Sun Netra 240 runs max level POST every power up

Hello, I have a Sun Netra 240 server box that on every power up runs the max level POST which takes a good 5 minutes to complete. I have the power key switch set to the normal position and not DIAG mode and I have the Diag-level set to "off" for the system configuration settings. Nothing gets reported as an error during the POST but it still continues to run full POST on every power cycle. Can anyone tell me what else to check or look at to make it stop? Thanks in advance.

I have no way to get a copy of this from the screen so I had to write it all down and hand jam it in. I only put my values, not the default values. These have not been changed though so I don't think it is any of these settings. Just for some background this server has been fine for the past year or so and then one day it just started doing this out of the blue.
test-args -
diag-passes 1
asr-policy normal
local-mac-address? true
fcode-debug false
silent-mode? false
scsi-initiator-id 7
oem-logo -
oem-logo? false
oem-banner -
oem-banner? false
ansi-terminal true
screen-#col 80
screen-#row 34
ttyb-rts-dtr-off false
ttyb-ignore-cd true
ttya-rts-dtr-off false
ttya-ignore-cd true
ttyb mode 9600,8,n,1,-
ttya mode 9600,8,n,1,-
output-device screen
input-device keyboard
auto-boot-on-error false
load base 16384
auto-boot? true
boot-command boot
diag-device disk
use-NVRAMRC true
security mode command
NVRAMRC devalias radbkup
security-#bad-logins 2
post-trigger power-on-reset
diag-script none
diag-level off
diag-switch false
obdiag-trigger power-on-reset
error-reset-recovery boot
Edited by: 941057 on Jun 15, 2012 2:38 PM

Similar Messages

  • Netra 240 - SSH not working

    We are having a problem with a Sun Netra 240 � (Solaris 10) and are unable to SSH to the server. When entering the login and password � after about 15 seconds it closes out. We had NO trouble last week logging in using secure shell.
    We can go to the console port with no problem.
    Any ideas as to what might be the problem or fix?
    Thanks,

    You'll have to upgrade your IOS & license-
    "ENTERPRISE PLUS IPSEC 3DES-Supports all the ENTERPRISE PLUS features, plus adds support for Triple Digital Encryption Standard (3DES) encryption to enable features that require this security, such as Secure Shell (SSH) Protocol and IP Security (IPSec) tunnels"
    Hope it helps

