Sun Cluster 3.1: Not same physical device (scdidadm -L)

Hi all,
I going to install Sun Cluster 3.1.
When verifying with the scdidadm -L, i got:
4 clustnode1:/dev/rdsk/c2t0d0 /dev/did/rdsk/d4
4 clustnode2:/dev/rdsk/c3t0d0 /dev/did/rdsk/d4
Seem that it not connected to the same physical device.
What do I have to check ?
Thanks,
Regards,
Aiggno

Some more information:
Node 1
0. c1t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e01070a271,0
1. c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e0106dd891,0
2. c2t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@0,0
3. c2t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@1,0
4. c2t2d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@2,0
5. c3t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@0,0
6. c3t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@1,0
7. c3t2d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@2,0
Node 2
0. c1t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e01070aad1,0
1. c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e01070aac1,0
2. c3t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@0,0
3. c3t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@1,0
4. c3t2d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@2/scsi@4/sd@2,0
5. c5t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@0,0
6. c5t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@1,0
7. c5t2d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
/pci@8,700000/pci@3/scsi@4/sd@2,0
Node 1 have c2, c3 and node 2 have c3, c5 ???

Similar Messages

  • Program working in virtual device, but not on physical device

    I made a program, pretty simple, actually, that simply consumes a web service here on my local network.  Pretty much all it does is try to authenticate.
    I had a problem with DNS before with the androids, so i replaced all of the domain names in the service xml files to IP addresses,  which still works virtually, but again, not on the physical device.
    Any ideas?

    Hello,
    Regarding the procmon capture;
    Yes, it is a lot of data. I would just start at the top and read my way down on both captures and then identify areas which they differ. Without understanding where the two captures differ, well - it would seem hard to understand where the difference in
    behaviour starts?
    Of course you can minimize the data by (this seems rather obvious, but lets re-iterate);
    1. Avoid all and any unnecessary background tasks
    2. Monitor normal system activity and exclude that
    3. Learn the application behavior and decide if you want to monitor only the application, or all system activity
    4. Understand the application
    As you have a working / non-working scenario - this seems like a perfect scenario of using ProcMon.
    Nicke Källén | The Knack| Twitter:
    @Znackattack

  • DS6 in a zone on a Sun Cluster

    I have a sun cluster that I am trying to configure and I don't know if I am trying to do something wrong, so I thought I would ask.
    I am using Sun Cluster 3.2 on a pair of Sun T2000s with a Fiber Channel disk array attached to both nodes. I have configured the disk array to have two file systems. One for each server. I have configured two resource groups in the global zone and setup a HAStoragePlus resource for each file system. I am successfully able to fail the file systems between the two nodes. On each of the file systems I have installed a zone. The zone is managed with the resource type provided by the SUNWsczone package to start and stop the zone. The resource is in the same resource group has the HAStoragePlus resource.
    At this point I have created resource group for the zone to manage the directory server. After creating the resource group I am trying to create a resource for the directory service HA service. When I use the clresource command it complains that the resource group does not contain a logical hostname. When using the services provided by the SUNWsczone package I created a logical hostname that is being assigned to the zone in question. Is there a way to install the Directory Server HA resource into the resource group for the zone?

    Philippe,
    DS 6 Sun Cluster Agent was not tested with SC 3.2 in Zones.
    Zone support came with SC 3.2, and DS 6 Cluster Agent was built with SC 3.1, tested with SC 3.1 and 3.2 in the Global zone.
    Regards,
    Ludovic.

