Sun 7120 - problems with resetting root password?

We have just taken delivery of a Sun 7120 system, did the initial config today no problems, then came to log in to tweak it and it refused my root password. Logged on the serial console with the same password fine, logged out and now it won't let me back in, just says "login incorrect". Have reset the CLR PW jumper on the mainboard, and rebooted and it then comes up in the preboot system, but reports errors about the ILOM. After powering down and removing the jumper, the root password is still there!
Output on bootup attached below, can anyone help?
Cheers
Primary Bootstrap.
U-Boot 1.1.4
Custom AST2100 U-Boot 3.0 (Aug 17 2010 - 01:30:05) r58107
DRAM: 119 MB
Flash bank 0 at 10000000 has 32MB in 256 sectors (chipSize 1<<25, ratio 1, bufSz
1024).
Flash: 32 MB
VUART1 at port 0x03f8, SerIRQ[4] disabled
VUART2 at port 0x02f8, SerIRQ[3] disabled
Protecting U-Boot flash sectors; monitor_base=10040000.
board_findGpioNum(): ERROR, 'BIOS_TOP_BLOCK_LOCK' does not match any pin.
board_findGpioNum(): ERROR, 'SP_PECI_ENABLE' does not match any pin.
H/W: Lynxplus Service Processor; SOC: AST2100 Rev. 02 ('A3')
PWC_SP_Broken_OD = 0; ARM restart caused by: power-on
The host is OFF(S5) (hostWantsPwr=0, powerGood=0,
allowPwrOn=0|0, outOfReset=0, fatalError=0).
Reset straps=0x8c819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal spe
ed
PCI w/VGA noVBIOS; NOR 38ns/byte; DRAM clock is M-PLL: 264 MHz (DDR2-528)
DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us
refr
Board Revision - 8d
Date: 2011-01-19 (Wednesday) Time: 7:04:21
Reading FRUID...Valid CRC.
ethaddr=00:21:28:3D:BD:9A
eth1addr=00:21:28:3D:BD:9B
Net: MAC1 PHY not ready faradaynic#0, faradaynic#1
Enter Diagnostics Mode ['q'uick/'n'ormal(default)/e'x'tended(manufacturing mode)
] ..... 0
Diagnostics Mode - NORMAL
<DIAGS> Memory Data Bus Test ... PASSED
<DIAGS> Memory Address Bus Test ... PASSED
I2C Probe Test - Motherboard
Bus Device Address Result
=== ============================ ======= ======
2 Sys FRUID (U3003) 0xA0 PASSED
2 Power CPLD (U3301) 0x4E PASSED
2 CPU0 Fault LED's (U3001) 0x40 PASSED
2 CPU1 Fault LED's (U3002) 0x42 PASSED
2 PCA9555 (Misc) (U3005) 0x44 PASSED
2 DIMM IMAX (U3102) 0x12 PASSED
6 Bank Panel Led's (U2701) 0xC6 PASSED
6 DS1338(RTC) ( U803) 0xD0 PASSED
6 Temp Sensor1(LM75) (U3011) 0x90 PASSED
6 Temp Sensor2(LM75) (U3012) 0x92 PASSED
6 Temp Sensor3(LM75) (U3010) 0x94 PASSED
I2C Probe Test - Chassis(2U HYDE24)
PDB Board
Bus Device Address Result
=== ============================ ======= ======
1 PCA9548 Mux (U0202) 0xE0 PASSED
1 PDB FRUID (U0203) 0xAA PASSED
1 MAX7313 (U0201) 0x40 PASSED
1 MAX7315 (U1001) 0x46 PASSED
Power Supply 0
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 0 PS 0 FRUID ( - ) 0xAC PASSED
1 0 PS 0 CTRL ( - ) 0x7C PASSED
Power Supply 1
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 1 PS 1 FRUID ( - ) 0xAC PASSED
1 1 PS 1 CTRL ( - ) 0x7C PASSED
Unified Fan Module
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 2 FT 0 FRUID (U0203) 0xAC PASSED
1 2 FT 0 MAX7313 (U0201) 0x42 PASSED
1 2 FT 0 ADT7462 (U0202) 0xB8 PASSED
1 3 FT 1 MAX7313 (U0501) 0x42 PASSED
1 3 FT 1 ADT7462 (U0502) 0xB8 PASSED
24 Disk Backplane
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 BP MAX7313 ( U8) 0x44 PASSED
1 4 BP FRUID ( U6) 0xAC PASSED
LSI Daughter Card
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 EXP FRUID ( U07) 0xA0 PASSED
1 4 EXP Tmp Sens ( U04) 0x98 PASSED
1 4 EXP PCA9538 ( U10) 0xE6 PASSED
1 4 EXP EMP570 ( U05) 0x50 PASSED
Connector Board
BUS Port DEVICE Address Result
=== ==== ==================== ======= ======
1 4 CONN FRUID ( U05) 0xA2 PASSED
<DIAGS> PHY #0 R/W Test ... PASSED
<DIAGS> PHY #0 Link Status ... FAILED
MAC1 PHY not ready <DIAGS> ETHERNET PHY #0, Internal Loopback Test ... RX error
status = 0xB00905C0
FAILED
No data received
<DIAGS> USB 1.1 Test ... PASSED
<DIAGS>Access to BIOS Flash ... PASSED
<DIAGS> Testing PowerCPLD version ... PASSED
checking for abnormal reboots: 0:0.
abnormal reboot found -- too long, ignore
Booting linux in 3 seconds...
Un-Protect Flash Bank # 1
flctrl: Recovery U-Boot (r58107) at 0x10040000 is valid (min. r51654).
flctrl: Current U-Boot is not the main one.
bootpkg: Not safe to boot ILOM (stat=1). Check Preboot "vers" command,
then reload ILOM ("net flash") as needed.
ILOM Pre-boot Menu
Type "h" and [Enter] for a list of commands, or "?" [Enter] for
command-line key bindings. Type "h cmd" for summary of 'cmd' command.
Idle time-out is disabled. Set 'bootretry' to enable it.
This is Recovery U-Boot. Use "vers all" to check flash images.
Preboot> vers all
Main ILOM image at 0x100a0000:
Service Processor Firmware
Version = 3.0.9.27, for SP type 52
Date ='Tue Aug 17 01:54:07 EDT 2010', Build ='r58107'
Name ='sysbios'
uboot @0a0000 OK, kernel @102000 OK, root @20d684 OK,
sysbios @c9b6c4 OK, pwrseq @d51aa2 OK, pbsw @d6096c OK
coredump @1500000 8192 KiB, persist @1d00000 2048 KiB, params @1f00000 1024
KiB
Recovery firmware and data:
Normal U-Boot at 0x100a0000:
Date ='Aug 17 2010', Build ='r58107'
uboot @0a0000 OK
Recovery U-Boot at 0x10040000:
Date ='Aug 17 2010', Build ='r58107'
uboot @040000 OK
Primary Bootstrap build: r52205
Permanent environment: not found