  • Installation failed when using Jumpstart Server to install SUN Netra T1 200

    I have a problem to install a couple of Sun Netra T1 200 Servers with a Jumpstart Server. The Jumpstart Server is set up and I have executed the add_install_client Script. If I boot the Server which should to be installed the server crashes after getting the assigned IP-Address with a software fault.
    Attached i will sent the Jumpstart-Client-Output and the config Files of the Jumpstart-Server.
    ****Netra T1 Server Output, while configured as an Jumpstart client:****
    ok boot net -install
    Resetti
    LOM event: +2h28m47s host reset
    ng ...
    `
    Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
    OpenBoot 4.0, 1024 MB memory installed, Serial #16692502.
    Ethernet address 8:0:20:fe:b5:16, Host ID: 80feb516.
    Executing last command: boot net -install
    Boot device: /pci@1f,0/pci@1,1/network@c,1 File and args: -install
    Timeout waiting for ARP/RARP packet
    Timeout waiting for ARP/RARP packet
    Timeout waiting for ARP/RARP packet
    Timeout waiting for ARP/RARP packet
    2ae00 Warning: boot will not enable cache
    Requesting Internet address for 8:0:20:fe:b5:16
    Enter filename [kernel/sparcv9/unix]:
    Enter default directory for modules [platform/SUNW,UltraAX-i2/kernel /platform/sun4u/kernel /kernel /usr/kernel]:
    SunOS Release 5.8 Version Generic_108528-13 64-bit
    Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
    whoami: no domain name
    panic[cpu0]/thread=300010a9ba0: Can't invoke , error 2
    000002a1000f7a40 genunix:icode+274 (ffbefff0, 0, 300010a7b88, 0, ffbefffc, ffffffffffffffff)
    %l0-3: 00000000ffbefffc 0000000000000000 0000000000002000 000002a10000fd20
    %l4-7: 0000000000000bb8 0000000010423a00 000000001041b2f8 00000000000007a9
    syncing file systems... done
    skipping system dump - no dump device configured
    rebooting...
    Resetti
    LOM event: +2h36m51s host reset
    ng ...
    p
    Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
    OpenBoot 4.0, 1024 MB memory installed, Serial #16692502.
    Ethernet address 8:0:20:fe:b5:16, Host ID: 80feb516.
    Executing last command: boot
    Boot device: disk File and args:
    SunOS Release 5.8 Version Generic_108528-13 64-bit
    Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
    configuring IPv4 interfaces: eri0.
    Hostname: infrasrv
    The system is coming up. Please wait.
    checking ufs filesystems
    /dev/rdsk/c1t0d0s4: is stable.
    /dev/rdsk/c1t0d0s6: is stable.
    Starting IPv4 routing daemon.
    starting rpc services: rpcbind done.
    Setting netmask of eri0 to 255.255.255.0
    Setting default IPv4 interface for multicast: add net 224.0/4: gateway infrasrv
    syslog service starting.
    Print services started.
    Jun 26 04:48:14 infrasrv sendmail[220]: My unqualified host name (infrasrv) unknown; sleeping for retry
    volume management starting.
    The system is ready.
    infrasrv console login: root
    Password:
    Last login: Thu Jun 26 02:13:59 on console
    Jun 26 04:48:24 infrasrv login: ROOT LOGIN /dev/console
    Sun Microsystems Inc. SunOS 5.8 Generic Patch October 2001
    Sun Microsystems Inc. SunOS 5.8 Generic Patch October 2001
    # uname -i
    SUNW,UltraAX-i2
    # ^[[A
    ^[[A: not found
    # uname -m
    sun4u
    *****Config Files of the Jumpstart-Server******************
    Sysidcfg
    bootparams
    bash-2.03# more bootparams
    infrasrv  root=adminws:/cdrom/sol_8_202_sparc/s0/Solaris_8/Tools/Boot install=ad
    minws:/export/install boottype=:in sysid_config=adminws:/export/sysidcfg install
    _config=adminws:/export/config rootopts=:rsize=32768
    bash-2.03#
    rules
    bash-2.03# more rules
    #       @(#)rules 1.12 94/07/27 SMI
    # The rules file is a text file used to create the rules.ok file for
    # a custom JumpStart installation. The rules file is a lookup table
    # consisting of one or more rules that define matches between system
    # attributes and profiles.
    # This example rules file contains:
    #   o syntax of a rule used in the rules file
    #   o rule_keyword and rule_value descriptions
    #   o rule examples
    # See the installation manual for a complete description of the rules file.
    # RULE SYNTAX:
    # [!]rule_keyword rule_value [&& [!]rule_keyword rule_value]... begin profile fi
    # nish
    # "[ ]" indicates an optional expression or field
    # "..." indicates the preceding expression may be repeated
    # "&&" used to "logically AND" rule_keyword and rule_value pairs together
    # "!" indicates negation of the following rule_keyword
    # rule_keyword a predefined keyword that describes a general system
    # attribute. It is used with the rule_value to match a
    # system with the same attribute to a profile.
    # rule_value a value that provides the specific system attribute
    # for the corresponding rule_keyword. A rule_value can
