SUn CLuster 3.2 install - scinstall on x86 32 bit Solaris 5.10

Ok - I have 2 machines with 32-bit x86 SOlaris 5.10 - I installed the Sun Cluster 3.2 software but everytime I try scinstall it says rebooting other node and the other node never brings sun cluster up -
Questions:
1. The private interface does not come up on reboot - should it - and should I have an entry for cluster-priv1 in /etc/hosts
2. I know I am supposed to do a scvx -xv - I then try to enable the cluster service, but everything says disabled
I have tried this 5 times no luck - I have lots of cluster experience - and can get Oracle CRS working fine
Any thoughts

Yeahh, guys!!!
I was trying to establish a two-node cluster using VirtualBox + Solaris x86 + Sun Cluster 3.2. The node where I was running scinstall to configure my cluster environment was rebooting the other node in the end of the configuration process but it was hanging in the "Rebooting node01..." message just because it was not able to establish the cluster.
After see your comments, I changed Solaris x86 to Solaris Express Community Edition and Sun Cluster to Cluster Express and now everything is working fine!
Thanks!
Jansen Sena <[email protected]>

Similar Messages

LDOM SUN Cluster Interconnect failure

I am making a test SUN-Cluster on Solaris 10 in LDOM 1.3.
in my environment, i have T5120, i have setup two guest OS with some configurations, setup sun cluster software, when executed, scinstall, it failed.
node 2 come up, but node 1 throws following messgaes:
Boot device: /virtual-devices@100/channel-devices@200/disk@0:a File and args:
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Hostname: test1
Configuring devices.
Loading smf(5) service descriptions: 37/37
/usr/cluster/bin/scdidadm: Could not load DID instance list.
/usr/cluster/bin/scdidadm: Cannot open /etc/cluster/ccr/did_instances.
Booting as part of a cluster
NOTICE: CMM: Node test2 (nodeid = 1) with votecount = 1 added.
NOTICE: CMM: Node test1 (nodeid = 2) with votecount = 0 added.
NOTICE: clcomm: Adapter vnet2 constructed
NOTICE: clcomm: Adapter vnet1 constructed
NOTICE: CMM: Node test1: attempting to join cluster.
NOTICE: CMM: Cluster doesn't have operational quorum yet; waiting for quorum.
NOTICE: clcomm: Path test1:vnet1 - test2:vnet1 errors during initiation
NOTICE: clcomm: Path test1:vnet2 - test2:vnet2 errors during initiation
WARNING: Path test1:vnet1 - test2:vnet1 initiation encountered errors, errno = 62. Remote node may be down or unreachable through this path.
WARNING: Path test1:vnet2 - test2:vnet2 initiation encountered errors, errno = 62. Remote node may be down or unreachable through this path.
clcomm: Path test1:vnet2 - test2:vnet2 errors during initiation
CREATED VIRTUAL SWITCH AND VNETS ON PRIMARY DOMAIN LIKE:<>
532 ldm add-vsw mode=sc cluster-vsw0 primary
533 ldm add-vsw mode=sc cluster-vsw1 primary
535 ldm add-vnet vnet2 cluster-vsw0 test1
536 ldm add-vnet vnet3 cluster-vsw1 test1
540 ldm add-vnet vnet2 cluster-vsw0 test2
541 ldm add-vnet vnet3 cluster-vsw1 test2
Primary DOmain<>
bash-3.00# dladm show-dev
vsw0 link: up speed: 1000 Mbps duplex: full
vsw1 link: up speed: 0 Mbps duplex: unknown
vsw2 link: up speed: 0 Mbps duplex: unknown
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 link: down speed: 0 Mbps duplex: half
e1000g2 link: down speed: 0 Mbps duplex: half
e1000g3 link: up speed: 1000 Mbps duplex: full
bash-3.00# dladm show-link
vsw0 type: non-vlan mtu: 1500 device: vsw0
vsw1 type: non-vlan mtu: 1500 device: vsw1
vsw2 type: non-vlan mtu: 1500 device: vsw2
e1000g0 type: non-vlan mtu: 1500 device: e1000g0
e1000g1 type: non-vlan mtu: 1500 device: e1000g1
e1000g2 type: non-vlan mtu: 1500 device: e1000g2
e1000g3 type: non-vlan mtu: 1500 device: e1000g3
bash-3.00#
NOde1<>
-bash-3.00# dladm show-link
vnet0 type: non-vlan mtu: 1500 device: vnet0
vnet1 type: non-vlan mtu: 1500 device: vnet1
vnet2 type: non-vlan mtu: 1500 device: vnet2
-bash-3.00# dladm show-dev
vnet0 link: unknown speed: 0 Mbps duplex: unknown
