Sun Cluster 3.0 update 1 on Solaris 8 - panics!

I am building a test system in our lab on admittedly unsupported hardware configurations but the failure wasn't expected to be so dramatic. Setup as follows:
2x E250 (single processor, 512 MB RAM)
dual connected to D1000 fully populated 18 Gb HDD
Solaris 8 6/00 with all latest recommended patches
Sun Cluster 3.0 update 1 installed with latest patches.
On first reboot (on either node), the kernel panics with the following:
panic[cpu0]/thread=3000132c320: segkp_fault: accessing redzone
This happens straight after the system sets up the network and happens like that everytime and is easily reproduceable. My question is, has anyone successfully used SC3.0 update 1 on Solaris 8 6/00? Any information would be most appreciated.
-chris.

We have the same problem with 2 SUN E420 and a D1000 storage array.
The problem is releted to the settings on the file :
/etc/system
added by the cluster installation :
set rpcmod:svc_default_stksize=0x4000
set ge:ge_intr_mode=0x833
the second one line try to set a Gigabit Ethernet Interface that does not exist.
We comment out the two line and every things work fine.
I'm interesting to know what you think about Sun Cluster 3.0. and your experience.
email : [email protected]
Stefano

Similar Messages

Is Veritas- or Sun Cluster needed for RAC in a Solaris Environment

Is a Veritas- or Sun Cluster needed for RAC in a Solaris Environment?
Does anyone know, when OCFS will be available for Solaris?

You don't need Veritas Cluster File System, but until OCFS comes out for Solaris you need to think about backups. If you've not got a backup solution that can integrate with rman for an SBT device then backups become more tricky.
If you use ASM then you can take a backup to a "cluster filesystem" (although ASM is raw partitions think of it as a cluster filesystem), that both nodes can see. BUT you then need to get these to tape somehow, unless you've got NetBackup et al. that support RMAN and can backup direct to tape you're more stuck.
Too many people don't think about this. You could create an NFS mount and backup to this from the nodes.

Failed to install SUN cluster 3.1 8/05 on solaris 10(x64)

I install the cluster 3.1 u4 on two nodes(node1 and node2) by using "scinstall".( The two nodes have the same system) After cluster installed, i reboot node2 . Before rebooting, I have done the following operation.
# echo "etc/cluster/nodeid" >> /boot/solaris/filelist.ramdisk
# echo "etc/cluster/ccr/did_instances" >> /boot/solaris/filelist.ramdisk
# bootadm update-archive
updating /platform/i86pc/boot_archive...this may take a minute
# init 6
But node2 crashed,and failed to reboot.
I could only see several characters "GRUB" in the screen. The system even doesnot present the grub menu.
The system i used:
bash-3.00# prtdiag
System Configuration: Sun Microsystems Sun Fire X4200 Server
BIOS Configuration: American Megatrends Inc. 080010 08/10/2005
bash-3.00# uname -a
SunOS arcsunx42km0838 5.10 Generic_118855-19 i86pc i386 i86pc
Message was edited by:
skyqa
Message was edited by:
skyqa

The only thing I can find that is vaguely similar is where users have installed -19 of 118855 but not updated all the other patches on the system. I would try booting from the failsafe mode, if you can get to this. Then update all the patches.
If you can't I guess you are going to have to either boot from DVD and fix or just rebuild.
Tim
---

Sun AppServer 9.0 Update 1 on Solaris not supporting form-based auth

Ok, I installed Appserver 9 on a Solaris box and then started up the default domain1. When I point the browser to http://localhost:4848 I am not pointed to the login page for the admingui, it just bypasses the authentication and I am allowed to perform all admin actions without logging in. I then deployed a custom web application that uses form-based authentication that works correctly on Sun Appserver 8.1. However it behaves the same way as the admingui application (I am not presented with a login page). After setting some of the log levels to FINEST and looking at the logs it appears that when these requests are coming in they are not matching any constraint (but the constraints are defined in the web.xml). Installing Appserver 9 on a win2k box does not have this issue. Has anyone else seen this problem? Is there some security setting that is not turned on by default from the solaris install????

