Sun e3000 / anysystems / sun os 10 / vga monitor

Hello,
i have a couple of questions,
the first does anybody know www.anysystem.com ?
They have a lot of suns there and not fore much money.
we want to buy an e 3000 is it possible to install there an sun os 10?
and the last question is it possible to use an vga lcd on an e3000?
thanks and sorry for my bad english

Do you perhaps actually have a Netra T1-105 system?
http://www.google.com/search?hl=en&q=sparc+fj1a&btnG=Google+Search
Then you do not attach a monitor.
There are no keyboard/mouse connectors.
Such systems are expecting you to administer them through a command line interface.
You connect another system through to the LOM port, else you connect through the TTYa (first) serial port.
Here's the T105 resource page in the Sun System Handbook:
http://sunsolve.sun.com/handbook_pub/Systems/Netra_t1_105/Netra_t1_105.html
Review its system documentation.

Similar Messages

  • SUN AI24PO 24" LCD Monitor C-Viedo / S-Video Problem... No Image

    We have few SUN AI24PO 24" LCD Monitors that are hooked up to Blade2000 and Blade2500 systems. These monitors have 1-Digital/DVI, 1-Analog/VGA, 1-S-Video, 1-C-Video inputs. The Digital and Analog inputs work fine but I cannot display anything that I feed to the S or C video inputs.
    When we connect a (inspection/security) camera signal to the C-video or S-video input on these monitors, we cannot get an image. The Screen stays blue. Once or twice the image from the camera flashes and then disappears. For the image to flash again, I need to disconnect the c-video connector and wait for more than 30mins and reconnect.
    I have verified the video signal and all my cabling on some of the newer 24' monitors and they all work fine.
    It seems some of the earlier monitors have a problems with the S-video and C-video inputs.
    Does anybody have see this problem on thier 24" SUN LCDs. Is there a fix.
    Any suggestions welcome.
    Thanks
    Surendra
    [email protected]

    My post has started a more extensive discussion on this problem at an Ars Technica forum:
    <http://episteme.arstechnica.com/groupee/forums?a=tpc&s=50009562&f=67909965&m=41 90936913&r=796009877731#796009877731>
    It appears that the problem may be inherent in all PVA-based LCD's, which include the Dell 2405FPW. It's not noticeable by everyone but so far everyone I've seen who's taken the time to run an objective test has uncovered the lag. If you can run the test, please do! (See earlier in this thread, or see the Ars Technica thread for a better test involving a stopwatch program run on two monitors).
    The good news is Apple's 23" Cinema Display is based on a SIPS LCD panel (as is a similar HP display, and I think a Sony display), and these don't suffer from the lag.
    Scott

  • External VGA monitor

    I've just brought the laptop and gone through the update saga, everything is working but one thing, the external VGA monitor is only ever accepted as being 1280x1024 despite it being 1600x1200 native.
    I have tried everything I can think of, uninstalling and reinstalling the Intel and Nvidia drivers (I'm really not sure which one is driving the VGA despite setting the laptop to always use the NVidia card), and editing the EDID for the monitor to try and force the graphics card to output 1600x1200.  My old laptop connected to it fine, and I've tested it with other equipment which also works fine.
    Has anyone else come across this issue?  The monitor is a Sun 22" CRT, its actually a rebadged Sony and goes under the driver name GDM-5510.
    Not sure here if I have faulty hardware as the notebook is brand new (7 days old), so wondering if sending it back is the best option (I guess since I've opened all the packaging the 7 day distance seller regulations are not an option?).
    Any advice appreciated.

    Yes, you are right, I did not tested it with another cable yet, and its a cheap VGA one, but it does not do this on on a very cheap budget laptop. Maybe the VGA port on the Thinkpad is very sensitive. Its running on 60 Hertz. I only have 50 and 60 to choose. And I always run on the highest.

  • Ultra 10 with Creator 3D and VGA monitor

    On the back of my Ultra 10 there are two connectors for monitors: one is the usual VGA connector and appears to be connected to the motherboard, the other is the traditional 13W3 Sun connector, apparently located on a Creator 3D card that came with the system.
    I have a Sun monitor, and I can use it with the Ultra 10 using the 13W3 connector; unfortunately, however, it is quite old and would like to connect the box to a newer monitor. So I tried to simply unplug the Sun monitor and plug in a VGA one, but nothing happened. Uhm, what am I forgetting to do?
    Incidentally, another silly question: supposing I do manage to connect a VGA monitor, what device will generate the display? The Creator 3D (that does NOT have a VGA connector) or the onboard device, whatever that is (since the VGA socket is connected to the motherboard, apparently). This could be relevant for the speed of graphics rendering, I suppose.

