Sun 9 x86 - Problems after install

Hi folks,
Finally, I have installed Sun 9 intel - but... it cannot enter graphical mode - usually says: "Desktop mode suspended" and brings me to console mode. Plus it has constant problems - when display blinks. Ocassionally it hangs up and I have to reboot it.
I used "b kadb -v " - it should:
" ata_set_feature: (0x66,0x0) failed"
and also
WARNING: /pci@0,0/pci-ide@1f,1/ ide@0 (ata0):
timeout: abort request, target=0, lun=0
WARNING: /pci@0,0/pci-ide@1f,1/ ide@0 (ata0):
timeout: abort device, target=0, lun=0
WARNING: /pci@0,0/pci-ide@1f,1/ ide@0 (ata0):
timeout: reset target, target=0, lun=0
WARNING: /pci@0,0/pci-ide@1f,1/ ide@0 (ata0):
timeout: reset bus, target=0, lun=0
Could someone say what to do?
Thanks for your help...

Here is another group that is moderated by Sun Employees...
http://supportforum.sun.com/cgi-bin/WebX.cgi?[email protected]^0@/os.install.solaris_x86
I realize its an S8 group but it seems to answer some questions....search the forum...here is an extract of a similar issue posted by a Sun Technician...
Try installing the latest revision of patches 108529 and 111307 for ACPI bugfixes. If you are booting from floppy, use the boot image from patch 110930.
From SunSolve FAQ 3307:
SYNOPSIS: How to resolve ACPI conflicts.
DETAIL DESCRIPTION:
ACPI is a new device enumeration method on the Intel architecture. At times
messages noting a conflict of some type may come up:
Warning: resource conflict... both devices are added
NON-ACPI device: ISY0050
Port: 3F0-3F5, 3F7; IRQ: 6; DMA: 2
ACPI Device: ISY0050
Port: 3F2-3F3, 3F4-3F5, 3F7; IRQ: 6; DMA: 2
This is an example conflict. Many other types are possible. In general,
theses types of problems are caused by hardware problems or a buggy ACPI
implementation.
SOLUTION SUMMARY:
A possible workaround is to disable the kernel ACPI module. If the problem
is happening during installation, the boot floppy must be modified. Mount the
boot floppy and add the following line to bootenv.rc:
setprop acpi-user-options '0x2'
Run the installation again, ACPI should be disabled and the installation
should continue without a problem.
If the problem occurs after installation the same line can be added to
the top of /etc/bootrc and ACPI will be disabled on the next reboot.
Hope this helps..
Lee

Similar Messages

A lot of problems after installing Windows XP using Boot Camp on a Mac Book

I have been having a lot of problems after installing Windows XP Home Edition (2002).
For one, after installing Windows using Boot Camp with Mac OS X 10.5.1, I opened Windows on my Mac Book, inserted the Mac OS X Disk 1 as in the instructions and got the message: +"This package requires a newer version of the Windows installer. Do you want to update the version of the Windows Installer on your system?"+ When I clicked Yes (I had NO idea what it meant at the time), I got the message: "The required resource 'UPDATE' is missing" and the Installer quit.
How do I fix this problem?
Another problem I have is that there is no sound on the Windows XP, yet it works perfectly on Mac OS X. Is there any way to fix this problem?
A third problem I have is that I can't wirelessly connect to the internet using Window XP, yet I can on Mac OS X. I have no idea on how to fix this, and it's really messing with me. D:<
D: There are way too many problems, and I have a feeling there will be a lot more later on. Help....
~Twilight

---I'm moving this topic to the Boot Camp forums.
-Twilight

I see that i have a problem after installing my new hard drive on my macbook pro mid 2009 version. I put a new hard drive, with all of my information from my old drive installed on it, into the computer. but now have the blinking question mark folder

i see that i have a problem after installing my new hard drive on my macbook pro mid 2009 version. I put a new hard drive, with all of my information from my old drive installed on it, into the computer. but now have the blinking question mark folder. I see that it means that it isn't reading the new hard drive.
did i miss a step between transferring all of my information from my old hard drive to the new hard drive and installing the new hard drive into the computer. I believe that i installed properly. it was quite easy.
thanks for your help