vnet1 link: unknown speed: 0 Mbps duplex: unknown
vnet2 link: unknown speed: 0 Mbps duplex: unknown
-bash-3.00#
NODE2<>
-bash-3.00# dladm show-link
vnet0 type: non-vlan mtu: 1500 device: vnet0
vnet1 type: non-vlan mtu: 1500 device: vnet1
vnet2 type: non-vlan mtu: 1500 device: vnet2
-bash-3.00#
-bash-3.00#
-bash-3.00# dladm show-dev
vnet0 link: unknown speed: 0 Mbps duplex: unknown
vnet1 link: unknown speed: 0 Mbps duplex: unknown
vnet2 link: unknown speed: 0 Mbps duplex: unknown
-bash-3.00#
and this configuration i give while setting up scinstall
Cluster Transport Adapters and Cables <<<You must identify the two cluster transport adapters which attach
this node to the private cluster interconnect.
For node "test1",
What is the name of the first cluster transport adapter [vnet1]?
Will this be a dedicated cluster transport adapter (yes/no) [yes]?
All transport adapters support the "dlpi" transport type. Ethernet
and Infiniband adapters are supported only with the "dlpi" transport;
however, other adapter types may support other types of transport.
For node "test1",
Is "vnet1" an Ethernet adapter (yes/no) [yes]?
Is "vnet1" an Infiniband adapter (yes/no) [yes]? no
For node "test1",
What is the name of the second cluster transport adapter [vnet3]? vnet2
Will this be a dedicated cluster transport adapter (yes/no) [yes]?
For node "test1",
Name of the switch to which "vnet2" is connected [switch2]?
For node "test1",
Use the default port name for the "vnet2" connection (yes/no) [yes]?
For node "test2",
What is the name of the first cluster transport adapter [vnet1]?
Will this be a dedicated cluster transport adapter (yes/no) [yes]?
For node "test2",
Name of the switch to which "vnet1" is connected [switch1]?
For node "test2",
Use the default port name for the "vnet1" connection (yes/no) [yes]?
For node "test2",
What is the name of the second cluster transport adapter [vnet2]?
Will this be a dedicated cluster transport adapter (yes/no) [yes]?
For node "test2",
Name of the switch to which "vnet2" is connected [switch2]?
For node "test2",
Use the default port name for the "vnet2" connection (yes/no) [yes]?
i have setup the configurations like.
ldm list -l nodename
NODE1<>
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet1 primary-vsw0@primary 0 network@0 00:14:4f:f9:61:63 1 1500
vnet2 cluster-vsw0@primary 1 network@1 00:14:4f:f8:87:27 1 1500
vnet3 cluster-vsw1@primary 2 network@2 00:14:4f:f8:f0:db 1 1500
ldm list -l nodename
NODE2<>
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet1 primary-vsw0@primary 0 network@0 00:14:4f:f9:a1:68 1 1500
vnet2 cluster-vsw0@primary 1 network@1 00:14:4f:f9:3e:3d 1 1500
vnet3 cluster-vsw1@primary 2 network@2 00:14:4f:fb:03:83 1 1500
ldm list-services
VSW
NAME LDOM MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
primary-vsw0 primary 00:14:4f:f9:25:5e e1000g0 0 switch@0 1 1 1500 on
cluster-vsw0 primary 00:14:4f:fb:db:cb 1 switch@1 1 1 1500 sc on
cluster-vsw1 primary 00:14:4f:fa:c1:58 2 switch@2 1 1 1500 sc on
ldm list-bindings primary
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
primary-vsw0 00:14:4f:f9:25:5e e1000g0 0 switch@0 1 1 1500 on
PEER MAC PVID VID MTU LINKPROP INTERVNETLINK
vnet1@gitserver 00:14:4f:f8:c0:5f 1 1500
vnet1@racc2 00:14:4f:f8:2e:37 1 1500
vnet1@test1 00:14:4f:f9:61:63 1 1500
vnet1@test2 00:14:4f:f9:a1:68 1 1500
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
cluster-vsw0 00:14:4f:fb:db:cb 1 switch@1 1 1 1500 sc on
PEER MAC PVID VID MTU LINKPROP INTERVNETLINK
vnet2@test1 00:14:4f:f8:87:27 1 1500
vnet2@test2 00:14:4f:f9:3e:3d 1 1500
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE INTER-VNET-LINK
cluster-vsw1 00:14:4f:fa:c1:58 2 switch@2 1 1 1500 sc on
PEER MAC PVID VID MTU LINKPROP INTERVNETLINK
vnet3@test1 00:14:4f:f8:f0:db 1 1500
vnet3@test2 00:14:4f:fb:03:83 1 1500
Any Idea Team, i beleive the cluster interconnect adapters were not successfull.
I need any guidance/any clue, how to correct the private interconnect for clustering in two guest LDOMS.

