Suitable marker break point error for dual layer DVD!

I'm a new FCP user of a few months and DVDSP of one week.
I have read the manual again and again and I am still not sure how to add a suitable break point. I added a chapter marker and set it as a dual layer break point, not sure if that is correct. Quicktime Movie is 5.9 GB, it does everything except burn to DVD in SP. I can burn this movie in IDVD though. Please help me!
Thank you in advance for your help, I appreciate the assistance everyone so willingly gives. Thank you!

Will compressor or Mpeg cause degeneration of picture quality?
If you put it on DVD-Video, you have to convert it to MPEG2 (with either Compressor or by letting DVDSP convert it). It will lose quality as a result. The only way to minimize this is to use as high a bitrate for your MPEG2 file as possible. Compressor has some presets labeled 60 min, 90 min, and 120 min, that will allow movies of that length to fit onto a single-layer DVD.
You should probably re-read the opening chapters of the DVDSP manual; they cover this important and fundamental information relatively well.

Similar Messages

Media write error for dual layer DVD burn

I am having a problem burning a dmg to a dual layer DVD using the internal DVD writer. I have tried both Disk Utility and SimplyBurns.
Both program s go through the preparation for the file, and when it attempts to burn the disk I get a 'media write error'. I am using Memorex DVD +R DL disks. I have successfully burned both CDs and regular DVDs with the drive.
Does anyone have a suggestion on how I can fix this?
Thanks

I am using Memorex DVD +R DL disks.
Try Verbatim DVD+R DL discs.

Project for dual layer DVD

Hi there,
I have a project which contains several individual sequences that have been compressed separately and which constitutes several parts of my future DVD.
The total size is such that I need to burn a dual layer DVD.
How do I determine where to include the marker indicating to switch layer ?
I have done it before with a long project containing only one sequence, but this time the sequences are independent....
Would DVDSP include automatically a "change layer" marker if I burn as is ?
Thanks in advance
Ivan

I'd recommmend looking up "About Choosing a Dual-Layer Break Point" in the DVD Studio Pro user's manual or Help File.
-DH

Keeps asking for Dual layer DVD

I made a slideshow in iMovie and shared to iDVD8. The media windows shows the file as 2.7 gig. But when I go to burn it says to insert a Dual Layer DVD because the project to large.
I dont have anything else in the project other then the menu which is 3 drop areas. Nothing to it.
I tried sharing again from imovie and selected medium this time with a files size of 1.7gig and i still get the same thing.
I do have quality set for PRO.

good question. I used the Theme that has half the screen as a grey fade. When i added music to it i changed it to 25 secs of playback. I would assume then my menu is only 25sec. It only has 1 button to start the movie.
At this point I have a DVD+R DL created that works fine my PC. After googling around I read about DL and changing the bitsetting before burning so that a TV DVD Player sees the disk as a DVD-ROM.
Would I be able to copy this DVD+R DL with Toast 8 and change that setting to make it work?
BTW, thank you for all the replies.
Bill

Outputting a file for dual layer dvd

Hi...is there a setting in Adobe media encoder that automatically caculates your timeline to fit a dual layer DVD? The MPEG DVD output setting automatically shrinks it to 3 gigs, enough to fit a standard DVD. I feel the quality of the file would be better if it was larger and burned to a dual layer.
Thanks

If you're authoring in Encore, you set the Layer Breaks there. You can let Encore find them for you automagically, or you can set your own, or render out your own separate timeline for each layer. Read p.178 of the Encore Help PDF.

Errors burning dual-layer DVD+R's

OK.... this is truly odd.
We are running DVD Studio Pro 4.0.3 as well as Toast 7.1
Whenever we burn a dual layer DVD+R disc from either DVDSP or Toast 7.1 we get an Error -5001 (AFP Authorization continue) failure during the lead-out. The disc mounts and appears to play just fine, but we are very leery about using these as masters.
We have been able to replicate this on every G5 in the studio regardless of burner.
Anyone know what is causing this error?
We are trying to get this disc to duplication ASAP but don't trust these burns.

I have had the same oddness, some things that worked as a workaround
http://discussions.apple.com/thread.jspa?messageID=3236567&#3236567
As to using the DVD+Rs as masters, usually not a great idea ( you mean for replication I take it?) DLTs are usually more reliable, though I have got issues once in awhile with DLTs. Well once actually and it is driving me nuts right now

Compressing 7.5 Hour video for Dual Layer DVD

I've got to compress 7.5 hours of footage into an MPEG2 fittable on a Dual Layer DVD. The client knows that the quality will be inferior. Anyone have any suggestions as to settings before I start? I'm guessing to set the bitrate to 2.3 or so. How about the maximum? Thanks!

