResults.aspx/79892/en-us

How do I install Windows 8 on Mountain Lion (mac mini) 2010 Server using bootcamp with out Optical Drive?

I have a 2010 Mac Mini server running 10.8.4 (12E55). I just bought a brand new copy of Windows 8 from micrsoft. I have tried using boot camp and it will not recognize a burned DVD in my remote optical drive on my laptop running windows 7 or my macbook running Lion 10.7.5. I have had Microsoft on both of my computers remoted in for about 8 hours and they tried just about everything that I've tried.
Microsofts tech support has made me a bootable DVD and a bootable Flash Drive through remote desktop (awsome good job microsoft tech support). I have even tried formatting my mac mini's second 500GB hard drive to FAT32 using this whole disc as my windows partition. I know that when I go to install windows 8 it is going to reformat the drive to NTFS but all the articles that I've found, say this is what you have to do to get the drive formatted properly to get the ball rolling and get windows will fix it when it goes to install by reformatting to NTFS.
Ok so right now I have my second 500GB hdd on my mac mini formatted to FAT32 and I have tried to reboot holding my option key like I do on my mac book. If I want to boot to a different hdd on my macbook all I do is hold the OPTION key during start up and you get prompted to choose one of the bootable disc that is on your computer. Well if I put my USB drive which is bootable on my macbook into my macbook and do this right now its not showing up.
Now I just put the DVD that they made me in my macbook and it shows up as bootable disc. But the USB doesn't. (1 hour later) I just got microsft to remake the USB drive and am going to try that again so ta ta for now and I'll come back on to post to tell you if it works.

mikkel-kj wrote:
These apps paralells and fusion and virtualbox, are they in Mac App Store? And when I have the app installed what then, now it ain't only bootcamp what shall I do now to install windows 8?
Mikkel
Parallels, Fusion, and VirtualBox are available from their respective sites. Read their installation instructions which explain how to install Windows.

How do I install OSX onto a new SSD (in the place of my optical drive) without transferring all data across. However, with the applications, system and library on the SSD to improve the speed, but keep non essential items (the home folder) on the HDD

I have a mid 2009 13 inch unibody 2.53GHz MacBook Pro. I'm finding that it doesn't run as quickly as it used to.
A genius in the Apple store suggested that I replace my optical drive with an SSD, however only use the SSD for OSX, applications, system and library. Keep all documents, pictures, music etc on the current hard drive.
I would be grateful if someone could help me with:
1) installing OSX on the SSD without copying across data from the current hard drive
2) transferring applications, system and library folders across to the SSD so that they still function
3) changing my settings so that OSX reads the home folder from the current hard drive, as well as all the applications' data (documents, music etc...)
However, I would like to run iMovie, with all events etc solely from the SSD to speed up the process of editing movies.
If anyone could help with this, it would be much appreciated.

If you got the data transfer cable with your SSD, the procedure should be pretty simple - and there should be step-by-step instructions in the box. You're simply going to remove the bottom case of your computer (using a Phillips #00 screwdriver), take out the two screws in the bracket holding the hard drive into place (using same screwdriver), remove the drive and (use a Torx 6 screwdriver) remove the four screws that hold the hard drive in place. Then put in the SSD and reassemble the machine.
Then you'll plug up the old hard drive by using the SATA to USB cable and use the option key to boot from the old drive. I don't know what data transfer software Crucial provides, but I would recommend formatting the SSD using Disk Utility from your old drive ("Mac OS Extended (Journaled)" with a single GUID partition) and then use Carbon Copy Cloner to clone your old drive to your new SSD (see this user tip for cloning - https://discussions.apple.com/docs/DOC-4122). You needn't worry about getting an enclosure since you have the data transfer cable and you don't want to use your old hard drive.
There are a number of videos on YouTube that take you step-by-step through this procedure - many specific to Crucial SSDs and their data transfer kit - do a little searching there if you're unsure of how to procede.
Clinton

Optical drives reads but wont write after swap

hello everyone, I bought an iMac G3 450MHz that had had a 'superdrive' fitted. It both read and wrote CD's and DVDs. I tested it out and it worked just fine, I even made a back up copy of my Tiger DVD with it. I wanted to put the optical drive into my beloved Flower Power 600 iMac CD-RW so ,to make sure all the drive cables etc weren't disturbed, I just removed the whole caddy with the HDD plus the optical drive plus all the connecting cables, and popped it into my Flower Power. It booted up fine so I loaded (via carbon copy cloner) the contents of my original HDD. Now, when I look in system profiler, the optical drive shows up as a read/write but will only read discs. If I put in a blank disc the iMac's OS doesn't see the blank disc. Funnily enough my copy of Toast does see it and Toast launches itself. As I want to be able to burn disc images using Disk Utility this is a bit of a problem for me. I might just add, as it may be of some interest, that whoever fitted the superdrive had the HDD jumpers set to Slave but this was how it was when it worked perfectly in the 450MHz it came in so this was how I left them. The other little problem is the iMac won't sleep but I can live with that.