  • Netegrity SiteMinder Agent on a Sun Cluster

    Salut!
    I have some doubts on how to run the Netegrity SiteMinder Agent on my Sun Cluster. Easiest solution would presumably be to run the Agent as a service on each of the physical cluster nodes.
    The application now can be accessed by the physical IP address/DNS-entry of the current cluster node, and the virtual one of the resource group. The users will access it by the virtual one. Now I somehow have to ensure that the agent watches the virtual one, too. Can this be configured? Takes DNS care of that (most likely not)?
    Or do I have to integrate the agent in the cluster software itself?
    Has anybody done that before?
    Thanks for your help,
    greetings,
    Martin

    Philippe,
    DS 6 Sun Cluster Agent was not tested with SC 3.2 in Zones.
    Zone support came with SC 3.2, and DS 6 Cluster Agent was built with SC 3.1, tested with SC 3.1 and 3.2 in the Global zone.
    Regards,
    Ludovic.

  • Sun cluster, 6140 and 'cross-connections'

    This was brought up in the storage forum by somebody else, but the responses never answered the original question:
    In the 6140 setup document located at http://docs.sun.com/source/819-7497-11/chapter3.html#50589714_93886 it shows two different ways to cable a host to a 6140 via a SAN switch. figure 3-3 and 3-4
    It states that the setup in 3-4 is not supported in a sun cluster environment.
    The problem is that given the acive/passive nature of the 6140, the setup shown in 3-4 is the obvious one to use since it prevents one from having to force all of the luns over in the event of an hba port or switch failure.
    To make life more interesting, the 6140 setup doc does not make not of what version of sun cluster it is not supported on. Or what the bugid is, or any informationto know if the restriction is still valid.
    So, does this restriction still exist? If so, for what version of sun cluster? What version of solaris?

    Thanks for the clarification.
    As an aside, it would be nice if in the future, the documentation could contain a bit more information than just a simple note saying 'this is not supported'. A reference to a bugid or info doc would go a long way in helping folks determine if the restriction is still valid.
    --john                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       

  • Oracle9i installation on Sun cluster not showing the cluster config screen

    Hi All,
    We are trying to install Oracle 9i RAC on a 2 node Sun cluster. The oracle installer never shows up the cluster configuration screen. However if we run the preInstall checker script from oracle (Installprecheck.sh) , it reports that it has indeed detected the cluster. Can anyone please help us out of this predicament.
    -Kishore

    Hi Kishore,
    I 'm assuming the following:
    . Sun Cluster 3.1 will be used to support Oracle 9i RAC
    . Oracle is being installed on a file system instead of raw devices
    To answer your question, a clustered file system must be present in order for Oracle 9i RAC Installer to recognize that a cluster exists before it displays the cluster configuration screen at the beginning of the installation.
    Prior to QFS 4.2, Sun did not support a clusteed file system. All Oracle RAC systems for Solaris were raw device based. You're in luck now because Sun has released Sun QFS 4.2 which support a clustered file system.

  • Sun Cluster and EMC AX150 does not work

    Hi All,
    I tried to setup a Sun Cluster 3.2 (2x T2000) with an EMC AX 150 Storage. the device paths are highly instable and breaking down time and again. Tried to install Powerpath software of EMC but this time the did-devices are not recognized by Sun Cluster.
    Any help will be appriciated.
    P.S: does anybody know whether a MSA 1000 will work with Sun Cluster 3.2.
    Regards

    Looking at the EMC link on http://www.sun.com/software/cluster/osp/ it doesn't look like these storage systems have been tested by EMC and so may or may not work.
    You could try using Sun's MPxIO rather than PowerPath. MPxIO is included in Solaris for free. Again, it may or may not work. You are unlikely to get support on either configuration until EMC has done the prerequisite engineering testing to resolve the sort of issues you are currently seeing.
    Regards,
    Tim
    ---

  • Can not log in another Blackberry ID in the same BB device

    Can not log in another Blackberry ID eventhough I have already sign out(and wipe out data automatically) previsous
    Blackberry ID from the same the device.
    Please someone kindly assist ASAP.
    PS. Do I need to deassociate both via device & email?