I used Compressor and set everything on the MPEG 2 settings to the lowest I could, like 2.1-5.0 and compressed the **** out of it. It looks pretty decent for that much compression. It only fit because I chopped off the credits sequence from the 15 different sections, compressed that seperately, then had them link to it so that it was actually about seven hours of footage. There's a little pixelation when you go into certain motion areas, but the client's happy. I only recommend doing this if there are no other options.
AK

Error Burning Dual layer DVDs

I can burn single layer dvds and cds just fine however every time i try to burn Dual layer DVDs i get error message that there is a hardware failure. I have tried several DVD manufactures to no avail. I finallly had a hunch there was a corrupt file someplace so i created a new user account and burned the file from using Finder and the dual layer burned just fine with my new user account. I repaired permissions on the bad user account (USing the snow leopard dvd and using the Disk utlity) and still no luck. has anyone had or have heard of this issue? Any ideas on how to find the corrupty file causing Dual layer dvd burns to crash? Btw i have used Toast, Finder and Itunes to try and burn the dual layers. Any info on this would be great

Yep, I have the same problem. I've re-booted, check all logs, and I get the same error. I was burning the same file, the first two DVD's went well, then I got the Communication error.
I make a living in Graphics, so my clients have to have the files I've created... This is a MAJOR issue!

How can I burn a 5GB iso to a dual layer DVD (I get a size error..)

I converted a 5GB *.mkv to iso for dual layer dvd with devede. When I try to burn the iso with growisofs -dvd-compat -Z /dev/sr0 /home/hk/movie/movie.iso, I get: /movie.iso is larger than 4GiB-1.
-allow-limited-size was not specified. There is no way do represent this file size. Aborting.
:-( write failed: Input/output error
What could I do? Thank you

Chances are the ISO is not dvd compliant & does not contain layer change info:
http://forum.doom9.org/archive/index.php/t-113514.html
EDIT: Alternative
For the lazy you can install ImgBurn into a Windows NT4 bottle/prefix
then install the latest ASPI.dll
issue a wineboot for the bottle/prefix
then build the dvd in ImgBurn BUT you will need to use dvdauthor to create the correct dvd folder structure & files
http://forum.imgburn.com/index.php?showtopic=1777
Last edited by t0m5k1 (2013-05-22 14:49:24)

Recommendations on Dual Layer DVD Burner Purchase

Anyone have any recommendations on a Dual Layer DVD burner to purchase to replace the old superdrive?

Nope - both formats are for both platforms, but there was a spate of +R players and discs made available on PCs when Apple were only using -R. However, I have two or three PC burners that were -R only (and are now sitting on a shelf somewhere) from those days. The capacity of both is so close as to not be an issue, although +R does hold slightly more data. The gross capacity of a DVD-R is 4.7GB, which is in fact 4.372GB when used in a computer. For DVD+R the gross is 4.73GB which converts to 4.377GB on your computer. I guess for some folk that additional capacity might be necessary, but it isn't really worth worrying too much about, IMO.
Using dual format drives is a good idea, as you can then use either type of disc... however if you read into the background of the formats you'll see that -R is slightly ahead of +R in the compatibility stakes, although more and more players are able to deal with both equally well.
When it comes to burning a DVD in your superdrive, the slower you burn the better the compatibility is likely to be, however some folk report 100% success with fast burns every time (I've had my share of problems with faster burners). As long as you get an Apple compatible drive you should be OK, if faster burning is what you want to do.
Layer break points - on a dual layer disc there comes a point when the laser in the player has to switch from the first to the second layer in order to access the data written there. The point at which this happens is controllable by the DVD author and is called the layer break point. However, on some media (specifically dual layer DVD-R) there is no point in setting this up as the first layer will get written until full, no matter what. There will then be an automatically set break point. When this occurs the change over is flagged as 'seamless' which is intended to make a smooth switch over but there are some players which cannot handle this kind of switch and it needs to be flagged as non-seamless. Other types of media (DVD+R DL) will allow you to set the break point where you want it and will allow you to set it as non-seamless. This helps increase the compatibility of your disc when playing back in set top players.
In DVDSP this means it is probably better to use DVD+R DL media when creating a DL sized project.

Dual layer DVD will not play after iDVD burning

Hi All,
I am having some trouble making a useable DVD. I have a video that I recorded and imported into iMovie (2h33m long). I exported it to iDVD, which told me that I needed to use a dual layer DVD to make it fit. Here's where I noticed the first problem: iDVD has one option for a dual layer disc, stating that it has 7.7GB storage space, and my discs have 8.5GB. I set it to use the standard setting for the DL disc any ways, turned the quality down a bit to make it fit, and burned the DVD. After burning two discs, I still do not have one that works. It comes up as "supported disc not available" on my Mac, and as a blank disc on any other machine I put it in. It will run on my coworker's brand new iMac, but that is the only one. Am I doing something wrong? The only mistake that I have corrected since I have tried all this is changing the aspect ratio back from 4:3 to 16:9 in iMovie (I am not sure how that happened, as the video was originally recorded in 16:9). I am re-exporting the file to my desktop now in the proper ratio, and changed the quality to HD. I am waiting for the file to encode as we speak. Any help would be greatly appreciated, as this work is for my local school board and is very time sensitive.
I am running a 28" iMac, 2.66GHz Intel i5, 8GB RAM, 1TB hard drive on OSX 10.6.8.