You dont have to stick to default IP's or subnet . You can change to whatever IP's you need. Whatever subnet mask you need. Even change the private names.
You can do all this during install or even after install.
Read the cluster install doc at docs.sun.com

Can i install a mix of 32-bit and 64-bit package ? and they work together ?

Customer environment is Linux x86-64 having package pam-0.99.6.2-6.el5_4.1.x86_64 installed as per x86-64 server and application requirement.
i.e # rpm -qi pam-0.99.6.2-6.el5_4.1
Name : pam Relocations: (not relocatable)
Version : 0.99.6.2 Vendor: Oracle America
Release : 6.el5_4.1 Build Date: Thu 11 Mar 2010 02:58:52 AM MST
Install Date: Tue 27 Apr 2010 02:12:43 AM MST Build Host: ca-build9.us.oracle.com
Group : System Environment/Base Source RPM: pam-0.99.6.2-6.el5_4.1.src.rpm
Size : 2577739 License: GPL or BSD
Signature : DSA/SHA1, Thu 11 Mar 2010 02:59:17 AM MST, Key ID 66ced3de1e5e0159
URL : http://www.us.kernel.org/pub/linux/libs/pam/index.html
Summary : A security tool which provides authentication for applications
Description :
PAM (Pluggable Authentication Modules) is a system security tool that
allows system administrators to set authentication policy without
having to recompile programs that handle authentication.
Now customer is installing other oracle monitoring application which is looking/requesting for 32 bit version of pam-0.99.6.2.6.el5_4.1 (i386), i.e this library
Question:
So, is there any way we can install the 32 bit version of this ? While 64 bit is still there ?
Concern with installing the 32 bit library, is that something picks it up mistakenly when it expects the 64 bit version.
Edited by: sgaraga on Jun 8, 2012 4:39 PM

You can run 32-bit software under a x86-64 OS provided you install the necessary x86 (32-bit) libraries.
The x86_64 CPU is fully backwards compatible with Intel x86 16-bit and 32-bit code. Because the full x86 16-bit and 32-bit instruction sets remains implemented in hardware without any intervening emulation, existing x86 executables run with no compatibility or performance penalties (http://en.wikipedia.org/wiki/X86-64)
An application that is 32-bit or 64-bit will have to be linked or share the appropriate library. 32-bit and 64-bit libraries won't be confused because they use different names.