It means there is no bootable system on the drive. If you still have access to the old drive, then I suggest you boot from it then clone it to the new internal drive. Use OPTION boot to boot from the Recovery HD on the old drive:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
     1. Select Disk Utility from the main menu then press the Continue
         button.
     2. Select the destination volume from the left side list.
     3. Click on the Restore tab in the DU main window.
     4. Select the destination volume from the left side list and drag it
         to the Destination entry field.
     5. Select the source volume from the left side list and drag it to
         the Source entry field.
     6. Double-check you got it right, then click on the Restore button.
Source means the external old drive. Destination means the new internal drive.

Printing problems after installing the Epson Printer Driver 2.16

Has anyone experienced any problems after installing the Epson Printer Driver 2.16 through Software Update? I am having problems printing. It denotes an error message, specifically the rastertoescpii.app isn't working?

Oops, wanted everyone to know that the driver that Software Update downloaded and installed was 2.18, not 2.16 (which was the last one that worked for me). I just got done downloading the 2.18 driver directly from the Apple support website and installing it. Guess what? My printer is now working and everything is fine. If you are having issues, I suggest this route. Guess I solved my own problem, but hope this helps someone else.

Problem after installing 10.4.8

Hello,
I installed the 10.4.8 update today. I have a brand new macbook. When the update finished downloading, my screen just turned blank, my computer didn't react at all. I could hear the fan and that was it.
So, I waited for some minutes, nothing happened. I decided to restart it by pressing the power button for a few seconds.
The computer is working perfectly now and the update was installed. But, how do I know if my computer or the HD were affected? I ran the HD test and it says that the HD seems OK.
Is that a problem with my computer or is it because of the new update? I read a posting that mentioned similar problems after installing the new update.
Thanks...

How did you update? Mac OS X 10.4.8 Update (delta)?
http://docs.info.apple.com/article.html?artnum=304200
After installing the delta version of this update on an Intel-based Mac, the computer will restart two times--the first restart after installing this update may take several minutes; please allow it to complete.
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
ITMS: MacOSG Podcast
 An Apple User Group 
2.0 MacBook • 100GB HD • 2GB RAM Mac OS X (10.4.7) 60G Photo iPod • AppleCare

Great Problemes after installing Yosemite (10.10.2 ) with Photoshop CS6....The program crashes --last time 10 times during my work session..wacomtable doesnt work..it is slow...and get error messages about the graphic card....It s a Terror to work with my

great Problemes after installing Yosemite (10.10.2 ) with Photoshop CS6....The program crashes --last time 10 times during my work session..wacomtable doesnt work..it is slow...and get error messages about the graphic card....It s a Terror to work with my beloved Photoshop!

The Yosemite upgrade very often damages existing Photoshop installations. Thank Apple for that.
You need to uninstall and re-install Photoshop, then apply all the Photoshop upgrades from scratch.
But first, give us details about your setup:
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

DVD drive problem after installing 10.5.6

I have MacBook Pro 15",
Model Identifier-MacBookPro 2,2,
Intel Core 2 Duo 2.16 Ghz
Problem: After Installing 10.5.6 from the software update panel, my dvd drive (MATSHITA DVD-R UJ-857D) make eject sounds (sound like ejecting disc) every 10 seconds..
But if I insert cd or dvd disc into the drive, every thing is ok - no sounds, and no ejecting the disc..
Before I install this update, everyting was ok!
Please Help!!
P.S Sorry, for my english

Hi Drug;
Have you tried resetting PRAM by holding down control, option, P and R during reboot?
Allan

Hi I have a problem after install my CS6. It keeps saying MSVCR100.dll was not found

Hi I have a problem after install my CS6. It keeps saying MSVCR100.dll was not found?