I don't think it is. The jumper you saw is likely the ILOM jumper. The ILOM is different than the BUI(OS) password so they can be reset/changed independently.

Similar Messages

Problem with resetting admin password

I lost my admin password so i booted from the install dvd to reset the password,
the problem is that the Macitosh HD doesn't appear on the list, the only thing on the list is the install dvd.
So I can't reset the admin account on the HDD, can anyone help me with this problem?
Arnootje

Welcome to the Apple Discussions:
In the Utility Menu on the DVD, can you run disk utility and repair HD and permissions?

I have problem with reset my password

please help me , i want to change my password but i forget my security questions answer , and when i request for reset my security question by mail , apple does not sent email for me to change that . in other way to change password i reset password just by email but again apple does not sent reset password email to my primary email , please tell me what can i do ? Thanks

If you have a rescue email address on your account then you've checked the inbox and spam folder on that account for the password reset email - and resetting security questions is done by the rescue email address.
If you still can't find the password and/or security question reset emails then try contacting Support in your country, after confirming your id and that it's your account they should be able to reset them.
Contacting Apple about account security : http://support.apple.com/en-us/HT5699
If your country isn't on that page then try this form and explain and see what they reply with : https://ssl.apple.com/emea/support/itunes/contact.html
When they've been reset, and if you don't already have a rescue email address, you can then add one for potential future use : http://support.apple.com/en-us/HT201356
Or if it's available in your country you could change to 2-step verification : http://support.apple.com/en-gb/HT5570

Problems with the sap* password

Hi,
i have a problem with the sap* password.
I tried my masterpassword but it did not work.
So i tired the following from the Tread: Password problem with user DDIC
resetting password for sap*
sqlplus "/as sysdba"
sql> update sapsr3.usr02 set bname='SAP1' where bname='SAP' and MANDT=000;
sql> commit;
Bud it did not work. After i tried to delete the sap*1 from the table sapsr3.usr02 but it did not work.
sql>delete from sapsr3.usr02 where mandt='000' and bname = 'SAP*1';
I also restarted the instance after the commands. But i can not logon with 'sap*' and the password 'pass' .
Mybe someone can help me?
Regards
Mike