Ok if anyone is interested I was able to fix my problem. It looks like the issue is the version of java used with Appserver 9 on Solaris. The latest version of java i have on the machine is Java 1.5.0_06, but everytime I try to install the Appserver with this version it hangs at 39% into the installation. The next latest version of Java i have on the machine is 1.5.0_02, so that is the version I was using to install and the install works perfectly. However, after the install the form-based authentication does not work with this version of Java on Solaris.
They way I fixed this was to modify the asenv.conf file in the Appserver_Install dirrectory to point to the Java 1.5.0_06 installation and started the domain, now the form-based authentication is working as expected.
I guess my question now is does anyone know why I can't install the server with Java 1.5.0_06? But it looks like I need that version to actually run things correctly.

Configuration of LUN's to Sun Cluster

Hi,
I have a 2 node Sun Cluster (V3.2) running on 2xE2900, Solaris 10...
Basically, there are 3 installed Databases running on the development environment and I need to cluster all 3 in the Global Zone do some failovers and then engage Sun PS to come on site and configure the production cluster environment...
Usually I have already configured metasets or ZFS and then the DBA installs the DB while everything is nice and neat, my question however is what is the best way to cluster the LUN's when they already have data which I cannot (or would prefer not) to loose.
I believe the creation of LUN's in a metaset will destroy the data and obviously zfs pools will also destroy any data... hopefully this is a simple question from an SC novice :)
Thanks...

Thanks Tim, that answer the question... one more though :)
I was advised to install a single node cluster then add the 2nd node to the config later. Ive done this but when I try to do the add it seems I have a problem with the cluster interconnects and receive the messages:-
Adding cable to the cluster configuration ... failed
scrconf: Failed to add cluster transport cable - does not exist
scinstall: Failed to update cluster configuration ("-m endpoint=<server>:ce3,endpoint=switch1")
The heartbeats are ce3 and ce7 which I know are working ok, ive tried everything from the 1st node but when I enter:-
# scstat -W
Nothing is shown, although when I do a scconf -p I can see the node transport adapters ok... so how do I let the 2nd node access to the cluster interconnects, ive tried clsetup and adding the interconnects via option4 and I remember configuring them during installation...
Again any input would be greatly received...
Thanks...
Steve..

SAP 7.0 on SUN Cluster 3.2 (Solaris 10 / SPARC)