The reason your hard drive is set to slave is because it shares the IDE bus with the optical drive. With the stock optical drive, the optical drive is set to slave and the hard drive is set to master. However, that superdrive is probably hardwired to master, so the hard drive needs to be slave. As long as one drive is slave and the other drive is master, it should work fine.
Are you using the exact same system installation from the 450 on the 600? If not, there was probably some special driver installed to enable the all the superdrive features. Toast is a third-party app that is designed to work with many different optical drives, so such a driver would be built into the software, which would explain why it works (and Disk Utility does not).
What company sold (and installed) this superdrive?

DVD/CD optical drive is recognized only occasionally and temporarily

Hi, I recently bought an ASUS Essentio desktop model CG8350 running Windows 7 Home Premium 64-bit. My DVD/CD optical drive is not consistently being recognized. I've made few changes to the computer and have even tried reinstalling Windows (system recovery, factory settings), but no luck. The curious thing is that after booting up I can occasionally temporarily see the D:\ optical drive listed under My Computer or under Device Manager, but after a few seconds or about a minute after restarting or trying to read a disk, this disappears and the optical drive is no longer shown. I would take it back to Best Buy I bought it for repair, but unfortunately that was in the U.S. and I've since moved to Canada. It's frustrating that Best Buy Canada won't honor service warranties for items bought from Best Buy U.S. If there's something I can try in order to avoid shipping it off to ASUS or back to Best Buy U.S. (at my expense, and potential loss of PC for a few weeks), I would much prefer that. These are the things I have tried so far: 1) opening it up and checking/re-plugging the power cable to the optical drive and the data cable between the optical drive and motherboard. All cables seemed fine. The drive ejects and spins a little bit when a disk is inserted, but neither a blank CD/DVD nor a commercial CD are recognised after insertion. 2) looking at the registry to try the "delete UpperFilters" and "delete LowerFilters" trick that I've seen posted several times. Since the computer had Windows 7 from the start (was not upgraded), these entries were not visible under the suggested registry subkey. 3) under boot options, I've selected "Disable Driver Signature Enforcement" and have booted up. The optical drive showed up under My Computer and/or Device Manager for a few seconds or a minute, but then vanished. 4) disabled integrity checks: I've pasted "bcdedit /set loadoptions DDISABLE_INTEGRITY_CHECKS" into the Run window. After restarting, the optical drive is again occasionally visible, but only for a short period after which it disappears. 5) following a tip on one website, I tried shutting off and unplugging the data cable between optical drive & motherboard, restarting the computer so Windows could "see" there was actually no optical drive connected, then shutting off and connecting the data cable again and restarting. no luck. 6) I've run the Microsoft Support Fixit executable under "Your CD or DVD drive can't read or write media". The first time I ran this, it ran for about 5-10 minutes, but didn't diagnose a problem. The second time I tried to run it (after the Windows 7 re-install), is said my CD/DVD drive was not detected, so didn't run. 7) I've tried built-in Windows diagnostics and ASUS diagnostics, but they didn't help much. 8) I've updated ny BIOS to the most recent version. I've now run out of ideas and can't find any other suggestions on previous troubleshooting searches. The observation of the drive occasionally being seen for a few seconds/minute after start-up before disappearing seems like it might be a good clue, but I'm not sure how to interpret this. I did get it to play an audio CD a couple hours ago, but after trying to use my drive for something else after that, it's right back into the situation of not being consistently recognized, except sometimes immediately after booting up and then only for a short period. Any help or suggestions you have will be very very welcome -- thank you.