Starting with release 7.00 based system you have to set
login/no_automatic_user_sapstart=0
in your instance profile and restart the instance.
Markus

Having problems with key chain password

I just got my mac book yesterday, and I'm having problems with my keychain password.
My keychain password is not the same as my login password, it won't accept it, so i think i made a typing error.
Each time i go on to safari, it asks for the password, which i don't have. i've tried the key chain first aid, and that still doesn't work. I've also tried keychain access, and that also doesn't work as it asks for the password first!
Is there a way that i can reset it?

There are user passwords and Administrator passwords. The only way to check your keychain password is to be the administrator. In an effort to secure my MacBook, I have an administrator account that I don't use at all and I have a user account that is all I use. It is a great way to protect your MacBook info from others.
As to your question, passwords are case sensitive. You can try to change the password by inserting the CD's that came with your MacBook and reset the password. Seeing that you just got it yesterday, you probably don't have much personal information on it yet, you could use disk utility from the CD and reinstall the Operating System.
Good Luck.
Adam

Problem with AppleID login password

Hi - I'm from Europe. How can I contact talk to a real live person from "nonstop " customer support service - I need help - have problem with AppleID login password

DanielBuggati wrote:
Hi - I'm from Europe. How can I contact talk to a real live person from "nonstop " customer support service - I need help - have problem with AppleID login password
Have you tried MyAppleID <<== click this
There is a link there for "Forgot your Password?"

I'm having problem with my bios password. It tells me to enter current password 100-10250x

Having problem with my bios password.it tells me to enter current password 110-10250x

Place the iPod in recovery mode and restore via iTunes on your computer. For recovery mode see:
iPhone and iPod touch: Unable to update or restore

Problems with reset password

Hi all, I wanna ask support for my other account Skype where I can't reset my password. I try to reset it with my email and when I inserit new password the system give me problem and I can't log in to my account. Why? Why I can't use it anymore? Pls help me! It's a week that I can't use it! I can't remember all of my data to ask support for email... How I can do? I'm really desperate!

The passcode you need is the four digit number that you enter after an Autolock on your device or when you first turn it on. If you can't remember that code you'll have to restore your iPad before you can do the update.
http://support.apple.com/kb/HT1212

Resetting root password

Hi
I have a Sun Ultra5 Server running solaris 2.6. I have lost the root password and would like to reset it. Does anyone know how I can reset the root password? I have a bootable Solaris software CD.
Thanks
Richard

Hi Richard,
It is good to know that you have a bootable cd.
Well to start with don't if you have lost the root password.
We can reset the password.
Way to reset the password.
1. boot the system to come in ok prompt.
2. then boot from cdrom in single user mode.
3. after booting from the cdrom mount the file system (root file system c0t0d0s0) which contains the etc\shadow,password ... files.
4. then vi the shadow file and remove the password.
5. save and come out.
6. reboot the system. you login as root then you will be promped as to give new password.
7. So here give the new password.
Warm Regards
Sridhar M
Hi
I have a Sun Ultra5 Server running solaris 2.6. I have
lost the root password and would like to reset it.
Does anyone know how I can reset the root password? I
have a bootable Solaris software CD.
Thanks
Richard

MDS Customization Problem with multiple root components

Hello,
Oracle JDeveloper 11.1.1.5.0 and WebLogic Server Version: 10.3.5.0
I am using Oracle MDS Customization class with the following classes:
oracle.adf.view.rich.change.MDSDocumentChangeManager
org.apache.myfaces.trinidad.change.ChangeManager
org.apache.myfaces.trinidad.change.MoveChildComponentChange
Based on these classes I am moving UI components
<af:panelStretchLayout>
<f:facet name="center">
<af:region />
</f:facet>
</af:panelStretchLayout>
into another component thanks to the MDS.
Once I do the movement and persist, I receive the following waning message:
*<RegionRenderer> <encodeAll> The region component with id: pt1:r1:0:pt2:r1:0:r1 has detected a page fragment with multiple root components. Fragments with more than one root component may not display correctly in a region and may have a negative impact on performance. It is recommended that you restructure the page fragment to have a single root component.*
When I run the application in Oracle JDeveloper 11.1.1.5.0, it work fine, but when I deploy it on WebLogic Server Version: 10.3.5.0 it is not working.
I receive the same warning message on the server and in JDeveloper.
I think that MDS makes a copy of the components that I move because of that it says me that "a page fragment with multiple root components"
The problem is not because of duplication any of the tags <af:document> <f:view><f:form> <html> <head> <body>
After the movement and persistence, I also call the FacesContext to reset its view root with the following code:
FacesContext context =FacesContext.getCurrentInstance();
String currentView = context.getViewRoot().getViewId();
ViewHandler vh = context.getApplication().getViewHandler();
UIViewRoot x = vh.createView(context, currentView);
x.setViewId(currentView);
context.setViewRoot(x);
The idea is that the entire JSF tree to be rebuild on entering page with aim to clear previously drag and drop settings.
Do you know how I can overcome the problem on the server WebLogic Server Version: 10.3.5.0?
This worked on Oracle JDeveloper 11.1.1.3.0 and now the problem is with Oracle JDeveloper 11.1.1.5.0.
Regards,
Niki