    This topic seems to re-appear every so often.
    <img src="images/smiley_icons/icon_cool.gif" border=0 alt="Cool">
    The UPA framebuffer will be more capable that the onboard ATI Rage chipset,
    which only has 4mb of video RAM and you will not get 24bit color if you set its resolution higher than 1152x900.
    You could also consider reconfiguring the system to run dual monitors.
    Search these hardware forums, keyword "xservers" (plural)
    I just saw about 35 hits.
    Then when you're ready, review the complete contents of the following file (case sensitive):
    <b>/usr/dt/config/Xservers</b>
    Depending on how you customize that file, you choose which monitor is console and which is the 'other one' ; you decide which is the left output and which is the right-hand screen; you could even run the output in a monitor spanning single GUI mode, although with disparate monitor models and different framebuffer chipsets, that may not be pleasing to the eye.
    ( see the man page for Xinerama )
    If I recall correctly, you can also find the user profile for a contributor named <u>ultraspec</u> and glance through a few of their postings, where they mention a DB13W3 to HD15 adapter cable.
    Edit: Oh, until such time as you do invoke the Xservers file within Solaris, I think the onboard circuit is disabled so long as the Creator card is physically inside. Remove the Creator card and the onboard is spontaneously your graphics output.

  • Display for a SUNFire V880 flickers with a VGA monitor

    Hi,
    I have a SunFire V880 which has been connected to a rack-mounted HP VGA monitor via an Avocent KVM for some years now.
    Recently, I found the display for server flickers non-stop, making it impossible to view.
    I have tried connecting it to other VGA monitors with the same results.
    Only when I connect it to a SUN monitor, did it display just fine.
    Could anyone advice on how I can get it to display on a VGA monitor again?
    Many Thanks!
    Edited by: Sheewah on Apr 9, 2008 2:38 AM

    Ok, I'll bite ...
    You provided no useful information as to the actual configuration,
    It would have helped to mention whether the monitor was in the same rack as the V880.
    (that would inform us as to length of cabling)
    It would have helped to note which frame buffer was in the computer.
    (that informs us of its capabilities)
    It would have helped to describe the current video settings.
    but ...
    Does the original display work if you eliminate the KVM from the lash-up
    and directly attach the screen to the V880?
    If yes, then the KVM is the root cause.
    If no, then find the refresh rate settings of the current output signal
    and change them to be compatible to whatever those non-Sun monitors need.

  • How to get two vga monitors on a mac mini 2012

    Hi Guys,
    please forgive any ignorance that follows. I am a new convert from a PC and have bought a Mac Mini 2012. I want to be able to use a monitor that I can see my music programme but run a second monitor that will allow me to display visuals from a VJ programme. Here is my journey.
    I bought the mac mini and the thunderbolt to vga adapter. Generic VGA monitor - worked a treat. I then wanted to run a second generic vga monitor form the hdmi port. After a lot research I chose an adapter for £15 that one of the reviews said worked perfectly for a mac mini and VGA. Bought it form Amazon. Didn't work - no signal etc - refund. Then I thought I would buy a monitor / DVD with a HDMI cable and do hdmi to hdmi and use that as the music monitor and use the thunderbolt port for the projector and VJ programme. Bought one from Asda. Plugged in great picture etc worked a treat but got a ground hum from new HDMI monitor. More research and realised that ground hum was a nightmare. HDMI monitor back and refund.
    It is doing my head in.
    I will be a happier man if someone could say that they have a mac mini 2012 and they bought this HDMI VGA converter and use a generic vga monitor and it works a treat. There is only so much stuff I can return before my lick runs out.
    I don't think I'm asking for much.
    Any help would be gratefully received.
    Cheers Pete

    Sorry, but I can not safely suggest a digital HDMI to analog VGA converter or if any would even work with the Mac Mini because I do not have and have not personally tested any.
    I can only suggest that instead of dropping more money into adapters or an HDMI to VGA converter, that perhaps' you should consider replacing one if not both with a more modern digital monitor that support either HDMI and/or DVI.