Sun Cluster Core Conflict - on SUN Java install

Hi
We had a prototype cluster that we were playing with over two nodes.
We decided to uninstall the cluster by putting node into single user mode and running scinstall -r.
Afterwards we found that the Java Availability Suite was a little messed up - maybe because the kernel/registry had not been updated - it though the cluster and agent software was uninstalled and would not let us re-install. All the executabvles from /etc/cluster/bin had been removed from the nodes.
So, On both nodes we ran the uninstall program from /var/sadm/prod/... and then selected cluster and agents to uninstall.
On the first node, this completely removed the sun cluster compoenets and then allowed us to re-install the cluster software successfully.
On the second node, for some reason, it has left behind the component "Sun Cluster Core", and will not allow us to remove it with the uninstall.
When we try to re-install we get the following:
"Conflict - incomplete version of Sun Cluster Core has been detected"
In then points us to the sun cluster upgrade guide on sun.com.
My question is - how do we 'clean up' this node and remove the sun cluster core so we can re-install the sun cluster software from scratch?
I don't quite understand how this has been left behind....
thanks in advance
S1black.

You can use prodreg directly to clean up when your de-install has gone bad.
Use:
# prodreg browse
to list the products. You may need to recurse down into the individual items. The use:
# prodreg unregister ...
to unregister and pkgrm to remove the packages manually.
That has worked for me in the past. Not sure if it is the 'official' way though!
Regards,
Tim
---

Errors after initial Sun Cluster install

- SunOS conch 5.10 Generic_118833-36 sun4u sparc SUNW,Sun-Fire-V210
- Sun Cluster 3.2
I've gone through the scinstall process using the standard answers to questions. The only exception is that when it came to quorum, I answered I would set it up later, as I want to try to the quorum server. There's no shared storage - I'm seeing if it's possible to create a cluster using IP based replication.
I'm getting these error messages every 30 seconds (looks like a result of:
# svcs lrc:/etc/rc3_d/S91initgchb_resd
STATE STIME FMRI
legacy_run 16:19:29 lrc:/etc/rc3_d/S91initgchb_resd
Feb 8 16:38:59 conch Cluster.GCHB_resd: Unable to open door descriptor /var/run/rgmd_receptionist_door
Feb 8 16:38:59 conch Cluster.GCHB_resd: GCHB system error: scha_cluster_open failed with 18
Feb 8 16:38:59 conch : Bad file number
Feb 8 16:39:29 conch Cluster.GCHB_resd: Unable to open door descriptor /var/run/rgmd_receptionist_door
Feb 8 16:39:29 conch Cluster.GCHB_resd: GCHB system error: scha_cluster_open failed with 18
Feb 8 16:39:29 conch : Bad file number
Feb 8 16:39:59 conch Cluster.GCHB_resd: Unable to open door descriptor /var/run/rgmd_receptionist_door
Feb 8 16:39:59 conch Cluster.GCHB_resd: GCHB system error: scha_cluster_open failed with 18
Feb 8 16:39:59 conch : Bad file number
Feb 8 16:40:29 conch Cluster.GCHB_resd: Unable to open door descriptor /var/run/rgmd_receptionist_door
Feb 8 16:40:29 conch Cluster.GCHB_resd: GCHB system error: scha_cluster_open failed with 18
Feb 8 16:40:29 conch : Bad file number
There's no file system errors, and I'm at a complete loss as to why there appears to be this problem. Can anyone offer any advice?
Cheers,
Iain

Hi,
there are 2 issues here.
1. THe error messages that you see. I get them on my freshly installed cluster as well. What did I do? I used the JES installer and installed SC3.2 and SCGeo 3.2 - to be configured later. Ithink that it should only install the packages but not configure any part of them. It seems that it does oitherwise. To me ghcb sound like global cluster heartbeat.. I'll follow up with the developers to get this clarified.
2. Replication within a cluster and no shared storage. THis has several aspects. I, too, see more and more customer demand to have this. If you get it to work let us know. I am not sure though, why you installed the SC Geo edition to achieve this, as I do not think it well help you here.
In any case I can only recommend to set up the quorum server before proceeding, otherwise your whole cluster will panic as soon as you do a single reboot. That is per design..
Regards
Hartmut

Jumpstart install of sun cluster 3.1

Hi,
I'm trying to use jumpstart to install a 2nodes cluster. Solaris9 installs but get problems when the cluster software begins to install. I get these error messages:
Performing setup for Sun Cluster autoinstall ... nfs mount: scadm: : RPC: Rpcbin
d failure - RPC: Success
nfs mount: retrying: /a/autoscinstalldir
nfs mount: scadm: : RPC: Rpcbind failure - RPC: Success
nfs mount: scadm: : RPC: Rpcbind failure - RPC: Success
nfs mount: scadm: : RPC: Rpcbind failure - RPC: Success
nfs mount: scadm: : RPC: Rpcbind failure - RPC: Success
n
It does not install further. Could somebody give some suggestions?
thank you, pcurran

