Successful DSL Setup With Westell 6100G and Linksys WRT54G Router

After a week of searching I finally figured out how to get DSL setup with my Linksys router.
All I could get out of the Westell > Linksys router configuration was DSL downloads limited to less than 0.2 Mbps.   No matter what I did on the router settings that was it.    I had a second eHome router that easily configured and achieved the 1.0 Mbps download speeds so that confirmed Verizon and the Westell modem were not the issue.
So what's wrong with the Linksys router configuration?    I had the Linksys WRT54G router Version 5.   Checking the firmware it was the original release of 1.0.0.   (See your routers instructions which can be downloaded from Linksys for how to check your firmware).   I downloaded the latest firmware version for this router model and version number.    Following the Linksys instructions I flashed the latest firmware 1.02.8.   Now I had an updated modem ready to be configured for DSL.
Assuming you already followed Verizons instructions to set the Westell modem to bridge mode setup your router to work with it.
Step 1: Go into the modem typing its address... Default 192.168.1.1   leave the ID blank and the default password is admin.
Step 2: Go to the Basic > Setup screen.
Step 3: Select PPPoE and the screen menus will change
Step 4: Enter your Verizon ID (exclude @Verizon.net)
Step 5: Enter your Verizon Password.
Step 6: Go to the bottom of the screen and hit Save.   Wait and the router will indicate it was saved.
That's it.  All you need are the three entries above to get it working. Turn off the PC, Router and Westell.   Turn on the Westell, then the router and then boot the PC.   It should work at this point.    I now get the full DSL speed for both downloads and uploads.
The bottom line....check you router, especially the older models for updated firmware before you give up on it.

Glad top see you found a configuration for your Westell and Linksys to function. Thanks for posting resolution.
Mike_VZ
Verizon Support
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms of Service, or your Customer Agreement Terms and Conditions or Plan.

Similar Messages

Bellsouth and Linksys WRT54G Router

Hey,
I am able to connect to the internet through my modem and can connect to my router from my computer but when I hook the modem up to the router I am unable to get to the internet. I have done all the steps from Linksys and still no results. Does anyone know the exact settings that the router needs in order to get it to work?i.e Do I need a domain name or anything like that? Any help is apprecitated.
Thanks

There are a few settings you need to understand about having the router connect to Internet through the DSL modem. The router has to first establish connectivity with your DSL service by logging on. This is accomplished via the following settings.
1. Login Type should be set to: PPPoE
2. The username/password for your DSL service, must be entered into the router. This is the same uname/pwd that you use when you connect the PC to Internet thru the DSL modem. It should be something like (xxxxxxx)@bellsouth.net for username and then the password.
3. With Bellsouth there is no need for Host name or Domain name. You can give the router a unique name per your preference.
And finally, In order for your PC to now communicate with Internet via the router, You must setup the router as the DHCP server.
4. Set the router for DHCP server (enable). The router will become the defacto IP address provider on your network and will isolate you from the direct connection that the DSL modem normally provided.
With these settings your router should log into your DSL service thru the modem and you should be up and running.

I have one PC with a modem and linksys router #BEFW11S4 i...

I have one PC with a modem and linksys router #BEFW11S4 installed. I have 3 other PC's which connect to it via Linksys wireless-G adapters. Things have been working just fine until recently when now at least twice a day my Pc's with the adapters lose connection with the router. Any suggestions?

Open routers set up page ..... click status & see the firmware version ...... if required update ....download the latest firmware from http://www.linksys.com/download ........

Issues with Deskjet 5650 and Linksys wireless print server.

I have a iMac DP 1.8, a iMac G3 700 mhz running Tiger and a Toshiba laptop running XP and I am on a wireless network. I use a Linksys WRT54G router for the wireless and I am using a Linksys WPS54G wireless printserver to connect an HP Deskjet 5650 to the network. This was all working fine for the past 2 months until Monday evening when the Mac's lost connection to the printer. However the Toshiba can print to it just fine.
I cannot for the life of me figure out what happened. The iMac DP recently had a security update for intel installed this past Monday, but no updates have been installed on the G3 iMac. I have contacted Apple, HP and Linksys and they have been no help at all. Apple says it's a Linksys issue, Linksys says it's Apple issue and HP is just cluless. I would appreciate any assistance offered.
Thanks
iMac DP 1.8, iMac G3 700mhz Mac OS X (10.4.5) Linksys wireless router WRT54G, Linksys wireless printeserver WPS54G

Paul, I am amazed you were ever able to print via the Linksys wireless server on your mac. I have the identical router and print server, and only the Windows PC's on my wireless network have been able to share the printer on that wireless server. I've been unable to find a driver for my iMac, and could never get the iMac to find the server. Finally gave up and bought an HP 2600n color laser and connected it directly to the iMac via USB. You're right about lack of help from Linksys. There is an Apple folder under "unsupported" on the print server installation CD, but there's nothing helpful in there.
iMac (Intel) Mac OS X (10.4.5)
iMac (Intel) Mac OS X (10.4.5)

Having trouble setting up a linksys WRT54GS router with v...