32-bit OS: http://www.microsoft.com/en-us/download/details.aspx?id=8328
64-bit OS: http://www.microsoft.com/en-us/download/details.aspx?id=13523

Problem after installing IOS 8.0.2

Hi there,
I have a big problem after installing of IOS 8.0.2 on my Ipad mini retina. There is no any internet connection for the applications like ITunes, App store, Facebook etc. Who can help me please for this matter? or how can I get back my previous version?
Thanks for the sopport

Hi there,
I have a big problem after installing of IOS 8.0.2 on my Ipad mini retina. There is no any internet connection for the applications like ITunes, App store, Facebook etc. Who can help me please for this matter? or how can I get back my previous version?
Thanks for the sopport

Out Of Frequency problem -- After Installing solaris 10 x86

Hi Solarians,
After installing solaris 10, I am getting "*Out Of Frequency*" problem and I am not able to login to Desktop session. Please let me know configuration changes that i need to make along with exact paths as i am new to solaris.Currently i am running dual OS (XP and Solaris).
Out of Frequency
HF: 42.7 KHZ
VF: 40.0 HZ
Operating Frequency
HF: 30 - 71 KHZ
VF: 50 - 160 HZ
Please help me solve this problem, Thanks in advance .....
Thanks,
Mahesh

hi;
I faced that problem when I was a beginner on solaris as you were. I tried to install solaris to my windows installed x86 based PC. in my fisrst few attempts ý always saw that message, afterwards somehow I managed to install solaris to my PC but this time windows failed.I think that is because of the inconsistencies between those OS but if you need to install solaris you can use VM ware workstation with this software you can use both OS without problems.

Hard disk problem after installing Solaris 10 u5 on a Sun Ultra 24

Hi.
After receiving a new Sun Ultra 24, shipped with Solaris 10 u4, the first thing I did was installing Solaris 10 u5. X wouldn't start but that was not a big problem and installed it in text mode. Installation went fine but, when the system starts, a single beep is heard and after some seconds some warning message appear on the console, before the "Hostname: ..." message, informing that some read operation on my hard disk had timed out and were aborted. The system then starts up normally. The only other anomaly is that the diagnostic partition in unbootable.
I ran the hard disk tests from the tools and drivers CDs and all of the tests were passed. Solaris 10 u4 was working normally so I'm wondering if this may be a bug.
Thanks for your help,
Enrico.

Thanks anyway, I discovered what the problem was: a bug in Solaris 10 u5:
http://opensolaris.org/jive/thread.jspa?threadID=58768&tstart=75
http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6536722
Thanks,
Enrico