    # be text or a range of values (NN-MM).
    # To match a range of values, a system's value must be
    # greater than or equal to NN and less than or equal to MM.
    # begin a file name of an optional Bourne shell script
    # that will be executed before the installation begins.
    # If no begin script exists, you must enter a minus sign (-)
    # in this field.
    # profile a file name of a text file used as a template by the
    # custom JumpStart installation software that defines how
    # to install Solaris on a system.
    # finish a file name of an optional Bourne shell script
    # that will be executed after the installation completes.
    # If no finish script exists, you must enter a minus sign (-)
    # in this field.
    # Notes:
    # 1. You can add comments after the pound sign (#) anywhere on a line.
    # 2. Rules are matched in descending order: first rule through the last rule.
    # 3. Rules can be continued to a new line by using the backslash (\) before
    # the carriage return.
    # 4. Don't use the "*" character or other shell wildcards, because the rules
    # file is interpreted by a Bourne shell script.
    # RULE_KEYWORD AND RULE_VALUE DESCRIPTIONS
    # rule_keyword rule_value Type rule_value Description
    # any minus sign (-) always matches
    # arch text system's architecture type
    # domainname text system's domain name
    # disksize text range system's disk size
    # disk device name (text)
    # disk size (MBytes range)
    # hostname text system's host name
    # installed text text system's installed version of Solaris
    # disk device name (text)
    # OS release (text)
    # karch text system's kernel architecture
    # memsize range system's memory size (MBytes range)
    # model 'text' system's model number
    # network text system's IP address
    # totaldisk range system's total disk size (MBytes range)
    # RULE EXAMPLES
    # The following rule matches only one system:
    # hostname sample_host - host_class set_root_pw
    # The following rule matches any system that is on the 924.222.43.0 network
    # and has the sun4c kernel architecture:
    # Note: The backslash (\) is used to continue the rule to a new line.
    #network 924.222.43.0 && \
    # karch sun4c - net924_sun4c -
    # The following rule matches any sparc system with a c0t3d0 disk that is
    # between 400 to 600 MBytes and has Solaris 2.1 installed on it:
    #arch sparc && \
    # disksize c0t3d0 400-600 && \
    # installed c0t3d0s0 solaris_2.1 - upgrade -
    # The following rule matches all x86 systems:
    #arch i386 x86-begin x86-class -
    # The following rule matches any system:
    #any - - any_machine -
    hostname infrasrv - infrasrv_class -
    hostname msm_srv1 - msm_srv_class -
    hostname msm_srv2 - msm_srv_class -
    bash-2.03#
    class
    bash-2.03# more infrasrv_class
    install_type initial_install
    system_type standalone
    partitioning explicit
    filesys c0t0d0s0 2048 /
    filesys c0t0d0s1 10
    filesys c0t0d0s3 1024 swap
    filesys c0t0d0s4 2048 /var
    filesys c0t0d0s5 2048 /opt
    filesys c0t0d0s6 free /export
    cluster SUNWCXall
    bash-2.03# more msm_srv_class
    install_type initial_install
    system_type standalone
    partitioning explicit
    filesys c0t0d0s0 2048 /
    filesys c0t0d0s1 10
    filesys c0t0d0s3 1024 swap
    filesys c0t0d0s4 2048 /var
    filesys c0t0d0s5 free /opt
    cluster SUNWCXall
    bash-2.03#
    ethers
    bash-2.03# more ethers
    8:00:20:fe:b5:16 infrasrv
    bash-2.03#
    hosts
    bash-2.03# more hosts
    # Internet host table
    127.0.0.1 localhost
    192.168.0.220 adminws loghost
    192.168.0.210 infrasrv
    192.168.0.200 tc
    bash-2.03#
    dfstab
    bash-2.03# more dfstab
    # Place share(1M) commands here for automatic execution
    # on entering init state 3.
    # Issue the command '/etc/init.d/nfs.server start' to run the NFS
    # daemon processes and the share commands, after adding the very
    # first entry to this file.
    # share [-F fstype] [ -o options] [-d "<text>"] <pathname> [resource]
    # .e.g,
    # share -F nfs -o rw=engineering -d "home dirs" /export/home2
    share -d "jumpstart conf dir" /export/config
    share -F nfs -o ro,anon=0 /export/install
    share -F nfs -o ro,anon=0 /cdrom/sol_8_202_sparc/s0/Solaris_8/Tools/Boot
    bash-2.03#
    tftpboot
    bash-2.03# pwd
    /tftpboot
    bash-2.03# ls -al
    total 348
    drwxrwxr-x 2 root other 512 Jun 26 11:45 .
    drwxr-xr-x 24 root root 512 Jun 26 11:45 ..
    lrwxrwxrwx 1 root other 26 Jun 26 11:45 C0A800D2 -> inetboot.SUN4U.Solaris_8-1
    lrwxrwxrwx 1 root other 26 Jun 26 11:45 C0A800D2.SUN4U -> inetboot.SUN4U.Solaris_8-1
    -rwxr-xr-x 1 root other 159416 Jun 26 11:45 inetboot.SUN4U.Solaris_8-1
    -rw-r--r-- 1 root other 318 Jun 26 11:45 rm.192.168.0.210
    lrwxrwxrwx 1 root other 1 Jun 26 11:45 tftpboot -> .
    bash-2.03#