Having trouble setting up a linksys WRT54GS router with verizon DSL using a westell 6100F modem. the modem works fine by its self but the router will not connect to the internet when installed like the cd tells you to.
online help and phone help has been less than helpful, anyone have any Ideas?

Ok I found " Installing the liksys wireless router with a westell 6100 modem" in the verizon troubleshooting guides. printed the instructions so I would'nt forget. step 1 open your web browser and enter http://192.168.1.1 in the address field. PROBLEM it comes up with a login screen that I don't know how to sign into. tried the obvious stuff. cannot get past the login screen. I knew this sounded to easy to be true. anyone have any ideas?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

Linksys WRT54G router--Why doesn't it work with my Macbook?

I have a perfectly functional Apple MacBook (Unibody, late 2008) running Leopard 10.5.6. I have used it to connect to public Wi-Fi but it is unable to connect to my home Linksys WRT54G router. I called Apple Tech Support, and they suggested that I change the wireless channel and/or temporarily remove the WPA encryption. I did both, the computer still could not connect. In System Preferences on the MacBook, it tells me that "AirPort does not have an IP address and cannot connect to the internet." The tech support guy tried to help, but in the end basically told me that the router just plain might not be compatible with Apple products. (My iPod Touch cannot connect either.)
I can buy a new router, but this one works perfectly for the rest of the computers in the house (PCs) and they're expensive--and there's no guarantee that those will work either.
So: Does anyone know any solutions short of buying a new router that would make my Linksys compatible with my Macbook AND our home PCs? Or, failing that, a good, WPA-encrypted router that WILL work with both?
I have a Snow Leopard disk (I just received the computer on Thursday). Would upgrading to Snow Leopard be of any help? I'm planning on doing it anyway one of these days.
Many thanks in advance,
Sola Gratia

You are in the wrong forum but I'll try and help anyway. That model of Linksys router has a long history of not getting along with Apple products. That is not to say it will never work, but it does require that you download and install the latest firmware for the exact model of router that you have. There are multiple sub-models of that router so make sure that you get the right one.
Once you have done the firmware update, restart your router and try it again. WPA-psk should work but for troubleshooting purposes, turn off encryption and see if you can get your MacBook and touch working. You might want to use WPA2-psk instead of WPA.
I would hold off on Snow Leopard until you get WiFi working. Nothing like changing to too many things at one time to really mess things up.

PS3 and linksys WRT54G. found a fix!!! please look

http://vibrantreality.wordpress.com/2007/10/27/ps3-and-linksys-wrt54g-the-solution/ not sure if it has been posted but it works!!! enjoy

Let me review my setup. I have a WRT54g Version2 Linksys Router. The Router firmware has been updated. I have two computers wired to the router and they work fine. I have a Linksys Media Center and a Laptop that work in a wireless environment and they work fine. The ISP is Comcast.
The PS3 is wired through a Linksys switch to the same Router. The switch is a Linksys Etherfast 10/100 8-Port Workgroup Switch EZXS88W ver 3.1. On the PS3 I have tried all the combinations of DNS that I can identify. The setting for MTU is at 1492 which matches the status shown on the Router screen. I have tried UpNp in both the Disabled and Enabled modes. I am currently using the DNS's that appear on the Status page of the Router.
On the Router I have set the IP address for the PS3 up as a static address in the DMZ as 192.168.1.2 UpNp is currently disabled. I have assigned ports to the static IP in the Gaming screen and enabled them..I have entered the DNS's numbers from the Status page on the Setup page for the Router as static IP DNS's.
If I connect the Laptop to the same wire that the PS3 is currently connected to, the laptop comes up fine on the Internet. The PS3 finds the IP address but continually gives me the DNS failed (80710102) error message. This is also true if I run the PS3 in a wireless environment.
Your assistance is greaty appreciated.