Hi All,
I have decided to first install sun cluster 3.1(trail version) manually:
1) installed sun_web_console. Installation completed successfully but got this statement at the end:
"Server not started, No management application registed"
2) Went ahead and to run "scinstall" but got this error:
** Installing SunCluster 3.1 framework **
SUNWscr.....failed
scinstall: Installation of "SUNWscr" failed
Below is the "log file":
** Installing SunCluster 3.1 framework **
SUNWscr
pkgadd -S -d /cdrom/hotburn_oct24_05/suncluster3.1/Solaris_sparc/Product/sun_clu
ster/Solaris_9/Packages -n -a /var/cluster/run/scinstall/scinstall.admin.11374
SUNWscrfailed
pkgadd: ERROR: cppath(): unable to stat </cdrom/hotburn_oct24_05/suncluster3.1/S
olaris_sparc/Product/sun_cluster/Solaris_9/Packages/SUNWscr/reloc/etc/cluster/cc
r/rgm_rt_SUNW.LogicalHostname:2>
pkgadd: ERROR: cppath(): unable to stat </cdrom/hotburn_oct24_05/suncluster3.1/S
olaris_sparc/Product/sun_cluster/Solaris_9/Packages/SUNWscr/reloc/etc/cluster/cc
r/rgm_rt_SUNW.SharedAddress:2>
ERROR: attribute verification of </etc/cluster/ccr/rgm_rt_SUNW.LogicalHostname:2
failedERROR: attribute verification of </etc/cluster/ccr/rgm_rt_SUNW.SharedAddress:2>
failed
pathname does not exist
Reboot client to install driver.
Installation of <SUNWscr> partially failed.
scinstall: Installation of "SUNWscr" failed
scinstall: scinstall did NOT complete successfully!
Could someone please give some direction?
thank you, pcurran

Sun cluster patch for solaris 10 x86

I have Solaris 10 6/06 installed on x4100 box with 2 node clustering using Sun Cluster 3.1 8/05. I just want to know is there any latest patches available for the OS to prevent cluster related bugs. what are they? My kernel patch is 118855-19.
any inputs needed. let me know.

Well, I would run S10 updatemanager and get the latest patches that way.
Tim
---

Install of HA MaxDB in a Sun Cluster 3.2 environment

Hi. I am installing SAP Content Server using MaxDB in a Sun Cluster 3.2 environment. According to the SUN doc, I must install the X_server as a scalable resource/service. For a scalable resource, I have to make the disk available on both nodes of the cluster. I need to identify what are all the executables for the x_server so that I can make those mount points a NFS share. From looking at the content of previous non-clustered installs, I am thinking I need to make the directories /sapdb/data and /sapdb/program NFS to isolate the x_server components. Does anyone have experience with this setup ? I've placed a log with OSS but wanted to see if anyone else in the forum has done this before. Thanks for any input.

Hello Dan,
Please review the SAP Note No. 803452.
X_server tool is the the part of the indepentent database software installation <independent_program_path>. Using NFS you could set up the <independent_program_path> and <independent_data_path> directories as share directories.
Thank you and best regards, Natalia Khlopina

How to install a SUN cluster in a non-global zone?

How do I install a SUN cluster in a non-global zone? If it is the same as installing SUN Cluster in the global zone, then how do I access the cdrom from a non-global zone to the global zone?
Please point me to some docs or urls if there are any. Thanks in advance!