  • How to connect VGA Monitor via Thunderbolt Display

    I've been using my Macbook Air mid 2013 with a Samsung monitor connected via the Mini Display Port to VGA adapter. I've now bought a 27" Thunderbolt display, which I've connect to my Mac, and assumed I could now daisy chain my samsung monitor into the Thunderbolt port in the back of the monitor. This isn't working.
    Is this expected behaviour? Some people have said online that it will work if there's some other Thunderbolt peripheral between the Thunbolt Display and the VGA adapter, but I don't know what kind of peripheral they mean.
    Apple support says that my model Macbook air can power two external displays.
    How can I get this to work?
    Thank you

    I want to know if I can connect a vga monitor to the quad by simply getting a vga to dvi adaptor.
    Yes, you can.
    (50389)

  • Can I use a Mac mini with a VGA monitor?

    The Mac mini web page lists an Apple Mini DisplayPort to VGA Adapter as an accessory, but the Mac mini doesn't appear to have a Mini DisplayPort.
    The Mac mini also has an HDMI to DVI Adapter included, but would this allow a VGA monitor to be connected via an additional DVI to VGA cable? ie. can the HDMI port provide an analogue signal that a VGA monitor can receive?

    Some Mac Minis do have mini-DisplayPorts.  In these two it is between the HDMI and the USB ports:
    (yes Thunderbolt should accept mini-Displayport).
    In this one it is between the Mini-DVI and the USB ports:
    Only the oldest Intel models would you need a different adapter to VGA
    Those you would need a DVI to VGA adapter from Apple such as this one.  Note, DVI to VGA is converting digital to analog, and not very useful, unless your TV has neither DVI nor HDMI.  DVI is much better converted up to HDMI.  And the audio would have to come in separately.  So depending on your display model and make, you may be asking for the wrong adapter.  VGA is fine if all you are going to do is view DVDs on an old TV.  But if you want the ability to use the Dock, menubar, etc..., it is good to have a 1080p TV with built-in HDMI or better.

  • No signal to VGA monitor using Mac mini display to VGA adaptor and first time boot Mac mini

    Just unpacked Mac mini and powered up using Mac mini to VGA display adaptor and VGA monitor. There is no signal to the monitor ( power is on).
    How to see the display?

    [    13.093] (==) No Layout section.  Using the first Screen section.
    [    13.093] (==) No screen section available. Using defaults.
    [    13.093] (**) |-->Screen "Default Screen Section" (0)
    [    13.093] (**) |   |-->Monitor "<default monitor>"
    [    13.093] (==) No monitor specified for screen "Default Screen Section".
            Using a default monitor configuration.
    First step would be to create the necessary entries (easier to make a complete xorg.conf versus xorg.conf.d/##-whatever.conf).
    All Desktop Environments / Window Managers rely on X.  Man pages are helpful, possibly some headaches ahead as I fought a dual-monitor display this way.
    I currently run a xrandr script to switch displays on my hp pavilion: https://wiki.archlinux.org/index.php/Xrandr#Scripts
    Check it out.

  • Don't setup an XServe with a DVI monitor if you intend to use a VGA monitor

    Hi Forum Folks.
    A bit of a "gotcha" to warn others about, with XServes, and VGA vs DVI monitors.
    We Recently re-setup (erase + install a fresh OS) on a 2008 XServe Xeon, with a DVI (Digital) monitor connected. All worked fine, and we went to move the server into the production environment.
    However, when we moved + plugged the XServe into it's new home (a rack), it would not boot (flashing question mark).
    Moving the Xserve out of the rack, and back to it's work-bench setup, made it work again.
    We traced the problem to the monitor we used... If we hooked up a digital (DVI) monitor, the XServe worked fine (with the mini DVI to DVI connector). If we hooked up a VGA monitor (with a mini DVI to VGA connector) that's when the XServe wouldn't boot. We tried a variety of common techniques to solve the problem, including resetting various settings, re-installing Mac OS X 10.5.6 Server over the top etc.
    The solution:
    (Although I'm sure there are simpler solutions):
    We setup the server again (from scratch) using the VGA monitor combination from the very start of the setup, and all worked fine (on VGA or DVI monitors). The server is happily in production now, with it's VGA output.
    So the lesson here: Always set up your XServe using a VGA-based monitor in the first instance.
    Hope this helps someone else.
    Cheers,
    Derek

    So the lesson here: Always set up your XServe using a VGA-based monitor in the first instance.
    ... or don't use a monitor at all
    I don't think I've ever used a monitor when setting up a server - maybe used a KVM if I've re-installed or upgraded the OS, but for the main part every install I do is run remotely.
    Still it's good to know, especially since it defies logic.