Hi,
what the error means is that you have more than one node under the jsp:root node of the fragment. Say the content of your fragment is
<af:panelGroupLayout id="pgl1">
</af:PanelGrouPLayout>
Then this is okay
if you have
<af:panelGroupLayout id="pgl1">
</af:PanelGrouPLayout>
<af:panelGroupLayout id="pgl2">
</af:PanelGrouPLayout>
or
<af:panelGroupLayout id="pgl1">
</af:PanelGrouPLayout>
<af:commandButton id="cb1"/>
Then these mean duplicated root components. The JDeveloper IDE flags this as Warnings (Structure Window) when selecting the page fragment
Frank

Newbie:Problems with SCSI root disk

Hello
I have periodic problems with no matter what disk I put in my root partition. My Sun has several disks, so I can take another disk not being used and configure it as my new root disk, installing Solaris root on it.
But when, this way, I replace the disk by another "fresh" disk and reinstall Solaris all goes Ok during some time (days or months) until suddenly I get I/O Errors allways in that disk.
I use a E250 with Solaris8. The problem also arises with Solaris7.
If I do a probe-scsi-all at ok prompt I frequently see hardware errors in that disk. All those errors where not present previously when my disk wan't the root.
What is corrupting my disks a I use them?
Am I missing something when I put a new disk? Should I change the ID of my previous SCSI disk?
If so, how?
Thanks

Are you using the disks in the same slot? It may be the controller....

Apple ID Problem with Incorrect username/password setup

Hello all,
I'm trying to help my sister-in-law with a problem with her Login details for Apple Store. She has no skills in this department, so she asked a friend (?!) to help her. Somehow things were done that allowed her to establish an account, altho frankly I am not sure how it was activated. She used her old email address at that time, which she has in the meantime replaced with a new address from another ISP. I managed to establish an ID using the new address, but she has an iPad registered under her old Apple ID.
Nothing was written down, and nowhere can I find an 8 letter password with the Capital Letter and Number system as required by Apple. The help questions which were established when compiling the old address can't be answered, because she didn't write down either the data, or the answer. From all this, you can judge that I'm frustrated at trying to do more for her.
I can't understand how, or if, one could cancel the old details in favor of the new. Or whether it might work if I "Restore" the iPad according to the instructions in iTunes when the iPad is attached, and try to register it under the new user/password I established.
We live very remotely, so popping into a local store for help is not possible. I've tried, with my limited knowledge, everything I can, but I've got nowhere. So, can any kind soul who might have had to go done this route, or who might have a possible clue to what I could do, perhaps help me out? I'll bet its staring me in the face, but as an old guy, my instincts aren't as sharp as they were.
Very many thanks to anyome reading this post, who might be able to give me some assistance.
Barrie