    Hi,
    It seems to me that you have not created a proper sysidcfg file. From your post, it looks to me like your sysidcfg contains no entries. This is why it prompts you to enter the kernel path. Look on docs.sun.com for a guide to creating the sysidcfg file .

  • Sun Netra T5220 will not poweron (FATAL: Polling POK Status Time Out)

    Hey All,
    New to the forums here.
    We have a SUN Netra T5220 which we are unable to poweron, failing with a couple FATAL errors.
    sc> showlogs
    Log entries since Apr 20 07:48:41
    Apr 20 07:48:41: Chassis |critical: "CRITICAL ALARM is set"
    Apr 20 07:48:41: Chassis |critical: "CRITICAL ALARM is set"
    Apr 20 07:48:41: Chassis |critical: "Host has been powered off"
    Apr 20 07:52:23: Audit |minor : "root : Set : object = /SYS/power_state : value = on : success"
    Apr 20 07:52:33: Chassis |critical: "Apr 20 07:52:33 *FATAL: Polling POK Status Time Out: 0x9f*"
    Apr 20 07:52:33: Chassis |critical: "Apr 20 07:52:33 *FATAL: The HOST Processor has a configuration error, forcing a power-down*"
    Apr 20 07:52:33: Chassis |critical: "CRITICAL ALARM is set"
    Apr 20 07:52:33: Chassis |critical: "Host has been powered off"
    Apr 20 08:04:32: Audit |minor : "root : Set : object = /SYS/power_state : value = on : success"
    Apr 20 08:04:42: Chassis |critical: "Apr 20 08:04:42 FATAL: Polling POK Status Time Out: 0x9f"
    Apr 20 08:04:42: Chassis |critical: "Apr 20 08:04:42 FATAL: The HOST Processor has a configuration error, forcing a power-down"
    Apr 20 08:04:42: Chassis |critical: "CRITICAL ALARM is set"
    Apr 20 08:04:43: Chassis |critical: "Host has been powered off"
    Apr 20 08:07:54: Audit |minor : "root : Close Session : object = /session/type : value = console : success"
    Apr 20 08:08:10: Audit |minor : "admin : Open Session : object = /session/type : value = console : success"
    Apr 20 08:12:59: Audit |minor : "admin : Set : object = /SYS/power_state : value = on : success"
    Apr 20 08:13:09: Chassis |critical: "Apr 20 08:13:09 FATAL: Polling POK Status Time Out: 0x9f"
    Apr 20 08:13:09: Chassis |critical: "Apr 20 08:13:09 FATAL: The HOST Processor has a configuration error, forcing a power-down"
    Apr 20 08:13:10: Chassis |critical: "CRITICAL ALARM is set"
    Apr 20 08:13:10: Chassis |critical: "Host has been powered off"
    sc> showfaults
    Last POST Run: Sat Mar 26 06:38:35 2011
    Post Status: Passed all devices
    No failures found in System
    curious if any of you all have seen this type of error before and what may be the resolution.
    Thanks in advance for any responses,
    rbrociek

    rbrociek,
    It looks like the system board or power distribution board is faulty.
    You should open a SR in My Oracle Support.
    Regards.

  • How to set tree max level in V4+ trees?