  • HT3382 I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter.  How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

    I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter.  How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

    Hi alangium,
    Welcome to the Support Communities!
    Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
    OS X Mavericks: Reset your computer’s PRAM
    http://support.apple.com/kb/ph14222
    This article may provide some information about your Mini DisplayPort to AVI adapter.  Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
    Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
    http://support.apple.com/kb/HT3382
    18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
    The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573#5
    How can I detect displays?
    If the detect displays option is not available, hold down the Option key while you are in the Display pane.
    How do I select additional resolutions on my display?
    You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
    To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
    I hope this information helps ....
    - Judy

  • Can I use the Apple ADC to DVI adapter with a VGA monitor?

    Hey everybody,
    I have a quick question. I work on computers fr friends and family as a hobby. I have an ADC monitor and need ot be able to hook up computers with a VGA port on them to it. Can I use the Apple ADC to DVI adapter along with an Apple DVI to VGA adapter to successfully connect VGA computers to my ADC display? I was assuming this would work and ordered both adapters but now I have made myself nervous about weather or not this will actually work. Has anybody out there successfully done this? Thanks for your help in advance everybody.

    You can't run an ADC display with a VGA computer without a converter. Adapters won't do it.
    a VGA to ADC converter will drive the ADC display directly
    <http://www.gefen.com/kvm/product.jsp?prod_id=1301>
    If you have the Apple DVI to ADC adapter
    <http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=18 72D402&nplm=M8661LL/B>
    you could use it with a VGA to DVI converter
    <http://www.gefen.com/kvm/product.jsp?prod_id=1310>
    It might be cheaper to get DVI graphics boards for the computers and use the Apple DVI to ADC adapter.
    <http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=18 72D402&nplm=M8661LL/B>
    Your title says "Can I use the Apple ADC to DVI adapter with a VGA monitor?". If you want to connect a VGA monitor to a computer's ADC port you need the ADC to VGA adapter
    <http://www.gefen.com/kvm/product.jsp?prod_id=1299> You can't use an ADC to DVI adapter followed by a DVI to VGA adapter, because the ADC to DVI adapter doesn't pass the analog video signals needed for VGA.

  • VGA monitor and a 2010 Mac Mini - HELP PLEASE!

    I just upgraded from the early 2009 model where all you needed was a VGA to mini DVI adapter. With this 2010 model, Im not sure if thats possible (for cheap anyway). I have a VGA monitor and all I want to do is hook it up to the new mac mini ...but how? I've heard that because VGA is analog and HDMI is digital that it cannot be done for under $100 ..is this so? why oh why couldnt apple have stuck with mini dvi. Please someone advise how to do this ..or am I forced to buy a new monitor with DVI/Mini DVI/HDMI connections

    Forget the HDMI port. There's the Mini DisplayPort available, and all it takes is the right adapter:
    http://store.apple.com/us/product/MB572Z/A
    That should solve your problem.

  • How do you plug a VGA monitor to a Mac mini (mid 2011)

    I used my older Mac mini (mid 2007)  with a VGA LCD monitor through an "DVI to VGA" adapter with no problems.
    However, this older adapter does not fit in the "HDMI to DVI Adapter" supplied with my new Mac mini (mid 2011).
    There are no receptacles (holes) in the "HDMI to DVI adapter" for the four pins located around the flat tab on one hand of the older adapter .
    Any suggestion on how to plug a LCD VGA monitor to a mid 2011 Mac mini?
    I know there is a Thunderbolt port and a HDMI port,
    but being able to use an inexpensive VGA monitor for set-up and periodic maintenance,
    without having to fire up a huge plasma screen each time, would be nice.
    There is no displayport on this mid 2011 Mac mini.
    There does not seem to be any HDMI to VGA nor  Thunderbolt to VGA adapters on the market.
    Any suggestions?

    The > Apple - Thunderbolt Port is the same as and doubles as a Mini DisplayPort.
    Look down at the bottom of > Mac mini (Mid 2011) - Technical Specifications in the Accessories / Displays and Graphics section or on page #33 of your User Guide.

  • MacBook Pro to VGA monitor

    What adapter should I use to connect my MacBook Pro to my VGA monitor?

    If you have MiniDisplay port or Thunderbolt then you need a MiniDisplay port to VGA adapter and a VGA cable.
    http://store.apple.com/us/product/MB572Z/A?fnode=MTY1NDA3Ng&s=topSellers

Maybe you are looking for