Dear All;
i'm installing a two nodes cluster (SUN Cluster 3.2 / Solaris 10 / SPARC), for a HA SAP 7.0 / Oracle 10g DataBase
SAP and Oracle softwares were successfully installed and i could successfully cluster the Oracle DB and it is tested and working fine.
for the SAP i did the following configurations
# clresource create -g sap-ci-res-grp -t SUNW.sap_ci_v2 -p SAPSID=PRD -p Ci_instance_id=01 -p Ci_services_string=SCS -p Ci_startup_script=startsap_01 -p Ci_shutdown_script=stopsap_01 -p resource_dependencies=sap-hastp-rs,ora-db-res sap-ci-scs-res
# clresource create -g sap-ci-res-grp -t SUNW.sap_ci_v2 -p SAPSID=PRD -p Ci_instance_id=00 -p Ci_services_string=ASCS -p Ci_startup_script=startsap_00 -p Ci_shutdown_script=stopsap_00 -p resource_dependencies=sap-hastp-rs,or-db-res sap-ci-Ascs-res
and when trying to bring the sap-ci-res-grp online # clresourcegroup online -M sap-ci-res-grp
it executes the startsap scripts successfully as following
Sun Microsystems Inc. SunOS 5.10 Generic January 2005
stty: : No such device or address
stty: : No such device or address
Starting SAP-Collector Daemon
11:04:57 04.06.2008 LOG: Effective User Id is root
Starting SAP-Collector Daemon
11:04:57 04.06.2008 LOG: Effective User Id is root
* This is Saposcol Version COLL 20.94 700 - V3.72 64Bit
* Usage: saposcol -l: Start OS Collector
* saposcol -k: Stop OS Collector
* saposcol -d: OS Collector Dialog Mode
* saposcol -s: OS Collector Status
* Starting collector (create new process)
* This is Saposcol Version COLL 20.94 700 - V3.72 64Bit
* Usage: saposcol -l: Start OS Collector
* saposcol -k: Stop OS Collector
* saposcol -d: OS Collector Dialog Mode
* saposcol -s: OS Collector Status
* Starting collector (create new process)
saposcol on host eccprd01 started
Starting SAP Instance ASCS00
Startup-Log is written to /export/home/prdadm/startsap_ASCS00.log
saposcol on host eccprd01 started
Running /usr/sap/PRD/SYS/exe/run/startj2eedb
Trying to start PRD database ...
Log file: /export/home/prdadm/startdb.log
Instance Service on host eccprd01 started
Jun 4 11:05:01 eccprd01 SAPPRD_00[26054]: Unable to open trace file sapstartsrv.log. (Error 11 Resource temporarily unavailable) [ntservsserver.cpp 1863]
/usr/sap/PRD/SYS/exe/run/startj2eedb completed successfully
Starting SAP Instance SCS01
Startup-Log is written to /export/home/prdadm/startsap_SCS01.log
Instance Service on host eccprd01 started
Jun 4 11:05:02 eccprd01 SAPPRD_01[26111]: Unable to open trace file sapstartsrv.log. (Error 11 Resource temporarily unavailable) [ntservsserver.cpp 1863]
Instance on host eccprd01 started
Instance on host eccprd01 started
and the it repeats the following warnings on the /var/adm/messages till it fails to the other node
Jun 4 12:26:22 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:25 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:25 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:28 eccprd01 last message repeated 1 time
Jun 4 12:26:28 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:31 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:31 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:34 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:34 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:37 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:37 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:40 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:40 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:43 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:43 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:46 eccprd01 last message repeated 1 time
Jun 4 12:26:46 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:49 eccprd01 last message repeated 1 time
Jun 4 12:26:49 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:52 eccprd01 last message repeated 1 time
Jun 4 12:26:52 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:55 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:55 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:26:58 eccprd01 last message repeated 1 time
Jun 4 12:26:58 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:01 eccprd01 last message repeated 1 time
Jun 4 12:27:01 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:04 eccprd01 last message repeated 1 time
Jun 4 12:27:04 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:07 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:07 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:10 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:10 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:13 eccprd01 last message repeated 1 time
Jun 4 12:27:13 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:16 eccprd01 last message repeated 1 time
Jun 4 12:27:16 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:19 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:19 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:22 eccprd01 last message repeated 1 time
Jun 4 12:27:22 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:25 eccprd01 last message repeated 1 time
Jun 4 12:27:25 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:28 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:28 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:31 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:31 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:34 eccprd01 last message repeated 1 time
Jun 4 12:27:34 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:37 eccprd01 last message repeated 1 time
Jun 4 12:27:37 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:40 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:40 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:43 eccprd01 last message repeated 1 time
Jun 4 12:27:43 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-scs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dispatcher to come up.
Jun 4 12:27:46 eccprd01 last message repeated 1 time
Jun 4 12:27:46 eccprd01 SC[SUNW.sap_ci_v2,sap-ci-res-grp,sap-ci-Ascs-res,sap_ci_svc_start]: [ID 183934 daemon.notice] Waiting for SAP Central Instance main dis
can anyone one help me if there is any error on configurations or what is the cause of this problem.....thanks in advance
ARSSES