Hi barrie,
Well, sounds like you have half the problem fixed. But for the original account, even though you can't remember the answers to the original security questions, you CAN contact Apple Support to have them reset them for you. Once they are reset, also reset the password to whatever the password on the new account is so they are seamless.
Also, on both accounts be sure to set up a RESCUE EMAIL ADDRESS with the Security Questions. This will prevent any issues down the road with forgotton passwords/security questions, and will allow you to recover in a much easier way than this has been.
But again, for the original account. You need to do the following:
1. Contact Apple Support, provide them with the Original Apple ID, and let them know that you need to have the Security Questions reset.
2. Once that is done, set up new Security Questions for that old Apple ID as well as a RESCUE EMAIL ADDRESS with those new Secuity Questions
3. Reset the Password on that Old ID to be the same as the one on the new ID (and keep it consistent - any time you change the new one, change the old one)
4. Sign into iTunes one last time with that old ID and use up your $15
Now, forget the old ID altogether except when you need to update the password to match the new one. Once you have done your final redemption, only the new Apple ID should exist for you. All apps and music purchased in the same iTunes Library with either ID will be able to be loaded onto the iPad. When one of the apps needs to be updated, it may display the old ID, or it may display the new ID - if the password is the same, it won't matter which is displayed for the update. Put in the password, and it will update.
Whatever you do - Don't delete the apps purchased with the old ID. Once you get it squared away it will just be like a "phantom" id in the backround. Not really used, but still associated with the apps purchased under it. As long as they all live in the same iTunes Library, the ID they were purchased under is irrelevant. The only thing that matters after that is the password (as explained above) for any updates.
For the iPads themselves, make sure that the new Apple ID is showing for the iCloud account. This is what ties the Apple ID being used to do purchases via the iPad.
I hope the info I have provided has helped, and that your trip to Canberra will be a success. Sounds like an all-around nightmare, and you have been a very patient and sweet brother-in-law to stick with this whole thing.
Best of luck, and do let me know how it all turns out! I would love a line from you as the adventure progresses!!!
Cheers,
GB

Cannot reset Root password from Leopard installation DVD

User installed Leopard with the Upgrade option, and discovered his administrator user account had been reset to standard, as described in
http://docs.info.apple.com/article.html?artnum=306876
However, when the user tried to follow the instructions for the password reset utility, he discovered that the User account selection pull-down was grayed out. So he cannot select the Root user, or any user account to reset the password.
All user account have been set to standard and there appears to be no Root user.
What next?

Sorry. Wrong forum. Reposting.

Paasword Probleme to reset my password

Hello everybody ,
I got a probleme with fim password reset portal , i can register my question it was successful . Then i went to to password reset site i answer to the question then i had to text my new password and confirm it again so after that this message apear :
The error page was displayed to the user. Details: Title: Erreur Message: Une erreur s'est produite. Réessayez. Si le problème persiste, contactez le support technique ou l'administrateur système. (Erreur 3000) Source: Attributes: Details: System.InvalidProgramException:
Error while performing the password reset operation: PWUnrecoverableError à Microsoft.IdentityManagement.CredentialManagement.Portal.Reset.AttemptToResetPassword() à System.Web.UI.WebControls.Button.OnClick(EventArgs e) à System.Web.UI.WebControls.Button.RaisePostBackEvent(String
eventArgument) à System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) à System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) CorrelationId: RequestId:
ErrorCode: 3000 CaughtTime: 02/19/2015 17:34:24 Web Portal: FIM Password Reset Portal Session Id: jb2x2w45naffyi451tozvsur IP Address: fe80::3d7b:6642:c540:80c3%12
Can someone help me please

Hello,
Jorge wrote a large blog post just about this error yesterday:
https://jorgequestforknowledge.wordpress.com/2015/03/08/resolving-the-pwunrecoverableerror-error-with-fim-self-service-password-reset-sspr/
Maybe this help.
-Peter
Peter Stapf - ExpertCircle GmbH - My blog:
JustIDM.wordpress.com

[Solved] Reset root password

Hi folx
I need to reset the root password. I tried going into GRUB and appending the relevant line with:
(1.) single
(2.) 1
(3.) single init=/bin/bash
Result:
(1.) asked for root password during boot
(2.) asked for root password during boot
(3.) didn't get that far as it went into kernel panic
I downloaded Ubuntu 8.10 desktop to use as a live CD, but that didn't work as the CD just dumped me into an initramfs session.
How am I supposed to reset my root password?
Thank you, wickyd.
Last edited by wickyd (2009-03-19 07:38:14)

this has all been discussed before - ad nauseatum
1) boot up with _any_ live cd
2) mount your root filesystem as - say - /mnt/fs
3) vi /mnt/fs/etc/passwd
change the first line to:
root::0:0:root:/root:/bin/bash
4) unmount /mnt/fs and reboot
5) you can now log in as 'root' with no passwd
6) pwconv && passwd (now set new password)
<edit>
With all due respect - chroot is _not_ the way to go.
In order to actually _set_ a new password, you have to run the same kind of
authorization as in your present system - it may be different for different distros.
</edit>
Last edited by perbh (2009-03-18 16:49:01)

Sun 7120 - problems with resetting root password?

Similar Messages

Maybe you are looking for