Strange problems after installing Solaris 10 u6 on 64-bit PC

Hi all,
I have run into some very strange issues after installing Solaris 10 update 6 on my 64-bit PC (it's almost new). The problems are with graphical applications and desktop environments based on GTK (so it seems, at least).
I have installed Solaris normally, following most of the default options and choosing the "Entire Group" software packages installation. However, after the first login I've seen that:
1. No user creation process was offered to me and I had to login as root (I find it pretty strange)
2. After logging in as root into JDK system, my screen went blank for a couple of seconds and then the system threw me back to the login screen.
3. Logging into the old CDE environment was possible, but launching Firefox from there (using a command line terminal) wasn't. It gave me the following error message:
ld.so.1: firefox-bin: fatal: libmlib.so.2: open failed: no such file or directory
ld.so.1: firefox-bin: fatal: relocation error: file /usr/bin/firefox/firefox-bin: symbol gtk_init: referenced symbol not found.
It's very strange because GTK toolkit and JDK environment are supposed to be the core functionalities provided by Solaris. Does anyone have an idea what's going on?
My system sum-up:
CPU: Intel Core 2 Quand Q6600 @ 2.4 GHz
RAM: 2 Gb of DDR2 SDRAM
Motherboard: MSI MS-7529 (Intel G31 chipset)
Monitor: AOC LM725
Graphics card: NVIDIA GeForce 9400 GT
Hard disk: 2 Western Digital HDs (SATA) 320 Gb each,
1 Western Digital external USB HD MyBook Essential 2, 500 Gb
DVD drives: 2 LG DVD drives (SATA)
Network card: Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
I use my system in the following way:
On the first hard disk, I have a one-partition 32-bit Windows XP SP3 installation (ported from my old computer).
On the second hard disk, I have a functioning Fedora Core 9 installed on the first half of the disk's space (the installation is self-organized into several Linux partitions, e. g. /boot, /swap etc; I am a newbie so I don't know too much about Linux partitioning - only specified to Fedora how much space it could use for its volume group). I installed Solaris onto the second half of the second disk.
It has be noted that my USB external drive seemed to conflict with the network or graphics cards during the Fedora installation and caused it to hang sporadically, so I installed Fedora with this disk detached. I also detached it when I was installing Solaris, though it seems to have not influenced the problems I experienced. I also have attempted installing Solaris before I did so with Fedora, but had the same issues.

Well, it seems that the cause of the problem was that my DVD image was just corrupted - I didn't check it vs MD5 codes supplied by Sun assuming it went automatically OK. I downloaded the image again (this time it was OK), reinstalled the system and successfully logged into JDS. However, I am still puzzled why Solaris doesn't offer to create a default non-root user during the installation process.

Problem after installing OBI SE 1 to connect to dashboard. odbc

Hi,
After installing OBI SE 1 10.1.3.2.1 I try to open Oracle BI interactive dashboards (http://localhost:9704/analytics/saw.dll?Dashboard)
I am not able to do this, because of the following message HTTP-Error:500: Internal server error.
I found in C:\oracle\bise1\bidata\web\log the file sawlog0.log, In there I found the following lines:
Allocation of SQLEnvironment failed (SQLError: -1). Please ensure that the odbc driver is in your environment path.
ODBC driver preload failed. ODBC library name: 'nqsodbc.dll'
This file is placed in the directory C:\oracle\bise1\bi\server\Bin, which is in my environment path.
Path=C:\oracle\bise1\bi\server\Bin;C:\oracle\bise1\bi\web\bin;C:\oracle\bise1\bi\web\catalogmanager;C:\oracle\bise1\bi\SQLAnywhere;C:\oracle\bise1\jdk\bin;C:\oracle\bise1\db\bin;C:\oracle\bise1\owb\bin;C:\ora102gclient\BIN;C:\Ora817\Apache\Perl\5.00503\bin\mswin32-x86;C:\Program Files\Oracle\jre\1.1.7\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\Symantec\pcAnywhere\
What Can I do to solve this problem?

Are you sure that you edited the config file where you have to make sure that the parameter
STAR = <yourrepository>.rpd ,DEFAULT
is set to your metadata file.
Location of the file on my system is
C:\obiee\Server\Oracle_Business_Intelligence\Config\sarootdir\server\Config\NQSConfig.ini
I hope this helps

Serious problem after install 126670-01 patch

Hi!
After install the 126670-01 patch (who replace the file /kernel/drv/sparcv9/scsi_vhci) the system can not boot:
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'scsi_uscsi_alloc_and_copyin'
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'mdi_pi_kstat_create'
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'mdi_pi_kstat_exists'
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'scsi_uscsi_copyout_and_free'
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'scsi_uscsi_handle_cmd' I uses the smpatch update and shutdown -i 6 -g 0 -y to install this kind of patch.
The only required pacth (120011-14) was installed before...
This bloody patch breaks all the systems where was installed and the only solution was replace the file from other unpatched system (booting using the installation DVD).
If anybody have any idea about how fix this problem, thanks in advance....
H.
Edited by: h.molina on Oct 8, 2007 12:26 PM