Hi all.
I am having a similar issue with a Sun Cluster 3.2 and SAP 7.0
Scenrio:
Central Instance (not incluster) : Started on one node
Dialog Instance (not in cluster): Started on the other node
When I create the resource for SUNW.sap_as like
clrs create --g sap-rg -t SUNW.sap_as .....etc etc
in the /var/adm/messages I got lots of WAITING FOR DISPACHER TO COME UP....
Then after timeout it gives up.
Any clue? What does is try to connect or waiting for? I hve notest that it's something before the startup script....
TIA

Sun Cluster 3.1 64 bit support for Solaris 10

Hi:
I have some questions when migrate SC 3.1 from solaris 9 to solaris 10.
1) Does Clutster 3.1 for solaris 10 support 64 bit?
I have develop own resource type which is compiled with 64 bit mode, while cluster admin program is 32 bit based. E.g. /usr/cluster/bin/scrgadm
Will that cause any problem? For instance: 32 bit lib and 64 bit lib have the same name libscha.so will be loaded by 32 bit scrgadm and 64 bit my own developped resource type program.
2) Can I download a Cluster 3.1 install-pkg for solaris 10, 64 bit supported., which means all admin files like scrgadm are 64 bit based.
Or only ONE Cluster 3.1 version for solaris 10 is deliveried by SUN?
Thanks in advance!
BRs
//rdctahu

Hi,
Comments on your 2 questions:
1) Yes. IIRC, SC31 for S10 actually supports ONLY 64 bit. To be clear, this means
Solaris has to be booted in 64 bit mode, but 32 bit applications would run just
fine.
As for your RT being 64 bit, and scrgadm being 32 bit, no problem.
2) See (1). You are good.
Go for it.
HTH,
-ashu

Real Application Cluster on Sun Solaris 8 and Sun Cluster 3

Hello,
we want to install Oracle 9i Enterprise Edition in combination with Oracle Real Application Cluster-Option on 2 Nodes. Every node (12-CPU-SMP-Machine) should running Sun Solaris 8 and Sun Cluster 3 Service.
Does this configuration work with ORAC? I found nowhere informations about. Is there anything I have to pay special attention for during installation?
Thank you for helping and best regards from Berlin/Germany
Michael Wuttke

Forms and report services work fine on solaris 8.
My problem is on the client side.
I have to use solaris 8 with netscape like forms clients
and I wasn't able to make it work with java plugins.
Any solution?
Mauro

Upgrade from Solaris 8 SPARC with Sun cluster 3.1u3 to Solaris 10 SPARC

Dear All,
We are planning an upgrade of the OS from Solaris 8 SPARC to Solaris 10 SPARC on a two-node active-standby clustered system.
The current major software we have on the Solaris 8 system are:
1: Sun Cluster 3.1u3
2: Oracle 9i 9.2.0.8
3: Veritas File System Vxfs v4.0
4: Sun Solaris 8 2/04 SPARC
Any pointers as to what sequence and how the upgrade should be done?
Thanks in advance.
Regards,
Ray

yes I know it can be quite complicated and complex, but Sun provided us with a detailed documentation, at least in our case Solaris 9 to 10 it was very helpful.
You might get better help in the cluster forum http://forums.sun.com/forum.jspa?forumID=842
-- Nick

Upgrading Solaris OS (9 to 10) in sun cluster 3.1 environment

Hi all ,
I have to upgrade the solaris OS 9 to 10 in Sun cluster 3.1.
Sun Cluster 3.1
data service - Netbackup 5.1
Questions:
1 .Best ways to upgrade the Solaris 9 to 10 and the Problems while upgrading the OS?
2 .Sun Trunking support in Sun Cluster 3.1?
Regards
Ramana

Hi Ramana
We had used the live upgrade for upgrading Solaris 9 to 10 and its the best method for less downtime and risk but you have to follow the proper procedure as it is not the same for normal solaris. Live upgrade with sun cluster is different . you have to take into consideration about global devices and veritas volume manager. while creating new boot environment.
Thanks/Regards
Sadiq