You don't really install the cluster software on zones. You have to set up a zone cluster once you have configured the Global Zone cluster (or in other words, clustered the physical systems + OS).
http://blogs.sun.com/SC/entry/zone_clusters

Can I install Sun Cluster on LDOM guest domain. Is Oracle RAC a supported c

Hello,
Can I install Sun Cluster on LDOM guest domains. Is Oracle RAC on LDOM guest domains of 2 physical servers a supported configuration from oracle?
Many thanks in advance
Ushas Symon

Hello,
The motive behind using LDOm Guest domains as RAC node is to have a better control of the resource allocation, since i will be having more than one guest domains which should perform different functions. The customer wants to have ORACLE RAC alone (without sun cluster).
I will have two T5120's and one 2540 shared storage.
My plan of configuration is to have
Control&IO Domain with 8VCPU, 6GB mem
one LDOM guest domain on each physical machine with 8 VCPU's, 8GB of memory, shared n/w and disks participating as RAC node's. (Don't know yet if i will use solaris cluster or not)
one guest domain on each physical machine with 12 VCPU's, 14GB of memory, shared n/w and disks participating as BEA weblogic cluster nodes (not on solaris cluster)
One guest domain on each physical machine with 4 VCPU's, 4GB of memory,shared n/w and disks participating as apache web cluster (on solaris cluster)
Now, My question is, is it a supported configuration to have guest domains as Oracle RAC participants for 11gR2 (either with or without solaris cluster).
If I need to configure RAC nodes on solaris cluster, is it possible to have two independent clusters on LDOM , one 2 node cluster for RAC and another 2 node cluster for apache web?
Kindly advise
Many thanks in advance
Ushas Symon

Installing sun cluster on system based on SUNWcrnet

Hi,
I'm planning to testdrive the sun cluster software. All our systems do run the SUNWcrnet install cluster plus additionally required packages. I read that for sun cluster 3.1 at least SUNWCuser is necessary. Did anybody succeed in running sun cluster software on a system based on SUNWcrnet? If yes which are the additionally needed packages?
Thanks,
mark

I wouldn't bother. You will need to install way too many packages. SUNWcrnet by default does not even give you the showrev command. I rather install everything and then disable what I don't need.

Installing oracle 10g RAC on sun cluster

Hi
we r implementing new setup with fallowing configuration
OS: sun solaris 10 on sunfire v890 servers 2 node rac
4 processor server sun SPARC 64 bit
SUN cluster
oracle :10.2.0.3
please send me related documents for installing CRS and RdBMS and
Message was edited by:
Adithya
Message was edited by:
Adithya

Installation Guide for Solaris Cluster 3.2 Software and Oracle 10g Release 2 Real Application Clusters

Encountered ora-29701 during Sun Cluster for Oracle RAC 9.2.0.7 startup (UR

Hi all,
Need some help from all out there
In our Sun Cluster 3.1 Data Service for Oracle RAC 9.2.0.7 (Solaris 9) configuration, my team had encountered
ora-29701 *Unable to connect to Cluster Manager*
during the startup of the Oracle RAC database instances on the Oracle RAC Server resources.
We tried the attached workaround by Oracle. This workaround works well for the 1^st time but it doesnt work anymore when the server is rebooted.
Kindly help me to check whether anyone encounter the same problem as the above and able to resolve. Thanks.
Bug No. 4262155
Filed 25-MAR-2005 Updated 11-APR-2005
Product Oracle Server - Enterprise Edition Product Version 9.2.0.6.0
Platform Linux x86
Platform Version 2.4.21-9.0.1
Database Version 9.2.0.6.0
Affects Platforms Port-Specific
Severity Severe Loss of Service
Status Not a Bug. To Filer
Base Bug N/A
Fixed in Product Version No Data
Problem statement:
ORA-29701 DURING DATABASE CREATION AFTER APPLYING 9.2.0.6 PATCHSET
*** 03/25/05 07:32 am ***
TAR:
PROBLEM:
Customer applied 9.2.0.6 patchset over 9.2.0.4 patchset.
While creating the database, customer receives following error:
ORA-29701: unable to connect to Cluster Manager
However, if customer goes from 9.2.0.4 -> 9.2.0.5 -> 9.2.0.6, the problem does not occur.
DIAGNOSTIC ANALYSIS:
It seems that the problem is with libskgxn9.so shared library.
For 9.2.0.4 -> 9.2.0.5 -> 9.2.0.6, the install log shows the following:
installActions2005-03-22_03-44-42PM.log:,
[libskgxn9.so->%ORACLE_HOME%/lib/libskgxn9.so 7933 plats=1=>[46]langs=1=> en,fr,ar,bn,pt_BR,bg,fr_CA,ca,hr,cs,da,nl,ar_EG,en_GB,et,fi,de,el,iw,hu,is,in, it,ja,ko,es,lv,lt,ms,es_MX,no,pl,pt,ro,ru,zh_CN,sk,sl,es_ES,sv,th,zh_TW, tr,uk,vi]]
installActions2005-03-22_04-13-03PM.log:, [libcmdll.so ->%ORACLE_HOME%/lib/libskgxn9.so 64274 plats=1=>[46] langs=-554696704=>[en]]
For 9.2.0.4 -> 9.2.0.6, install log shows:
installActions2005-03-22_04-13-03PM.log:, [libcmdll.so ->%ORACLE_HOME%/lib/libskgxn9.so 64274 plats=1=>[46] langs=-554696704=>[en]] does not exist.
This means that while patching from 9.2.0.4 -> 9.2.0.5, Installer copies the libcmdll.so library into libskgxn9.so, while patching from 9.2.0.4 -> 9.2.0.6 does not.
ORACM is located in /app/oracle/ORACM which is different than ORACLE_HOME in customer's environment.
WORKAROUND:
Customer is using the following workaround:
cd $ORACLE_HOME/rdbms/lib make -f ins_rdbms.mk rac_on ioracle ipc_udp
RELATED BUGS:
Bug 4169291