    I have a tree and I want it to initally open up to level 3. (Not expand all). Previous to V4 you could set the attribute "Max Levels". How do you set this now? I assume it will be a dynamic action javascript call but what is the code?
    thanks in advance
    PaulP
    Edited by: PaulP on Apr 5, 2012 11:13 PM
    Edited by: PaulP on Apr 5, 2012 11:14 PM

    I searched through the docs of jstree 0.9.9a2, which comes with apex 4+, and through apex.widget.tree, but couldn't find any function which does what you describe. However, it can be emulated fairly easily.
    Add this code to the page javascript:
    function resetAndOpenToLevel ( pTree, pMaxLevel ) {
       apex.jQuery.tree.reference(pTree).close_all();
       $("ul", pTree).each(function ( index ) {
          if ( $(this).parents("ul").length <= pMaxLevel ) {
             apex.jQuery.tree.reference(pTree).open_branch(this);
    };When called this will open up the nodes of the given tree up to (and including) pMaxLevel.
    For convenience, give your tree region a static ID.
    For example,define a button which triggers a dynamic action with execute javascript code as true action:
    resetAndOpenToLevel ( $("#my_tree_region_id div.tree"), 2) ;Would reset the tree, and then open nodes up to and including level 2.
    You can try it out on my example tree page, where i included this code: http://apex.oracle.com/pls/apex/f?p=54687:38 There I'm using a global javascript variable to store a reference to the tree element rather than fetching it every time.

  • Min & Max level

    Hi
    My client insist on the maintenance Min & Max level at storage location, however i can not maitain in standard MM.
    If i develop a separate application for maintaing Min & Max level what will be the effects on MIGO when i do Issue or Receipts.
    In this senario i will have to develop an additional check on every Movement of Materials (Issue & Receipts).
    Kindly help me out.
    Regards
    Muhammad Tahir

    Hi Tahir ,
    As said by you . the requirement cannot be fulfilled in MM.
    You may try at BIN level provided WM is implemented in your Org.
    As a storage location may consists of different materials with different stock units ( Min and Max levels will again differ ) , i doubt your req may not be fulfilled .
    Regards
    Ramesh Ch

  • Tree : max level and initially expanded

    Hi,
    we have build a tree region that shows our organization. If we set the max level to a given value (say 2) it will open the tree with the first two levels expanded (as expected).
    If we expand more levels, it will shift the description of non-leaf nodes that are beyond the max level. This seems to be due to a problem in the calculation of the #COLSPAN# pseudo columns.
    Does anyone have similar experience? Did you find a workaround?
    Thx in advance
    Daniel

    I searched through the docs of jstree 0.9.9a2, which comes with apex 4+, and through apex.widget.tree, but couldn't find any function which does what you describe. However, it can be emulated fairly easily.
    Add this code to the page javascript:
    function resetAndOpenToLevel ( pTree, pMaxLevel ) {
       apex.jQuery.tree.reference(pTree).close_all();
       $("ul", pTree).each(function ( index ) {
          if ( $(this).parents("ul").length <= pMaxLevel ) {
             apex.jQuery.tree.reference(pTree).open_branch(this);
    };When called this will open up the nodes of the given tree up to (and including) pMaxLevel.
    For convenience, give your tree region a static ID.
    For example,define a button which triggers a dynamic action with execute javascript code as true action:
    resetAndOpenToLevel ( $("#my_tree_region_id div.tree"), 2) ;Would reset the tree, and then open nodes up to and including level 2.
    You can try it out on my example tree page, where i included this code: http://apex.oracle.com/pls/apex/f?p=54687:38 There I'm using a global javascript variable to store a reference to the tree element rather than fetching it every time.

  • How can system ensure to always make replenish qty to Max level?