Bizzare Disk reservation probelm with sun cluster 3.2 - solaris 10 X 4600

We have a 4 node X4600 sun cluster with shared AMS500 storage. There over 30 LUN's presented to the cluster.
When any of the two higher nodes ( ie node id 2 and node is 3 ) are booted, their keys are not added to 4 out of 30 LUNS. These 4 LUNs show up as drive type unknown in format. I've noticed that the only thing common with these LUN's is that their size is bigger than 1TB
To resolve this I simply scrub the keys, run sgdevs than they showup as normal in format and all nodes keys are present on the LUNS.
Has anybody come across this behaviour.
Commands used to resolve problem
1. check keys #/usr/cluster/lib/sc/scsi -c inkeys -d devicename
2. scrub keys #/usr/cluster/lib/sc/scsi -c scrub -d devicename
3. #sgdevs
4. check keys #/usr/cluster/lib/sc/scsi -c inkeys -d devicename
all node's keys are now present on the lun

Hi,
according to http://www.sun.com/software/cluster/osp/emc_clarion_interop.xml you can use both.
So at the end it all boils down to
- cost: Solaris multipathing is free, as it is bundled
- support: Sun can offer better support for the Sun software
You can try to browse this forum to see what others have experienced with Powerpath. From a pure "use as much integrated software as possible" I would go with the Solaris drivers.
Hartmut

Sun cluster patch for solaris 10 x86

I have Solaris 10 6/06 installed on x4100 box with 2 node clustering using Sun Cluster 3.1 8/05. I just want to know is there any latest patches available for the OS to prevent cluster related bugs. what are they? My kernel patch is 118855-19.
any inputs needed. let me know.

Well, I would run S10 updatemanager and get the latest patches that way.
Tim
---

Sun cluster 3.1 on Solaris 10 update1

Hi All,
Good day !!!
I am trying to build Sun Cluster 3.1 on Sun Solaris 10 update1 operating system.
I am using sun V240 servers. If i plumb bge1 and bge2 the second
and third interface and reboot the server system is not comming up.
it promts error saying "init" failed and it stops responding.
Also if i create /etc/defaultrouter file and put gateway system is not comming up.
Kindly let me know weather solaris 10 update1 is support for cluster or not.
Thanks,
nagaraju

Hi, I am not sure what your network setup looks like but I assume that you have configured your first port as the public network. You do not need to touch any other interface for the cluster setup manually. During the installation procedure you just give the names of your private network ports to the scinstall procedure. This will do all the setup for you.
The V240 is supported for SC3.1.
Regards
Hartmut

Recommendations for Multipathing software in Sun Cluster 3.2 + Solaris 10

Hi all, I'm in the process of building a 2-node cluster with the following specs:
2 x X4600
Solaris 10 x86
Sun Cluster 3.2
Shared storage provided by a EMC CX380 SAN
My question is this: what multipathing software should I use? The in-built Solaris 10 multipathing software or EMC's powerpath?
Thanks in advance,
Stewart

Hi,
according to http://www.sun.com/software/cluster/osp/emc_clarion_interop.xml you can use both.
So at the end it all boils down to
- cost: Solaris multipathing is free, as it is bundled
- support: Sun can offer better support for the Sun software
You can try to browse this forum to see what others have experienced with Powerpath. From a pure "use as much integrated software as possible" I would go with the Solaris drivers.
Hartmut

Need Sun WorkShop 6 update 2 for Solaris 8

Would it be possible to download an installation package for Sun WorkShop 6 update 2 for Solaris 8?
I have an old development project that I need to resurrect, and it requires this version of the Sun compiler.
Thanks,
-Ken Cooley

Object files and libraries created by WS6u2 can be linked into programs created by later versions of Sun Studio. The default template model changed in Studio 8, so you might need to add -instances=extern to CC command lines. Apart from that possibility, the only other issue I can think of would be invalid code accepted by WS6u2 that SS11 does not accept. I suggest you give Studio 11 a try, unless company policy forbids it.

Sun Cluster 3.0 update 1 on Solaris 8 - panics!

Similar Messages

Maybe you are looking for