Check if following MOS note helps.
Series of ORA-7445 Errors After Applying 9.2.0.7.0 Patchset to 9.2.0.6.0 Database (Doc ID 373375.1)

Didadm: unable to determine hostname. error on Sun cluster 4.0 - Solaris11

Trying to install Sun Cluster 4.0 on Sun Solaris 11 (x86-64).
iscs sharedi Quorum Disk are available in /dev/rdsk/ .. ran
devfsadm
cldevice populate
But don't see DID devices getting populated in /dev/did.
Also when scdidadm -L is issued getting the following error. Has any seen the same error ??
- didadm: unable to determine hostname.
Found in cluster 3.2 there was a Bug 6380956: didadm should exit with error message if it cannot determine the hostname
The sun cluster command didadm, didadm -l in particular, requires the hostname to function correctly. It uses the standard C library function gethostname to achieve this.
Early in the cluster boot, prior to the service svc:/system/identity:node coming online, gethostname() returns an empty string. This breaks didadm.
Can anyone point me in the right direction to get past this issue with shared quorum disk DID.

Let's step back a bit. First, what hardware are you installing on? Is it a supported platform or is it some guest VM? (That might contribute to the problems).
Next, after you installed Solaris 11, did the system boot cleanly and all the services come up? (svcs -x). If it did boot cleanly, what did 'uname -n' return? Do commands like 'getent hosts <your_hostname>' work? If there are problems here, Solaris Cluster won't be able to get round them.
If the Solaris install was clean, what were the results of the above host name commands after OSC was installed? Do the hostnames still resolve? If not, you need to look at why that is happening first.
Regards,
Tim
---

Invalid node name in Sun Cluster 3.1 installation

Dear all,
I need your advice in Sun Cluster 3.1 8/05 installation.
My colleague was installing Sun Cluster 3.1 8/05 on 2 servers Sun Netra 440 that given hostname 01-in-01 and 01-in-02. But when he want to configuring the cluster, the problem occured.
The error message is:
running scinstall: invalid node name
And when we changed the host name to in-01 and in-02, the cluster can be configured well.
Why did this problem happened?
Is it related with the given hostname that using numeric in the beginning? If yes, can you give the documentation that state about that?
Or maybe you have another explanation?
Thank you for your help.
regards,
Henry

A bug is being logged against this. (though obviously you could manually fix the shell script yourself if you were in a hurry).
The problem partly stems from the restriction on hostnames being relaxed by RFC 1123 which relaxed RFC 952's limitation of the first character to only alpha characters.). See man hosts for more info. I guess our code didn't catch up :-)
Tim
---

SUn CLuster 3.2 install - scinstall on x86 32 bit Solaris 5.10

Similar Messages

Maybe you are looking for