I had almost the same problem after patching a Sunblade 100. After following Matt's link, I found out that we had patch 125081-16 installed.
I booted it off the net, mounted the root filesystem, and patchrm'd 125081-16.
A reboot reconfigure and the system was back up again.
Here was the exact error I had:
Boot device: /pci@1f,0/ide@d/disk@0,0:a File and args:
SunOS Release 5.10 Version Generic_118833-36 64-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'mdi_pi_kstat_create'
/kernel/drv/sparcv9/scsi_vhci: undefined symbol 'mdi_pi_kstat_exists'
WARNING: mod_load: cannot load module 'scsi_vhci'
scsi_vhci: cannot load driver
WARNING: Cannot load drv/scsi_vhci
Can't load the root filesystemEdited by: Buffics on Apr 4, 2008 11:22 AM

Problems after installing Bootcamp 3.1

Hello everyone.
I had installed Windows 7 64 bit Ultimate in a Bootcamp partition. I used the SL disk to install Bootcamp 3.0 which, with some audio related problems which were solved by changing the drivers, worked well. All sounds played, the graphics card behaved normally, etc.
Recently I got the alert of a Bootcamp update, 3.1, as we all know. After installing it without a hitch, small problems began to pop up.
First, no Windows startup sound played anymore, and there has been no way for me to make it work again. I've gone to countless forums and gone through an endless barrage of suggestions, including a complete formatting, but it always leads back to the same, isolated problem: Startup sound plays in BT 3.0, doesn't play anymore in BT 3.1.
But more importantly, after pretty much giving up with the startup sound issue (it's only that particular sound, in the login screen, so I decided to ignore it's absence), more problems appeared. Initially, all system tray icons appeared swiftly. Now the main ones, Sound, Wireless Connection and Battery appear fast, but the rest take at least 5 minutes to appear. This is again something that wasn't present in Bootcamp 3.0.
Yet another problem, this one I consider is the most important, and the real reason for this post of mine, is that Bootcamp 3.1 brought a serious driver problem with my Macbook Pro's 9400M video card. Doing the most stupid of tasks such as opening the video card's control panel from the Desktop gives me the following error:
"The NVIDIA Display Panel extension cannot be created.
Possible reasons include:
Version mismatch. Reinstalling the drivers may solve this problem."
Now, the Device Manager shows no errors in hardware-driver smoothness in any aspect, yet it's clear that the driver that BT 3.1 installs for the video card was either faulty or old, or for another OS. I went to NVIDIA's site to manually get the driver, but it turns out that they offer no NVIDIA GeForce 9400M drivers for Windows 7 64 bit. So I wonder, how come it worked before? Because in Bootcamp 3.0 the Control Panel would open flawlessly.
So this is serious. Gaming has also turned into a nightmare, since the problem with the video card negatively affects the smoothness of the gameplay. Apple, things weren't working 100% with BT 3.0, but BT 3.1 far from making things better just got everything worse.
I ask everyone here if there is a known solution. Should I install the NVIDIA GeForce 9400M drivers for Windows 7 32 bit? Why doesn't the driver installed by BT 3.1 function as it should when it's supposed to be covering Windows 7 compatibility? Why are the barrage of audio errors present in BT 3.1 and not in BT 3.0? What happened with my startup sound?
Apple, you're offering the possibility for your users to user Windows for compatibility and gaming. You market your Macs are fully compatible and flawless even running Windows. Don't come about saying this is not your problem, it is. It's your drivers, you develop them, you give them to us. If they don't work, you must do something about it. If not, then stop offering the Bootcamp service completely. If you're gonna do something, do it well.

http://www.nvidia.com/object/notebookwinvista_win7_x64_195.62whql.html

Sun 9 x86 - Problems after install

Similar Messages

Maybe you are looking for