Airport Express and Linksys WRT54g

I can't get my AE to find my Linksys WRT54g router. How can I make this work together
Thanks
Pete

Follow the detailed instructions posted in this discussion by David Lovell:
David Lovell, "Airtunes for XP with a Wired/Wireless network" #1, 09:05pm Jan 8, 2005 CDT

Help! Extremely slow Internet speed using Linksys WRT54G router

I have an eMac running OS 10.3.9 and wired to a Linksys WRT54G router using ethernet cable. I have to use this router for my work PC. I'm also using WildBlue satellite internet. The problem is, I'm getting about 1.5 Mbps on my PC, but less than 33 Kbps on my eMac. It was running faster before using dial-up. I've called WildBlue and Linksys tech support, and they can't help. Can anyone help?
By the way, my son is using his iBook on the same router, only wireless, and he's happy with the speed he's getting compared to dial-up.
Thanks,
Eric

1400 kbps is a lot nicer than 33 kbps, isn't it? You can possiblly tweak it a little more --- I know I've seen a MTU of 1460 mentioned --- since you can also revert back to the 1400 MTU setting you found.
(Broadband Optimizer is in one sense a nice GUI to the terminal commnads you found and used.)
One more thing to be aware of, satellite internet is subject to longer latency times than cable or DSL, due to the unavoidable geometry of bouncing data packets off a satellite in orbit. That could be an issue if you ever want to play real-time online multiplayer adventure type games. It shouldn't be an issue for being able to grab OS updates in minutes instead of hours, through. Enjoy your broadband access!

Why does the Linksys WRT54G router REQUIRE a hostname when it's never used?

Why does the Linksys WRT54G REQUIRE a hostname when it's never used?
I can't find a single use for the router hostname, yet the Linksys WRT54G version 5 firmware v1.00.6 wireless router REQUIRES a hostname, even though nothing actually uses that hostname.
Why does the router require a hostname (why can't we just leave that field blank)?

Date: Sun, 8 Jul 2007
To: [email protected]
From: "Debbie Hurley"
Subject: "Unnecessary Router Name Requirement" bug in WRT54G V5
This is to report a bug in the "Setup", "Basic Setup"
tab, "Router Name" field
(https://10.2.18.20/basic.htm) in the otherwise
wonderful Linksys WRT54G V5 wireless router (firmware
revision 1.02.0).
As you are aware, a router is a security and privacy
device; as such, it should not require identifying
information if that identifying information is not
needed nor used by the user or their ISP.
Such is the case with the "router name" field.
In the case of the "Unnecessary Router Name
Requirement" bug, I am reporting to you (and to the
associated Linksys forums at forums.linksys.com) the
Router Name field should NOT be required. It should be
an option to leave the Router Name field blank.
The fact that the router name field MUST exist
(whether or not it is actually used or desired), is an
obvious security and privacy flaw in the otherwise
wonderful Linksys WRT54G router. Please fix this bug.
Thank you very much,
D. Hurley
(Mod note: Post has been edited for non-compliance of forum guidelines.)
Message Edited by primus on 07-08-2007 11:13 PM
Message Edited by primus on 07-08-2007 11:14 PM

AirPort Express drop-out / skips -- Windows XPSP2 w/ Linksys WRT54GS router

Hello,
I'm having some skipping / drop-out issues when streaming music from a Windows XPSP2 fileserver, which runs iTunes 7.3.2.6, to my AirPort Express. I've long suspected my LinkSys WRT54GS router. Here are some things I've tried:
* tried enabling logging on my AirPort Express unit, (I actually installed a Windows SysLog client and ensured it was working) but it reveals no useful information after a skip -- just debug logging. No change.
* changed the wireless channel from 6 to 11. No change.
* Do not have wireless security enabled (just don't broadcast ESS ID). No change.
* Latest firmware on router, AirPort Express, and iTunes. No change.
* All other wireless devices in the house turned off. No change.
I'm seriously considering buying a new wireless DSL router to see if it makes the problem go away (any suggestions to makes or models appreciated). Unfortunately my WRT54GS is not one of the routers that supports reflashing with a third-party firmware, or I would have done this eons ago.
Another thing I am not sure how to test is the signal strength that the Airport Express gets from my LinkSys WRT54GS router. I've not been able to figure out how to get this information, and I also do not know what are considered good / not-good strengths. Any help here would be great.
Here are some details.
AirPort Express with Firmware 6.3, communicating wirelessly over Channel 11 to my LinkSys WRT54GS router with firmware 1.52.0, into which my Windows XPSP2 fileserver is physically connected with CAT5 cable. The music files are served up on a Maxtor DiamondMax 10 7200 rpm 300GB Serial ATA-150 Hard Drive.
I've really tried everything I can think of, and I still get skipping.
Specifically, music will play fine for 45 minutes, or 5 minutes, or an hour; then, the music will suddenly stop. The AirPort Express will continue to have its green LED on, though. The music will resume 1-10 seconds later. This skipping will happen periodically for a 1-2 minute period, usually 2-3 times per minute, go away for an indeterminate amount of time; or, it might persist until I get tired and turn off my stereo. There is no pattern as to time of day so I don't suspect neighborly interference.
Other things in the house are an older 802.11b laptop, 5.8GHz phone, brand new microwave, and a few dozen Palm and Windows PDAs that all have their WiFis disabled, where appropriate.
Any suggestions or ideas would be fantastic. This has been a problem for a couple of years now which I have systematically (though unsuccessfully) tried to solve.
Thanks,
-Jeff

I haven't yet budgeted to buy a different router, but I'll respond when I do as to whether this was the fix or not.
Just an observation ... in your case, the music streams wirelessly from your laptop to your router, and then wirelessly again from the router to your Airport. That's 2 wireless paths it must go. In my case, music streams directly to my router with a LAN cable; then, wirelessly from my router to the airport. So that's only 1 wireless path, and even still I am experiencing problems.