Honestly since it was recalled due to the sandy bridge recall anyways, it is going to have to go to asus eventually so I would just have them fix both in one shot. The Canada and U.S. support number is the same and I'm sure they could fix both issues at once to save you time: 1-866-625-9873
Crystal
Superuser
Forum Guidelines | Terms & Conditions | Community Guidelines | What is a Superuser?
*Remember to mark your questions solved and click the star to give kudos to show your thanks!*
While I used to be a Best Buy Employee, I no longer have any affiliation with Best Buy.
My opinions do not in any way shape or form represent Best Buy's Official decisions.

New MAC Mini w/OSX Lion - will not boot from USB or external optical drive when attempting to use BootCamp to install Windows 7?

The University recently purchased 6 brand new MAC minis for deployment in classrooms I support. I am attempting to create a dualk--boot environment comparable to our existing computer systems, only these machines wil be running MAC OS X Lion and Windows 7. After following the procedures outlined in the BootCamp on-screen prompts, and attempting a few techniques I found in the tech support user-base, I am still unable to get the MAC mini to boot up from the USB flash drive, or from an external optical drive, so that I can complete the installation of Windows 7. When using the Boot option key at start-up, all devices are displayed suggesting that they are being properly recognized, however the computer boots to a black screen with an error message indicating that "No bootable devices are found - press any key to continue." I am able to boot into the computer's internal drive, but not from any external devices. I fully expected that the semi-automated BootCamp procedure properly prepares the USB device for booting, and for installing the Windows 7 OS.

Meh, with the price they take for a drive in Denmark, I don't think it's worth it... They take around 160 $ for the drive (that's the cheapest MacBook drive I could find), and I am not even sure that's the one I need.

How to install windows 8 using bootcamp with no optical drive

Hi,
I have a mac book pro 17" late 2011 with Mountain Lion installed.
I have previously installed a windows 7 using bootcamp without an optical drive by creating an install disk as part of boot camp option.
I still don't have an optical drive.
The other day I removed my Windows 7 since I want to try Windows 8 but when I try using boot camp to install windows 8 it is asking for an optical drive and the option to create an install disk is not available anymore.
Any idea on this issue?
Thanks much

Windows 8: enable Hyper-V, it really helps.
http://www.gizmodo.com.au/2012/03/windows-8-on-a-macbook-air-beautiful-and-kinda -broken/
http://www.windows-now.com/blogs/robert/hyper-v-3-0-confirmed-for-windows-8-clie nt.aspx
http://www.windows8update.com/2011/12/06/enabling-hyper-v-in-windows-8/
http://huguesval.com/blog/2012/02/installing-windows-7-on-a-mac-without-superdri ve-with-virtualbox/
Disable Windows 8’s Adaptive Brightness to Fix Dark Screen Problems
http://www.howtogeek.com/107173/disable-windows-8s-adaptive-brightness-to-fix-da rk-screen-problems/
It should be straight forward and no different, except you are burning an ISO and that always needs to be done at slowest burn speed for any version of Windows.Otherwise it won't work (even if it manages to install it will fail on restart or some other point).
Windows 8 Release Preview
http://msdn.microsoft.com/en-us/windows/apps/default
https://blogs.msdn.com/b/b8/?Redirected=true

Do I really need an optical drive (external) for my MacBook Air to install Win 7 with Bootcamp?

I have a Macbook Air (11" if it matters, the tiny one) that was purchased late last year, new. I would like to install Bootcamp and be able to boot into Windows 7, 64 bit. I have a Windows 7 Professional disk, which I would have to find an optical drive of some sort to install. The Boot Camp PDF guide doesn't mention the use of any kind of USB bootable install. In fact, I often see (on Apple support pages) that an external optical drive is required for Macbook Airs.
Is this the case? If not, does anyone have any advice on how to make sure this goes smoothly? I'm a bit of a newbie to Macs. Thanks.
(Note: I didn't select my OSX operating system, but it's been updated regularly.)

Thank you Rysz, but (if you scroll up & read my original post you will discover) I don't own my new MacBook Pro...yet! I'm just researching ahead of time to help me make the decision. The customized MBP I have saved in my cart is over $3000 (incl the 3-yr support plan). So it's going to take me a little bit of research before I decide or before I can really justify the purchase.
I just wanted to be prepared for all the inevitable technical / learning-curve headaches that I will experience IF I take the plunge.   And as everyone has experienced, when you're new to and making your first purchase of a different technology, and you don't know what to expect about a purchase, you ultimately get it home, set it up and find it didn't come with all the necessary interface devices, converters or cables, etc. And of course the online purchase procedure wizard doesn't tell you or ask you what else you will need if you want to perform a specific task.
But I'm sure (if) once I do make the purchase, I will definitely be back here to pick everyone's brains! These communities are fantastic.   Thanks again!