    kkawin45 wrote:
    Can not log in another Blackberry ID eventhough I have already sign out(and wipe out data automatically) previsous
    Blackberry ID from the same the device.
    Please someone kindly assist ASAP.
    PS. Do I need to deassociate both via device & email?
    Hello kkawin45
    Welcome to BlackBerry Support Forums
    You cannot use multiple BlackBerry ID on your BlackBerry 9900 at a same time ! On BlackBerry 7 devices BlackBerry ID is deep integrated with our device . If you want to use a new BlackBerry ID then perform a security wipe , while wiping be sure to Mark everything ( User Installed application  , Emails ) but after a full backup .
    Refer to this KB Article for help :
    KB26694 : How to change the BlackBerry ID on a BlackBerry PlayBook tablet or BlackBerry smartphone
    Click " Like " if you want to Thank someone.
    If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

  • I have multiple devices that have my iCloud E-mail, I want to disable the E-Mail on some of the devices but keep it on others, I do not have physical access to the ones I want to disable but I do have access to the devices I want to keep receiving mc

    I have multiple devices that have my iCloud E-mail, I want to disable the E-Mail on some of the devices but keep it on others, I do not have physical access to the ones I want to disable but I do have access to the devices I want to keep receiving mail, can I do this with a simple password reset or will that still leave all devices enabled?

    The simple way would be to uncheck 'Mail' in System Preferences (or Settings)>iCloud, but as you would need access to the devices in question to do that you will have to change your password, at http://appleid.apple.com. You will then need to sign out and back on all the devices you want to be able to receive mail, and it's important that you follow this procedure and note the warning:
    Firstly, if you have 'Find My iPhone/iPad/iMac' enabled on any of your devices, turn it off.
    Go to http://appleid.apple.com and click 'Manage your Apple ID'. Sign in with the current ID.
    Where it says 'Password & Security' and gives your current ID email address, click 'edit'.
    Enter your new password and click 'Save changes'.
    Now you will need to go to each of your devices and sign out in System Preferences (or Settings)>iCloud - 'Sign out' on a Mac, 'Delete this account' on an iOS device (this will not delete the account from the server).
    Then sign back in with your new ID. Your iCloud data will disappear from your devices when you sign out, but reappear when you sign back in.
    I re-iterate: before you start, turn off 'Find My Mac' (or whatever) or you will need the services of Support.
    The devices on which you have not changed the password will throw up continual error messages as they attempt to contact iCloud and fail.

  • HT4437 hi even when i connect my macbook and apple tv to the same wifi network i cant put on the air play mirroring option.my airplay mirroring option does not detect any device.what can i do for this?

    hi even when i connect my macbook and apple tv to the same wifi network i cant put on the air play mirroring option.my airplay mirroring option does not detect any device.what can i do for this?

    See
    http://support.apple.com/kb/TS4215

  • I phone 5c on the app store update part where it says updates , then purchased not on this device how do i clear it it wont let me delete the history of the apps i bouht on a different i phone but same log in details

    I phone 5c on the app store update part where it says updates , then purchased not on this device how do i clear it it wont let me delete the history of the apps i bouht on a different i phone but same log in details

    You can't delete your purchase history, you can only hide it (in iTunes on your computer).

  • 2 node Sun Cluster 3.2, resource groups not failing over.