    Hello,
    I have following query related to posting change in WM
    MAX qty --- 100
    Min qty---      50
    How should I make the stock to Max 100 always when available stock falls below 50?  For ex- if available stock is 49 or 30, or 2 or anything below 50 then system should always replenish it to 100 from Replenishment bin
    I believe when replenished qty in material master is 50 and stock is below 50 then system will replenish 50 qty. How can system ensure to always make replenish qty to Max level?
    Thanks,
    MMC

    Hi,
    Keep the replinish qty as zero in WM2 view of MMR.
    Go to LP21 and see if the requetsed qty is now 100.
    If you keep some qty as replinish qty, the same qty is always proposed as requested qty (TR qty)
    regards
    Shashidhar

  • Line items to be excuded in dunning after tha max. level is reached

    Hello everyone,
    We have a requirement in Dunning where the line items that have reached the max. level,  should not be included in the reminders any longer since the invoices are then handled over to an insurance company. Request help on the configuration required for this.
    Thanks

    Hello,
    The dunning block should be set at document level in this case. This way only the document will be blocked.
    If you set it in customer master, the customer will never be dunned.
    There is a path in customizing to create the dunning block.
    REgards,
    REnan Correa

  • Problem On Sun Netra 210 Network

    Hi All,
    Why does my sun netra 210 cannot passed the network packet over HP Procurve 3500yl Core Switch?
    But, no problem occured when i use Cisco Catalyst Core Switch.
    Is there any incompability between Sun and Hp Procurve, or i need to install new patches? Please help me.
    Thankyou in advance

    Dear sir,
    i already tried that,
    i also have try to use another port on the switch.
    The strange thing is, when i use laptop (with the same ipadress as the Sun), other computer from another segment can ping, But, when i returned the ipadress to the Sun server, they cannot ping (RTO).

  • Serial Port not accessible until I run MAX

    Hi!
    On my machine I can access all Serial ports perfectly. I put a Vias Resource in my VI and get a drop down menu with all my serial ports. But on other machines (Runtime v7 and VISA runtime installed) I don´t get the names (e.g. com1 com2) but only
    ASRL1:****
    ASRL2:****
    ASRL10:****
    I know that ASRL1 is COM1 but when I select it it dowsn´t work.
    If I now install MAX on the machine and run it once without changing the configuration my ports work.
    Can anybody tell me how to use the ports without using MAX??
    regards
    hmann

    Hi hmann,
    When you run MAX it is configuring your VISA alias list behinf the scenes. See "JB" answer to this question to find out how to do this without using MAX. It basicly requires editing an INI file.
    http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=506500000008000000238D0000&UCATEGORY_0=_49_%24_6_&UCATEGORY_S=0
    I hope this help,
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • Run a cron job every minute

    Hi,
    I would like to run a cron job every minute.
    I can find cron.hourly, cron.daily, cron.weekly, cron.monthly in my /etc, but no cron.minutly.
    Can I get it? What should I do?
    Thanks!
    Nathan

    run
    crontab -e
    . this opens an editor. therein you type :
    #min hour day month weekday command
    */1 * * * * <your command>
    dw was faster
    Last edited by DonVla (2008-11-17 16:56:42)

  • Down-level Poster.png just a white box on IE8

    Hi everyone,
    I've created a very simple Edge Animate banner consisting of a background image and two layers of text that fade in, it shows up perfectly in everything except for (understandably) IE8 and I assume IE7, all I see is a white box.
    I inserted the animation via Dreamweaver using Insert/Media/Edge Animate Composition, it went into a "mainbanner" div with CSS:
    #mainbanner {
              clear:both;
              width: 1000px;
              margin: 0 auto;
              border: 0;
              padding: 10px;
    These code lines have been inserted into the <head> section of the Dreamweaver template and subsequent index.php page:
    <meta http-equiv="X-UA-Compatible" content="IE=Edge"/>
    <meta http-equiv="Content-Type" content="text/html; charset=UTF-8" />
    This code was applied to the "mainbanner" div by Dreamweaver after doing Insert/Media/Edge Animate Composition:
    <!-- The following tag displays an Edge Animate Composition -->
    <object id="EdgeID" name="EdgeID" type="text/html" width = "1020" height ="437" data ="../edgeanimate_assets/jb_mainbanner/Assets/jb_mainbanner.html" >
    </object></div>
    Don't know why the animation that has 1000px width has a width of 1020px shown in code when imported yet shows correctly as 1000px in the browser but hey!
    I've checked that the down-level poster (Poster.png) I created has been linked to the animation; has been uploaded to the web server; is showing the appropriate static version of the animation but after one whole night of trying everything I can think of all I still get on IE8 is a white box!
    Can someone please give me some help with this, many thanks in advance.
    Chris

    I've just made the Poster.png appear on IE8 by extending the CSS #mainbanner width to 1020px (despite the image being 1000px) and removing the padding temporarily. However two issues still remain:
    The image is now not aligned with the header and footer so I need to insert padding again plus there is a still a white box behind the .png that I simply don't want!
    At least I have made some progress since waking up this morning with a fresh head!
    How can I remove the white box that looks like a placeholder behind the static png on IE8?