I have a mid 2010 Macbook Pro, How can I install Windows 7 without an Optical Drive?

For clarity: I have a mid 2010, Macbook Pro. I recently decided to upgrade to a Crucial SSD drive, double the ram (8 gigs), and remove the optical drive in favor of using my old drive as a back up. I am also currently running Yosemite.
I want to install Windows 7 onto my SSD, using bootcamp. Unfortunately I no longer have an optical drive installed, which makes things difficult as Bootcamp does not even give me the option to create a bootable USB.
Now, this is where things get kinda fuzzy:
MId 2010 macbooks use EFI, and are quite capable of booting from USB. How do I know? Because I booted from a USB drive in order to do a fresh install of Yosemite on my SSD.
I have read mutliple forums and threads with claims that folks have had no problems doing this on 2008 Macbook Pros running Snow Leopard. However, what seemed to be required was some clever .plist modding. I have used both text wrangler, and x-code to do this, unfortunately upon booting of bootcamp, bootcamp instantly crashes. Naturally, I can restore bootcamp because I made backups of the .plist file.
It would seem that modffying the .plist file assumes that the option to create a bootable USB device is grayed out. In my case, it is non existent.
I have also read that folks have had success using rEFIt, however rEFIt has been forked to rEFIned, and the developer of rEFIned made mention on his site that Yosemite handles booting differently than previous versions of OSX.
WIth that, I was hoping that some kind person could explain to me whats going on, what I am missing, and what I can do to make this happen just shy of tearing down my MBP and reisntalling the Optical Drive and dusting off my Win 7 disc.
Also, my Model Number/Bootrom is MBP 6,2.
Thanks in advance!

Thank you for your reply, and the information. This is what I came up with:
I added the strings as instructed, however when I went to sign the script in terminal, I was told:
/Applications/Utilities/Boot Camp Assistant.app: replacing existing signature
/Applications/Utilities/Boot Camp Assistant.app: code object is not signed at all
In subcomponent: /Applications/Utilities/Boot Camp Assistant.app/Contents/info.plist
Also, here are screen captures of the lines that I added. Mine are the top string entries:
Thank you for your help, thus far!

How do I install Windows on a new Mac Mini (w/o optical drive?)

The new Mac Mini does not have an optical drive and I would like to install Windows with Parallels Desktop 6
Any ideas? Can I put the iso on a USB drive or mount a NAS?
Thanks for ay help!
Enzo

You can burn an ISO of a bootable disc back to a DVD, but not to a USB device. I don't know if Parallels is able to install from an ISO, but it may install from an external drive. This is why you should read the documentation for Parallels or ask at their tech support site.

How do I install windows 7 on a macbook pro mid 2009 using bootcamp and no optical drive?

How do I install windows 7 on a macbook pro mid 2009 using bootcamp and no optical drive?
My optical drive is non-functional and I want to dual boot with win7. The only problem is my macbook does not boot from USB at all, even when I hold th ALT key down when it is starting up.
-I have a flashdrive with win7 on it.
-I mounted the ISO of win7 with toast for bootcamp to do its thing.

Good luck.
Consider this a bump so that hopefully someone with better news spots your thread.
Allan

How can I install Windows 7 on a Retina MBP with no optical drive?

I'd like to install Windows 7 on a Retina MacBook Pro via Boot Camp.
However, the only distribution of Windows I'm aware of is on a physical disk.
My MBP doesn't have an optical drive. It can't read disks like that.
I'm hoping there's some kind of workaround here, because I'd hate to spend money on an external optical drive I'm only going to use once.
Does Microsoft offer a way to buy Windows 7 via a download?
If so, can I then copy the downloaded installer that onto an external USB hard drive and install from there?
Or is the only option to buy an external optical drive? (If that's the case, any guidance on which one to buy -- can I get away with a generic one or do I need to shell out $80 for Apple's "Superdrive?")
I actually have another Mac that does have an optical drive. Could that help me out somehow?
Any help would be greatly appreciated.
Thanks!

You can follow the instructions here to copy your installation disc over to a USB jump drive: http://lifehacker.com/5347382/wintoflash-turns-your-windows-installation-dvd-int o-a-usb+based-installer

Substitution: optical drive to 3.5mm HD

Similar Messages

Maybe you are looking for