I set it to use the standard setting for the DL disc any ways, turned the quality down a bit to make it fit, and burned the DVD.
That part I don't understand.
iDVD encoding settings:
http://support.apple.com/kb/HT1502?viewlocale=en_US
Short version:
Best Performance is for videos of up to 60 minutes
Best Quality is for videos of up to 120 minutes
Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
Professional Quality: The Professional Quality option uses advanced two-pass technology to encode your video (The first pass determines which parts of the movie can be given greater compresson without quality loss and which parts can’t. The second pass then encodes those different parts accordingly) , resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned about the time taken.
In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
http://support.apple.com/kb/HT1502?viewlocale=en_US

Dual Layer DVD Burners? (Best Choices)

What are people having the Best luck with Dual Layer DVD wise?
I have an older G4 (as seen on bottom of post)
I've been reading that the DVD+ format is the way to go as far as Dual Layer DVD is concerned..
Does that mean I wouldn't be able to play it back on my single layer SuperDrive?
Thanks,
Eric

Can't anyone give me a couple of good choices for Dual Layer DVD Burners for the G4?
I know that LaCie makes one, are they're any better choices?
Thanks Again,
Eric
Which model of LaCie, or others are recommended?
(or not recommended?)

Dual Layer DVD Break Point

Hello,
I have been making Dual layer DVDs using the Auto transcoding offered by Encore 1.5, and have been able to select a break point manually for the disc.
I am now looking at using a lower bit rate (The PAL DV High Quality 7Mb VBR 2 Pass) transcoding setting yet it has not given me the option to select a break point!
Just wondered if this has happened to anybody else? Or if anybody knows how to set the break point using this bit rate?
Regards,
Dan
BTW. I hope I have the correct place for this post. If not can somebody please direct me to the correct place, Thanks

Silly question but brilliant answer lol that is the case lol the data is coming out at 4.3Gb on one disc and 4.19Gb on another so I can run with single layer discs :-)
Thanks again, I suppose I should check these things when people ask me for solutions lol although I expect them to check something like that lol
Thanks again
Dan

Formatting Failed Error - Break Point Error

I have a large project I'm trying to burn on a dual layer dvd. I keep getting the following error:
Formatting was not successful. A suitable marker could not be found in the required layer break range. See the DVD Studio Pro User's Manual for more info.
Well I did that and tried to move the break point marker to where I thought the break may occur according to the VTS outline view. I usually use automatic for this but it's not working this time.
Any suggestion would be greatly appreciated. Thanks for your time.

When you prepare to Format the disk: Look at the Disc/Volume tab: Dual-Layer Break Point drop down menu.
Are any of the chapter markers in the middle tracks visible in black (ie not greyed out)? If so select a suitable one of these and you should be OK. If they are all greyed out then you need to create a chapter marker in an area of the movie that should be at about the mid point of the movie. Try to select a point where a slight pause would not be distracting.

Burnning dual layer dvd Encore CS5.5 errors out.

Here is the greatest error I have ever seen.
I got to burn a dual layer dvd transcoded from AVCHD 1080i with fallowing settings.
Edited footage in PPro and send to Encore via Dynamic link, created dvd project using Mpeg2 with 9mbps, Dolby 192 for Audio.
File size to be burned on dvd is 5.67gb, aprox 1 hour 10 min transcoded with 9mbps, 720x40 wide screen, audio is 192kbps Dolby.
There are three menus one is main and tow sceen selection menus, noting fancy everything as default. menus linked as usual nothing fancy and and it is very basic.
All assets, that used for motion menus and main video is transcoded fine, but when it gets to put dvd together I get this error
Encore starts organizing videos for disk and after that it gets to this above and thats it. Press ok Build progress box gives fail message and option to Ok it. After pressing Ok button this box goes away to build panel.
I have tried to change an Automatic layer break to manual still get the same error, I have tried a custom layer break and still get the same error again, I have tried dvd, and an image, and folder for dvd, still the same error there to. I have redone project from scratch and still got the same result.
However previously I have burned many Dual layer dvds using the same method described, and same settings described, and never had this problem.
Nothing on the PS was changed except the updates installed regularly.
Anybody have any Idea what is this all about? Because I just burned 16 Blu Ray discs, and 16 Dual layer discs on one of the project, and next one a day latter this happens.

I'm having the same problem. not once did it, the encore was automatically break in the case of dual layer dvd. now he does not. I mark the box DUAL LAYER 8.54gb, do DVD disc or image or folder, or change the marking of the layer break from automatic tomanual, and it does not. in the end he always gives the message: duallayer requerid.
wanted to know how to do this manually break, because even in the manual or here on the website of adobe, has no suchinformation. does not show clearly how to manually break. please if someone can give a help, thank you.

Suitable marker break point error for dual layer DVD!

Similar Messages

Maybe you are looking for