    Hello,
    I am currently running two v490s connected to a 6540 Sun Storagetek array. After attempting to install the latest OS patches the cluster seems nearly destroyed. I backed out the patches and right now only one node can process the resource groups properly. The other node will appear to take over the Veritas disk groups but will not mount them automatically. I have been working on this for over a month and have learned alot and fixed alot of other issues that came up, but the cluster is just not working properly. Here is some output.
    bash-3.00# clresourcegroup switch -n coins01 DataWatch-rg
    clresourcegroup: (C776397) Request failed because node coins01 is not a potential primary for resource group DataWatch-rg. Ensure that when a zone is intended, it is explicitly specified by using the node:zonename format.
    bash-3.00# clresourcegroup switch -z zcoins01 -n coins01 DataWatch-rg
    clresourcegroup: (C298182) Cannot use node coins01:zcoins01 because it is not currently in the cluster membership.
    clresourcegroup: (C916474) Request failed because none of the specified nodes are usable.
    bash-3.00# clresource status
    === Cluster Resources ===
    Resource Name Node Name State Status Message
    ftp-rs coins01:zftp01 Offline Offline
    coins02:zftp01 Offline Offline - LogicalHostname offline.
    xprcoins coins01:zcoins01 Offline Offline
    coins02:zcoins01 Offline Offline - LogicalHostname offline.
    xprcoins-rs coins01:zcoins01 Offline Offline
    coins02:zcoins01 Offline Offline - LogicalHostname offline.
    DataWatch-hasp-rs coins01:zcoins01 Offline Offline
    coins02:zcoins01 Offline Offline
    BDSarchive-res coins01:zcoins01 Offline Offline
    coins02:zcoins01 Offline Offline
    I am really at a loss here. Any help appreciated.
    Thanks

    My advice is to open a service call, provided you have a service contract with Oracle. There is much more information required to understand that specific configuration and to analyse the various log files. This is beyond what can be done in this forum.
    From your description I can guess that you want to failover a resource group between non-global zones. And it looks like the zone coins01:zcoins01 is reported to not be in cluster membership.
    Obviously node coins01 needs to be a cluster member. If it is reported as online and has joined the cluster, then you need to verify if the zone zcoins01 is really properly up and running.
    Specifically you need to verify that it reached the multi-user milestone and all cluster related SMF services are running correctly (ie. verify "svcs -x" in the non-global zone).
    You mention Veritas diskgroups. Note that VxVM diskgroups are handled in the global cluster level (ie. in the global zone). The VxVM diskgroup is not imported for a non-global zone. However, with SUNW.HAStoragePlus you can ensure that file systems on top of VxVM diskgroups can be mounted into a non-global zone. But again, more information would be required to see how you configued things and why they don't work as you expect it.
    Regards
    Thorsten

  • I've had my iphone 5s since march 2014  and I've been using the same charger it came with. for the last two weeks ive been getting a message saying the accessory may not support the device. how is that possible?

    How come I keep getting a message saying that the accessory may not support the device?  I've been using the same charger that came in the box with the phone. Now it doesn't charge at all.

    Then take the cable, the plug and your iPhone to an Apple Store genius bar it is still  under the 12 month warranty

  • Sun Cluster & 6130/6140 thru switch with cross-connections not supported?

    Hi:
    I noticed that the 6140 does not support cross-connecting the 2 controllers to 2 switches for higher availability when using Sun Cluster:
    http://docs.sun.com/source/819-7497-10/chapter3.html
    Does anyone know why this restriction is there?
    Thanks!

    Since there was no real answer to the question in this forum, I cross posted this issue to the cluster forum.
    See http://forum.java.sun.com/thread.jspa?threadID=5261282&tstart=0 for the full thread.
    Basically, the restriction against cross-connections is no longer valid and the documentation should be updated to remove the note.
    This is all a good thing, because I had my 6140's wired into my sun cluster environment via the 'cross-connections' method diagramed in figure 3-4. :-)

  • I can download photos to my computer via my Ipod Touch but not a video of 833mb yet I can send it to my FB account on the same said device, does this make any sense?

    I can download photos to my computer via my Ipod Touch but not a video of 833mb yet I can send it to my FB account on the same said device, does this make any sense?

    See:
    iOS: Importing personal photos and videos from iOS devices to your computer
    Do y have XP? if so see that topic in the above link,
    Can you go to My Computer>iPod>DCIM folder and copy it from there?
    Windows XP can't import video files larger than 500 MB using Camera and Scanner Wizard. You can transfer these files from your device by selecting them in My Computer and dragging or copying the files to your computer's hard drive.

Maybe you are looking for