Having trouble with multiple wireless users on WRT54G router

Basically, there are 3 of us wirelessly sharing the internet via a linksys WRT54G router. I have our router password-protected, to avoid randoms stealing out broadband. I am a Mac user (3 year old computer), the other 2 are on PC laptops.
At the moment, I have an excellent internet connection, and it's working just fine. However, if my room mate connects with their laptop (a fairly new model), my internet connection stops working. I still have a signal, but it just really slows down/often stops working entirely. It's as if their wireless connection takes priority and ignores mine (essentially nullifying the router's purpose).
Has anyone come across a problem like this before? Your assistance would be super helpful and appreciated.

Hi, perhaps you may try the following steps to improve the performance of your router:
• Upgrade the router’s firmware
• Reset the router after the firmware upgrade
• Optimize the router’s wireless settings
• Use a wifi analyzer like http://www.metageek.net/products/inssider/ to set a non overlapping channel to the router
• Relocate the router on a more central location for better wireless coverage
• Avoid placing the router on a glass or metallic surface

Cant connect IPOD to linksys WRT54G router

Hi, i have a LINKSYS WRT54G router .. i bought an apple ipod touch recently and i am unable to connect it to my wifi network. My ipod detects the wifi network but when i select it , it asks for password. now i dont know which password is this bcoz everytime i poer on my computer or laptop i never type a password b4 accessing internet.. it is auto connected. i know the admin password for my router but that is denied by ipod to connect to internet. Is there any other password we have to give for connecting deveices through LINKSYS or some changes i need to do in my connection ? PLzz help plzzzzzzzzzzzzz

you can go to this link for instructions on how to get your wireless password:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3698

Time Capsule: Port Forwarding Issue and DHCP with Westell 6100g Modem

Ok two issues as of right now, but more down the road i think... Anyways, number one, i would like to be able to backup my computer using time machine and my time capsule.. Right now it works properly when inside the local network, was wondering if there was a way to backup when outside the network... i travel a lot and always have my macbook pro with me.. Also, i have a USB hard drive connected to the usb port on back of time capsule but its not showing up anywhere... is that only for printers??? that's not such a big deal, but would be nice to have access to that hard drive from multiple computers... OK so part two of my issues is, i have a WESTELL 6100g modem for DSL verizon service, which is crappy, but that's besides the point, it is a modem/router, so i have the time capsule connected directly to that westell.. the westell only has one Ethernet port, so that's wired to time capsule and then my computers are connected wirelessly and wired through the capsule. It seems that the westell is distributing the IP's and is controlling the port forwarding and what not.. I have tried a few things to give control to the time capsule but that didnt work.. i followed these directions on the web page http://www.dslreports.com/faq/vz/4._Hardware#13600 but it didnt work properly, i couldn't log onto the web at all.. Maybe im doing something wrong.... Anyways, what i really want to do is control everything that the westell is controlling right now with the time capsule... i want to give out IP's and also control port forwarding with the capsule.. Any way of getting that accomplished would be AWESOME... I'm somewhat intelligent when it comes to computers so i should understand everything you are talking about... please help!!!

wattabing wrote:
Ok two issues as of right now, but more down the road i think... Anyways, number one, i would like to be able to backup my computer using time machine and my time capsule.. Right now it works properly when inside the local network, was wondering if there was a way to backup when outside the network... i travel a lot and always have my macbook pro with me.
If you have Back to my Mac (available online service from Apple's MobileMe), then you can perform the following actions with your Time Capsule remotely,
1. Remote disk access to both the Time Capsule disk and a compatible disk connected via the Time Capsule's USB ports.
2. Remote configuration.
Also, i have a USB hard drive connected to the usb port on back of time capsule but its not showing up anywhere... is that only for printers???
Printer, hub, or compatible disk.
http://support.apple.com/kb/HT2421
Anyway, it could be a setup issue for you, assuming you have Back to my Mac (MobileMe) then the procedure for Time Capsule services is shown in the following Apple support kb
http://support.apple.com/kb/HT3486
and for USB disk please see the following Apple support kb
http://support.apple.com/kb/ht2426

Successful DSL Setup With Westell 6100G and Linksys WRT54G Router

Similar Messages

Maybe you are looking for