  • Run MAX,message'Initialization of C:\WINNT\System32\nipalu.dll failed. Why?

    The problem is that Max will not open correctly, therefore rendering Labview useless as it can not use any of the PCI Cards in the PC.
    When MAX is run, the program opens as normal, i.e. it presents the MAX explorer screen. Approximately 2 seconds later it displays the message:
    Initialization of the dynamic link library C:\WINNT\System32\nipalu.dll failed.
    The process is terminating abnormally.
    therefore labview cannot detect any devices or signal names.

    I have had the problem fixed after a trip NI
    Im putting the fix on this forum incase anybody else is having the same problem, or has it occur in the future.
    In short for some reason, Labview has moved the nipalu.dll file from its original place in memory, therefore MAX can not find it to initialize it.
    Steps for correction:
    1) Download palBase Utility from NI.COM
    2) Copy palBase Utility onto the C: Drive on the PC
    3) Go to the START menu and select RUN
    4) type COMMAND and press Enter
    5) In the command prompt type
    palBase -b 69000000 -s 45000000
    6) When successful message appears, type exit and enter
    7) re-boot PC and run MAX - All should work correctly
    8) DELETE palBase from C: Drive

  • Netra  240 Key switch position chnage to UNKNOWN

    I cannot boot up NETRA 240 , the key switch position is change to UNKNOWN even if the rotary switch is set up to NORMAL position!
    I boot up the NETRA in using bootmode option skip_diag but after a while the system goes down and I cannot boot up after!
    SEP 21 02:31:51 spatialnetra9: 00040076: "Keyswitch position has been changed to UNKNOWN."
    SEP 21 02:50:33 spatialnetra9: 00060000: "SC Login: User admin Logged on."
    SEP 21 04:02:30 spatialnetra9: 0004000a: "SC set bootmode to skip_diag, will expire THU SEP 21 04:12:30 UTC 2006."
    SEP 21 04:02:42 spatialnetra9: 00040001: "SC Request to Power On Host."

    Unfortunately, we do not use netmgt port (it is disconnected).
    Even though, I can not use login and pass info in script (security reasons).

Maybe you are looking for

  • How do I get my gmail account unlocked, it has been hacked and even security questions changed. I can't access the account to change the password.

    Someone used one of my two gmail accounts to send emails to both of my gmail accounts and one of my yahoo accounts - using all my contacts on the three accounts - saying I was in Scotland and needed money, please send it. I have changed the password

  • No Update in Transformation Routine (CX_RSROUT_SKIP_RECORD)

    Hi , Please find the below scenario DSO Level 1 We have 2 Key fileds  (Trial No and Event No) and the data is given below Trial No       Event No       Date 1212           440                Jan 1st 2011 1212           670                Feb 8th 2011

  • New iMac and Final Cut Pro 4?

    I recently bought the new 20" iMac. After installing FCPro 4, I got the message that I cannot run FCPro 4 because I do not have the AGP card installed. Is there a way around this on the iMac?

  • Updating model for pivot table in af:iterator

    Using Master Detail relationship, i am trying to create multiple forms at runtime. I want to show all the forms at once. Each form has some header fields and a pivot table. Header field is coming from master table and pivot table should be made from

  • WD ABAP: Drag and drop functionality

    Hi, Is there a UI element/event to simulate the drag and drop functionality in Webdynpro ABAP? I would like to simulate the functionality of context mapping. I have the requirement to show the hierarchy of say Country and state(preferably in tree str